446419
28
Verklein
Vergroot
Pagina terug
1/112
Pagina verder
28
ENGLISH
D25104K - Replacing the tool holder with
the chuck (fig. G)
Turn the locking collar (8) into the unlocking
position and pull the tool holder (6) off.
Push the chuck (13) onto the spindle and turn the
locking collar into the locking position.
To replace the chuck with the tool holder,
first remove the chuck the same way as the tool
holder was removed. Then place the tool holder
the same way as the chuck was placed.
Never use standard chucks in the
hammer drilling mode.
Replacing the dust cover (fig. C)
The dust cover (7) prevents dust ingress into the
mechanism. Replace a worn dust cover immediately.
Pull back the tool holder locking sleeve (12) and
pull the dust cover (7) off.
Fit the new dust cover.
Release the tool holder locking sleeve.
Instructions for use
Always observe the safety instructions
and applicable regulations.
Be aware of the location of pipework and wiring.
Apply only a gentle pressure to the tool
(approx. 5 kg). Excessive force does not speed
up drilling but decreases tool performance and
may shorten tool life.
Do not drill or drive too deep to prevent damage
to the dust cover.
Always hold the tool firmly with both hands
and ensure a secure stance (fig. H).
Always operate the tool with the side
handle properly mounted.
Switching on and off (fig. A)
D25102(K)/D25102C/D25103K/D25104K
To run the tool, press the variable speed switch
(1). The pressure exerted on the variable speed
switch determines the tool speed.
For continuous operation, press and hold down
the variable speed switch, press the lock-on
button (2) and release the switch.
To stop the tool, release the switch.
To stop the tool in continuous operation, press
the switch briefly and release it. Always switch off
the tool when work is finished and before
unplugging.
D25203K
To run the tool, press the variable speed switch
(1). The pressure exerted on the variable speed
switch determines the tool speed.
To stop the tool, release the switch.
To lock the tool in off position, move the forward/
reverse slider (3) to the central position.
Hammer drilling (fig. A)
Drilling with a solid bit
Set the mode selector switch (4) to the
“hammer drilling” position.
Insert the appropriate drill bit. For best results
use high quality carbide-tipped bits.
Adjust the side handle (9) as required.
If necessary, set the drilling depth.
Mark the spot where the hole is to be drilled.
Place the drill bit on the spot and switch on the
tool.
Always switch off the tool when work is finished
and before unplugging.
Drilling with a core bit
Set the mode selector (3) to the “hammer drilling”
position.
Adjust the side handle (9) as required.
Insert the appropriate core bit.
Assemble the centerdrill into the core bit.
Place the centerdrill on the spot and press the
variable speed switch (1). Drill until the core
penetrates into the concrete approx. 1 cm.
Stop drilling and remove the centerdrill. Place the
core bit back into the hole and continue drilling.
When drilling through a structure thicker than the
depth of the core bit, break away the round
cylinder of concrete or core inside the bit at
regular intervals. To avoid unwanted breaking
away of concrete around the hole, first drill a hole
the diameter of the centerdrill completely through
the structure. Then drill the cored hole halfway
from each side.
28

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt D25104K bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt D25104K in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 0,67 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info