446415
27
Verklein
Vergroot
Pagina terug
1/112
Pagina verder
27
ENGLISH
In this mode the tool can also be used as
a lever to free a jammed drill bit.
Bit rotation: non-working position used
only to rotate a flat chisel into the desired
position.
To select the operating mode, press the safety
lock (5) and rotate the mode selector switch (4)
until it points to the symbol of the required mode.
Release the safety lock and check that the mode
selector switch is locked in place.
Do not select the operating mode when
the tool is running.
Indexing the chisel position
The chisel can be indexed and locked into 51
different positions.
Rotate the mode selector switch (4) until it points
to the “bit rotation” position.
Rotate the chisel in the desired position.
Set the mode selector switch (4) to the
“hammering only” position.
Twist the chisel until it locks in position.
Inserting and removing SDS-plus
®
accessories
(fig. C)
This tool uses SDS-plus
®
accessories (refer to the
inset in fig. B for a cross-section of an SDS-plus
®
bit
shank).
We recommend to use professional accessories only.
Clean and grease the bit shank.
Insert the bit shank into the tool holder (6).
Push the bit down and turn it slightly until it fits
into the slots.
Pull on the bit to check if it is properly locked.
The hammering function requires the bit to be
able to move axially several centimetres when
locked in the tool holder.
To remove a bit pull back the tool holder locking
sleeve (12) and pull out the bit.
Fitting the side handle (fig. D)
The side handle (10) can be fitted to suit both
RH- and LH-users.
Always use the tool with the side handle
properly assembled.
Loosen the side handle.
For RH-users, slide the side handle clamp over the
collar behind the tool holder, handle at the left.
For LH-users, slide the side handle clamp over
the collar behind the tool holder, handle at the
right.
Rotate the side handle to the desired position
and tighten the handle.
Setting the drilling depth (fig. E)
Insert the required drill bit as described above.
Press the depth stop clamp (11) and keep it
depressed.
Fit the depth adjustment rod (9) through the hole
in the depth stop clamp.
Adjust the drilling depth as shown.
Release the depth stop clamp.
Forward/reverse slider (fig. F1 & F2)
D25102(K)/D25102C/D25103K/D25104K (fig. F1)
Push the forward/reverse slider (3) to the RH-side
for forward (RH) rotation. See arrows on tool.
Push the forward/reverse slider (3) to the LH-side
for reverse (LH) rotation.
D25203K (fig. F2)
Push the forward/reverse slider (3) to the LH-side
for forward (RH) rotation. See arrows on tool.
Push the forward/reverse slider (3) to the RH-side
for reverse (LH) rotation.
Always wait until the motor has come to
a complete standstill before changing the
direction of rotation.
D25102(K)/D25102C/D25103K/D25203K -
Fitting the chuck adapter & chuck
Screw the chuck onto the threaded end of the
chuck adapter.
Insert the connected chuck and adapter in the
tool as though it were a standard SDS-plus
®
bit.
To remove the chuck, proceed as for removing a
standard SDS-plus
®
bit.
Never use standard chucks in the
hammer drilling mode.
27

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt D25102 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt D25102 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 0,67 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info