79080
42
Verklein
Vergroot
Pagina terug
1/192
Pagina verder
ENGLISH
40
CAUTION: If the guard cannot be
tightened by the adjusting screw, do
not use the tool. To reduce the risk of
personal injury, take the tool and guard
to a service center to repair or replace
the guard.
Fitting and Removing a Grinding or
Cutting Disc (fi g. 3–5)
WARNING: Do not use a damaged
disc.
1. Place the tool on a table, guard up.
2. Fit the backing flange (j) correctly onto the
spindle (k) (fig. 3).
3. Place the disc (l) on the backing flange (j) (fig. 4).
When fitting a disc with a raised center, make
sure that the raised centre (m) is facing the
backing flange (j).
4. Screw the threaded clamp nut (n) onto the
spindle (k) (fig. 5):
a. The ring on the threaded clamp nut (n) must
face towards the disc when fitting a grinding
disc (fig. 5A);
b. The ring on the threaded clamp nut (n) must
face away from the disc when fitting a cutting
disc (fig. 5B).
5. Press the spindle lock button (c) and rotate the
spindle (k) until it locks in position (fig. 4).
6. Tighten the threaded clamp nut (n) with the two-
pin spanner supplied.
7. Release the spindle lock.
8. To remove the disc, loosen the threaded clamp
nut (n) with the two-pin spanner.
Prior to Operation
Install the guard and appropriate disc or wheel.
Do not use excessively worn discs or wheels.
Be sure the inner and outer flange are mounted
correctly.
Make sure the disc or wheel rotates in the
direction of the arrows on the accessory and the
tool.
OPERATION
Instructions for Use
WARNING: Always observe the safety
instructions and applicable regulations.
WARNING: To reduce the risk
of serious personal injury, turn
tool off and disconnect tool from
power source before making any
adjustments or removing/installing
attachments or accessories. Before
reconnecting the tool, depress and
release the trigger switch to ensure that
the tool is off.
WARNING:
Ensure all materials to be ground or
cut are secured in place.
Apply only a gentle pressure to the
tool. Do not exert side pressure on the
disc.
Avoid overloading. Should the tool
become hot, let it run a few minutes
under no load condition.
Proper Hand Position (fi g. 1)
WARNING: To reduce the risk of
serious personal injury, ALWAYS use
proper hand position as shown.
WARNING: To reduce the risk of
serious personal injury, ALWAYS hold
securely in anticipation of a sudden
reaction.
Proper hand position requires one hand on the side
handle (e), with the other hand on the body of the
tool, as shown in figure 1.
Switching On and Off (fi g. 1)
The on/off switch is equipped with an unlocking
switch.
To run the tool, depress the unlocking switch (b) and
subsequently operate the on/off switch (a).
Release the unlocking switch (b).To stop the tool,
release the switch.
Spindle Lock (fi g. 1)
The spindle lock (c) is provided to prevent the
spindle from rotating when installing or removing
wheels. Operate the spindle lock only when the tool
is turned off, unplugged from the power supply, and
has come to a complete stop.
NOTICE: To reduce the risk of damage
to the tool, do not engage the spindle
lock while the tool is operating. Damage
to the tool will result and attached
accessory may spin off possibly
resulting in injury.
42

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt D 28432 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt D 28432 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 25,83 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van DeWalt D 28432

DeWalt D 28432 Gebruiksaanwijzing - Nederlands, Deutsch, English, Français, Italiano, Português, Espanôl, Espanõl, Polski, Türkiye, Dansk, Svenska, Norsk, Suomi - 96 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info