110214
35
Verklein
Vergroot
Pagina terug
1/140
Pagina verder
ENGLISH
33
If the supply cord is damaged, it must be replaced
by a specially prepared cord available through the
DEWALT service organisation.
Mains Plug Replacement
(U.K. & Ireland Only)
If a new mains plug needs to be fitted:
Safely dispose of the old plug.
Connect the brown lead to the live terminal in
the plug.
Connect the blue lead to the neutral terminal.
WARNING: No connection is to be
made to the earth terminal.
Follow the fitting instructions supplied with good
quality plugs. Recommended fuse: 13 A.
Using an Extension Cable
An extension cord should not be used unless
absolutely necessary. Use an approved extension
cable suitable for the power input of your charger
(see technical data). The minimum conductor size is
1 mm
2
; the maximum length is 30 m.
When using a cable reel, always unwind the cable
completely.
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of
injury, turn unit off and disconnect
machine from power source before
installing and removing accessories,
before adjusting or changing set-
ups or when making repairs. Be sure
the trigger switch is in the OFF position.
An accidental start-up can cause injury.
Depth of Cut Adjustment (fi g. 1–3)
1. Loosen the depth adjustment knob (n).
2. Move the shoe (f) to obtain the correct depth of
cut.
3. Tighten the depth adjustment knob (n).
WARNING: For optimal results, allow
the saw blade to protrude from the
workpiece by about 3 mm (see inset in
figure 3).
Bevel Adjustment (fi g. 4)
The bevel angle can be adjusted between 0° and
45° for the D23550 and between 0° and 55° for the
D23650.
1. Loosen the bevel adjustment knob (k).
2. Set the bevel angle by tilting the saw shoe (f)
until the mark indicates the desired angle on the
scale.
3. Tighten the bevel adjustment knob (k).
Shoe Adjustment for 90° Cuts
(fi g. 1, 5)
1. Adjust the saw to 0° bevel.
2. Retract the blade guard using the lever (h) and
place the saw on the blade side.
3. Loosen the bevel adjustment knob (k).
4. Place a square against the blade and shoe to
adjust the 90° setting.
5. Adjust the stop (o) as required.
Replacing the Saw Blade (fi g. 6)
1. Engage the blade lock button (d) and unscrew
the blade clamping screw (q) by turning
counterclockwise using the spanner (r) supplied
with the tool.
2. Retract the lower blade guard (i) using the
lever (h) and replace the blade (j). Reinstall the
washers (s, t) in the correct position.
3. Check the direction of rotation of the blade.
4. Thread on the blade clamping screw (q) by
hand to hold the washer in position. Turn
clockwise.
5. Press the blade lock button (d) while turning the
spindle until the blade stops rotating.
6. Tighten the blade clamping screw firmly using
the spanner.
Adjusting the Riving Knife (fi g. 6)
For the correct adjustment of the riving knife (g),
refer to the inset in figure 6. Adjust the clearance
of the riving knife after changing the saw blade or
whenever necessary.
1. Adjust the depth of cut to 0 mm to access the
clamping screws of the riving knife.
2. Loosen the screws (u) and pull out the riving
knife to its maximum length.
3. Adjust the clearance and tighten the screws
(torque: 4–5 Nm).
Mounting and Adjusting the Parallel
Fence (fi g. 7)
The parallel fence (o) is used for cutting parallel to
the edge of the workpiece.
35

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeWalt D 23550 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeWalt D 23550 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Turks, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 3,4 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info