133755

DeLonghi pac c110 Handleiding

4
Verklein
Vergroot
Pagina terug
1/15
Pagina verder
19
GB
Warnings
• This appliance is designed for home air conditioning and must not be used for other purposes.
• It is dangerous to modify or alter the characteristics of the appliance in any way.
•The appliance must be installed in conformity with national legislation regulating electrical equipment
and installations.
• If the appliance requires repair, contact a Service Centre authorised by the manufacturer only.
Repairs carried out by unauthorised personnel may be dangerous.
•f the power cable is damaged, it must be replaced by a qualified professional authorised by the
manufacturer only.
• This appliance must be used exclusively by adults.
• The appliance is not intended for use by persons (including children) with reduced physical, sensory
or mental capabilities, or lack of experience and knowledge, unless they have been given supervi-
sion or instruction concerning use of the appliance by a person responsible for their safety. Children
should be supervised to ensure that they do not play with the appliance.
•The appliance must be connected to an efficient earth system. Have your electrical circuit checked
by a qualified electrician.
• Do not use extension cables.
• Before cleaning or maintenance, always unplug the appliance from the mains socket.
• Do not move the appliance by pulling the power cable.
• Do not install the appliance in rooms containing gas, oil or sulphur. Do not install near sources of heat.
• Do not rest heavy or hot objects on top of the appliance.
•Clean the air filter at least once a week.
•Avoid using heating appliances near the air conditioner.
• Always transport the appliance upright or resting on one side.
•Use the appliance as described in this instruction manual only. As with all electrical equipment, whilst
the instructions aim to cover as many eventualities as possible, caution and common sense should be
applied when operating and installing this appliance.
•At the end of its working life, consign the appliance to a specialist collection centre.
• The materials used for packaging can be recycled. You are therefore recommended to dispose of
them in special differentiated waste collection containers.
• When putting the appliance away, do not cover with plastic bags.
• The refrigerant gas R407C conforms to EC regulations on the environment. Avoid perforating the refri-
gerant circuit of the appliance.
ENVIRONMENTAL INFORMATION: This equipment contains fluorinated greenhouse gases covered
by the Kyoto Protocol. It should only be serviced or dismantled by professional trained personnel
(R407C, GWP=1653).
• Keep the appliance at least 50 cm away from flammable substances (alcohol etc) or pressurised
containers (e.g. aerosol cans).
DESCRIPTION
1 control panel
2 air outlet grille
3 castors
4 handles
5 filter
6 evaporator air intake grille
7 air exhaust hose housing
8 condensate drain connection
9 power cable
10 flange with cap
11 suckers
12 air exhaust hose
13 window outlet
14 castor locks
15 remote control unit (certain models
only)
20
D
uring the summer, you feel comfortable at a temperature of between 24 and 27° C with a
relative humidity of about 50%.
An air conditioner removes excess moisture and heat from the room where it is located.
Compared with installed models, portable air conditioners have the advantage that they can be
moved from one room to another in the home or be transported from one building to another.
Hot air from the room is passed through a heat exchanger cooled by refrigerant gas. Excess heat
and moisture are removed from the air which is
then re-emitted into the room cooler and
dryer.
In single unit models, a small part of
this air is used to cool the refrige-
rant gas and then, when hot
and damp, is discharged outsi-
de.
In models with outdoor unit,
the circuit is cooled using air
from outside.
All Pinguino models can
also be used in fan-only
mode.
What is Pinguino?
21
GB
1
2
The instructions below will enable you to prepare your air conditioner for operation as efficiently
as possible.
Before use, make sure the air intake and outlet grilles are unobstructed.
AIR-CONDITIONING WITHOUT INSTALLATION
Just a few simple steps and your comfort is
ensured with Pinguino:
• Fit the air exhaust hose 12 in the housing 7 at
the back of the appliance. Insert as shown in
figure A.
• If you have a double window, use the
suckers 11 provided to hold the two parts
of the window together (fig. C).
• Fit the window outlet 13 to the end of the
hose 12.
• Place the air conditioner near a window
or French window.
• Make sure the air exhaust hose is unobstruc-
ted.
• Open the window or French window sligh-
tly and position the outlet 13 as shown in
figure B.
A
Preparing for use
B
C
Keep the air hoses as short and free of
curves as possible to avoid bottlenecks.
ELECTRICAL CONNECTIONS
Before plugging the appliance into the mains socket, check that:
• the mains power supply corresponds to the value indicated on the rating plate on the back of the appliance;
• the power socket and electrical circuit are adequate for the appliance.
• the mains socket matches the plug. If this is not the case, have the plug replaced;
• the mains socket is adequately earthed. Failure to follow these important safety instructions absolves the
manufacturer of all liability.
The power cable must be replaced by a qualified professional only.
22
Preparing for use
AIR-CONDITIONING WITH INSTALLATION
If required, the Pinguino can also be installed
semi-permanently (Fig. D).
• Fit the flange accessory provided 10 in the
hole
• Fissare il tubo 12 in the housing at the back
of the appliance (fig. A, page 21).
• Fit the end of the hose 12 to the flange
10
as shown in fig. F.
Proceed as follows:
• Drill a hole in an outside wall or through a
window pane. Respect the height and
dimensions of the hole as given in figures E
and F.
30 cm
30 cm
125
MAX100 cm
MIN 35
c
m
When the hose 12 is not fitted, the hole can
be closed with the flange cap 10.
NOTE:
When installing the air conditioner semi-per-
manently, you should leave a door slightly
open (as little as 1 cm) to guarantee correct
ventilation.
in the window
pane
in the wall: you are
recommended to
insulate the sec-
tion of wall using
suitable insulation.
in the woo-
den kick-
board of a
French win-
dow
E
F
Keep the air hoses as short and free of
curves as possible to avoid bottlenecks.
D
23
GB
Control panel
DESCRIPTION OF THE CONTROL PANEL
A ON/STAND-BY button
B MODE selection button
Air conditioning, dehumidifying, fan
C FAN speed selection button
D Timer button
E Programmed operation increase temperature/time button
F Programmed operation decrease temperature/time button
G Display showing the temperature values set and the programmed operating time
H Timer in operation light
I/L/M/N Fan speed and AUTO mode lights
O Fan mode light
P Dehumidifying mode light
Q Air-conditioning mode light
R Remote control receiver
D
AB
C
E
F
G
H
I
L
M N O P Q
R
24
Operating from the control panel
TURNING THE APPLIANCE ON
Plug into the mains socket.
Two lines appear on the display indicating that the appliance is
in stand-by.
Press the ON/STAND-BY button (A). When turned on, the air con-
ditioner starts operating in the same mode as when it was turned
off.
Press the MODE button (B) until the light corresponding to the
required mode lights up:
Light (Q): air-conditioning mode
Light (P): dehumidifying mode
Light (O) :fan mode
AIR-CONDITIONING MODE
Ideal for hot muggy weather when you need to cool and dehu-
midify the room.
To set operation of the appliance correctly, press the + (E) or - (F)
buttons until the desired temperature is displayed.
Then select the fan speed by pressing the FAN button (C) until the
light corresponding to the required fan speed lights up:
HIGH: the air conditioner operates at maximum to reach the
required temperature as rapidly as possible
MED:reduces noise levels but still maintains a good level of
comfort
LOW: for silent operation
AUTO: the appliance automatically selects the most suitable
fan speed in relation to the temperature set on the digi-
tal display.
The most suitable temperature for the room during the summer
varies from 24 to 27°C. You are recommended, however, not to
set a temperature much below the outdoor temperature.
25
25
GB
DEHUMIDIFYING MODE
Ideal for reducing humidity in spring and autumn, during rainy spells or in
damp rooms, etc.
In dehumidifying mode, the appliance must have the same configuration
as for the air conditioning mode, with the air exhaust hose fitted to the
appliance to allow air to be discharged externally.
For instructions on preparing for use, see the section "Air conditioning
without installation" (page 21). When the dehumidifying mode is selected,
the light (P) comes on and “ ” appears on the display.
At the same time, the AUTO fan light (N) comes on. In this mode, other
speeds cannot be selected.
FAN MODE
Adjust fan speed by pressing the FAN button (C) as described for the air-
conditioning mode.
In this mode, AUTO cannot be selected.
The fan speed selected will be displayed.
Operating from the control panel
SETTING THE TIMER
The timer can be used to delay appliance start up or shutdown. This avoids wasting electricity by
optimising operating periods.
How to programme delayed start up
• Plug the appliance into a mains socket and press the ON/STAND-BY button (A), then select the
required operating mode and other settings (temperature, fan speed, etc).
•Press the ON/STAND-BY button (A) again: The appliance switches to stand-by mode (the two
central segments are displayed).
•Press the TIMER button (D). The last timer setting or the preset value 6.0 flashes on the display.
• Use the + (E) or - (F) buttons to set the number of hours delay before the appliance comes on.
During the first ten hours, you can select half hour intervals. For times greater than ten hours,
one hour intervals can be selected. If the + (E) or - (F) buttons are pressed for more than 2
seconds, the time runs rapidly up to a maximum of 24 hours. Press the timer button again within
a few seconds to confirm the setting. If the setting is not confirmed within a few seconds, the
display resets to stand-by. With the timer activated, the countdown before the programmed
start up time is displayed and the light (H) flashes.
To cancel the timer programme, press the timer button (D) again.
How to programme delayed shutdown
• Delayed shutdown can be programmed in any operating mode (air conditioning/dehumi-
difying/fan).
•Press the TIMER button (D). The last timer setting or the preset value 6.0 flashes on the display.
• Use the + (E) or - (F) button to set the number of hours delay before the appliance goes off.
During the first ten hours, you can select half hour intervals. For times greater than ten hours,
one hour intervals can be selected.
If the + (E) or - (F) buttons are pressed for more than 2 seconds, the time runs rapidly up to a
maximum of 24 hours.
Press the timer button again within a few seconds to confirm the setting.
When the timer is set, the light (H) flashes.
At the set time, the air conditioner shuts down and remains in stand-by.
To cancel the timer programme, press the timer button (D) again.
26
Self-diagnosis
SELF-DIAGNOSIS
The appliance has a self diagnosis system to identify a number of malfunctions.
LOW TEMPERATURE
(frost prevention)
PROBE FAILURE
(sensor damaged)
FULL TANK
When the appliance is operating in dehumidifying mode, this device pre-
vents the formation of ice. The appliance starts up again automatically
when the defrosting process is completed.
If this is displayed, contact your local authorised service centre.
Empty the internal tank, see page 31 "End of season operations"
IF ... IS DISPLAYED ...WHAT SHOULD YOU DO?
27
GB
Using the remote control unit
(Certain models only)
CORRECT USE OF THE REMOTE CONTROL
• Point the remote control at the receiver
(R) on the air conditioner.
• Maximum distance: around 7 metres
(without any obstacles between the remote
control and the receiver).
• The remote control should be handled
with extreme care. Do not drop it, expose
it to direct sunlight, or sources of heat.
DESCRIPTION OF THE REMOTE CONTROL
16) FAN button
17) ON/OFF button
18) MODE button
19) TIMER button
20) Display
Inserting or replacing the batteries
• Remove the cover on the rear of the
remote control;
• Remove the flat batteries if present.
• Insert two R03 AAA 1.5V batteries, making
sure they are in the correct position (see
the instructions inside the battery com-
partment);
• Replace the cover.
If the remote control unit is replaced or
discarded, the batteries must be removed
and disposed of in accordance with current
legislation as they are harmful to the envi-
ronment.
20
16
17
19
18
28
Using the remote control unit
TURNING THE APPLIANCE ON
Plug into the mains socket.
Press the ON/OFF button 17 (when turned on, the air conditioner starts operating in the same
mode as when it was turned off).
Press the MODE 18 button to select the required mode
AIR-CONDITIONING (COOL)
DEHUMIDIFYING (DRY)
FAN ONLY (FAN)
An arrow on the display indicates the selected mode.
AIR-CONDITIONING MODE (COOL)
Ideal for hot humid weather when you need to cool and dehumidify the room.
In air-conditioning mode, use the buttons to select the desired temperature.
The display shows the set temperature.
To change the fan speed, use the FAN button 16 on the remote control, choosing from the avai-
lable speeds:
AUTO: the appliance automatically selects the most suitable fan speed in relation to the tem-
perature set on the digital display.
HIGH: the air conditioner operates at maximum to reach the required temperature as rapidly as
possible
MED: reduces noise levels but still maintains a good level of comfort
LOW: for silent operation
Two arrows on the display indicate respectively COOL and the fan speed.
The most suitable temperature for the room during the summer varies from 24 to 27°C. You are
recommended, however, not to set a temperature much below the outdoor temperature.
DEHUMIDIFYING MODE (DRY)
Ideal to reduce room humidity while avoiding temperature variations (spring and autumn, damp
rooms, rainy periods, etc).
In dehumidifying mode, the appliance selects fan speed automatically.
Two arrows on the remote control display indicate DRY and AUTO respectively.
FAN MODE ONLY (FAN)
In fan mode, fan speed can be set by pressing the FAN button 16.
The fan speed changes between the speeds available (LOW/MED/HIGH).
Two arrows on the display indicate FAN mode and the speed set.
In this mode, AUTO speed cannot be selected.
SETTING THE TIMER
The timer can be used to delay appliance start up or shutdown. This avoids wasting electricity by
optimising operating periods.
How to programme delayed shutdown
•With the air-conditioning unit on, press the TIMER button 19. The time is displayed and the "h"
symbol flashes, with a flashing arrow indicating TIMER OFF.
• Set the time when you want the appliance to go off using the buttons (from 30 minutes to
24 hours). During the first ten hours, you can select half hour intervals. For times greater than ten
hours, one hour intervals can be selected.
•Press the TIMER button again to confirm the selection. The appliance emits a beep and the
light (H) flashes on the control panel, confirming successful activation of the timer. A count-
down of the time left is displayed on the remote control display and the light (H) flashes on the
air conditioner display.
• At the end of the set time the appliance switches off automatically.
29
GB
•To cancel the timer programme, press the TIMER button again. The appliance emits a beep
and both displays reset to display the settings prior to activation of the timer.
How to programme delayed start up
•With the air conditioner off, press the TIMER button. An arrow indicating TIMER ON flashes on
the display. Now make all the desired settings for when the appliance will switch on (opera-
ting mode, fan speed and temperature). Confirm the settings by pressing the TIMER button. The
time is displayed and the "h" symbol flashes.
Set the time when you want the appliance to switch off using the buttons (from 30 minutes
to 24 hours).
During the first ten hours, you can select half hour intervals. For times greater than ten hours,
one hour intervals can be selected.
•Press the TIMER button again to confirm the start-up time. A beep sounds and the time set is
also displayed on the control panel, confirming setting of the timer. The light (H) flashes on the
air conditioner display. A countdown of the time left is displayed on both displays.
• At the end of the set time the appliance switches on automatically, with the settings made
previously.
•To cancel the timer programme, press the TIMER button again. The appliance emits a beep
and both displays reset to stand-by.
Using the remote control unit
30
To get the best from your air conditioner, fol-
low these recommendations:
•close the windows and doors in the room to
be air conditioned. The only exception is
when the appliance is installed through a
hole in the wall. In this case, you are recom-
mended to leave a slight draught through a
door or window to guarantee correct venti-
lation.
•Protect the room from direct exposure to
the sun by partially closing curtains and/or
blinds to make the appliance much more
economical to run;
• Never rest objects of any kind on the air
conditioner;
• Never obstruct the air intake 6 or outlet 2;
• Make sure there are no heat sources in the
room.
• Never use the appliance in very damp
rooms (laundries for example).
• Never use the appliance outdoors.
Tips
close doors and windows
close blinds or curtains
do not
cover the
appliance
• Make sure the air conditioner is standing
on a level surface. If necessary, place the
two castor locks 14 under the front wheels
3
.
… 4 …

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

DeLonghi-pac-c110

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DeLonghi pac c110 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DeLonghi pac c110 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,9 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van DeLonghi pac c110

DeLonghi pac c110 Gebruiksaanwijzing - Nederlands - 15 pagina's

DeLonghi pac c110 Gebruiksaanwijzing - Deutsch - 15 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info