4. Wash the cappuccino maker and steam nozzle
thoroughly with warm water.
5. Make sure the two holes shown in fig. 31 are not
blocked. If necessary, clean with a pin.
6. Replace the steam nozzle by inserting it in the
steam tube, lining up arrow A and notch B shown
in fig. 32.
7. Replace the milk frother by inserting it and rotating
anticlockwise (fig. 33).
HOT WATER PRODUCTION
1.Turn the appliance on by rotating the selector knob to
the position (fig. 14).
2.Place a recipient under the cappuccino maker.
3.When the OK indicator light comes on, position the
selector knob as shown (fig. 17) and at the same
time, rotate the steam knob anticlockwise (fig. 29).
Hot water is delivered from the cappuccino maker;
4.To interrupt delivery of hot water, rotate the steam
knob clockwise and position the selector knob to
"O".
CLEANING AND MAINTENANCE
1. When cleaning the coffee machine, do not use solvents or
abrasive detergents. A soft, damp cloth is sufficient.
2. Clean the filter holder cup, filters, drip tray and water tank
regularly.
IMPORTANT: during cleaning, never immerse the coffee
machine in water. It is an electrical appliance.
CLEANING THE FLAVOUR SAVER
To facilitate cleaning of the Flavour Saver, it can be removed
from the filter holder (R) by pulling it upwards (fig. 34). To
replace, just slide the Flavour Saver into the guides on the
inside edge of the drip coffee filter holder.
CLEANING THE FILTER HOLDER FOR GROUND
COFFEE
About every 300 coffees, clean the filter holder for
ground coffee as follows:
• Remove the filter with the frother;
• Clean the inside of the filter holder. Never wash in a
dishwasher.
• Unscrew the cap of the frother (fig. 35) by rotating in
the direction indicated by the arrow on the cap.
• Remove the frother from the container by pushing it
from the cap end.
• Remove the gasket (fig.38).
• Rinse all components and clean the metal filter
thoroughly in hot water using a brush (fig. 36). Make
sure the holes in the metal filter are not blocked. If
necessary, clean with a pin (see fig. 37).
• Replace the filter and gasket on the plastic disk as
shown in figure 38. Make sure to insert the pin on
the plastic disk into the hole in the gasket indicated
by the arrow in fig. 38.
• Replace the assembly into the steel filter container
(fig. 39), making sure the pin is inserted into the hole
in the support (see arrow in fig. 39).
• Finally, screw on the cap (fig. 40).
Failure to clean as described above invalidates the
guarantee.
CLEANING THE BOILER OUTLET
About every 300 coffees, the espresso boiler outlet must be
cleaned as follows:
- Make sure the appliance is not hot and that it is unplugged
from the mains;
- Using a screwdriver, unscrew the screw fixing the espresso
boiler outlet (fig. 41);
- Clean the boiler with a damp cloth (fig. 25);
- Clean the outlet thoroughly in hot water using a brush.
Make sure the holes are not blocked. If necessary, clean
with a pin.
- Continue to rub the boiler outlet while rinsing under the
tap,
- Replace the boiler outlet.
Failure to clean as described above invalidates the
guarantee.
DESCALING THE ESPRESSO COFFEE UNIT
You are recommended to descale the coffee machine about
every 300 coffees. You should use a commercially available
product specifically for descaling espresso coffee machines. If
you cannot obtain such a product, you can also follow the
procedure below.
1.Fill the espresso coffee water tank with 1 litre of
water.
2.Dissolve 2 spoonfuls (about 30 grams) of citric acid
(obtainable from chemist's or drug stores);
3.Rotate the selector knob to the position and wait
until the OK indicator light comes on.
4.Make sure the filter holder is not attached and
position a recipient under the outlet.
5.Rotate the selector knob to the position (fig. 17)
and run off half the solution in the tank. Then
interrupt the flow by rotating the selector to the "O"
position (fig. 23).
6.Leave the solution to work for about 15 minutes, then
run off the rest of the water in the tank.
7.To eliminate residues of the solution and scale, rinse
the tank well, fill with clean water and replace in its
housing.
8.Rotate the selector knob to the position and run off
the water until the tank is completely empty;
9.Rotate the selector knob to the position and
17
