481718
54
Verklein
Vergroot
Pagina terug
1/76
Pagina verder
53
De Dietrich Gas 310/610 ECO
13.1.2 Pump run on time ()
Pump run on time can be adjusted (Please refer to
installation contractor)
-Press the
-key until the digit (with dot) appears in the
code-display.
-Press the
-key until the digit (with dot) appears in
the code-display.
-Set the required value, using the [+] and [-]-keys.
Press the
-key to stare the new value (value will flash twice).
Press the reset-key to return to operating mode.
Table 18 Adjustments pump run on time
13.1.3 Boiler control ()
Setting mode, parameter , can be set to different values
(see table 19).
Proceed as follows to change the boiler control:
Press the
key until the number (with dot)
appears in the code window.
Press the
key until the letter (with dot)
appears in the code window.
Use the [+] and/or [-] keys to specify the required
setting.
Press the
key to stare the new setting (flashes twice to confirm).
Press the reset key once to return to operating mode.
Table 19 Boiler control settings.
Example: boiler control
indicates that the boiler is controlled by means of a 0-10 volt signal modulated on the
basis of flow temperature (
= 4). Heat demand is on ( = 1).
13.2 Setting mode service level (only for the qualified service engineer) ()
To prevent accidental, unauthorized access by non-qualified persons the control system requires an input code to
gain access to the second level of boiler control.
-Press the
and keys simultaneously and hold. The code-display now shows a letter with a random
number in the
-display.
-While holding both keys pressed, set the
-display to , using the [+] or [-] keys and press the key.
-The display will flash twice, confirming acceptance of the access code.
-Release the keys and
 will disappear from the display.
Important!! Changing the pre-set values without reference to the tables contained in this manual may result
in incorrect boiler operation.
The service settings can now be reached by pressing the -key until the digit (with dot) appears in the
code-display. Set the required value, using the
key.
To deletes the service code, press the reset-key once.
If no keys are pressed over a 15 minute period, the service code will delete automatically.
Code

Description

Pump post purge = 10 seconds

Pump purge time for 1 to 15 minutes
( =  to )

Continuous pump operation
Code

Description


heat demand off

Heat demand on

on/off and High/Low

on/off and modulated on flow temperature

External 0-10v analog signal on temperature
External 0-10v analog signal on output %
54

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw De Dietrich Gas 610 ECO bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van De Dietrich Gas 610 ECO in de taal/talen: Engels als bijlage per email.

De handleiding is 3,76 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info