657633
24
Verklein
Vergroot
Pagina terug
1/40
Pagina verder
This appliance is fitted with a TTB
The TTB is a flue spillage sensor that reacts to flue gasses
flowing past the baffle in the heater back into the living
room.
In the event of a flue spillage, the thermocouple is
interrupted by the TTB, shutting off the gas supply to the
burners.
This protective device will prevent flue gasses from flowing
into the home for any length of time.The device will reset
itself after a few minutes and the heater can then be
reignited.
Possible causes of the TTB being activated
include:
There is little or no supply of fresh air into the home (all
draughts have been excluded and ventilation openings
sealed off).
The outlet into the flue duct is partially or completely
blocked.
The chimney mouth was not constructed correctly, can
cause "fall winds" in the chimney duct being a possible
result.
Measures to prevent TTB activation
The heater can be reignited once the TTB has cooled
down.
If the safety device is activated again, open a window or
some other means of ventilation.
If this resolves the problem, it means that the home is
hermetically sealed and the heater is unable to discharge
all the combustion fumes through the chimney. Some
means of ventilation must be kept open or constructed. If
the safety device is still activated after that, examine the
other possible causes listed above and resolve accordingly.
The safety device may never be disconnected.
The TTB
The TTB safety device has several special components that
should also be incorporated in a replacement TTB.You are
strongly advised not to fit a "standard" thermocouple.
INSTRUCTIONS FOR USE
Type EUROSIT
The EUROSIT gas control block has the following controls:
*
rotary switch with the following settings (1):
• off ( )
• ignition and pilot light ( )
• thermostat
*
push button (2) to operate the piezo ( )
*
manual control (3) for the following settings:
• on full
Adjustable between the maximum and minimum
setting of the manually operated gas tap.
• off
Operating
To ignite the pilot light turn the switch (1) to ( ) and
press fully.Turn button (2) a few times as necessary. Once
the pilot light is ignited, keep pressing the button for
approx. 10 seconds. If you release the button the pilot light
should stay alight, if not, repeat the stages above, pressing
the button for a little longer. If the thermostat has been
set to a temperature higher than the room temperature,
the main burner will ignite when the button is released.
The required temperature can be set using the thermostat
button (1).
NB:
Should the thermostat demand heat it will have priority
over any manually controlled setting.
If the heater is only to be controlled manually, turn the
thermostat to the lowest setting.
If the thermostat is set to ( ), only the pilot light will
burn. Neither the thermostatic tap nor the manually
operated tap will work.
Switching off
To s witch the heater off, turn the switch (1) to . This
will switch both the main burner and the pilot light off.
Switched to the pilot light setting ( ) only the pilot light
will stay alight.
If the heater has been switched off, wait for 5 minutes
before relighting.
INSTRUCTIONS FOR INSTALLATION INSTRUCTIONS FOR USE
20
24

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DRU Maestro bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DRU Maestro in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 1 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info