569915
117
Verklein
Vergroot
Pagina terug
1/122
Pagina verder
117
Code Description Processing
E01
Communication error. The control board and
computer are not communicating correctly.
The machine stops and goes into fault status, computer shows “E1”, and the alarm beeps three times.
Possible causes: check all the connection points between the console and controller. Make sure all plugs
are well connected. Check all the wires for damage. If this fails, change the connector wires.
E02
Erratic motor cable connection
Start and stop fault status. The computer beeps 9 times and shows “E2”. Treadmill goes into the ready
mode and restarts. Possible causes: low power or voltage, or faulty controller. Check all motor wires for
correct connection.
E03
Speed sensor error.
Stops and go into fault status. Computer shows “E03”. Other areas show blank. After 10 seconds the
machine will go into ready mode, and can be restarted.
Possible causes: the computer is not receiving motor speed sensor feedback for more than 3 seconds:
check sensor plug and motor connection wires. Check the controller.
E04
Incline motor error
Check if incline motor sensor wire and AC wire are well connected. After checking press the button on
controller to reset the incline motor adjustment.
E05
Over-current protection.
Stops and goes into fault status, computer shows “E05”. Other areas show blank. After 10 seconds the
machine will go into ready mode, and can be restarted.
Possible causes: system encounters overvoltage and goes to self-preservation. Moving parts may be
blocked. Check and adjust the machine and restart. Check motor or controller for burning smell. If so,
change motor and/or controller. Check whether the power voltage is too low or not to the standard and
retest with the correct voltage.
E06
Controller self-check error.
Computer shows "E06". Possible causes: the controller wires are not connected well, check and
reconnect or change. After checking press the button on controller to reset the system.
E07
EPROM (Data memory error)
Computer shows“E08”. Possible causes: the controller wires are not connected well, check and
reconnect or change EPROM IC.
117

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

DKN-Ecorun

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw DKN Ecorun bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van DKN Ecorun in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 7,75 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info