Handleiding Curtis G4TPX2 (pagina 34 van 37) (Engels)

690874

Verklein

Vergroot

Pagina terug

1/37

Pagina verder

TROUBLESHOOTING GUIDE TG7

G4 BREWERS WITH SSR, TROUBLESHOOTING GUIDE 122717A

Water Does Not Heat At All

• Check to see if the water level in the tank is in contact with the water level probe. If not, see Tank Does Not Fill.

The water will not heat unless it is in contact with the probe.

• If the water heats, but is not hot enough, see Water Not Hot Enough.

• If Ready to brew appears on the display, but the water is not hot, check the resistance across the leads of the

temperature sensor. If the resistance is less than 10 k and the water is not hot, replace the temperature sensor.

If the sensor resistance is above 10 k when the water is cool, replace the universal power module (UPM).

If Heating... appears on the display, but the water is not hot, follow the steps below. The following steps are

performed with the rear toggle switch in the ON position.

1 Check for power across the terminals of the heating element(s). If power is being supplied, remove the wires

and check for an open heating element.

2 If there is no power to the element(s), trace the circuit back (using the ELECTRICAL SCHEMATIC) to the power

DPSEUPmOEPVUXIFSFQPXFSJTMPTU*GUIFSFJTQPXFSJOUPUIFTPMJETUBUFSFMBZT443TCVUOPUPVUTFFUIF

following step. On units having two SSRs, be sure to check both.

3 If there is power into a SSR, but not out, check for 5 Vdc (nominal*) across the + and - pins of the SSR(s). If

there is 5 Vdc across the + and - pins of the SSR(s), but no (or low) output voltage at a SSR output terminal,

replace the SSR. If 5 Vdc is not being supplied from the UPM, but Heating... appears on the display, check

the wiring from the UPM to the SSR(s). If the wiring is OK, replace the UPM.

Water Too Hot (Boiling or Excessive Steaming)

1 If Over Temp Sensor or Ready to Brew appears on the display and the water is too hot, go to Over Temp

Sensor Error Message.

2 If the display reads HeatingDPOTUBOUMZmSTUDIFDLUPNBLFTVSFUIBUUIFUFNQFSBUVSFTFOTPSJTBUUBDIFEUJHIUMZ

to the tank and that heat sink compound was used. A properly mounted sensor should have a resistance of

around 7 k when the water is hot. If not, replace the sensor.

3 Check to see if the universal power module (UPM) constantly has +5 Vdc (nominal) output to the solid state

relay (SSR), regardless of the resistance of the temperature sensor. If so, the UPM is probably bad.

4 If the UPM is working properly, check for a shorted SSR.

Over Temp Sensor Error Message

This error message indicates that the universal control module (UCM) has detected a water overheating

problem. The universal power module (UPM) is reading a water temperature in the tank above 210ºF. If the water

temperature is too hot, but Heating... appears on the display, see Water Too Hot. Once the malfunction causing

the error is corrected, the error message must be cleared. To reset the brewer and return to normal operation, turn

the toggle switch on the back of the brewer to the OFF position for 5 seconds, then back on.

1 Check for 5 Vdc (nominal) across the + and - pins of the solid state relay (SSRs). If no power is applied to the

SSR and the heating elements are always on, replace the SSR. On units having two SSRs, check both.

2 Turn off power to the brewer and allow the water tank to cool. Once cool, turn power back on while monitoring

the voltage across the + and - pins of the SSR(s). During normal operation, the voltage should be 5 Vdc,

until the water is hot, then drop to below 1 Vdc. The universal power module (UPM) should be replaced if the

voltage reads 5 Vdc constantly even though Ready to brew or Over Temp Sensor appears on the display.

3 If the UPM is operating normally, check for a false over-temp error caused by the temperature sensor. Check

the resistance across the leads of the temperature sensor. If the resistance is less than 10 k when the water is

cool, replace the temperature sensor.

IMPORTANT: Before proceeding, make sure that the control panel temperature is adjusted to compensate

for higher elevations. The factory setting is 200°F. Reduce the temperature setting two degrees for every

1000 feet of elevation above 4000 feet.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Curtis G4TPX2 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info