810366
356
Verklein
Vergroot
Pagina terug
1/396
Pagina verder
354
Wheels and tyres
Shake the tyre sealant bottle vigorously
›››Fig.230 10 .
Screw the tyre ination hose ›››Fig.230 3
into the tyre sealant bottle. The bottle's seal
will break automatically.
Remove the ller cap ›››Fig.230 3 and
screw the open end of the tube into the tyre
valve.
With the bottle upside down, empty all of
the contents into the tyre.
Remove the bottle from the valve.
Replace the howitzer with the device
›››Fig.230 1 onto the tyre valve.
Inating the tyre
Screw the tyre ination tube of the compres-
sor ›››Fig.230 8 on the tyre valve.
Check that the air evacuation screw is
closed ›››Fig.230 6 .
Start the engine and leave it running.
Attach the connector ›››Fig.230 9 to the
vehicle’s 12 volt power outlet ›››page235.
Switch on the air compressor with ON/OFF
switch ›››Fig.230 5 .
Keep the air compressor running until it
reaches a pressure of 2.0-2.5 bar (29-36psi/
200-250kPa). A maximum of 8 minutes.
Disconnect the air compressor.
If it does not reach the pressure indicated,
unscrew the tyre inator tube from the valve.
Move the vehicle 10m so that the sealant is
distributed throughout the tyre.
Screw the compressor tyre inator into the
valve.
Repeat the ination process.
If it still does not come up to pressure, the
tyre is too badly damaged. Stop and seek assis-
tance from authorised personnel.
Disconnect the air compressor. Unscrew the
tyre ination tube from the tyre valve.
When the tyre pressure is between 2.5 and
2.0 bars, continue driving without exceeding
80km/h (50 mph).
Attach the sticker ›››Fig.230 2 to the in-
strument panel display, within the driver's eld
of vision.
Check the pressure again after 10minutes
›››page354.
WARNING
When inating the wheel, the air compressor
and the inator tube may become hot.
Protect hands and skin from hot parts.
Do not place the hot exible inator tube
or hot air compressor on ammable material.
Allow them to cool before storing the de-
vice.
If it is not possible to inate the tyre to at
least 2.0bars (29psi / 200kPa), the tyre is
too badly damaged. The sealant is not in a
good condition to seal the tyre. Do not con-
tinue driving. Seek specialist assistance.
NOTICE
Switch o the air compressor after a maxi-
mum of 8 operational minutes to avoid over-
heating! Before switching on the air com-
pressor again, let it cool for several minutes.
Check after 10 minutes of driving
Screw in the inator tube ›››Fig.230 8 again
and check the pressure on the gauge 7.
1.3bar (19psi / 130kPa) and lower:
Stop the vehicle! The tyre cannot be sealed
suiciently with the tyre mobility set.
You should obtain professional assistance
››› .
1.4 bar (20 psi/140 kPa) and higher:
Set the tyre pressure to the correct value
again.
Carefully resume your journey until you
reach the nearest specialised workshop with-
out exceeding 80km/h (50mph).
Have the damaged tyre replaced.
356

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Cupra Formentor - 2022 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Cupra Formentor - 2022 in de taal/talen: Engels als bijlage per email.

De handleiding is 7.81 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Cupra Formentor - 2022

Cupra Formentor - 2022 Gebruiksaanwijzing - Nederlands - 424 pagina's

Cupra Formentor - 2022 Gebruiksaanwijzing - Deutsch - 415 pagina's

Cupra Formentor - 2022 Gebruiksaanwijzing - Français - 436 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info