534695
28
Verklein
Vergroot
Pagina terug
1/37
Pagina verder
REMOVING SUPPORTS WITH THE ULTRASONIC SUPPORT REMOVAL TANK (sold separately)
HOT WATER METHOD
Caustic soda can burn if handled improperly. Never handle caustic soda without using all of the supplied
Personal Protective Equipment (PPE): gloves, goggles and tongs. If caustic soda touches the skin, wash it away
immediately. If caustic soda touches the eyes, immediately use an eyewash treatment.
Never operate the unit without water in the cleaning tank. Damage may occur.
Never use boiling water. Damage may occur.
This process uses hot water (approximately 80°C). Wear all Personal Protective Equipment (PPE).
Do not operate without water in the cleaning tank. Damage may occur.
Never use boiling water. Damage may occur.
!
!
The Ultrasonic Support Removal Tank automatically removes PLA support material from ABS models. The tank uses one of
two methods to remove or weaken the material:
Use caustic soda solution in the Ultrasonic Support Removal tank for 3 hours to dissolve the PLA material.
Weakening the PLA material for manual removal by lightly scraping or by hot water soak for 48 hours
1. Position the unit on a at and stable work surface. Do not knock or move the tank during operation. This risks splashing
water onto electrical components.
2. Pour 0.75 liters of water into the tank.
3. Place the models to be cleaned in the tank.
4. Close the lid, connect the power supply and press the power button to turn on the tank.
5. Use the -5 and +5 buttons to set the temperature. For best results, set the temperature to 80°C.
6. Set an alarm for 48 hours. Do not use the timer on the tank when using the hot water method. This is intended for the
ultrasonic operation used with the caustic soda method and will only run for 180 minutes.
7. After 48 hours, remove your model from the tank using the provided plastic tongs and immediately run under cold water
for 1-2 minutes.
8. Make sure you turned off the Ultrasonic Support Removal Tank.
9. After the model has been washed, the PLA support material should crumble away easily. You can use a blunt knife to
scrape the support away from the model. Additional rinsing may help ush remaining support material fragments from
the model.
METHOD ADVANTAGES DISADVANTAGES
Hot water Avoid use of corrosive chemicals Support material requires slight physical
force to crumble away.
Support material in hidden cavities may
remain if user is unable to reach them.
Process is relatively extended.
Caustic soda Quick removal.
Support material in hidden cavities will be
dissolved without physical force, provided
the solution can reach the cavity
Requires health and safety procedures.
27
28

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Cubify CubeX bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Cubify CubeX in de taal/talen: Engels als bijlage per email.

De handleiding is 4,56 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info