772513
18
Verklein
Vergroot
Pagina terug
1/40
Pagina verder
16 CroozerDog20-ENG-11-19
Converting the Croozer Dog to a Bicycle Trailer
Installing the axle hitch to a bicycle with a quick-
release axle
The quick-release lever (1) must be positioned on the right
side of the bicycle (relative to the direction of travel). If the
lever is on the left side, the quick-release skewer must be
removed and reinserted from the right side. Be sure to fol-
low the applicable instructions in the owner’s manual of the
bicycle and/or consult a professional bicycle mechanic.
1. Open the quick-release lever (1) on the rear wheel
of the towing bicycle or loosen the Allen bolt (5 mm),
depending on the type of quick-release skewer. Often,
the open position is indicated on the lever by the word
“OPEN”. In this case, when the word “OPEN” can be
seen, the lever is in the open position.
2. Remove the tension-adjusting nut (2) of the quick-
release assembly by turning the nut anticlockwise.
Use caution: the spring located just beneath the nut is
under tension and could y off when removing the nut.
3. Fit the axle hitch (3) over the end of the quick-release
skewer by sliding the skewer (with the spring) through
the hole in the hitch.
4. Thread the tension-adjusting nut (2) back onto the
skewer, turning it clockwise at least ve full turns.
The tension-adjusting nut must engage the threads of the
skewer for at least five full turns in order to ensure adequate
clamping force for holding the rear wheel securely. Failure
to tighten the tension-adjusting nut adequately may result
in accidents with serious injury or death. If the quick-release
skewer is too short, it must be replaced. Consult a profession-
al bicycle mechanic for the appropriate parts and assistance.
5. Check that the rear wheel is properly aligned, adjusting
the position if necessary; then close the quick-release
lever (1) or tighten the hex bolt, depending on the ver-
sion. Often, the closed position is indicated on the lever
by the word “CLOSE”. In this case, when the lever side
marked “CLOSE” can be seen, the lever is in the closed
position. If the axle nut has been tightened the proper
amount, you will be able to feel the resistance increase
when the lever is about halfway closed, i.e. parallel to
the axle. The adjustment is correct if you can fully close
the lever but with considerable force. In the closed
position, the lever should be parallel to the frame, i.e. it
should not stick out to the side.
6. Check whether the quick-release skewer is securely
engaged by trying to rotate the quick-release skewer
without opening the lever.
If the quick-release skewer is loose enough to rotate,
then the clamping force is inadequate. In this case,
open the lever, and tighten the tension-adjusting nut
half a turn clockwise. Repeat steps 5 and 6.
If it is impossible to push the quick-release lever into
the closed position, then open the lever, and unscrew
the tension-adjusting nut half a turn anticlockwise.
Repeat steps 5 and 6. Keep in mind that the tension-
adjusting nut must engage the threads of the quick-
release skewer for at least ve full turns.
The tension-adjusting nut must engage the threads for at
least five full turns in order to ensure adequate clamp-
ing force for holding the rear wheel securely. Failure to
1
2
3
2
3
min. 5 x
1
18

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Croozer Dog - 2020 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Croozer Dog - 2020 in de taal/talen: Engels als bijlage per email.

De handleiding is 5.75 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Croozer Dog - 2020

Croozer Dog - 2020 Gebruiksaanwijzing - Nederlands - 40 pagina's

Croozer Dog - 2020 Gebruiksaanwijzing - Deutsch - 40 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info