736874
14
Verklein
Vergroot
Pagina terug
1/54
Pagina verder
16
Monitoring the operating pressure
IMPORTANT!
The PVC material will stretch a little
following initial inflation and will never
return to its original size.
Please remember that this data can
vary slightly, depending on the cargo it
is carrying and the outside
temperature.
Pump up the air chambers
/ / so that they
feel firm to the touch and no wrinkles can be
seen in the material. Press on each air chamber
with your thumb; you should just about be able
to press the material in slightly.
Measuring strips and monitoring
ruler (Fig. H, I)
To monitor the air chamber / operating
pressure, place the 0 of the monitoring ruler
(Fig. I) over the 0 of the measuring strip
(Fig. H) on the article.
During initial inflation, the maximum stretch point
MUST NOT exceed Position A on the monitoring
ruler.
From the second use onwards, pump up the craft
so that the 10 on the measuring strip is between
Position A and Position 10 of the monitoring
ruler.
Inflating the air chambers
Floor chamber with stopper
valve
/ Lower side chamber with stopper
valve (Fig. J)
1. Open the valve closure
.
2. Pump up each air chamber.
3. Close the valve closure and press the sealed
valve down using a little pressure.
/ Upper side chamber with screw
valve (Fig. F)
1. Inflate the upper side chambers / and
seal the closure cap by screwing in a
clockwise direction.
Front seat, Rear splash guard
with seat, Prow splash guard,
Triangular cushion (Fig. K - N)
Note:
The ropes must be tied using a reef
knot and a figure-of-eight hitch knot
(Fig. K, L)
1. Front seat (Fig. M, N)
Pump up all of the air chambers. Place the seat
underneath both of the upper side air chambers
/ , so that the seat is securely fitted. Tie the
seat using the 80cm rope through the eyelet on
the floor chamber (Fig. M) as well as with
a 150cm rope in a zig-zag shape through the
eyelets on the side chambers and (Fig. N).
2. Rear splash guard with seat
Pump up all of the air chambers. Press the seat
underneath both of the upper side air chambers
/ , so that the seat is securely fitted.
Fasten the rear splash guard with seat with a
280cm rope in a zig-zag shape through the
eyelets on the side chambers and .
3. Prow splash guard
Pump up all of the air chambers and fasten the
prow splash guard with a 280cm rope in a zig-
zag shape to the eyelets on the side chambers
and .
4. Triangular cushion
Position the inflated triangle cushion securely in
the bows of the kayak, where it serves as a foot
support for the person sitting at the front.
Dismantling the kayak
Remove the front seat, the rear splash guard with
seat, the prow splash guard and the triangular
cushion.
Deflating
Deflate the kayak as follows:
1. To deflate the floor chamber
, the lower side
chambers / , the front seat , the rear
splash guard with seat , and the prow
splash guard , pull the stopper valve out
of its concealed location and press the shaft
lightly or use the deflation tube .
GB/IE
14

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Crivit Inshore 335 V IAN 282780 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Crivit Inshore 335 V IAN 282780 in de taal/talen: Nederlands, Duits, Engels, Frans, Portugees, Spaans als bijlage per email.

De handleiding is 3,67 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info