Handleiding Crivit IAN 355244 (pagina 17 van 46) (Nederlands, Duits, Engels, Frans, Pools)

744148

Verklein

Vergroot

Pagina terug

1/46

Pagina verder

Step 2 (Fig. C)

1. Screw the right pedal (9) clockwise onto the

crank.

Note: observe the marking (R) and direction of

rotation for the right pedal.

2. Screw the left pedal (8) anti-clockwise onto

the crank.

Note: observe the marking (L) and direction of

rotation for the left pedal.

3. Fasten the straps (10) onto the pedals (8)/(9).

Note: the straps on the pedals must be able to

keep your feet ﬁrmly secured. If the straps feel

uncomfortably tight, loosen them.

Step 3 (Fig. D)

1. Insert the seat post (4) into the back opening

of the base frame (1).

2. Fasten the seat post with the setting screw

(4a).

Step 4 (Fig. E)

1. Hold the steering column (5) against the

front opening of the base frame (1).

2. Push the steering column cover (12) just over

the steering column (5).

3. Set the resistance controller (5c) to the high-

est level of resistance (level 8).

4. Insert the end of the draw cable (5a) into

the end of the draw cable (1a).

Note: make sure that the draw cables are ﬁrmly

connected.

5. Set the resistance controller (5c) to the low-

est level of resistance (level 1).

Note: this tightens the draw cable (5a).

6. Remove the plastic cover (5f).

7. Connect the sensor cable (5b) to the sensor

cable (1b).

Note: make sure that both sensor cables are

ﬁrmly connected, otherwise there will be no sig-

nal transmission.

8. Place the steering column (5) onto the base

frame (1).

Note: make sure that the sensor cable and

draw cable are within the frame.

9. Screw the steering column (5) onto the base

frame (1) with the screws (5d) and the wash-

ers (5e).

10. Push the steering column cover (12) over the

screws (5d) to cover them.

Step 5 (Fig. F)

1. To assemble the handlebars (6), ﬁrst guide

the sensor cable (6a) up through the bottom

opening of the steering column (5).

Note: pull the cable out from the steering col-

umn somewhat.

2. Open the holding clamp (5g) and place the

handlebars (6) into the holding clamp.

3. Close the holding clamp (5g) and place the

steering column cover (15) over it.

4. Fasten the handlebars (6) and the steering

column cover (15) with a lock washer (18),

a washer (21) and the T-handle screw (22).

Step 6 (Fig. G)

1. Hold the computer (7) against the steering

column and connect the sensor cables (6a)

from the steering column with the sensor ca-

bles (7b) from the computer.

Note: the sensor cables are labelled PULSE

and SENSOR for better recognition. Connect the

PULSE sensor cables. Make sure that the sensor

cables are ﬁrmly connected.

2. Connect the sensor cable (7a) with the sen-

sor cable (5h).

Note: the sensor cables are labelled PULSE

and SENSOR for better recognition. Connect

the SENSOR sensor cables. Make sure that the

sensor cables are ﬁrmly connected.

3. Insert the sensor cables into the steering

column (5).

4. Remove the screws (7c) on the back of the

computer (7), place the computer on the

steering column (5) and reattach the screws

(7c).

Note: make sure that you do not clamp the

sensor cables.

Step 7 (Fig. H)

1. Place the left computer cover (13) and right

computer cover (14) on the sides of the

steering column (5) and fasten them both

with the pre-mounted screws (5i).

Step 8 (Fig. I)

1. Fasten the seat (11) to the seat adjustment

track and align the seat horizontally.

2. Remove the pre-mounted screws (5i) from

the steering column (5).

3. Fasten the water bottle holder (16) to the

steering column (5) with the previously re-

moved screws (5i).

Note: use of the water bottle holder is optional.

Disassembly

Proceed in the reverse order to disassemble the

product.

Use

• Choose a training area of approx.

3.00 x 1.80m (L x W).

• Train on a ﬂat, non-slip surface only.

Inserting and replacing the batter-

ies (Fig. J)

WARNING! Observe the following

instructions to avoid mechanical and

electrical damage to the product.

The product comes with two batteries (26)

that can be removed from the packaging and

inserted into the computer (7) before using it for

the ﬁrst time.

When the batteries (26) are ﬂat, you can

replace them.

1. Open the battery compartment cover (7d).

2. Insert the batteries (26) in the battery com-

partment.

Note: pay attention to the plus/minus poles of

the batteries and to their correct insertion. The

batteries must be completely inside the battery

holder.

3. Close the battery compartment cover (7d).

4. Follow the insertion instructions when

replacing the batteries. First remove the flat

batteries from the battery compartment.

Setting the seat, foot and handlebar

position (Fig. L)

• Set the seat position so that your leg is

outstretched when your heel is touching the

pedal and your knee is behind the pedal

axle. Use the adjusting screw (4a) to set the

height, and the adjusting screw (4b) below

the seat to bring it to the correct distance.

• Position your feet in the centre of the ped-

als. When training with the product, the

movement comes from the balls of your feet

so that you have better leverage and your

movements are easier.

• Make sure that at least half the length of

your foot is on the pedal during training.

• Tighten the safety straps on the pedals to

ensure that your feet have a good grip.

• Use the T-handle screw (22) to adjust the

handlebars so that your arms are fully out-

stretched when holding the handlebars.

• Use the resistance controller (5c) to set the

pedal resistance suitable for you and your

workout.

Using the smartphone or tablet

holder

1. Place your smartphone or tablet on the

smartphone or tablet holder.

2. Fasten your smartphone or tablet with the

clip (7e) (Fig. K).

Operating the computer

Turning on the computer

1. Insert the batteries into the computer as de-

scribed in the section ‘Inserting and replac-

ing the batteries’.

2. Press any button or use the pedals. The com-

puter turns on automatically.

Setting up the computer

The calendar function is displayed when using

the computer for the first time.

1. Set the desired date with the buttons (7m,

7o).

Note: you lower the input with the button (7m)

and increase the input with the button (7o).

2. Confirm your respective input with ‘ENTER’

(7p) to switch between days, months and

years.

Note: press the ‘ENTER’ button to confirm the

input. You are automatically directed to the nor-

mal display view.

Changing the language

You have the option of changing the computer

language. English is the pre-set default lan-

guage. Proceed as follows to change the com-

puter language to German:

1. Press the ‘RESET’ and ‘ENTER’ buttons simul-

taneously.

Note: the display is reset and the calendar

function is displayed.

2. Set up the computer as described in the sec-

tion ‘Setting up the computer’.

Note: the normal display view appears and the

computer language is now German.

3. Repeat the steps to change the computer

language back to English.

Display view (Fig. K)

The following information and functions are

shown on the display:

• Current speed from 0.0 to 99.9km/h is dis-

played (7g).

• A training duration with pause mode of be-

tween 00:00 and 99:59 is displayed (7h).

• The distance pedalled from 0.0 to 99.9km is

displayed (7i).

• Energy burn* of 0 to 9,999 kilojoules is

displayed (7j).

GB/IE

Crivit IAN 355244 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info