818989
6
Verklein
Vergroot
Pagina terug
1/191
Pagina verder
5 MAINTENANCE
IMPORTANT
Read and understand the safety regulations and the
maintenance instructions before you clean, repair or do the
maintenance work on the machine.
IMPORTANT
Make sure that all nuts, bolts and screws are tight. Check
regularly that the handles are firmly mounted.
IMPORTANT
Use only the replacement parts and accessories of the initial
manufacturer.
5.1 GENERAL INFORMATION
IMPORTANT
Only your dealer or approved service center can do the
maintenance that is not given in this manual.
Before the maintenance operations:
Stop the machine.
Remove the battery pack.
Cool the motor.
Store the machine in a cool and dry place.
Use correct clothing, protective gloves and safety glasses.
5.2 CLEAN THE MACHINE
Clean the machine after each use with a moist cloth
dipped in neutral detergent.
Do not use aggressive detergents or solvents like "glass
cleaner" to clean the plastic parts or handles.
Keep the trimmer head free from grass, leaves, or
excessive grease.
Keep the air vents clean and free of debris to avoid
overheating and damage of the motor.
Do not spray water onto the motor and electrical
components.
5.3 REMOVE THE REMAINING LINE
Figure 9 - 11.
1. Simultaneously press the tabs on the sides of the trimmer
head.
2. Pull and remove the spool cover.
3. Remove any remaining line.
4. Clean dirt and debris from all parts.
5. Align the spool tabs with the tab openings in the base of
the spool.
6. Push the spool cover until it clicks into position.
5.4 INSTALL THE CUTTING LINE
Figure 12 - 15.
NOTE
Do not put more than 15 feet of cutting line in at a time.
1. Line up the slots on the spool cap with the slots on the
trimmer head.
2. Put the cutting line through the hole. Push the cutting line
until it exits the opposite hole.
3. Pull the cutting line through until there is an equal
quantity of cutting line on each side.
4. Turn the spool cap clock-wise to wind the cutting line
into the trimmer head. Keep approximately 5 in of cutting
line above out of each side of the trimmer head.
5.5 REMOVE THE TRIMMER HEAD
Figure 16.
1. Put the metal rod in the specified angle transmission hole
to fix the trimmer head.
2. Turn the trimmer head clockwise to loosen it. Do not
remove the spacer from the shaft.
5.6 ASSEMBLE THE TRIMMER HEAD
Figure 16.
1. Put the metal rod in the specified angle transmission hole
to fix the trimmer head.
2. Assemble the trimmer head.
3. Turn the trimmer head counterclockwise to tighten it.
4. Remove the metal rod.
IMPORTANT
You must install the cut-off blade when you use the trimmer
head.
6 TRANSPORTATION AND
STORAGE
6.1 MOVE THE MACHINE
When you move the machine, you must:
Wear gloves.
Stop the machine.
Remove the battery pack and charge it.
Assemble the blade guard.
6.2 STORE THE MACHINE
Remove the battery pack from the machine.
Make sure that children cannot access the machine.
Keep the machine away from corrosive agents such as
garden chemicals and de-icing salts.
6
English
EN
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Cramer 82T15 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Cramer 82T15 in de taal/talen: Alle talen als bijlage per email.

De handleiding is 3.69 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info