652338
63
Verklein
Vergroot
Pagina terug
1/80
Pagina verder
63Mounting and installation work
5.7.6 Installation work external connections
Connecting the external safety chain
B3
B2
B1
MAINS SUPPLY
L N SC1SC2PEPE
J3
K2
Control compartment
Do not apply extraneous
voltage via K2!
DANGER: 230 V
The potential-free contacts of external moni t or ing de-
vices (e.g. ventilation interlock "B1", airow monitor "B2",
safety high limit humidistat "B3", etc.) are connected in
series (safety chain "K2") to the terminals "SC1" and
"SC2" of the terminal block "X1" on the driver board in
accordance with the wiring diagram.
The connecting cable must be led through a cable gland
into the control compartment.
Caution! A high limit humidistat is highly recomen-
ded to prevent risk of over-humidication and potential
damage to property.
Note: If, for whatever reason, no external monitoring de-
vices are connected, a jumper wire "J3" must be installed
on the contacts "SC1" and "SC2" of the terminal block.
CAUTION! Do not apply any extraneous voltage to
contacts "SC1" and "SC2" via the contacts of the
external monitoring devices.
Humidity control wiring
Connecting a demand or humidity signal
CONTROL
V+ IN GND
JP2 (24V)
JP1 (10V)
+
A1
Y
24V/
10V
Control compartment
The signal cable of an external controller or of a humid-
ity sensor (if the internal P/PI controller is used) are to
be connected according to the wiring diagram to the
terminals "IN" and GND" on the driver board in the
control compartment. The connecting cable must be
led through a cable gland into the control compartment.
Note: if the external controller or the humidity sensor
shall be supplied with 10 V or 24 V from the driver board
(terminal “A+”), the jumper JP1 must be set to 10V or
24V accordingly.
Note: the humidity control must be congured via the
control software accordingly. The admissible humidity
control signal values can be found in the technical data
table in the operation manual.
If a shielded signal cable is used, connect the shielding
to terminal "GND".
Caution! If the shielding of the control signal is already
connected to a po ten tial or a grounded conductor,
do not connect it to terminal "GND"
63

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Condair RS bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Condair RS in de taal/talen: Engels als bijlage per email.

De handleiding is 7,04 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Condair RS

Condair RS Gebruiksaanwijzing - Nederlands - 80 pagina's

Condair RS Installatiehandleiding - Nederlands - 76 pagina's

Condair RS Gebruiksaanwijzing - English - 80 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info