738048
19
Verklein
Vergroot
Pagina terug
1/38
Pagina verder
19
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
•Reorientorrelocatethereceivingantenna.
•Increasetheseparationbetweentheequipmentandthereceiver.
•Connecttheequipmentintoanoutletonacircuitdifferentfromthattowhichthereceiverisconnected.
•Consultthedealeroranexperiencedradio/TVtechnicianforhelp.
LEVEL III. extra functions (for advanced users)
All of the PM2 buttons except the ON/OFF button have extra functions which are activated when you press and
hold down the READY button.
These special functions include:
• Two Odometers: one is resettable (trip odometer) and one is not resettable
• Split Intervals: you can set the PM2 to measure splits at intervals which you set. Each split will be saved for
recall after you finish and can be displayed for 6 seconds while you row.
• Drag Factor: you can set the PM2 to display the drag factor which it calculates during the rundown of the
flywheel.
• PM2 Display Test
BUTTON SEQUENCES & DESCRIPTIONS OF EXTRA FUNCTIONS:
RECALL
ON/OFF DISPLAY
SET DIGITS
REST
READY
TIME METERS
OK
/500 m
WATT
CAL
Hold
down
Custom Splits (distance)
to have splits displayed during
your workout. Repeating this
button sequence will turn off the
split display during your workout.
When the PM2 powers up, splits
are off by default.
Hold
down
Splits On/Off
to perform a self-test including all
segments test. Press ON/OFF to end
the test.
Hold
down
then
press
READY
DISPLAY
PM2
DISPLAY
TEST
to set a time interval for split
measurement. Use the SET DIGITS
buttons to set the split time. Then
press READY when done. Note:
your custom split interval will not
be retained through a power down.
Default value is 2 minutes.
Hold
down
Custom Splits (time)
SPLITS
READY TIME READY METERS
READY RECALL
then
press
then
press
then
press
to set a distance interval for split
measurement. Use the SET DIGITS
buttons to set the split distance. Then
press READY when done.
Note: your custom split interval will
not be retained through a power
down. Default value is 500 meters.
DRAG
FACTOR Hold
down
to have a drag factor displayed in the lower right display window.
Repeating this button sequence will turn off the drag factor
display. The drag factor is most helpful if you row on Concept2’s
in different locations and want to be sure the resistance setting
is the same. Check the drag factor on your “home” machine,
and then adjust the damper on the “away” machine until you
get the same drag factor. Typical range for drag factor on the
Indoor Rower is: 103 (damper setting 1)-223 (damper setting
10). When PM2 powers up or resets, the drag factor display
will be off by default.
Note: When a heart rate monitor is being worn, HR will override
the drag factor and will always be displayed.
READY REST
then
press
Hold
down
then
press
READY SET DIGITS
Not Resettable
to display cumulative distance
rowed. This odometer is not
resettable. Distance is in kilometers
and is only displayed when READY
and are being pressed.
Hold
down
READY SET DIGITS
Resettable
to display a resettable record of
distance rowed. At 99,999 it rolls over
to 00,000. Press RECALL to reset to
0. Press READY or ON/OFF to get
out of this function.
then
press
TWO ODOMETERS
19

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Concept2 Model C bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Concept2 Model C in de taal/talen: Engels als bijlage per email.

De handleiding is 2,26 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info