634434
22
Verklein
Vergroot
Pagina terug
1/32
Pagina verder
pinching either the saw chain or the guide bar when the second notch is being made.
- Felling back cut: make the felling back cut (Y) at least 50 mm higher than the
horizontal notching cut. Keep the felling back cut parallel to the horizontal notching cut.
Make the felling back cut so enough wood is left to act as a hinge. The hinge wood
keeps the tree from twisting and falling in the wrong direction. Do not cut through the
hinge.
- As the felling gets close to the hinge the tree should begin to fall. If there is any
chance that the tree may not fall in the desired direction or it may rock back and bind
the saw chain, stop cutting before the felling back cut is complete and use wedges of
wood, plastic, or aluminum to open the cut and drop the tree along the desired line of
fall.
- When the tree begins to fall remove the chain saw from the cutting, stop the motor,
put the chain saw down, and then use the retreat path planned. Be alert for overhead
limbs falling and watch your footing.To complete the felling operation, drive a wedge
(Z) into the horizontal cut.
-Beware of falling branches when the tree starts to move.
b. Cutting branches
When using a chainsaw to remove the branches of a tree to the ground, start with the small
branches and those that are not in contact with the ground. Be careful when cutting limbs
under tension as they may be projected too quickly when you suddenly relieve the
tension.
When you cut the branches, the tree could roll. Always have a backup channel open
in the opposite risk to get away quickly sense. Keep the work area clear to avoid treas-
woodshed
Never operate a chainsaw arms outstretched. Do not try to cut hard-to-reach areas or
by standing on a ladder. Never work at a height above the shoulders.
c.Cutting logs and planks
Use a sawhorse or a stable support. Saw still outside of arm sawhorse. The substrate
must be high enough to prevent the tip of the guide bar touching the
ground and the
chain becomes dull.
If the saw gets stuck, stop the
machine and remove it from the socket. Raise the
workpiece and change its position. Never attempt to free the trapped saw by pulling the
handle or the electric cable
Place the saw on one end and put it on at full speed. Advance the saw without force
using the bar spikes as a pivot point. If necessary, reposition the spikes on the timber
to limit the angle of cut.
Note: The diameter of the work piece must not exceed the length of the guide bar
18
22

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Cobra CS35E bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Cobra CS35E in de taal/talen: Engels als bijlage per email.

De handleiding is 4,15 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info