538305
1
Verklein
Vergroot
Pagina terug
1/29
Pagina verder
1
Contents
Features
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
The CB Story. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A1
Licensing/Warning/Included Accessories . . . . . . . A1
Controls and Indicators. . . . . . . . . . . . . . . . . . . . . . . . . A2
Our Thanks to You . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A3
Customer Support . . . . . . . . . . . . . . . . . . . . . . . . . . . A3
Operating Your CB Mobile Radio
Installation/Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Turning On. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
CB Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Microphone Connector. . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Squelch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Setting Squelch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Channel Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Channel 9/19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
CB/Weather . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Dual Watch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Soundtracker System . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Activating Soundtracker System. . . . . . . . . . . . . . . . . . 11
S/RF Power Meter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
RX/TX Indicator LED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Antenna Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
External Speaker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Ignition Noise Interference . . . . . . . . . . . . . . . . . . . . . . . 14
Temporary Mobile Operation. . . . . . . . . . . . . . . . . . . . . 14
Operation to Receive/Transmit . . . . . . . . . . . . . . . . . . . 15
Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Frequency Ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20, 21
Accessories Order Info . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
If You Think You Need Service . . . . . . . . . . Back Cover
Features of This Product
40 CB Radio Channels
10 Weather Channels
Soundtracker
T
M
System
Instant Channel 19 and 9
40 Channel Scan
Dual Watch
Front Firing Speaker
Channel Saver Circuitry
Dynamic Microphone
9 Foot Mic Cord
Front Panel Microphone
Connector
How to Use Your
Cobra 18WXST II
2
Mounting and Connections
Select a location for the transceiver and micro-
phone bracket that is convenient for operation.
In automobiles, the transceiver is usually mounted
to the underneath of the dash panel, with the
microphone bracket beside it.
Hold the radio with mounting bracket in the
exact location desired. Remove the mounting
bracket and use it as a template to mark the
location for the mounting screws.
Drill necessary holes and secure mounting
bracket in location.
Connect the antenna cable plug to the recepta-
cle marked ANT on the back of the unit.
Mounting and
Connections
Note
The transceiver is held in the
universal mounting bracket by
two thumb screws, permitting
adjustment at the most conve-
nient angle.
A universal mounting bracket
is supplied along with self tap-
ping screws and star washers.
To mount the transceiver:
OperationInstallation
CB Tranceiver
EXT. SPKR.
POWER
13.8V DC
ANTENNA
CB Transceiver
3
Connect the red lead of DC power cord to an
accessory 12 volt fuse.
Connect the orange lead to a constant 12v fuse
(ie: cigarette lighter or direct to battery)
Connect the black lead to the negative side of
the automobile.This is usually the chassis. Any
convenient location with good electrical contact
(remove paint) may be used.
Mount the microphone bracket on right side of
the transceiver or near it using two screws sup-
plied.When mounting in an automobile, place
the bracket under the dash so the microphone
is readily accessible.
Attach the 4-pin microphone cable to recepta-
cle on front of unit and install unit in bracket-
securely.
Mounting and
Connections
Note
Before installing the CB radio,
visually check the vehicle bat-
tery connections to determine
which battery terminal, posi-
tive or negative (positive is the
larger of the two) is grounded
to the engine block
(or chassis).
OperationInstallation
SQUELCH
VOLUME
DW
SCAN
S 1 3 5 9 +30
P .5 1 2 3 4
CB / WEATHER
CH 9 / 19
1
4
Turning on
Turn volume control clockwise to turn power on
and set the desired listening volume.
CB Antenna
Only a properly matched antenna system will
allow maximum power output.
In mobile installations (cars, trucks, boats, etc.),
an antenna system that is non-directional should
be used.
When installed in a boat, the transceiver will not
operate at maximum efficiency without a ground
plate unless the vessel has a steel hull. Before
installing the transceiver in a boat, consult your
dealer for information regarding an adequate
grounding system.
Turning on
Your Radio
Operation
CB Antenna
OFF
Note
Cobra loaded-type antenna
models HGA 1000, HGA 1500,
and HGA 2000 are highly rec-
ommended for most installa-
tions. Consult your Cobra deal-
er for further details (or see
order form at the back of
this book).
3-Way Combination Antennas
are available which allow oper-
ation of all three bands (AM-FM
& CB), using a single antenna.
However,use of this type of
antenna usually results in less
than normal transmit and
receive range when compared
to a standard-type "Single
Band" antenna designed for
CB only.
5
Microphone Connector
Allows for convenient removal of the microphone
plug when storage is required.The microphone
MUST be connected to the unit at all times when in
use, for proper operation.
Squelch
This control is used to cut off or eliminate receiver
background noise in the absence of an incoming
signal. Adjust until the receiver noise disappears.
This will require the incoming signal to be slightly
stronger than average receiver noise. Further clock-
wise rotation will increase the threshold level
which a signal must overcome in order to be heard.
Only strong signals will be heard at a maximum
clockwise setting.
Microphone
Connector
Operation
OFF
OFF
Squelch
SHIELD
AUDIO
RX
TX
1
2
3
4
NOISE
WEAK SIGNALS
MEDIUM SIGNALS
STRONG SIGNALS
G ATE C L O S E D
NOISE
WEAK SIGNALS
MEDIUM SIGNALS
STRONG SIGNALS
NOISE
WEAK SIGNALS
MEDIUM SIGNALS
STRONG SIGNALS
G ATE
O P E N
NOISE
WEAK SIGNALS
MEDIUM SIGNALS
STRONG SIGNALS
6
Operation
Gate open
Gate closed
Setting
Squelch
Setting Squelch
Squelch is the control gate for incoming signals.
1. Full clockwise rotation closes the gate
allowing only very strong signals to enter.
2. Full counterclockwise rotation opens the gate
allowing all signals in.
OFF
OFF
7
3. To achieve the Desired Squelch Setting (DSS),
turn the Squelch control counterclockwise until
you hear noise. Now turn the control clockwise
just until the noise stops. This is the DSS setting.
Operation
NOISE
WEAK SIGNALS
MEDIUM SIGNALS
STRONG SIGNALS
G ATE
Gate set to Desired
Squelch Setting (DSS)
O
FF
Channel
Selection
8
Set CB or WX Mode
Set on CB mode. Rotate channel knob clockwise
until desired channel is displayed.
Channel 9/Channel 19
Press CH 9/19 to obtain instant access to emergency
channel 9. Press again for information CH 19.
CB/Weather
CB mode is for normal CB operation. Press
CB/Weather again and select active Weather channel
in your area.
Operation
OFF
OFF
PRESS AND RELEASE
OFF
Channel 9/
Channel 19
CB Weather
PRESS AND RELEASE
9
Dual Watch
This features allows the user to scan between two
selected channels.
1. Select first channel, CB mode.
2. Press and hold DW until LED begins flashing and
beeps once.
3. Select second channel. Press DW until LED lights
steady and radio beeps twice. Two channels are
now stored in DW memory.
Scan
Press and release SCAN button to activate CB scan
mode. If the radio is squelched, radio begins to scan.
When scan is interrupted by a signal, scan stops and
holds until loss of signal. Press PTT on mic to stop
scan function. Press Scan to restart CB scan.
Operation
Dual Watch
Note
The radio needs to be
squelched before DW can
monitor both channels.
OFF
Scan
Note
On some channels squelch
setting might have to be re-set.
PRESS AND HOLD
OFF
PRESS AND RELEASE
10
The SoundTracker System reduces noise while
leaving the signal intact in the reception mode.
In the transmission mode, it strengthens the sig-
nal, providing you with a significant reduction in
noise on reception and transmission.
How SoundTracker works
On Reception–
“Cuts Noise Coming In
With a normal CB, distant signals fall below the
squelch level and are unintelligible.With a
SoundTracker CB, the noise level is cut by up to
90%, which increases the signal-to-noise ratio
and dramatically improves signal clarity.This also
allows you to significantly reduce the squelch
level, which greatly expands your listening range.
On Transmission–
“Strengthens Signals Going Out”
A SoundTracker CB strengthens the transmit sig-
nal by more effectively using the available RF
power output of the CB.The result is improved
transmission signal clarity and an expanded
transmission range.
Soundtracker
System
Operation
USPat.No. 6,038,429
11
Activating Soundtracker
1. Press the SoundTracker button on the upper
left side of front panel. A red indicator will
illuminate when the SoundTracker system is
engaged.
Activating
Soundtracker
Operation
OFF
PUSH AND RELEASE
12
S/RF Power Meter
Shows relative transmitter RF output power and
input signal strength when receiving.The LED
(Light Emitting Diode) segments glow green to
amber to red...this indicates receive or transmit
activity.
RX/TX Indicator LED
RX indicator will light when in the receive mode.
TX indicator lights when in transmit mode.
When weather channel is selected,WX indicator is
illuminated, and the channel is displayed.
S/RF
PowerMeter
Operation
OFF
OFF
RX/TX
Indicator LED
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Cobra 18 WX ST II bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Cobra 18 WX ST II in de taal/talen: Engels als bijlage per email.

De handleiding is 1,61 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info