Handleiding Clatronic DR 3280 (pagina 30 van 56) (Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools)

534819

Verklein

Vergroot

Pagina terug

1/56

Pagina verder

ENGLISH

Unpacking the Device

• Remove the main device and accessories from the box.

• Also remove any packaging materials that may be present.

• Check the scope of delivery.

Initial Operation

Filling up the Heating Boiler before Use!

Before the tank cap is opened it must be ensured that the device

is not under any pressure. Please proceed as follows:

1. Remove the plug from the socket.

2. Turn the lock (22) on the steam pistol (20) to ON (Fig. B1).

3. Press the steam switch (21) on the steam pistol (Fig. B2).

Point the steam nozzle at a surface which is allowed to

become wet.

ޥ NOTE:

After prolonged periods of non-use it is normal for a small

quantity of condensation to come out of the steam pistol

at ﬁ rst.

WARNING:

• If the device is still warm after an interruption to

its use there is a danger of injury!

• Please open the safety lock (6) only when no more

steam comes out of the nozzle.

4. Turn the lock in an anticlockwise direction.

ޥ NOTE:

For your protection the safety lock has a release device.

If the pressure in the kettle is still too high, this release

device prevents it from being opened.

5. Shake any residual water out of the kettle (7). Fill freshwater

from the measuring beaker (15) into the kettle. Take care of

water splashes that might come out of the boiler. In order to

avoid water spray, please use the funnel supplied (Fig. E).

The water should be ﬁ lled in slowly.

CAUTION:

• Do not overﬁ ll! Max. water capacity: 1.5 litres

• Do not use condensation from a tumble dryer (chemi-

cal residues)! This is not distilled water!

6. Retighten the safety lock (6) in a clockwise direction.

Attachment of the Individual Accessories

It is possible to attach the individual nozzles directly to the steam

pistol (20) of the hose (1):

• Attach the jet nozzle (14) to the steam pistol until it locks in

place.

• In order to release the nozzle again, please press the button

on the steam pistol.

• Keep the button pressed down and then pull the nozzle off.

Or extend the nozzle attachments with one or two extension

tubes (8):

• Please insert the sections of the 2-part extension tube one

inside the other until it locks into place (Fig. G). Then attach

it to the steam pistol (20).

• Attach the ﬂ oor brush (18) to the extension tubes: press the

jointed adapter (17) on to the ﬂ oor brush and turn it tightly

through 180°.

• If you would like to use the non-woven cloth, attach it to the

ﬂ oor brush with the help of the clips (Fig. H).

• In order to release the extension tube, please press the but-

ton on the steam pistol.

ޥ NOTE:

Various attachments can only be used in conjunction with the

adapter (13). Place this on the jet nozzle (14) and ﬁ x it in place

by turning through 90°. Please note the bolts in the adapter

and the guiding groove in the jet nozzle. Check that everything

is properly connected!

Nozzle Adapter Use

Floor brush (18) Jointed

adapter

(17)

• for large ﬂ oor surfaces

(Fig. J)

• with non-woven cloth: for

sensitive surfaces (Fig. K)

Round brushes

(11)

Jet nozzle

(14)

with adap-

ter (13)

• for joints, ﬁ ttings, grill grid

etc or

• for difﬁ cult-to-access areas

(Fig. I and L)

High-pressure

nozzle (12)

Jet nozzle

(14)

with adap-

ter (13)

• for concentrated, high

steam pressure (Fig. M)

Window wiper

(19)

Jet nozzle

(14)

with adap-

ter (13)

• for windows or shower

partitions

Jet nozzle (14) Adapter

(13)

• without attachments, e.g. for

car wheel rims (Fig. N)

WARNING: THERE IS A DANGER OF INJURY!

Never attach or remove the accessories if the steam switch

(21) is pressed in! Wait until the device has cooled down.

Electrical Connection

1. Before inserting the plug into the socket. Make sure that the

mains voltage to be used matches that of the device. You

can ﬁ nd this information on the nameplate.

2. Connect the device to a duly installed 230V/50Hz protective

contact socket.

Connected Wattage

The station has a total maximum wattage of 1500 W.

05_DR 3280.indd 3005_DR 3280.indd 30 18.12.2008 9:28:51 Uhr18.12.2008 9:28:51 Uhr

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Clatronic DR 3280 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info