Handleiding Clatronic BZ 3740 (pagina 47 van 78) (Nederlands, Duits, Engels, Frans, Italiaans, Spaans, Pools)

686431

Verklein

Vergroot

Pagina terug

1/78

Pagina verder

BZ3740_IM 07.03.19

Operation

CAUTION:

Before switching of the beer dispenser, always ensure

that no 5 litre party keg is present in the dispenser as the

beer in the keg becomes warm and is no longer fresh.

Close the lid of the appliance. It must audibly snap.

Electric Connection

1. Ensure that your mains power corresponds with the

specications of the appliance. The specications are

printed on the type label.

2. Connect the mains cable to a properly installed and

earthed wall outlet.

Turning the Appliance On / Off

• Set the switch to the “ I ” position to turn the appliance on.

• The appliance is turned off when in the “

” position.

Temperature Adjustment

NOTE:

The appliance saves the most recently set cooling tem-

perature while switching it off.

After switching the appliance on again, the display will show

the current temperature of the inserted beer keg and the

last set cooling temperature.

• You can choose a cooling temperature ranging from 2 °C

to 12 °C.

• In order to display the set temperature, you may briey

press the

or button.

• Press and hold the or button to adjust the temper-

ature setting.

Pressure Regulator for Carbon Dioxide

(Exception: Heineken kegs)

Use the pressure regulator to select the appropriate pres-

sure for your beer. As different beer varieties are carbonated

to a differing extent, different pressures (saturation pres-

sure) are required to ensure the quality of the respective

beer. If a beer is dispensed with insufcient pressure, for

example, it can make the beer taste at, whilst too much

pressure can make it too zzy. If the beer should be too

zzy or at, simply adjust the pressure accordingly. To be

noted is that the CO

content in the beer initially changes

over the course of time.

NOTE:

Make sure the pressure regulator is always in the “

”

position when

• the beer drawing procedure is interrupted.

• you replace the CO

cartridge or the keg.

• In case you can no longer draw beer, even though there

is still beer in the keg, or foaming requires too much

time, slowly turn the pressure regulator towards “

” for

5 seconds. Then set the pressure regulator back to the

“

” position.

Drawing Beer

1. Preparing glasses

Wash the glasses in hot water with a small amount of

washing / up liquid. Rinse the glasses thoroughly each

time before dispensing with cold, clear water.

Ensure that all grease and residues are removed com-

pletely to avoid impairing foam formation.

NOTE:

The best results can be achieved by using glasses

exclusively for beer to ensure that no residues from fat

containing drinks (e. g. milk) are present.

2. Dispensing beer

Hold the glass under the beer tap at an angle. The tip

of the outlet tube should not come into contact with the

glass as this can impair the foam formation.

NOTE:

The foam produced when dispensing beer can be

inuenced by changing the angle of the glass.

Pull down the tap handle in one motion.

NOTE:

If the tap is only partly open, the beer may foam exces-

sively as it is not able to ow out freely.

Allow the beer to run down the inside of the glass and

slowly straighten the glass while dispensing until it is

upright towards the end.

When the foam reaches the rim of the glass, close the

beer tap by pushing back the beer tap handle.

Place the glass on the drip plate and wait until the foam

has settled. Ensure that the glass is not located directly

under the beer tap so that no drops fall into the bear

foam.

Repeat the dispensing process until the beer and foam

are in the correct proportion. This is the case when the

head is about two nger’s breadth high and slightly over

the rim of the glass.

Replacing the Carbon Dioxide (CO

) Cartridge

(Exception: Heineken kegs)

WARNING for frostbite:

• Do not remove the CO

cartridge before it is com-

pletely emptied.

• A residual amount of CO

may still be present in the

cartridge, which suddenly empties and results in the

formation of ice.

Once no beer can be drawn, even though the pressure

regulator is in the “

” position and there is still beer in the

keg, replace the CO

cartridge.

1. Switch off the appliance.

2. Disconnect the mains plug from the socket.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Clatronic BZ 3740 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info