650695
5
Verklein
Vergroot
Pagina terug
1/136
Pagina verder
Getting Started
Feature Overview
Cisco SPA100 Series Administration Guide 5
1
You can keep the default settings or configure these tones in the Call Progress Tones
section of the Regional page.
Call Progress Tone Pass Through
This feature allows the user to hear the call progress tones (such as ringing) that are
generated from the far-end network.
Echo Cancellation
Impedance mismatch between the telephone and the IP Telephony gateway phone port
can lead to near-end echo. The ATA has a near-end echo canceller that compensates for
impedance mismatch. The ATA also implements an echo suppressor with Comfort
Noise Generator (CNG) so that any residual echo is not noticeable. This feature is
enabled by default. You can configure this setting in the Audio Configuration of the
Line 1 and Line 2 Settings (PHONE 1 and PHONE 2) page.
Hook Flash Events
The ATA can signal hook flash events to the proxy during a connected call. This
feature can be used to provide advanced mid-call services with third-party-call control.
- Depending on the features that the service provider offers using third-party-call-
control, you may need to disable Call Waiting Service, Three Way Conference
Service, or Three Way Call Service to correctly signal a hook flash event to the
softswitch. You can configure these settings in the Supplementary Service
Subscription section of the Line 1 and Line 2 Settings (PHONE 1 and PHONE 2)
page.
- You can configure the length of time allowed for detection of a hook flash by
adjusting the Hook Flash Timer parameter in the Control Timer Values section of
the SIP page.
Configurable Dial Plan with Interdigit Timers
The ATA has three configurable interdigit timers: an initial timeout signaling that a
phone is taken off hook, a long timeout signaling the end of a dialed string, and a short
timeout, signaling that more digits are expected. For more information, see
Configuring Dial Plans, page 138.
Polarity Control
The ATA allows the polarity to be set when a call is connected and when a call is
disconnected. This feature is required to support some pay phone system and
answering machines. You can configure these settings in the FXS Port Polarity
Configuration section of the Line 1 and Line 2 Settings (PHONE 1 and PHONE 2)
page.
Calling Party Control
Calling Party Control (CPC) signals to the called party equipment that the calling party
has hung up during a connected call by momentarily removing the voltage between the
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Cisco Cisco SPA112 VoIP bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Cisco Cisco SPA112 VoIP in de taal/talen: Engels als bijlage per email.

De handleiding is 1,31 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info