605005
20
Verklein
Vergroot
Pagina terug
1/28
Pagina verder
20
9 Perform Initial Configuration
This section provides the procedures for performing the initial configuration of your Cisco 815 integrated services router.
Configure the Router Using Cisco Router and Security Device Manager
Cisco Router and Security Device Manager (Cisco SDM) is a web-based configuration tool that allows you to configure LAN
and WAN interfaces, routing, Network Address Translation (NAT), firewalls, VPNs, and other features on your router. If Cisco
SDM is installed on your router, configure the router by following the instructions in the Cisco Router and Security Device
Manager Quick Start Guide. If this document was not shipped with your router, you can obtain Cisco SDM and instructions
for installing it on your router from the following location:
http://www.cisco.com/go/sdm
Note To obtain the Cisco SDM release notes, and other Cisco SDM documentation, go to http://www.cisco.com/go/sdm and
click the Technical Documentation link.
Setting Up the Initial Configuration Using the Setup Command Facility
This section shows how to use the setup command facility to configure a hostname for the Cisco 815 integrated services router,
to set passwords, and to configure an interface for communication with the management network. If the following messages
appear at the end of the startup sequence, the setup command facility has been invoked automatically:
--- System Configuration Dialog ---
At any point you may enter a question mark '?' for help.
Use ctrl-c to abort configuration dialog at any prompt.
Default settings are in square brackets '[]'.
Would you like to enter the initial configuration dialog? [yes/no]:
The setup command facility prompts you for basic information about your Cisco 815 integrated services router and network,
and it creates an initial configuration file. After the configuration file is created, you can use the CLI or Cisco Router and
Security Device Manager (Cisco SDM) to perform additional configuration.
The prompts in the setup command facility vary with the installed interface modules and the software image. The following
example and the user entries (in
bold) are shown as examples only.
For help with interface and port numbering, see the “Interface Numbering” section on page 17.
Note If you make a mistake while using the setup command facility, you can exit and run the setup command facility again.
Press Ctrl-C, and type setup at the privileged EXEC mode prompt (Router#).
Step 1 To proceed using the setup command facility, enter yes when the power-up messages have ended.
Would you like to enter the initial configuration dialog? [yes/no]: yes
Note If these messages do not appear, Cisco SDM and a default configuration file were installed on the router at the
factory. To use Cisco SDM to configure the router, see the “Configure the Router Using Cisco Router and
Security Device Manager” section on page 20.
Step 2 When the following messages appear, press Return to enter basic management setup:
At any point you may enter a question mark '?' for help.
Use ctrl-c to abort configuration dialog at any prompt.
Default settings are in square brackets '[]'.
20

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Cisco 815 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Cisco 815 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,01 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Cisco 815

Cisco 815 Installatiehandleiding - English - 86 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info