644104
17
Verklein
Vergroot
Pagina terug
1/56
Pagina verder
17
English
Step 2:
Attach the support (2) at the main frame (1).
1. Place screws M8x16 (16), curved washers 8//20 (56) and spring
washers for M8 (52) accessibly beside the front part of the main
frame (1).
2. Place the lower end of the support (2) against the holder of main
frame (1). Plug the ends of the two computer cables (20) and
(18) projecting from (1) and support (2) together.
(Note: The computer cable harness (18) projecting from the
support (2) must not slide into the tube, as it is required for later
steps of installation.)
3. Connect the tension cable of resistance control (17) to the
bracket of lower section cable of tension (19) (See figure A1-A4).
Before this step of the installation, it is advisable to adjust the
resistance setting to the position, at which the cable extends
furthest from the sheath. Put the lowest part of cable (17) into
the small hook of lower tension cable (19) (figure A1). Pull it
(figure A2) until the small hook get in higher position (figure A3)
and then insert the cable (17) onto the bracket (19) (figure A4).
When joining the tubes, ensure that the cable connection is not
trapped.
4. Put one spring washer (52) and one washer (56) on each screw
(16). Push the screws (16) through the holes in the support (2),
screw into the threaded holes of the main frame (1) but don’t
tighten them firmly. (This screw connection point will screw
tightly at least in Step 4)
Assembly Instructions
Remove all the separate parts from the packaging, lay them
on the floor and check roughly that all are there on the base of
the assembly steps. Please note that a number of parts have
been connected directly to the main frame and preassembled.
In addition, there are several other individual parts that have
been attached to separate units. This will make it easier and
quicker for you to assemble the equipment.
Assembly time: 35 - 45 min.
Step 1:
Attach the stabilizer (3+4) at main frame (1).
1. Attach the front foot (3) with the preassembled end caps (11)
to the main frame (1). Do this with the two screws M10x60 (12),
curved washers 10//20 (13), spring washers for M10 (67) and
cap nuts M10 (14).
2. Attach the rear foot (4) with height adjustable foot caps (15) to
the main frame (1). Do this with the two screws M10x60 (12),
curved washers 10//20 (13), spring washers for M10 (67) and
cap nuts M10 (14). After assembly has been completed, you
can compensate for minor irregularities in the floor by turning
the eccentric cap (15). The equipment should be set up that the
equipment does not move of its own accord during a training
session.
17

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Christopeit CX3 - 1531 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Christopeit CX3 - 1531 in de taal/talen: Nederlands, Duits, Engels, Frans als bijlage per email.

De handleiding is 2,05 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info