Instruction manual SAFARI CAR TOY
GB
USA
Age: 12 Months +
• Please read these instructions carefully before using the toy and keep for future reference.
• The toy is battery operated as follows: 3 x 1.5 Volt AA batteries for the panel (included), 2 x 1.5
Volt AAA batteries for the infrared remote control (included). The batteries supplied with this
product, at the point of sale, are intended for demonstration purposes only; please replace them
immediately after completing your purchase.
WARNINGS
For your child's safety: WARNING!
• Before using the product remove and dispose of any plastic bags and any other packaging (e.g.
fasteners and xing ties etc) and keep them out of reach of children. Suffocation hazard.
• Check the toy regularly for signs of wear and damage and to ensure that it is assembled correctly.
Should any part be damaged, do not use the toy and keep it out of reach of children.
• This toy must only be used under adult supervision.
• Always use the toy with the child car seat facing forwards.
• This car panel must only be assembled and tted by an adult.
• The panel can only be installed on the back of front car seats which have a head rest.
• Make sure the panel is tted correctly and rmly attached to the head rest. Check it regularly to
ensure it has not come loose.
• Never leave the panel on a vehicle seat without fastening it securely in place; it could hurt or
injure other passengers in the car.
• Remember never to turn your head to switch the toy on, or pick up the infrared remote control
while you are driving the car.
• When the rear seat is empty, the infrared remote control can be fastened to the panel using the
relative slot. When the child is sitting in the car seat, fasten the infrared remote control to the
child car seat harness only.
• This product must not be modied in any way; never fasten other ties or straps to it.
INSTALLING THE PANEL IN THE CAR
Open the buckles (A. Diag. 1) found on the back of the panel and fasten them to the supports on
the head rest. Pull the straps (B, Diag. 2) to fasten the panel rmly to the seat.
FASTENING THE INFRARED REMOTE CONTROL TO THE CAR SEAT
Fasten the infrared remote control (C, Diag. 3) to the child car seat safety harness strap (D, Diag.
3) using the velcro fastener strap. This aims to prevent the toy from falling onto the oor when
travelling by car.
HOW TO USE THE TOY
Switching it ON and Off
• To switch the toy panel ON, move the switch E (Diag. 4) from the 0 position to the I position
(Relax) or II (Fun) position according to the game mode desired.
• To adjust the volume level, move the switch F (Diag. 4) from the <)) (low) position to the <)))
(high) position.
• In order to avoid using up the batteries for no reason, it is recommended to switch off the toy by
moving the switch E (Diag. 4) to the 0 position.
• Insert the batteries in the walkie-talkie style infrared remote control before using it; it only works
when the toy panel is set to Fun mode.
• To start the game functions, point the sensor on the infrared remote control at the panel (Diag.
4.1).
Play modes
1. RELAX: to enable this play mode, move the switch E (Diag. 4) to the I position.
The low lights and soft music gently soothe your baby. The infrared remote control does not work
when the toy is operating in this play mode. The toy will switch off automatically after 15 minutes.
To restart it, switch it off by moving the switch to the 0 position. Then switch it back on and set
the desired play mode.
2. FUN: to enable this play mode, move the switch E (Diag. 4) to the II position. A jingle will con-
rm the play mode choice. When set to Fun mode, every time the child presses one of the buttons
on the infrared remote control (Diag. 5) the relative sound effect will play. If the same button is
pressed a number of times, a tune will play. In both cases, the images linked to the buttons will be
displayed on the panel so your baby will learn to recognise them. When set to FUN mode, if the
toy is not used for about 20 minutes, it will play a sound effect and switch off automatically. To
restart it, switch it off by moving the switch to the 0 position. Then switch it back on and set the
play mode of your choice.
HOW TO FIT AND REMOVE THE REPLACEABLE BATTERIES
• To replace the panel batteries: loosen the screw on the battery compartment cover (G, Diag. 6)
on the back with a screwdriver and remove the cover; then remove the at batteries and t new
ones, ensuring that the battery polarity is correct (as shown on the product), close the battery
compartment cover, and tighten the screw rmly.
• To replace spent batteries inside the infrared remote control: open the velcro fastener on the
back, loosen the screw on the battery compartment cover (H, Diag. 7) on the back with a screw-
driver and remove the cover; then remove the at batteries and t new ones, ensuring that the
battery polarity is correct (as shown on the product), close the battery compartment cover, and
tighten the screw rmly. Close the velcro fastener rmly when you have nished changing the
batteries.
WARNING
• Batteries must only be tted by an adult.
• Always keep batteries and tools out of the reach of children.
• Always remove spent batteries from the toy to avoid the danger of leakage from the battery
damaging the product.
• Always remove the batteries if the product will not be used for a long period of time
