Handleiding Charnwood Haven (pagina 4 van 20) (Engels)

815471

Verklein

Vergroot

Pagina terug

1/20

Pagina verder

Operating & Installation Instructions

CONTENTS

QUICK GUIDE 4

OPERATING INSTRUCTIONS 5

FUEL 5

LIGHTING 5

CONTROLLING THE FIRE 6

WOOD ASH REMOVAL GRATE 6

RIDDLING 6

REFUELLING 7

ASH CLEARANCE 7

COOKING 7

OVEN THERMOMETER 7

REDUCED BURNING 7

MAINTENANCE 7

THROAT PLATE AND FLUEWAY CLEANING 8

CHIMNEY SWEEPING 9

TROUBLE SHOOTING 9

CO ALARM 10

IF YOU NEED FURTHER HELP 10

INSTALLATION INSTRUCTIONS 11

UNPACKING THE STOVE 11

HEALTH AND SAFETY PRECAUTIONS 11

SPECIFICATION 11

CO ALARMS 12

CHIMNEY 12

HEARTH AND FIRE SURROUND 12

CONNECTIONS TO FLUES 12

SOOT DOORS 13

PRE LIGHTING CHECK 13

COMMISSIONING 13

CAA AND SMOKE CONTROL 13

HAVEN DIMENSIONS 15

HAVEN PARTS LIST 16

CERTIFICATION 17

Ref.Haven v5 11.2023

QUICK GUIDE

Throat plate

Improves efficiency of stove by slowing

down flue gases

Doors

Keep closed when stove is in use

Door handles

Fire Door - twist clockwise and pull to open

Oven - pull to open

Front Fence

Protects glass and prevents spillage

Sliding Ashpan

For clean and easy ash removal

MAINTENANCE AND CLEANING

COOKING

PLATE

Maintain by lightly oiling the cook plate with vegetable oil. Wipe clean with

a non abrasive cloth and mild soap.

GLASS Wipe with damp, lint free cloth. Any stubborn deposits on the glass may

be removed with a proprietary stove glass cleaner or ceramic hob cleaner.

THROAT PLATE Take down once a month and clean. Sweep sooty deposits into fire

CHIMNEY Have chimney swept twice a year.

SERVICING Stove should be serviced by a professional at least once a year.

Suitable fuels for your

Charnwood:

Wood logs

Unsuitable fuels:

Petroleum coke

Liquid fuel

Household waste

Coal singles

Small nuts or coal dust

Wet or unseasoned wood

Smokeless mineral fuel

LIGHTING AND CONTROLLING THE FIRE

High

Output Nominal

Click Low

Output

AIR CONTROL

Put the grate into the open

position by rotating the tool anti -

clockwise. Place 2 small, dry, well

seasoned logs into the bottom of

the firebox running from front to

back. Keep air control fully out

and door cracked open.

Open the flue gas diverter by

pulling the tool forward. Build

a stack of 6-8 softwood kindling

sticks. This can be in grid shape

or a pyramid with paper or

firelighter in the centre, ensure

to leave a space between the

pieces to allow the air to circulate

around and through them and

light.

Add larger logs once fire is

established. The air control can

be reduced to the nominal click

position. If cracked open, the

door can now be closed. Set

the flue diverter into the normal

position (push back)

Rotate the tool

anti-clockwise.

Rotate the tool

clockwise. (into position 1)

OPERATING INSTRUCTIONS

Congratulations on becoming the owner of a Charnwood Haven

Stove. Your stove has been approved in smoke controlled areas to

burn wood logs if it is used in accordance with these instructions. It

is very important that you read and understand these instructions

before using the stove.

Before lighting the stove check with the installer that the work and

checks described in the Installation Instructions have been carried

out correctly and that the chimney has been swept, is sound and free

from any obstructions. The stove is not suitable for use in a shared

flue system.

If you are using your stove to burn wood logs in a smoke controlled

area, then the provided Defra Stop MUST be fitted and the

instructions on lighting and refuelling MUST be followed. This stove

will not produce significant smoke if well seasoned logs of less than

20% moisture content are burnt and these instructions are adhered

to. Burning wet (>20% moisture content) wood and operating the

stove in an irresponsible manner may produce smoke which is illegal

in smoke controlled areas.

Remember that the stove will be hot and that it is made from hard

materials – ensure that you have good balance before operating the

fire. Always use the provided operating tool and gloves.

Do not use an aerosol spray on or near the stove when it is alight.

There is a risk of explosion or flash ignition of the spray.

When using the stove in situations where children, aged and/or infirm

persons are present a fireguard must be used to prevent accidental

contact with the stove. The fireguard should be manufactured in

accordance with BS 8423:2002.

The stove is suitable for intermittent operation.

FUEL

This stove has been designated to burn wood. Only dry, well

seasoned wood should be burnt on this appliance as burning wet

unseasoned wood will give rise to heavy tar deposits in the stove, on

the glass and within the chimney. For the same reason hard woods

(such as Ash, Beech and Oak) are better than soft woods (such as

Pine and Spruce). Burning wet unseasoned wood will also result in

considerably reduced outputs. The wood should be cut and split and

then left to season in a well ventilated dry place for at least one year

but preferably two years before use.

Approximate suitable log sizes are:

180mm(7in) - 210mm (8.25”) long and 75mm (3in) diameter

Log moisture content of less than 20% is recommended.

PETROLEUM COKE IS NOT SUITABLE FOR USE ON THIS

APPLIANCE. ITS USE WILL INVALIDATE THE GUARANTEE.

This stove is not designed to burn household waste.

LIGHTING

IMPORTANT Before beginning to light the fire, set the flue gas

diverter in the lighting position by placing the tool into the gas

diverter control and pulling it forward (illustrated in Fig.1).

On initial lighting, the stove may smoke and give off an odour as the

silicon paint with which the firebox is painted reacts to the heat. This

is normal and will cease after a short time, but meanwhile the room

should be kept well ventilated.

At first only light a small fire and burn it slowly for two hours to allow

any residual moisture in the chimney to evaporate.

Before building the fire, the grate must be put in the open position.

This is done by turning the operating tool anti-clockwise in the

riddling lever (illustrated in fig.2). Place 2 small logs on the grate

running from front to back with a small gap between them. Build

a stack of 6-8 softwood kindling sticks on top of the logs. This can

be in grid shape or a pyramid, with a firelighter or paper in the

centre, ensure to leave space between the kindling to allow the air to

circulate around and through them. Open the air control fully (see

quick guide page 4) Light the paper or fire lighters. The door may be

left cracked open for a few minutes to assist the combustion and heat

up the firebox more quickly.

When the kindling wood is well alight add a few more small logs,

close the door but leave the air control fully open. When the flames

are established around these logs, load the stove with the required

fuel load. Maintain the air control at maximum at this stage. Once the

fire is up to temperature the airwash system will begin to work, so

allow the fire to become hot before adjusting the air control to the

required setting. At this point the flue gas diverter should be moved

to the normal position - place the tool in the control and push it

backwards in an anti-clockwise direction (see Fig.1), and the oven

should begin to heat up. During the lighting period, do not leave the

stove unattended. Do not leave the door open except as directed

above to avoid excessive smoke.

When relighting the stove, leave the ash on the base, unless it is

becoming too deep, in which case some of it may be removed by

riddling the grate to empty it into the ashpan.

CONTROLLING THE FIRE

The rate of burning and hence the output is controlled by the air

control (see Fig.1)

Open the air control fully (high position) when lighting or when rapid

burning is required. It should not be left fully open for long periods

as this can cause over-firing or excessive smoke production. For most

efficient output move the air control to the ‘nominal position’ or for

low burning to the low position.

When the fire is burning normally the air control gives enough

airwash to keep the glass clean. However, it will not always be

possible to keep the glass clean with the air control fully closed. For

correct firing we recommend the use of a stove pipe thermometer

which may be purchased from your supplier or from Charnwood.

The Charnwood Haven is fitted with an air control stop for use in a

smoke control area. This stops the stove from burning too slowly.

WOOD ASH REMOVAL GRATE

Your Charnwood Haven is fitted with a wood ash removal grate to

enable wood to be burned and ash to be cleared.

Movement of the grate from one position to the other is effected

using the operating tool supplied as shown in Fig.2.

The grate is put into the open position by turning the operation tool

anticlockwise. The grate is put into the closed position by turning

the operation tool clockwise. To riddle the appliance the tool should

be moved between the clockwise and anticlockwise positions several

times. When burning wood, the grate must be in the ‘open’ position

as shown in Fig.2.

RIDDLING

When burning wood, ash should be allowed to build up and only

riddled when the ash begins to cover the rear fireplate. The fire

should be riddled with the fire door shut (see Fig.2). Place the

operating tool into the riddling lever and rotate between the open

and closed positions several times. Too much riddling can result

in emptying unburnt fuel into the ashpan and should therefore be

avoided. After riddling, the grate should be put back into the open

position.

Fig. 2 Riddling

OPERATING INSTRUCTIONS

Nominal

click

High

Output Low

Output

AIR CONTROL

Oven handle

Pull to open

Riddling knob

Use the operating tool to

riddle. The stove should be

run with the grate in the

‘open’ position. (See fig. 2)

Operating

tool storage

Store the

operating tool

when not in

use

Oven

thermometer

Indicates

approximate oven

temperature

Serial label

Slide out to view,

scan QR code to

Cooking plate

The temperature of the cooking plate is graded, with the hottest point

located directly above fire for boiling.

Flue Diverter

Forward ( Position 1) -

Lighting

Back (Position 2) -

Normal operation

Fire Door Handle

Twist clockwise to

open

Fig. 1. Stove Controls

Open

Riddle

Closed

OPERATING INSTRUCTIONS

REFUELLING

Keep the firebox well filled but do not allow fuel to spill over the top

of the fuel retainer.

Logs should be evenly distributed, filling the firebed to give the most

pleasing flame pattern. The air control must be fully opened after

refuelling until the flames are established above the fire. It is best to

refuel on to a hot bed of embers. If at this point the fire starts to die,

the door must be cracked open until the fire is revived. If the fire has

started to die down before refuelling, then more kindling wood must

be added, the air control opened fully and the door cracked open

to re-establish the firebed before adding larger logs (see suitable log

sizes in Fuel section). This will avoid excessive smoke emission.

Care should be taken that logs do not project over the fuel retainer

or damage to the glass may be caused when the door is closed. It can

also cause the glass to blacken up. Maximum filling height is such that

logs cannot fall from the fire when the door is opened.

Do not fill the stove above the level of the air holes in the back bricks,

as overloading can cause excess smoke.

Do not operate with the door open except as directed by the

instructions as this can cause excessive smoke.

ASH CLEARANCE

Before removing ash ensure that it has cooled down. The ashpan

slides out for easy ash removal.

To make ash removal easier there are ash carriers available. These

may be purchased from your supplier or, in case of difficulty, from

Charnwood.

Fig. 3 Ashpan removal

COOKING

Once the fire is alight and well established make sure the flue diverter

is in the normal position (position 2). This is illustrated in the quick

guide on page 4 and Fig. 1. Stove Controls.

The temperature of the cooking plate is graded, with the hottest

point for boiling located directly above the fire on the left-hand side.

If the optional rear shelving is fitted, the shelving will remain warm

whilst the fire is lit and can be used as a warming plate for keeping

food or plates warm whilst cooking.

OVEN THERMOMETER

The oven thermometer gives a good guide of the temperature of

the centre of the oven. Some experimentation will be necessary to

find the best settings for different recipes. You will generally find

that the higher shelf positions will give higher temperatures. Once

you have lit the fire and the oven is nearly at the required cooking

temperature keep the air control at the nominal click setting and

refuel as necessary to maintain the temperature. As a rough guide,

adding a single log will give around 40 minutes of cooking time when

running at nominal.

REDUCED BURNING

For reduced burning the fire door must be closed.

When burning wood in areas that are not smoke controlled, load

some large logs on the fire and allow to burn for half an hour before

closing the air control (this will help to reduce tar deposits in the

chimney). Some experimentation may be necessary to find the

setting most suitable for the type of fuel being used and the draw on

the chimney.

MAINTENANCE

Cleaning

The stove is finished with a high temperature paint which will

withstand the temperatures encountered in normal use. This may

be cleaned with a damp lint-free cloth when the stove is cold. Should

re-painting become necessary, high temperature paints are available

from your supplier or from stove shops. Any grease or stains from

cooking can be removed by using a mild detergent or stove cleaning

product.

Cleaning the Glass

Most deposits on the glass may be burnt off simply by running the fire

Operating tool

Extra carry handle

Use with glove

OPERATING INSTRUCTIONS

at a fast rate for a few minutes. If it becomes necessary to clean the

glass then open the door and allow it to cool. Clean the glass using

a damp cloth and then wiping over with a dry cloth. Any stubborn

deposits on the glass may be removed with a proprietary stove glass

cleaner or ceramic hob cleaner. Do not use abrasive cleaners or pads

as these can scratch the surface which will weaken the glass and cause

premature failure

When Not in Use

If the fire is going to be out of use for a long period (for instance in

the summer) then to prevent condensation, and hence corrosion,

the air control should be left fully open, the fire door left ajar and

the flue diverter set in the lighting position. It Is also advisable to

sweep the chimney and clean out the fire. Spraying the inside of the

door with a light oil, such as WD40, will also help to keep all internal

parts working well. After long periods where the fire has been out

of use, the chimney and appliance flueways should be cleaned before

lighting.

Door Seals

For the fire to operate correctly it is important that the door seals

are in good condition. Check that they do not become worn or

frayed and replace them when necessary.

Servicing

It is recommended that the fire is serviced once a year to keep it in

first class working order. After cleaning out the firebox thoroughly,

check that all internal parts are in good working order, replacing

any parts that are beginning to show signs of wear. Check that the

door seals are in good condition and that the doors seal correctly.

Check the cook plate and access door seals are in good condition. A

servicing guide is available on request. Repairs or modifications may

only be carried out by the Manufacturer or their approved agents.

Use only genuine Charnwood replacement parts.

THROAT PLATE AND FLUEWAY CLEANING

It is important that the throat plate and all the stove flueways are kept

clean in order to prevent potentially dangerous fume emission. They

should be cleaned at least monthly, and more frequently if necessary.

It is necessary to let the fire out to carry out these operations.

The Haven throat plate is one brick. To remove the throat plate,

slide it forwards so that it clears the back brick, then lift and rotate

so that the opposite side clears the top of the remaining side brick

and can be gently lowered. Any sooty deposits should then be swept

from the throat plate and into the fire.

To re-fit the throat plate, offer it up at an angle. Insert the throat

plate so that it sits on top of either the right or left side brick. Raise

the opposite side and slide so that it is central and supported by the

side bricks. Slide back so that the throat plate rests neatly on the top

of the back bricks.

Fig.4 Throat Plate Location

The internal channels that distribute the hot flue gasses around the

oven should also be cleaned. To clean, carefully lift the cook plate off

the top of the stove top by tilting it with a flat head screwdriver or

by removing the throat plate and pushing it up carefully through the

appliance. The cook plate is heavy, handle with care and wear gloves.

Remove the ‘R’ clip to release the flue gas diverter and brush down

any debris with a 50mm diameter flexible brush. Remove the access

The Haven throat plate rests

on top of the back brick.

Gently tilt the cookplate

up to remove

Unscrew the access door

Replace the ‘R’ clip

to secure the flue gas

diverter

Fig.5 Cook plate, flue gas diverter and access door removal

door by unscrewing the 2 x countersunk Allen screws, then by using

a brush or a vacuum cleaner, clean out all accessible areas. Once all

areas are thoroughly cleaned, replace the flue gas diverter ensuring

the ‘R’ clip and washers are secured, replace the cook plate into

position, with the seal intact and re fit the access door.

CHIMNEY SWEEPING

If the chimney previously served an open fire, it is possible that

the higher flue gas temperature from a stove may loosen soot

deposits with the consequent risk of flue blockage. It is therefore

recommended that the chimney be swept a second time within a

month of regular use after installation.

The chimney should be swept at least twice a year. As it is not

possible to sweep through the appliance the installer will have

provided alternative means, such as a soot door in the connecting

flue pipe. After sweeping the chimney the appliance flue outlet and

the flue pipe connecting the stove to the chimney must be cleaned.

After clearing any soot from within the stove, replace the throat

plate (see Fig. 4 ).

Different types of sweep’s brushes are available to suit different

flueways. For prefabricated insulated chimneys the manufacturers

instructions with regard to sweeping should be consulted.

TROUBLE SHOOTING

Fire Will Not Burn

Check that:

a) the air inlet is not obstructed in any way,

b) chimneys and flueways are clear,

c) a suitable fuel is being used,

d) there is an adequate air supply into the room,

e) If an extractor fan is fitted, that it is not causing lack of flue draft

when operating.

f) there is sufficient draw in the chimney. Once the chimney is warm

a draught reading of at least 1.25 mm (0.05 in.) water gauge (12Pa)

should be obtained.

Blackening of Door Glass

Differences in chimney draughts mean that the best settings of the

air controls will vary for different installations. A certain amount of

experimentation may be required, however the following points

should be noted and with a little care should enable the glass to be

kept clean in most situations:

a) Wet or unseasoned wood, or logs overhanging the front fence will

cause the glass to blacken.

b) The airwash relies on a supply of heated air to keep the glass clean,

therefore, when lighting the stove allow the firebed to become well

established before closing the air control. This may also be necessary

when re-fuelling the stove.

c) When re-fuelling keep the fuel as far back from the front fence as

possible, do not try to fit too much fuel into the firebox

d) Do not completely close the air control.

It is always more difficult to keep the glass clean when running the

stove very slowly for long periods.

If blackening of the glass still occurs check that all flue connections

and the blanking plate are well sealed. It is also important that the

chimney draw is sufficient and that it is not affected by down-draught.

When the chimney is warm a draught reading of at least 1.25 mm

(0.05 in.) water gauge (12Pa) should be obtained. Some blackening

of the glass may occur below the level of the fuel retainer. This will

not obscure the view of the fire or affect its performance.

Fume Emission

Warning Note: Properly installed and operated this appliance will

not emit fumes. Occasional fumes from de-ashing and re-fuelling

may occur. Persistent fume emission is potentially dangerous and

must not be tolerated. If fume emission does persist, then the

following immediate actions should be taken:

a) Open doors and windows to ventilate the room and then leave

the premises.

b) Let the fire out and safely dispose of the fuel from the appliance.

c) Check for flue or chimney blockage, and clean if required.

d) Do not attempt to re-light the fire until cause of fuming has

been identified, if necessary seek professional advice.

The most common cause of fume emission is flueway or chimney

blockage. For your own safety these must be kept clean.

Fire blazing out of control

Check that:

a) The door is tightly closed.

b) The air control slider is fully closed.

c) A suitable fuel is being used.

d) Door seals and air slide are intact.

OPERATING INSTRUCTIONS

Chimney Fires

If the chimney is thoroughly and regularly swept, chimney fires

should not occur. However, if a chimney fire does occur close the air

control, and tightly close the door of the appliance. This should cause

the chimney fire to go out in which case the controls should be kept

closed until the stove has gone out. The chimney and flueways should

then be cleaned. If the chimney fire does not go out when the above

action is taken then the fire brigade should be called immediately.

After a chimney fire the chimney should be carefully examined for

any damage. Expert advice should be sought if necessary.

CO ALARM

Your installer should have fitted a CO alarm in the same room as the

appliance. If the alarm sounds unexpectedly, follow the instructions

given under “Warning Note” above.

IF YOU NEED FURTHER HELP

If you need further help with your Charnwood then your Installer

will be able to provide the answers to most questions. Your Local

Charnwood Premier Dealer has a great deal of experience and will

also be able to provide helpful advice. Further help is available from

the Charnwood Customer Services department who will be pleased

to give advice, if necessary.

OPERATING INSTRUCTIONS

UNPACKING THE STOVE

The stove arrives bolted and strapped to its pallet. There must be

adequate facilities for unloading and manoeuvring into position. The

wrapping is first removed, then the stove released from the pallet by

removing 4 pallet bolts using a 10mm spanner. The pallet brackets

can now be removed from the stove by tilting it and using a 13mm

spanner to remove the bolts. The pallet is intended to be cut up and

used for kindling fuel.

The cooking plate is wrapped in greaseproof paper and secured by

a band. To release the cooking plate, cut the band that is attached

to the airwash tube above the throat plate. The band is visible by

looking into the top of the fire chamber. The cook plate has been

oiled so gloves are recommended when handling. Once the band

has been cut, carefully lift the cook plate out of the top of the stove

top by pushing it up from underneath inside the fire chamber and

remove the greaseproof paper. When returning the cook plate, the

rope seal may first need to be ‘plumped’ up before resting the cook

plate on top. Once in place, the cook plate should be firmly pushed

down onto the rope seal to bed it in.

The heatshield underneath the stove can be removed for trucking

into position and must be returned once in position. The vertical rear

flue adaptor and flue collar will also need to be unboxed and fitted

over the rear outlet. The oven and the firebox will be packed with

items such as the oven shelves, baking tray, gloves etc.

HEALTH AND SAFETY PRECAUTIONS

Please take care when installing the stove that the requirements of

the Health and Safety at Work Act 1974 are met.

Some types of fire cement are caustic and should not be allowed to

come into contact with the skin. In case of contact wash with plenty

of water.

If there is a possibility of disturbing any asbestos in the course of

installation then please use appropriate protective equipment.

Ideally there should not be an extractor fan fitted in the same room

as the appliance. If this situation is unavoidable then specialist advice

should be taken to ensure that the extractor fan does not cause the

appliance to emit fumes into the room. The external air kit will help

with this in some situations. Alternatively, an additional air supply

correctly positioned may be necessary. It is essential to carry out a

spillage test to ensure that the appliance can operate safely when the

extractor fan is operating.

There must be an adequate air supply into the room in which the

appliance is installed to provide combustion air. The combustion air

supply must be via a permanently open vent. The requirement for

minimum free area is partly dependent on the design air permeability

of the house. In older properties the air permeability will be above

5.0m³/(h.m²), but in some modern properties it may be less.

The vent must be positioned such that it is not liable to blockage.

Minimium areas are given in the following table:

A fixed ducted air supply may be used as an alternative to the

traditional method of using a permanent open vent into a room to

supply air for combustion.

External air supply kits are available please contact Charnwood for

more information. Instruction sheet ref: TIS 120

This stove is capable of intermittent operation, and is not suitable for

use in a shared flue system.

In addition to these instructions the requirements of BS.8303 and

BSEN 15287-1:2007 must be fulfilled. Local Authority Bylaws

and Building Regulations, including those referring to national and

European Standards, regarding the installation of Solid Fuel burning

appliances, flues and chimneys must also be observed.

Haven

SPECIFICATION EN13240:2001

Fuel Wood logs

Rated Heat Output kW (BTU/hr) 6.6kW

Model weight kg (Packed) 165kg - Store Stand, 152kg - High Legs

Flue Temperature °C 154°C

Minimum Flue Draught 12Pa

Flue gas Mass Flow g/s 4.9

Hearth Temperature <100°C

Minimum distance from

combustibles mm

SIDE BACK

500 400

The outputs in the table are based on a 45 minute re-fuelling

cycle burning seasoned hardwood logs. All tests are carried out in

accordance with BSEN 13240.

AIR

PERMEABILITY

m3/(h.m2)

MINIMUM VENT AREA

cm2(in2)

Haven

>5.0 11 (1.76)

<5.0 38.5 (6.0)

INSTALLATION INSTRUCTIONS

CO ALARMS

Building regulations require that whenever a new or replacement

fixed solid fuel or wood/biomass appliance is installed in a dwelling

a carbon monoxide alarm must be fitted in the same room as

the appliance. Further guidance on the installation of the carbon

monoxide alarm is available in BS EN 50292:2002 and from the

alarm manufacturer’s instructions. Provision of an alarm must not

be considered a substitute for either installing the appliance correctly

or ensuring regular servicing and maintenance of the appliance and

chimney system.

CHIMNEY

In order for the appliance to perform satisfactorily the chimney

must give sufficient draw when warm (minimum of 12pa/0.05”

wg). The height of the chimney must comply with local

building regulation requirements. The internal dimensions

of the chimney MUST NOT BE LESS THAN 125 mm (5”)

If an existing chimney is to be used it must be swept and checked,

it must be in good condition, free from cracks and blockages, and

should not have an excessive cross sectional area. If it was previously

used by an open fire then the chimney should be swept one month

after installation to clear any soot falls which may have occurred due

to the difference in combustion between the stove and the open fire.

If you find that the chimney is in poor condition then expert advice

should be sought regarding the necessity of having the chimney lined.

If it is found necessary to line the chimney then a lining suitable for

Solid Fuel must be used.

If there is no existing chimney then a prefabricated block chimney

or a twin walled insulated stainless steel flue to BSEN 15287-1:2007

can be used either internally or externally. These chimneys must be

fitted in accordance with the manufacturers instructions and Building

Regulations.

Single wall flue pipe is suitable for connecting the stove to the chimney

but is not suitable for using for the complete chimney. If it is found

that there is excessive draw in the chimney then a draught stabiliser

should be fitted.

It is important that there is sufficient draw in the chimney and that the

chimney does not suffer from down-draught. When the chimney is

warm the draw should be not less than 1.25mm (0.05”) water gauge

(12 Pa). If in doubt about the chimney seek expert advice. The flue

draft may be measured by removing the small stop at the left hand

end of the fire door handle, and inserting the probe in the hole.

HEARTH AND FIRE SURROUND

The stove must stand on a fireproof hearth and must not be situated

closer than the minimum distance from combustible materials (see

specification table) to the sides or rear above hearth level unless

adequately fireproofed in accordance with local building regulations.

The hearth must be of fireproof material and at least 12mm (1/2in.)

thick. The positioning of the stove and the size of the hearth are

governed by building regulations for Class 1 appliances. These

building regulations state that the hearth must extend in front of the

stove by at least 225mm (9 in.) and to the sides of the stove by at

least 150mm (6 in.). When the fire door is open, it extends beyond

the flat front of the stove by 255mm.

If in doubt as to the positioning of the stove, expert advice should be

sought either from the supplier or the local building inspector. The

fireplace must allow good circulation of air around the appliance to

ensure that maximum heat is transferred to the room and also to

prevent the fireplace from overheating. A gap of 150mm (6”) each

side and 300mm (12”) above the appliance should give sufficient air

circulation. If a wooden mantelpiece or beam is used in the fireplace it

should be a minimum of 750mm (29.5”) from the appliance. In some

situations it may be necessary to shield the beam or mantelpiece to

protect it.

In order for the fire to operate correctly and to allow for access,

there must be an air gap behind the appliance of at least 50mm,

but be aware that this distance will need to be greater in some

cases to meet Building Regulation and safe distance to combustibles

requirements.

The appliance should be installed on a floor with adequate load-

bearing capacity. If an existing construction does not meet this

requirement then please take suitable measures to achieve this. (e.g.

load distributing plate.)

CONNECTIONS TO FLUES

The Haven must be connected to the flue using flue pipe of 125mm

(5”) diameter.

There are several ways of connecting the stove to the flue. These are

illustrated in Figs. 6 to 8.

The chimney cannot be swept through the appliance and a clean

out door is required. Horizontal lengths of flue must be kept to a

minimum and should not be more in length than the flue diameter.

All flue connections must be well sealed.

Fig. 6 Horizontal Register Plate With Rear Flue Connection

Fig. 7 Horizontal Register Plate With Top Flue Connection

Fig. 8 Flexible Flue LinerWith Vertical Rear Flue Connector

SOOT DOORS

In most back outlet installations it will be necessary to have a soot

door to enable the chimney to be swept. Soot doors may either

be in the actual brickwork of the chimney, the register plate or the

connecting flue pipe. Various positions of soot doors are shown in

Figs. 6 to 8.

PRE LIGHTING CHECK

Ensure that the throat plate is fitted in the roof of the appliance. For

location and positioning see Fig. 4.

Check that the front fence is fitted correctly and that the door closes

properly.

COMMISSIONING

On completion of the installation allow a suitable period of time for

the fire cement and mortar to dry out before lighting the fire. Check

to ensure that smoke and fumes are taken from the appliance up

the chimney and emitted safely. Also check all joints and seals. On

completion of the installation and commissioning please leave the

operating instructions with the customer and advise them on the use

of the appliance

CAA AND SMOKE CONTROL

The Clean Air Act 1993 and Smoke Control Areas

Under the Clean Air Act local authorities may declare the whole or

part of the district of the authority to be a smoke control area. It

is an offence to emit smoke from a chimney of a building, from a

furnace or from any fixed boiler if located in a designated smoke

control area. It is also an offence to acquire an “unauthorised fuel”

for use within a smoke control area unless it is used in an “exempt”

appliance (“exempted” from the controls which generally apply in

the smoke control area).

In England appliances are exempted by publication on a list by the

Secretary of State in accordance with changes made to sections 20

and 21 of the Clean Air Act 1993 by section 15 of the Deregulation

Act 2015. Similarly in Scotland appliances are exempted by

publication on a list by Scottish Ministers under section 50 of the

Regulatory Reform (Scotland) Act 2014.

In Northern Ireland appliances are exempted by publication on

a list by the Department of Agriculture, Environment and Rural

Affairs under Section 16 of the Environmental Better regulation Act

INSTALLATION INSTRUCTIONS

Soot door inside or rear of

chimney

Alternative soot door

positions

door

Flexible Liner

Access Door

(Northern Ireland) 2016.

In Wales appliances are exempted by regulations made by Welsh

Ministers.

Further information on the requirements of the Clean Air Act can be

found here: https://www.gov.uk/smoke-control-area-rules

Your local authority is responsible for implementing the Clean Air Act

1993 including designation and supervision of smoke control areas

and you can contact them for details of Clean Air Act requirements.

The Haven has been been recommended as suitable for use in smoke

control areas when burning wood logs. The stove includes a factory-

fitted modification to the air control to prevent complete closure of

the air supply.

INSTALLATION INSTRUCTIONS

HAVEN DIMENSIONS

To suit 125mm

(5”) flue pipe

VERTICAL REAR FLUE ADAPTOR

Plan View

Front View Side View Rear View

High Leg ModelStore Stand Model

HAVEN PARTS LIST

Charnwood Haven Parts List

Issue C

Item Part No.

Description

Item

Part No.

Description

*These items are not shown on the drawing.

# Please specify colour when ordering.

To obtain spare parts please contact your local stockist giving Model, Part No.

and Description. In case of difficulty contact the manufacturer at the address

shown. This drawing is for identification purposes only.

008/DB136

Cook Plate Seal

008/DB005

Fire Door Seal

008/FW29

Door Seal Adhesive

008/DB072

Oven Door Seal

008/DB137

Access Door Seal

006/DB018

Glass

008/DB003

Glass Seal

004/KV23

Glass Retainer

011/DB031

Throat Plate

004/XV30

Brick Bracket

011/DB029S

Brick Set

011/DB034

Left Side Top Brick

010/DB015R

Right Side Fireplate

010/DB015L

Left Side Fireplate

010/DB016

Back Fire Plate

002/DB008

Deepening Bar

002/DB007

Front Fence

002/SY30

Carrier Bar

012/DB077

Idler Rod

012/DB078

Riddler Rod

012/SY33

Mover Bar

002/CG01S5

Fire Bar (Set of 5)

004/DB017

Ashpan

002/DB098

Riddling Boss

012/EZ095

Riddler Handle

008/ST073/4

Hinge Pin (Set of 4)

004/AP025

Spacer

28#

002/AP024

Hinge

29#

003/DB001A

Fire Door Assembly

008/KV13

Left Hand Door Knob

008/KV16

Door Handle

002/AY14

Door Catch

008/FFW008

M12.5 Washer

008/FFW005

M8 Washer

008/FFN001

M12 Half Nut

004/ST008

Tabbed Locking Washer

008/FFW015

Thackery Washer

38#

003/DB002A

Oven Door Assembly

008/DB047

Oven Door Handle

008/FFM091

Door Catch Roller

008/DB071

Door Insulation

004/DB070

Door Back

008/DB073

Thermometer Gasket

008/DB074

Bimetal Thermometer

45#

003/DB004A

Access Door Assembly

008/DB110

Gasket

010/DB020

Air Control Mounting Box

008/DB109

Air Control Gasket

008/DB108

Air Conrol Cover Gasket

010/DB130

Air Control Plate

004/DB115

Air Control Slider

004/BR015

Clicker Retainer

008/ES36/01

Brass Ball Catch

004/DB081

Air Control Heat Shield

004/DB040

Air Control Cover

008/CR048

Spigot

008/CR063

Duct Gasket

004/CR064

Blanking Plate

008/BR052

Felt Washer

004/EZ016

Air Control Rod

008/AY37

Air Control Knob

001/DB010

Firebox

012/DB011

Serial Label

010/DB009

Cook Plate

65#

010/CY65S

Legs Set

66#

010/DB087

Store Stand

010/BU034

Vertical Rear Flue Adaptor

68#

002/PV12B

Flue Collar

008/KS134

Sealing Gasket (Flue)

004/DB090

Oven Assembly

008/DB092

Oven Shelf

010/DB013

Damper Assembly

008/FFP017

Main Oven Striker Pin

010/DB082

Lower Heat Shield Assembly

75#

010/DB080

Heat Shield

76#

010/DB051S

Rear Shelf Kit (Optional Extra)

77#

010/DB056

Flame Guard (Optional Extra)

004/DB094

Baking Tray (Optional Extra)

AJ WELLS & SONS LTD

Bishops Way, Newport, Isle Of Wight PO30 5WS, United Kingdom

A Division of A.J.Wells & Sons Limited Registered In England No. 03809371

CE certificate for compliance with EN13240:2001

EN13240:2001

ROOMHEATERS FIRED BY SOLID FUEL

Model: HAVEN

EC Certificate of conformity no: DB11-CPD-2022

Fuel type: WOOD LOGS

In accordance with Standard: EN13240:2001

Rated space heating thermal output: 6.6kW

Emission of CO in combustion products: 0.04%

Mean flue gas temperature: 154°C

Energy efficiency: 89.9%

Particles 9 mg/m3

Minimum distance to combustible

materials (Single wall flue:)

90° Installation 45° Corner Installation

Side:

Rear:

Above:

In Front of Window:

500

400

750

800

300

750

800

Fulfilled requirements: BStV of the City

of Munich and the City of Regensburg

FBStVO of the City of Aachen and the

City of Düsseldorf 1.and 2. level of 1.

BlmSchV of Germany

CERTIFICATION

EN - PRODUCT FICHE

FR - FICHE DE PRODUIT

IT - SCHEDA PRODOTTO

PL - KARTA PRODUKTU

ErP (EU 2015/1187)

MANUFACTURER

MARQUE

MARCHIO

MARKA Bishops Way, Newport, Isle of Wight PO30 5WS, United Kingdom

A Division of A.J.Wells & Sons Limited Registered in England No. 03809371

MODEL

MODÈLE

MODELLO

MODEL

AIRE 3

AIRE 5

AIRE 7

ARC 5

ARC 7

BAY 5

BAY 5 BX

BAY 5 VL

BEMBRIDGE

C-FOUR BLU

C-FOUR DUO

C-FOUR INSERT

C-FIVE BLU

C-FIVE DUO

C-SIX

C-SIX BLU

C-EIGHT BLU

COUNTRY 4 BLU

COUNTRY 6

COVE 3 BLU

CRANMORE 3

CRANMORE 5

CRANMORE 7

HAVEN

ISLAND I (AP)

ISLAND II (BP)

SKYE 5

SKYE 7

C-FOUR

C-FIVE

C-SEVEN

C-SEVEN BLU

C-EIGHT

COUNTRY 12

COUNTRY 4

COUNTRY 8

COVE 1

COVE 1SR

COVE 2

COVE 2 BLU

COVE 2SR

COVE 3

ISLAND I

ISLAND II

ISLAND II BLU

ISLAND IICT

ISLAND III

ISLAND III BLU

LA10

SLX20

TOR

TOR PICO

EFFICIENCY CLASS

CLASSE D’EFFICACITÉ

CLASSE DI

EFFICIENZA

KLASA

EFEKTYWNOŚCI

A + A

NOMINAL HEAT

OUTPUT TO ROOM

PUISSANCE

THERMIQUE

NOMINALE

POTENZA TERMICA

NOMINALE

NOMINALNA MOC

CIEPLNA

3.7

5.0

7.0

5.0

7.0

5.0

4.8

5.0

5.1

6.7

5.9

8.0

5.0

6.2

12.0

3.7

5.0

7.0

6.6

5.0

8.0

5.0

7.3

4.9

5.0

7.6

7.1

8.3

12.3

4.8

8.6

4.1

4.3

8.3

8.0

8.3

12.3

5.0

8.0

8.4

12.3

11.0

4.8

5.8

8.4

5.2

ENERGY EFFICIENCY

INDEX

INDICE EFFICACITÉ

ÉNERGÉTIQUE

INDICE DI

EFFICIENZA

ENERGETICA

INDEX

EFEKTYWNOŚCI

ENERGETYCZNEJ

115.7

112.8

109.9

108.5

109.9

112.1

107.0

109.9

107.1

109.8

109.9

108.5

112.8

107.7

107.0

115.7

112.8

109.9

121.5

114.3

109.9

115.7

107.0

104.5

100.8

102.5

105.6

104.1

98.4

102.4

106.7

101.9

106.0

99.3

102.7

99.3

104.7

104.0

104.1

105.6

101.8

105.6

102.4

100.8

97.0

105.8

SEASONAL SPACE

EFFICIENCY

EFFICACITÉ

ÉNERGÉTIQUE

SAISONNIÈRE

POUR LE

CHAUFFAGE DES

LOCAUX

EFFICIENZA

ENERGETICA

STAGIONALE DI

RISCALDAMENTO

DI AMBIENTE

SEZONOWA

EFEKTYWNOŚĆ

CIEPLNA

86.0

84.0

82.0

81.0

82.0

63.0

80.0

82.0

80.1

81.9

82.0

81.0

82.0

80.5

80.0

86.0

84.0

82.0

90.0

85.0

84.0

86.0

80.0

78.3

75.7

76.9

79.0

78.0

74.1

76.8

79.8

76.5

79.3

74.7

77.0

74.7

78.4

77.9

78.0

79.0

76.4

79.0

76.8

75.7

73.1

79.2

Comply with the warnings and instructions concerning installation and maintanence in the operating and installation manual supplied with the stove.

your premier dealer

Charnwood Haven Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info