555436
35
Verklein
Vergroot
Pagina terug
1/44
Pagina verder
34
Operation
Motion Detecting Control Panel (continued)
LOCK
The LOCK feature is designed to prevent activation of the garage door opener from remote controls
while still allowing activation from the door control and keyless entry. This feature is useful for added
peace of mind when the home is empty (i.e.vacation).
l
Activate: Pressand hold the LOCK button for 2 seconds.The command LED will flash as long
as the lock feature is activated and your handheld remote control will not operate your door at
this time.
l
Deactivate: Press and hold the LOCK button again for 2 seconds.The command LEDwill stop
flashing and normal operation will resume.
TIMER-TO-CLOSE
DO NOT enable TTC if operating a one-piece door. The TTC can be turned on or offand the time
interval can be adjusted to 1, 5,and 10 minute intervals. Once the TTC has been setand the door is
open, the selected close interval will blink and begin to count down to close the door.
l
Activate: Pressand hold the ON button until one ofthe TTC LEDslight up. Then press the ON
button again to cycle through the time interval options (the corresponding TTC LEDwill light for
each time interval). The garage door opener lightbulbs will blinkasconfirmation.
l
Deactivate: Press and hold the OFF button until all TTC LEDsturn offand a beep is heard from
the motor unit.
l
Temporarily hold door open (suspend TTC): Press and release the HOLD OPEN button. Press
the HOLD OPENbutton again to resume normal TTC operation.
PROGRAM
Any compatible remote controls,wirelesskeyless entry, or MyQ
®
accessories can be programmed to the
garage door opener by pressing the Learn button.
ON (TTC)
OFF (TTC)
Command LED
Motion Sensor
Switch
LIGHT
Button
HOLD OPEN
Button(TTC)
Motion
Sensor
Push Bar
1, 5, and
10 Minute
TTC LED
LEARN Button
LOCK Button
Remote Control
Your remote control has been programmed at the factory to operate with your garage door opener.
Older Chamberlain remote controls are NOT compatible, see page 40 for compatible accessories.
Programming can be done through the door control or the learn button the garage door opener.To
program additional accessories refer to the instructions provided with the accessory or visit
www.chamberlain.com.Ifyour vehicle is equipped with a Homelink
®
, you may require an external
adapter depending on the make,model,and year ofyour vehicle. Visit www.homelink.com for additional
information.
TO ADD, REPROGRAM, OR CHANGE A REMOTE CONTROL/KEYLESS ENTRY PIN
USING THE MOTION-DETECTING CONTROL PANEL
1. Press the LEARNbutton on the door control to enter Programming Mode.
2. Press the LEARNbutton again, the LED will flash once.
3. Remote Control:
Press the button on the remote control that you wish to operate your garage door. Keyless
Entry:
Enter a 4-digit personal identification number (PIN) of your choice on the keyless entrykeypad.
Then press the ENTER button.
The garage door opener lights will flash (or two clickswill be heard) when the code has been
programmed. Repeat the stepsfor programming additional remote controls or keyless entrydevices.
The command LED
will flash once.
The command LED will
flash once again.
1
2
OR
PIN
? ? ? ?
3
35

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Chamberlain WD832KEV bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Chamberlain WD832KEV in de taal/talen: Engels als bijlage per email.

De handleiding is 4,72 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info