41023
10
Verklein
Vergroot
Pagina terug
1/247
Pagina verder
E
Digital Camera
EX-P600
User’s Guide
K823PCM1DMX
Thank you for purchasing this CASIO
Product.
Before using it, be sure to read the
precautions contained in this User’s Guide.
Keep the User’s Guide in a safe place for
future reference.
For the most up-to-date information about
this product, visit the official Exilim Website
at http://www.exilim.com/.
B
INTRODUCTION
2
INTRODUCTION
Rechargeable lithium ion
battery (NP-40)
CD-ROM
(CASIO Digital Camera Software)
Card Remote Controller
USB Cable Basic Reference
Camera Strap
AV Cable
Unpacking
Check to make sure that all of the items shown below are included with your camera. If something is missing, contact your
dealer as soon as possible.
Rapid Charger Unit (BC-30L)
(Inlet Type) AC power cord
*
*The shape of the AC power
cord plug varies according to
country or geographic area.
○○○○○○○
Note that the shape of the charger unit depends on the area where you purchased the camera.
Rapid Charger Unit (BC-30L)
(Plug-in Type)
Lithium battery (CR2025)
*
For card remote controller.
INTRODUCTION
3
Contents
2INTRODUCTION
Unpacking .................................................................... 2
Features ..................................................................... 10
Precautions ................................................................ 13
General Precautions 13
Test for proper operation before using the camera! 15
Data Error Precautions 15
Operating conditions 15
Condensation 16
Lens and Phase Differential Sensor 16
Other 16
17 QUICK START GUIDE
First, charge the battery! ............................................ 17
To configure display language and clock settings ..... 19
To record an image .................................................... 20
To view a recorded image .......................................... 20
To delete an image ..................................................... 21
22 GETTING READY
About This Manual ..................................................... 22
General Guide ............................................................ 23
Camera 23
Monitor Screen Contents ........................................... 26
REC mode 26
PLAY mode 30
Changing the Contents of the Monitor Screen 31
Indicator Lamps .......................................................... 33
Attaching the Strap .................................................... 34
Power Requirements ................................................. 34
Using the Rapid Charger Unit 34
To load the battery 38
To remove the battery 39
Power Supply Precautions 42
Using AC Power 45
Turning the Camera On and Off 47
Configuring Power Saving Settings 47
Using the On-screen Menus ...................................... 48
Configuring Display Language and Clock Settings ... 51
To configure display language and clock settings 52
INTRODUCTION
4
73 OTHER RECORDING FUNCTIONS
Selecting the Focus Mode ......................................... 73
Using Auto Focus 74
Using the Macro Mode 76
Using the Infinity Mode 77
Using Manual Focus 77
Using Pan Focus 78
Using Focus Lock 79
Exposure Compensation (EV Shift) ........................... 80
Adjusting White Balance ............................................ 81
Adjusting White Balance Manually 83
Specifying the Exposure Mode .................................. 84
Using Aperture Priority AE 84
Using Shutter Speed Priority AE 85
Setting Exposure Settings Manually 87
Using Manual Assist On-screen Guidance 88
Exposure Mode Recording Precautions 89
Using Auto Exposure Lock (AE Lock) ....................... 89
Using a Continuous Shutter Mode ............................. 91
Using the Normal Speed Continuous Shutter Mode 91
Using the High Speed Continuous Shutter Mode 92
25-shot Stop Action Images
(Using the Multi Continuous Shutter Mode) 93
Continuous Shutter Precautions 94
54 BASIC IMAGE RECORDING
Recording an Image ................................................... 54
Aiming the Camera 54
Recording an Image 55
Recording Precautions 57
About Auto Focus 58
About the REC Mode Monitor Screen 58
Previewing the Last Image Recorded ....................... 59
Deleting an Image on the Preview Screen 59
Orientation Sensor ..................................................... 60
Using the Optical Viewfinder...................................... 61
Using Zoom ................................................................ 62
Optical Zoom 62
Digital Zoom 63
Using the Flash .......................................................... 64
Flash Unit Status 66
Changing the Flash Intensity Setting 66
Flash Precautions 67
Using the Self-timer ................................................... 68
Specifying Image Size and Quality ............................ 70
To specify the image size 70
To specify image quality 71
INTRODUCTION
5
Using Auto Bracketing ................................................ 95
Using Auto Bracketing with Exposure Selected
as the Variable (AE Bracketing) 96
Using Auto Bracketing with White Balance
as the Variable (WB Bracketing) 97
Using Auto Bracketing with the Focus Distance
as the Variable (Focus Bracketing) 98
Using Auto Bracketing with Non-configurable
Variables (Multi Bracketing) 99
Auto Bracketing Precautions 100
Previewing Images Recorded with
High Speed
Continuous Shutter or Auto Bracketing ................... 100
Deleting an Image on the Preview Screen 102
Using the BESTSHOT Mode ................................... 103
Creating Your Own BESTSHOT Setup 104
Combining Shots of Two People into a Single Image
(Coupling Shot) ........................................................ 107
Recording a Subject onto an Existing Background
Image (Pre-shot) ...................................................... 109
Using the Movie Mode .............................................. 111
Recording Audio ........................................................113
Adding Audio to a Snapshot 113
Recording Your Voice 114
REC Mode Camera Settings ....................................116
Specifying ISO Sensitivity 117
Selecting the Auto Focus (AF) Mode 118
Selecting the Metering Mode 119
Using the Filter Function 120
Specifying Outline Sharpness 121
Specifying Color Saturation 121
Specifying Contrast 122
Turning the On-screen Grid On and Off 122
Turning Image Review On and Off 123
Assigning Functions to the [] and [] Keys 123
Specifying Power On Default Settings 124
Resetting the Camera 126
Using the Shortcut Menu ......................................... 127
Using the Card Remote Controller for Recording ... 128
Loading the Battery 128
Before Using the Card Remote Controller
for Recording 129
Using the Card Remote Controller 130
Using an External Flash ........................................... 132
External Flash Unit Requirements 132
Attaching an External Flash Unit 133
Using a Conversion Lens or Filter ........................... 135
Installing a Conversion Lens or Close-up Lens 136
Installing a Filter 137
INTRODUCTION
6
159 DELETING FILES
Deleting a Single File ............................................... 159
Deleting All Files ...................................................... 160
161 FILE MANAGEMENT
Folders ..................................................................... 161
Memory Folders and Files 161
Protecting Files ........................................................ 162
To protect a single file 162
To protect all files in memory 163
Using the FAVORITE Folder .................................... 163
To copy a file to the FAVORITE folder 163
To display a file in the FAVORITE folder 165
To delete a file from the FAVORITE folder 166
To delete all files from the FAVORITE folder 167
168 OTHER SETTINGS
Configuring Sound Settings ..................................... 168
To configure sound settings 168
To set the volume level 169
Specifying an Image for the Startup Screen ........... 169
138 PLAYBACK
Basic Playback Operation ........................................ 138
Playing an Audio Snapshot 139
Zooming the Display Image ..................................... 140
Resizing an Image ................................................... 141
Cropping an Image................................................... 142
Checking the Focus of a Recorded Image .............. 144
Playing a Movie ........................................................ 145
Displaying the 9-image View ................................... 146
Selecting a Specific Image in the 9-image View 147
Displaying the Calendar Screen .............................. 147
Playing a Slide Show ............................................... 148
To specify the slideshow images 150
To specify the slideshow time 151
To set the slideshow interval 151
Rotating the Display Image...................................... 152
Using Image Roulette .............................................. 153
Adding Audio to a Snapshot .................................... 154
To re-record audio 155
Playing Back a Voice Recording File ....................... 156
Displaying Camera Images on a TV Screen ........... 157
Selecting the Video Input System 158
INTRODUCTION
7
Copying Files ........................................................... 186
To copy all the files in built-in memory to a memory card 186
To copy a file from a memory card to built-in memory 187
188 PRINTING IMAGES
DPOF ........................................................................ 189
To configure print settings for a single image 190
To configure print settings for all images 191
Using PictBridge or USB DIRECT-PRINT ............... 192
To print a single image 192
To print a group of images 194
Printing Precautions 196
PRINT Image Matching II ............................................. 196
Exif Print ................................................................... 197
198 VIEWING IMAGES ON A COMPUTER
Using the Camera with a Windows Computer ........ 198
USB Connection Precautions 203
Using the Camera with a Macintosh Computer....... 204
USB Connection Precautions 207
Operations You Can Perform from Your Computer .... 207
Configuring Power Down Image Settings................ 170
Specifying the File Name Serial Number
Generation Method .................................................. 172
Using the Alarm ........................................................ 173
To set an alarm 173
Stopping the Alarm 174
Setting the Clock ...................................................... 174
To select your Home Time zone 174
To set the current time and date 175
Changing the Date Format 176
Using World Time ..................................................... 176
To display the World Time screen 176
To configure World Time settings 177
To configure summer time (DST) settings 178
Changing the Display Language ............................. 179
Changing the USB Port Protocol ............................. 179
Formatting Built-in Memory...................................... 180
182 USING A MEMORY CARD
Using a Memory Card .............................................. 183
To insert a memory card into the camera 183
To remove a memory card from the camera 184
Formatting a Memory Card 184
Memory Card Precautions 185
INTRODUCTION
8
Viewing the Contents of the Read me File 225
Installing an Application 226
Viewing User Documentation (PDF Files) 226
User Registration 227
Exiting the Menu Application 227
Installing Software from the CD-ROM
on a Macintosh .......................................................... 227
Installing Software 227
Viewing User Documentation (PDF Files) 228
230 APPENDIX
Menu Reference ....................................................... 230
Indicator Lamp Reference ....................................... 233
REC mode 233
PLAY mode 234
Rapid Charger Unit 235
Troubleshooting Guide............................................. 236
Display Messages 241
Specifications ........................................................... 242
Using a Memory Card to Transfer Images to a
Computer .................................................................. 208
Memory Data ............................................................ 209
DCF Protocol 209
Memory Directory Structure 209
Image Files Supported by the Camera 211
Built-in Memory and Memory Card Precautions 212
213 USING THE CAMERA WITH A COMPUTER
Using the Album Feature ......................................... 213
Creating an album 213
Selecting an Album Layout 215
Configuring Detailed Album Settings 215
Viewing Album Files 218
Saving an Album 220
To delete an album 221
Installing the Software from the CD-ROM ............... 221
About the bundled CD-ROM (CASIO Digital Camera
Software) 221
Computer System Requirements 223
Installing Software from the CD-ROM
in Windows ............................................................... 224
Getting Started 225
Selecting a Language 225
INTRODUCTION
9
IMPORTANT!
The contents of this manual are subject to change
without notice.
Note that the example screens and product
illustrations shown in this Users Guide may differ
somewhat by the screens and configuration of the
actual camera.
CASIO COMPUTER CO., LTD. assumes no
responsibility for any damage or loss resulting from
the use of this manual.
CASIO COMPUTER CO., LTD. assumes no
responsibility for any loss or claims by third parties
which may arise through the use of the EX-P600.
CASIO COMPUTER CO., LTD. shall not be held
liable for any damages or losses suffered by you or
any third party due to the use of Photo Loader and/or
Photohands.
CASIO COMPUTER CO., LTD. assumes no
responsibility for any damage or loss caused by
deletion of data as a result of malfunction, repairs, or
battery replacement. Be sure to back up all important
data on other media to protect against its loss.
The SD logo is a registered trademark.
Windows, Internet Explorer, and DirectX are
registered trademarks of Microsoft Corporation.
Macintosh is a registered trademark of Apple
Computer, Inc.
MultiMediaCard is a trademark of Infineon
Technologies AG of Germany, and licensed to the
MultiMediaCard Association (MMCA).
Acrobat and Acrobat Reader are trademarks of
Adobe Systems Incorporated.
The USB driver (mass storage) uses Phoenix
Technologies Ltd. software.
Compatibility Software Copyright
C
1997
Phoenix Technologies Ltd., All Rights Reserved.
Other company, product and service names used
herein may also be trademarks or service marks of
others.
Photo Loader and Photohands are the property of
CASIO COMPUTER CO., LTD. Except as stipulated
above, all copyrights and other related rights to these
applications revert to CASIO COMPUTER CO., LTD.
Copyright Restrictions
Except for the purposes of your own personal enjoyment,
unauthorized copying of snapshot files, movie files, and
audio files violates copyright laws and international
contracts.
Distribution to third parties of such files over the Internet
without permission of the copyright holder, whether for
profit or for free, violates copyright laws and international
contracts.
INTRODUCTION
10
Features
6 million effective pixels
CCD provides 6.37 million total pixels of very high-
resolution that produces crisp, clear, prints and display
images.
2.0-inch TFT color LCD monitor screen
Long battery life
The cameras low-power design combines with a large-
capacity battery to provide more recording and playback
between charges.
16X seamless zoom (page 62)
4X optical zoom, 4X digital zoom
9.2MB Flash memory
Images can be recorded without using a memory card.
High-speed, high-precision Auto Focus
A phase differentical sensor combines with contrast Auto
Focus for faster focusing.
Three continuous shutter modes (page 91)
In addition to normal continuous shutter operation that
can continually record shots as long as memory is
available, you can also use high-speed continuous
shutter and stop-action continuous shutter, which records
a series of shots in a single image.
Four auto bracketing modes (page 95)
Configurable variables can be set up to record multiple
versions of an image altering the exposure, white
balance, or focus distance setting. Non-configurable
variables create multiple versions of the same image
using various filters and other settings.
Ex Finder view (page 29)
The Ex Finder view provides you with a wealth of
information on the monitor screen as you compose your
images.
Ex Menu (page 127)
Short-cut menu access to four frequently-used settings.
Multi Auto Focus (page 75)
When Multi is selected for the Auto Focus area, the
camera takes simultaneous meter readings at seven
different points and automatically selects the best one.
This makes it possible to avoid erroneous focusing on the
background, and ensure proper focus for a wide range of
image types.
Movable Auto Focus (AF) Area (page 75)
You can move the focus area to the location you want.
Support for SD memory cards and MMC (MultiMedia
Cards) for memory expansion (page 182)
INTRODUCTION
11
Manual Assist (page 88)
Follow the on-screen guidance when configuring manual
exposure settings.
AE Lock (page 89)
A simple operation locks exposure on a particular subject,
helping to ensure that the image is focused the way you
want.
BESTSHOT (page 103)
Simply select the sample scene that matches the type of
image you are trying to record and the camera performs
troublesome setups automatically for beautiful pictures
every time.
Coupling Shot and Pre-shot (pages 107, 109)
Coupling Shot lets you combine two subjects into a single
image, while Pre-shot lets you add a subject to a
previously recorded background image. This means you
can create images that include you and your friend, even
if you are the only two people around.
Triple Self-timer mode (page 68)
The self-timer can be set up to repeat three times,
automatically.
Real-time RGB histogram (page 32)
An on-screen histogram lets you adjust exposure as you
view the effect on overall image brightness, which makes
shooting under difficult lighting conditions easier than
ever before.
World Time (page 176)
A simple operation sets the current time for your current
location. You can select from among 162 cities in 32 time
zones.
Alarm (page 173)
A built-in alarm helps to keep you on time for important
events, and even can be used in place of an alarm clock.
You can also have a specific image appear, or a movie or
audio file to play when the alarm time is reached.
Album Function (page 213)
HTML files are generated automatically to create an
album of recorded images. Album contents can be viewed
and printed using a standard Web browser. Images can
also be incorporated into Web pages quickly and easily.
Calendar screen (page 147)
A simple operation displays a full-month calendar on the
cameras monitor screen. Each day of the full-month
calendar shows a thumbnail of the first image recorded
for that date, which helps to make searching for a
particular image quicker and easier.
Snapshot + Audio Mode (page 113)
Adds audio to a snapshot.
Movie + Audio Mode (page 111)
INTRODUCTION
12
Voice Recording (page 114)
Quick and easy recording of voice input.
After Recording (page 154)
Adds audio to images after they are recorded.
Selectable Sound Settings (page 168)
You can configure different sounds to play whenever you
turn on the camera, press the shutter button half-way or
all the way, or perform a key operation.
Card remote controller (page 128)
External flash connectability (page 132)
Conversion lens/close-up lens support (page 135)
Conversion lens enhances telephoto and wide angle
shots, while the close-up lens enhances macro shots.
DCF Data Storage
DCF (Design rule for Camera File system) data storage
protocol provides image inter-compatibility between the
digital camera and printers.
Digital Print Order Format (DPOF) (page 189)
Images can be printed easily in the sequence you want
using a DPOF compatible printer. DPOF can also be used
when specifying images and quantities for printing by
professional print services.
PRINT Image Matching II Compatible (page 196)
Images include PRINT Image Matching II data (mode
setting and other camera setup information). A printer that
supports PRINT Image Matching II reads this data and
adjusts the printed image accordingly, so your images
come out just the way you intended when you recorded
them.
USB DIRECT-PRINT support (page 192)
Your camera supports USB DIRECT-PRINT, which was
developed by Seiko Epson Corporation. When connected
directly to a printer that supports USB DIRECT-PRINT,
you can select images to print and start the print
operation directly from the camera.
PictBridge support (page 192)
Your camera supports the PictBridge standard of the
Camera and Imaging Products Association (CIPA). You
can connect the camera directly to a printer that supports
PictBridge, and perform image selection and printing
using the camera monitor screen and controls.
Transfer images to a computer simply by connecting the
camera with a USB cable (page 198).
Connect the camera to a TV with the AV cable and use
the TV screen for image recording and viewing (page
157).
INTRODUCTION
13
Precautions
General Precautions
Be sure to observe the following important precautions
whenever using the EX-P600.
All references in this manual to this camera and the
camera refer to the CASIO EX-P600 Digital Camera.
Never try to take pictures or use the built-in display while
operating a motor vehicle or while walking. Doing so
creates the danger of serious accident.
Never try to open the case of the camera or attempt your
own repairs. High-voltage internal components create the
risk of electric shock when exposed. Always leave
maintenance and repair work up to a CASIO authorized
service center.
Never look at the sun or any other bright light through the
cameras viewfinder. Doing so can damage your eyesight.
Keep the small parts and accessories of this camera out
of the reach of small children. If swallowed accidentally,
contact your physician immediately.
Never fire the flash in the direction of a person operating
a motor vehicle. Doing so can interfere with the drivers
vision and create the danger of accident.
Bundled with Photo Loader and Photohands (page 222)
Your camera comes bundled with Photo Loader, the
popular application that automatically loads images from
your camera to your PC. It also comes with Photohands,
and application that makes image retouching quick and
easy.
INTRODUCTION
14
Never use the AC adaptor to power any other device
besides this camera. Never use any other AC adaptor
besides the one that comes with this camera.
Never cover the AC adaptor with a quilt, blanket, or other
cover while it is in use, and do not use it near a heater.
At least once a year, unplug the AC adaptor power cord
from the power outlet and clean the area around the
prongs of the plug. Dust build up around the prongs can
create the danger of fire.
If the cameras case should ever become cracked due to
dropping it or otherwise subjecting it to rough treatment,
immediately turn it off. Next, remove the cameras battery
and/or unplug the AC adaptor power cord from the power
outlet, and contact your dealer or nearest CASIO
authorized service center.
Never use the camera inside of an aircraft or in any other
areas where its use is prohibited. Doing so can result in
an accident.
Physical damage and malfunction of this camera can
cause the data stored in its memory to be deleted. Be
sure to always keep backup copies of data by transferring
them to personal computer memory.
Never open the battery compartment cover, disconnect
the AC adaptor from the camera, or unplug the AC
adaptor from the wall socket while recording images.
Doing so will not only make storage of the current image
impossible, it can also corrupt other image data already
stored in file memory.
Never fire the flash while it is too close to the subjects
eyes. Intense light from the flash can cause eye damage
if it is fired too close to the eyes. This is especially true
with young children. When using the flash, the camera
should be at least one meter (3.3´) from the eyes of the
subject.
Keep the camera away from water and other liquids, and
never let it get wet. Moisture creates the danger of fire
and electric shock. Never use the camera outdoors in the
rain or snow, at the seashore or beach, in the bathroom,
etc.
Should foreign matter or water ever get into the camera,
immediately turn it off. Next, remove the cameras battery
and/or unplug the AC adaptor power cord from the power
outlet, and contact your dealer or nearest CASIO
authorized service center. Using the camera under these
conditions creates the danger of fire and electric shock.
Should you ever notice smoke or a strange odor coming
out of the camera, immediately turn it off. Next, taking
care you do not burn your fingers, remove the cameras
battery and/or unplug the AC adaptor power cord from the
power outlet, and contact your dealer or nearest CASIO
authorized service center. Using the camera under these
conditions creates the danger of fire and electric shock.
After making sure there is no more smoke coming from
the camera, take it to your nearest CASIO authorized
service center for repair. Never attempt your own
maintenance.
INTRODUCTION
15
Operating conditions
This camera is designed for use in temperatures ranging
from 0°C to 40°C (32°F to 104°F).
Do not use or keep the camera in the following areas.
In areas subject to direct sunlight
In areas subject to high humidity or dust
Near air conditioners, heaters, or other areas subject
to temperature extremes
Inside of a closed vehicle, especially one parked in the
sun
In areas subject to strong vibration
Test for proper operation before using
the camera!
Before using the camera to record important images,
make sure you first record a number of test images and
check the results to ensure that the camera is configured
correctly and operating properly (page 20).
Data Error Precautions
Your digital camera is manufactured using precision
digital components. Any of the following creates the risk
of corruption of data in file memory.
Removing the battery or memory card while the
camera is performing a record or memory access
operation
Removing the battery or memory card while the
operation lamp is still flashing after you turn off the
camera
Disconnecting the USB cable while a data
communication operation is being performed
Low battery power
Other abnormal operations
Any of the above conditions can cause an error message to
appear on the monitor screen (page 241). Follow the
instructions provided by the message to eliminate the
cause of the error.
INTRODUCTION
16
Lens and Phase Differential Sensor
Never apply too much force when cleaning the surface of
the lens and phase differential sensor. Doing so can
scratch the lens and phase differential sensor surface and
cause malfunction.
Fingerprints, dust, or any other soiling of the lens and
phase differential sensor can interfere with proper image
recording. Never touch the lens and phase differential
sensor with your fingers. You can remove dust particles
from the lens and phase differential sensor surface by
using a lens blower to blow them off. Next, wipe the
surface of the lens and phase differential sensor with a
soft lens cloth.
When aiming the camera, make sure that your finger
does not block the phase differential sensor.
Other
The camera may become slightly warm during use. This
does not indicate malfunction.
If the exterior of the camera needs cleaning, wipe it with a
soft, dry cloth.
Condensation
When you bring the camera indoors on a cold day or
otherwise expose it to a sudden change of temperature,
there is the possibility that condensation can form on the
exterior or on interior components. Condensation can
cause malfunction of the camera, so you should avoid
exposing it to conditions that might cause condensation.
To keep condensation from forming, place the camera
into a plastic bag before moving it into a location that is
much warmer or colder than your current location. Leave
it in the plastic bag until the air inside the bag has a
chance to reach the same temperature as the new
location. If condensation does form, remove the battery
from the camera and leave the battery compartment
cover open for a few hours.
QUICK START GUIDE
17
QUICK START GUIDE
Plug-in Type
[CHARGE] lamp lights red
during charging.
[CHARGE] lamp turns
green when charging is
complete.
[CHARGE] lamp lights
red during charging.
[CHARGE] lamp turns
green when charging
is complete.
1
2
2
1
Inlet Type
1.
Charge the rechargeable litium ion battery (NP-40)
that comes with the camera (page 35).
Note that the shape of the charger unit depends on the area
where you purchased the camera.
It takes about two hours to achieve a full charge.
First, charge the battery!
QUICK START GUIDE
18
2.
Load the battery (page 38).
1
2
3
Stopper
QUICK START GUIDE
19
1.
Press the power button to turn on the camera.
2.
Press [] to select the language you want.
3.
Press [SET] to register the language setting.
4.
Use [], [], [], and [] to select the geographical
area you want, and then press [SET].
5.
Use [] and [] to select the city you want, and then
press [SET].
6.
Use [] and [] to select the summer time (DST)
setting you want, and then press [SET].
7.
Use [] and [] to select the date format setting you
want, and then press [SET].
8.
Set the date and the time.
9.
Press [SET] to register the clock settings and exit the
setting screen.
1
2, 3, 4, 5, 6, 7, 8, 9
To configure display language and clock settings
Be sure to configure the following settings
before using the camera to record images.
(See page 51 for details.)
QUICK START GUIDE
20
1.
Press the power button to turn on the
camera.
2.
Align the mode dial with (PLAY
Mode).
3.
Use [] and [] to scroll through the
images.
2
1
3
To view a recorded image
(See page 138 for details.)
1.
Press the power button to turn on the camera.
2.
Align the mode dial with (Snapshot Mode).
3.
Point the camera at the subject, use the monitor
screen or viewfinder to compose the image, and
then press the shutter button half way.
When proper focus is achieved, the focus frame turns green
and the green operation lamp lights.
4.
Holding the camera still, gently press the shutter
button.
To record an image
(See page 54 for details.)
1
3
4
2
1200N
1200N
1600
1600
10
10
04/
04/
12
12
/24
24
12
12
:58
58
IN
ISO100
ISO100
F2.8
F2.8
1/1000
1/1000
Green
operation lamp
Focus frame
QUICK START GUIDE
21
1.
Press the power button to turn on the camera.
2.
Align the mode dial with (PLAY Mode).
3.
Press [EX ].
4.
Use [] and [] to display the image you want to delete.
5.
Use [] and [] to select “Delete”.
To exit the image delete operation without deleting anything, select
Cancel.
6.
Press [SET] to delete the image.
To delete an image
(See page 159 for details.)
4, 5, 6
1
3
2
GETTING READY
22
GETTING READY
This section contains information about things you need to
know about and do before trying to use the camera.
About This Manual
This section contains information about the conventions
used in this manual.
Terminology
The following table defines the terminology used in this
manual.
Button Operations
Button operations are indicated by the button name inside
of brackets ([ ]).
On-screen Text
On-screen text is always enclosed by double quotation
marks ( ).
File Memory
The term file memory in this manual is a general term that
refers to the location where your camera is currently storing
the images you record. File memory can be any one of the
following three locations.
The cameras built-in Flash memory
An SD memory card loaded in the camera
A MultiMediaCard loaded in the camera
For more information about how the camera stores images,
see page 161.
This term as used in
this manual:
this camera or the
camera
file memory
battery
charger unit
Means this:
The CASIO EX-P600 Digital
Camera
The location where the camera
is currently storing images you
record (page 55)
The NP-40 Rechargeable
Lithium Ion Battery
The CASIO BC-30L rapid
Charger Unit
GETTING READY
23
8
5
9
0
234
A
1
6
7
Front
General Guide
The following illustrations show the names of each component, button, and switch on the camera.
Camera
1Zoom controller
2Shutter button
3Power button
4Self-timer lamp
5Remote control signal receiver
6Speaker
7External flash sync terminal
8Lens
9Phase differential sensor
0Microphone
AFlash
B[DC IN](AC adaptor connector)
C[USB/AV](USB/AV port)
DTerminal panel cover
Open Terminal Panel Cover
B
C
D
GETTING READY
24
E Viewfinder
F Operation lamp
G [ ](Focus) button
H [ ] (Flash / Calendar) button
I Mode dial
: PLAY Mode
: Snapshot Mode
: BESTSHOT Mode
A : Aperture Priority AE Mode
S : Shutter Speed Priority AE Mode
M : Manual Exposure Mode
: Movie Mode
: Voice Recording Mode
J [MENU] button
K Strap ring
L [ ](Self-timer / Remote Controller)
button
M [PREVIEW] button
N [SET] button
O [][][][]
P [DISP] button
Q Monitor Screen
Back
E
J
I
K
L
M
O
P
Q
R
S
T
N
GH
F
REC Mode
R [EX ] (EX/Delete) button
S [AE-L](AE Lock) button
T [ BKT] (Continuous Shutter/Auto
Bracketing) button
GETTING READY
25
VU
UBattery compartment cover
VTripod screw hole
*Use this hole when attaching to a tripod.
Bottom
WStopper
XBattery compartment
YMemory card slot
X
Y
W
GETTING READY
26
Monitor Screen Contents
The monitor screen uses various indicators and icons to keep you informed of the cameras status.
Note that the example screens in this chapter are for illustrative purposes only. They do not exactly match the screen
contents actually produced on the camera.
REC mode
1Flash mode indicator
None (Auto)
(Flash Off)
(Flash On)
(Red Eye Reduction)
If the camera detects that
flash is required while auto
flash is selected, the flash on
indicator will appear when
the shutter button is pressed
half way.
2Focus mode indicator
None (Auto Focus)
(Macro)
(Pan Focus)
(Infinity)
(Manual Focus)
(Pan Focus) appears in
the Movie Mode only.
5Self-timer/Remote
controller mode
None (1 Shot)
10
s
(10-second Self-timer)
2
s
(2-second Self-timer)
x3(Triple Self-timer)
(Remote controller)
2s
(Remote controller and
2-second Self-timer)
6Recording mode
(Snapshot)
(BESTSHOT)
(Aperture Priority AE)
(
Shutter Speed Priority
AE
)
(Manual Exposure)
(Movie)
(Voice Record)
3White balance indicator
None (Auto)
(Daylight)
(Cloudy)
(Shade)
(Tungsten)
1(Fluorescent 1)
2(Fluorescent 2)
(Flash)
(Manual)
4Continuous shutter/auto
bracketing mode
(Single Shot)
(High Speed Continuous)
(Normal Speed
Continuous)
(Multi Continuous)
AEB
(AE Bracketing)
WBB
(WB Bracketing)
AFB
(Focus Bracketing)
(Multi Bracketing)
5678
B
C
D
3421 9
0
A
GETTING READY
27
7Metering mode indicator
(Multi)
(Center Weighted)
(Spot)
8Image size
2816҂2112 pixels
2816 ҂1872 (3:2) pixels
2048 ҂1536 pixels
1600 ҂1200 pixels
1280 ҂960 pixels
640 ҂480 pixels
Movie Recording: recording time
9Memory Capacity
(Remaining number of storable images)
Movie Recording: Remaining
recording time
0Image quality
F : FINE
N : NORMAL
E : ECONOMY
T : TIFF
AMemory indicator
(Built-in memory in use)
(Memory card in use)
BDate/time
CBattery level indicator
DFocus frame
Focused: Green
Unfocused: Red
F
G
E
EDigital zoom indicator
FISO sensitivity
GAperture value
HShutter speed value
An out of range aperture or shutter speed causes the corresponding
monitor screen value to turn amber.
IZoom indicator
Left side indicates optical zoom.
Right side indicates digital zoom.
I
H
GETTING READY
28
Exposure Panel
The exposure panel is an area in the lower right corner of
the REC mode monitor screen that shows various
adjustable parameters. You can also use the exposure
panel to adjust exposure settings.
2Shutter speed
Use this item to adjust the shutter
speed.
Applicable Modes: S Mode (shutter
priority AE), M Mode (manual
exposure)
3EV shift (exposure compensation value)
Use this item to adjust the exposure
compensation (EV shift) value.
Applicable Mode: Snapshot Mode,
BESTSHOT Mode, A Mode (aperture
priority AE), S Mode (shutter speed
priority AE)
4Manual Focus (MF) setting
Use this item for adjust focus manually.
Applicable Mode: Manual Mode
Exposure Panel
The following explains the items that appear on the
exposure panel. Note that the current recording mode
determines which items appear.
1Aperture value
Use this item to adjust the aperture.
Applicable Modes: A Mode (aperture
priority AE), M Mode (manual
exposure)
Aperture value
Shutter speed
EV shift
MF setting
GETTING READY
29
Ex Finder View
1Focus distance scale
This scale indicates the focus distance range. Note
that this scale is not intended for precision
measurement. It is provided as a general guide only.
The focus distance scale may not appear when any
one of the following conditions exists.
When “Contrast” is selected as the Auto Focus (AF)
mode (page 118)
When “Hybrid” is selected as the Auto Focus (AF)
mode (page 118) and Macro “ ” is selected as the
focus mode (page 73)
Conditions that are so dark or so bright that distance
measurement is impossible
When “Free” is selected as the Auto Focus Area (AF
Area) mode (page 75)
2Focal distance
3White balance indicator
4Flash mode indicator
5Focus mode indicator
6ISO sensitivity
7Manual focus icon
This icon is displayed only when “MF (Manual Focus)”
is selected as the focus mode.
If you use [] and [] to move the cursor to “ ” and
then press [] or [], the Ex Finder view will
disappear and the manual focus indicator (page 77)
will appear.
8Color change icon
You can use [] and [] to move the cursor to “
and then press [] or [] to change the color of the Ex
Finder view.
9Aperture value
0Shutter speed
The shutter speed and aperture values on the
monitor screen will turn amber when you press the
shutter button half way if the image is over-exposed
or under-exposed.
AEV shift (exposure compensation value)
BHistogram (page 32)
A
1
4
7
3
56
8
9
0
B
2
GETTING READY
30
PLAY mode
6Image size
2816 ҂2112 pixels
2816 ҂1872 (3:2) pixels
2048 ҂1536 pixels
1600 ҂1200 pixels
1280 ҂960 pixels
640 ҂480 pixels
Movie Playback: Elapsed play time
7Date and time
8Battery capacity
IMPORTANT!
Some information may not
display properly if you display an
image that was recorded using a
different digital camera model.
12
6
4
5
3
7
8
1PLAY mode file type
Snapshot
Movie
Audio Snapshot
Voice Recording
2Image protection indicator
3Folder number/File number
4Quality
F : FINE
N : NORMAL
E : ECONOMY
T : TIFF
5Built-in memory selected for data
storage.
Memory card selected for data storage.
GETTING READY
31
Indicators on (page 26)
Ex Finder view on (page 29)
Indicators off
Monitor screen off
Changing the Contents of the Monitor
Screen
Each press of the [DISP] button cycles the contents of the
monitor screen as shown below.
IMPORTANT!
The Ex Finder view cannot be displayed in the Movie
mode. In this case, a histogram is displayed in
addition to normal display indicators.
The Ex Finder view cannot be displayed in the
following modes: PLAY, Coupling Shot, Pre-shot.
You cannot turn off the monitor screen in the following
modes: PLAY, BESTSHOT, Movie (standby).
Pressing [DISP] will not change monitor screen
contents during movie recording or during standby or
recording of an audio snapshot.
The only display options that appear when you press
[DISP] in the Coupling Shot or Voice Recording
mode are Indicators on and Monitor screen off.
GETTING READY
32
Histogram
The histogram lets you check exposure conditions as you
record images. You can also display the histogram of a
recorded image in the PLAY mode.
A histogram is a graph that represents the lightness of an
image in terms of the number of pixels. The vertical axis
indicates the number of pixels, while the horizontal axis
indicates lightness. You can use the histogram to
determine whether an image includes the shadowing (left
side), mid tones (center), and highlighting (right) required
to bring out sufficient image detail. If the histogram
appears too lopsided for some reason, you can use EV
shift (exposure compensation) to move it left or right in
order to achieve better balance. Optimum exposure can
be achieved by correcting exposure so the graph is as
close to the center as possible.
When the histogram is too far
to the left, it means that there
are too many dark pixels.
This type of histogram results
when the overall image is
dark. A histogram that is too
far to the left may result in
black out of the dark areas
of an image.
When the histogram is too far
to the right, it means that
there are too many light
pixels.
This type of histogram results
when the overall image is
light. A histogram that is too
far to the right may result in
white out of the light areas of
an image.
A centered histogram
indicates that there is good
distribution of light pixels and
dark pixels. This type of
histogram results when the
overall image is at optimal
lightness.
GETTING READY
33
IMPORTANT!
Note that the above histograms are shown for
illustrative purposes only. You may not be able to
achieve exactly the same shapes for particular
subjects.
A centered histogram does not necessarily
guarantee optimum exposure. The recorded image
may be over-exposed or under-exposed, even
though its histogram is centered.
You may not be able to achieve an optimum
histogram configuration due to the limitations of EV
shift.
Use of the flash as well as certain shooting
conditions can cause the histogram to indicate
exposure that is different from the actual exposure of
the image when it was recorded.
Indicator Lamps
You can find out the operational status of the camera at a
glance by checking the color of the indicator lamps, and
whether a lamp is lit or flashing. For details, see Indicator
Lamp Reference on page 233.
Self-timer lamp
Green operation lamp
Red operation lamp
GETTING READY
34
Attaching the Strap
Attach the strap to the strap ring as shown in the
illustration.
IMPORTANT!
To avoid dropping the camera while operating it, be
sure to wear the strap around your wrist. Use the
buckle to ensure that the strap is fastened snugly
your wrist.
The supplied strap is intended for use with this
camera only. Do not use it for any other purpose.
Never swing the camera around by the strap.
Power Requirements
Your camera can operate on either battery power or AC
power.
Battery
One NP-40 rechargeable lithium ion battery
The battery is not charged when you purchase the
camera. You need to charge the battery before using
the camera for the first time (page 35).
Household AC Power
AC Adaptor: AD-C40 (Option)
Using the Rapid Charger Unit
Rapid Charger Unit General Guide
Contacts
[CHARGE]
lamp
GETTING READY
35
Attaching the Battery to the Rapid Charger Unit
Making sure that the positive and negative contacts are
aligned correctly, affix the battery to the charger unit. Note
that the battery will not charge properly if it is not positioned
correctly on the charger unit.
+
-
T
To charge the battery
1.
Correctly positioning the positive and
negative terminals of the battery, attach the
battery to the charger unit.
○○○○○○○○○○○○○○○○○○
Plug-in TypeInlet Type
GETTING READY
36
2.
Plug the charger unit into a household power
outlet.
This will cause the [CHARGE] lamp to turn red.
Charging will take about two hours.
Note that the shape of the charger unit depends on
the area where you purchased the camera.
NOTE
The bundled charger unit is designed for operation
with any power supply in the range of 100V to 240V
AC. Note, however, that the shape of the AC power
cord plug varies according to country or geographic
area. If you plan to use the charger unit in a
geographic area where the power receptacle shape
is different from that in your area, replace the AC
power cord with one of the other ones that comes
with the camera, or purchase a commercially
available AC power cord that is compatible with the
power outlets in that area.
○○○○○○○○○○○○○○○○○○○○○○○○○○○
[CHARGE] lamp
Plug
Charger unit
AC power cord
[CHARGE] lamp
Charger unit
GETTING READY
37
NOTE
The bundled charger unit is designed for operation on
power ranging from 100V AC to 240V AC. Note,
however, that the shape of the power plug varies
according to country or geographic area. When
traveling abroad, it is up to you to find out if the shape
of the charger unit power plug is compatible with local
power outlets and to purchase any required adapters.
3.
The [CHARGE] lamp turns green when
charging is complete.
4.
After charging is complete, unplug the
charger unit from the power outlet, and
remove the battery from it.
Always unplug the charger unit from the power outlet
and remove the battery whenever you are not using
it for charging.
IMPORTANT!
If the battery or charger unit is very hot or cold when
you start charging or if it becomes hot during charging,
the charger unit will enter a standby state, which is
indicated when its [CHARGE] lamp is lit amber.
Charging will resume when the temperature returns to
the allowable charging temperature range, which is
indicated when the [CHARGE] lamp turns red.
Charging battery while it is still warm immediately
after removing it from the camera can result in only
partial charging. Give battery time to cool before
charging it.
Battery discharges slightly even when it is left
without loading it into the camera. Because of this, it
is recommended that you charge battery immediately
before you need to use it.
The rechargeable battery used with this camera is
specifically designed for use with digital cameras. If
you want to try to use it to power another type of
device, you should first check the user
documentation that comes with the device to see if it
is compatible.
Though the actual service life of the rechargeable
battery depends on the environment under which it is
used, you can expect to be able to recharge it about
500 times before it needs replacement.
Charging the cameras battery may cause
interference with TV and radio reception. If this
happens, plug the charger into an outlet that is
further away from the TV or radio.
Dirty charger contacts and/or battery terminals can
make proper charging impossible. Be sure to wipe
contacts and terminals occasionally with a dry cloth
to keep them clean.
GETTING READY
38
2.
While pulling the stopper in the direction
indicated by the arrow in the illustration, align
the (–) mark on the battery with the (–) mark
on the camera and slide the battery into the
camera.
Push the bottom of
the battery, and
make sure that the
stopper securely
locks the battery in
place.
() marks
NP-40
Stopper
To load the battery
1.
While pressing the battery compartment
cover on the bottom of the camera, slide the
cover in the direction indicated by the arrow,
and then swing it open.
GETTING READY
39
3.
Swing the battery compartment cover closed,
and then slide it in the direction indicated by
the arrow.
IMPORTANT!
Use only the special NP-40 rechargeable lithium ion
battery to power this camera. Use of any other type
of battery is not supported.
To remove the battery
1.
Open the battery compartment cover.
2.
Pull the stopper in the direction indicated by
the arrow.
This will cause the battery to come part way out of
the slot.
Stopper
3.
Release the stopper and pull the battery from
the camera.
Take care so you do not drop the battery.
GETTING READY
40
If the camera works normally
1.
Continue using the camera until the current
charge is used up, and then charge the
battery.
If the camera does not work normally
This can mean there is a problem with how the battery is
loaded.
1.
Remove the battery from the camera and
check the battery contacts for dirt. If the
contacts are dirty, wipe them clean with a dry
cloth.
Battery Life Guidelines
The battery life guideline values given below indicate the
amount of time under the conditions defined below the
table, until power automatically turns off due to battery
failure. They do not guarantee that the battery will provide
the amount of service indicated. Low temperatures and
continued use reduce battery life.
Apporoximate Battery Life
260 shots (130 minutes)
600 shots (150 minutes)
300 minutes
260 minutes
Operation
Number of Shots (CIPA)*1
(Operating Time)
Number of Shots, Continuous
Recording*2 (Operating Time)
Continuous Playback*3
(Continuous Snapshot Recording)
Continuous Voice Recording*4
GETTING READY
41
The above values are based on a new battery starting
from a full charge. Repeated charging shortens battery
life.
Battery life is greatly affected by how much you use flash,
zoom and other functions, and how long you leave power
turned on.
Tip to Make the Battery Last Longer
If you do not need the flash while recording, select
(flash off) for the flash mode. See page 64 for more
information.
You can also conserve battery power by using the [DISP]
button to turn off the monitor screen.
Supported Battery: NP-40 (Rated Capacitance: 1230mAh)
Storage Medium: SD Memory Card
*1 Number of Shots (CIPA)
CIPA Standard
Temperature: 23°C (73°F)
Monitor Screen: On
Zoom operation between full wide to full telephoto
every 30 seconds, during which two images are
recorded, one image with flash; power turned off and
back on every time 10 images are recorded.
*2 Continuous Recording Conditions
Temperature: 23°C (73°F)
Monitor screen: On
Flash: Off
Image recorded approximately every 15 seconds
*3 Continuous Playback Conditions
Temperature: 23°C (73°F)
Scroll one image about every 10 seconds
*4 Voice recording times are based on continuous
recording.
GETTING READY
42
Low Battery Indicator
The following shows how the battery capacity indicator on
the monitor screen changes as battery power is used. The
indicator means that remaining battery power is low.
Note that you will not be able to record images while the
battery indicator is . Charge the battery immediately
whenever either of these indicators appears.
Battery Level High Low
Indicator
Power Supply Precautions
Note the following precautions when handling or using the
battery and the charger unit.
Battery Handling Precautions
SAFETY PRECAUTIONS
Be sure to read the following Safety Precautions before
trying to use the battery for the first time. Keep these safety
precautions and all operating instructions on hand for
future reference.
NOTES
The term battery in this manual refers to the CASIO
NP-40 Rechargeable Lithium Ion Battery.
Use only the rapid charger unit (BC-30L) to charge
the special NP-40 rechargeable lithium ion battery.
Never use any other charging device.
GETTING READY
43
Failure to observe any of the following precautions
while using the battery creates the risk of overheating,
fire, and explosion.
Never try to use the battery to power any other
device other than this camera.
Never use or leave the battery near open flame.
Never place the battery in a microwave oven, throw
it into fire, or otherwise expose it to intense heat.
Make sure the battery is oriented correctly when you
load it into the camera or attach it to the charger
unit.
Never carry or store the battery together with items
that can conduct electricity (necklaces, pencil lead,
etc.)
Never try to take the battery apart, modify it in any
way, or expose it to strong impact.
Do not immerse the battery in fresh water or salt
water.
Do not use or leave the battery under direct
sunlight, in an automobile parked in the sun, or in
any other area subject to high temperatures.
Should you ever notice leakage, strange odor, heat
generation, discoloration, deformation, or any other
abnormal condition while using, charging, or storing a
battery, immediately remove it from the camera or
charger unit and keep it away from open flame.
If the battery does not achieve full charge after the
normal charging time has passed, stop charging.
Continued charging creates the risk of overheating, fire,
and explosion.
Battery fluid can damage your eyes. Should battery
fluid get into your eyes accidentally, immediately rinse
them with clean tap water and then consult a physician.
If the battery is to be used by young children, make
sure that a responsible adult makes them aware of the
precautions and proper handling instructions and make
sure that they handle the battery correctly.
Should fluid from the battery accidentally get onto
clothing or your skin, immediately rinse it off with clean
tap water. Prolonged contact with battery fluid can
cause skin irritation.
GETTING READY
44
PRECAUTIONS DURING USE
Charge the battery in a location where the temperature
is in the range of 5°C to 35°C (41°F to 95°F). Charging
outside this temperature range can cause charging to
take longer than normal or even cause charging to fail.
Very limited operation following a full charge indicates
that the battery has reached the end of its service life.
Replace the battery with a new one.
Never wipe the battery with thinner, benzene, alcohol,
or other volatile agents or chemically treated rags.
Doing so can cause deformation of the battery and lead
to malfunction.
This charger unit is intended to be correctly orientated
in a vertical or floor mount position.
BATTERY STORAGE PRECAUTIONS
Make sure you remove the battery when you do not
plan to use the camera for a long time. A battery left in
the camera discharges very small amounts of power
even when power is turned off, which can lead to a
dead battery or the need for longer charging before the
next use.
Store the battery in a cool, dry place (20°C (68 °F) or
lower).
USING THE BATTERY
When transporting a battery, keep it either loaded in
the camera or stored in its case.
GETTING READY
45
Charger Unit Precautions
Never plug the charger unit into an outlet whose
voltage rating is different from that marked on the
charger unit. Doing so creates the risk of fire,
malfunction, and electric shock.
Never plug in or unplug the charger unit while your
hands are wet. Doing so creates the risk of electric
shock.
Do not plug the charger unit into an outlet or extension
cord that is shared by other devices. Doing so creates
the risk of fire, malfunction, and electric shock.
The charger unit becomes slightly warm during
charging. This is normal and does not indicate
malfunction.
Unplug the charger unit from the power outlet
whenever you are not using it.
Using AC Power
You need to purchase the optionally available AC adaptor
(AD-C40) in order to be able to power the camera using AC
power.
1.
Connect the AC power cord to the AC
adaptor.
2.
Open the camera’s terminal panel cover and
connect the AC adaptor to the port marked
[DC IN].
GETTING READY
46
AC Adaptor Precautions
Be sure to turn off power before connecting or
disconnecting the AC adaptor.
Always turn camera power off before disconnecting the
AC adaptor, even if the camera has a battery installed. If
you dont, the camera will turn off automatically when you
disconnect the AC adaptor. You also run the risk of
damaging the camera whenever you disconnect the AC
adaptor without first turning power off.
The AC adaptor may become warm to touch after
extended periods of use. This is normal and is not cause
for alarm.
After using the camera, turn it off and unplug the AC
adaptor from the AC outlet.
The camera automatically switches over to AC adaptor
powered operation whenever the AC adaptor is plugged
into the camera.
Always use the AC adaptor to power the camera
whenever it is connected to a computer.
Never place a blanket or any other cover on the AC
adaptor. Doing so creates the risk of fire.
Plug
Terminal panel
cover
[DC IN]
AC power cord
AC adaptor
3.
Plug the AC power cord into an electrical
outlet.
NOTE
The AC adaptor can be used with any power source
rated from 100V to 240V AC. If you plan to use the
AC adaptor in another country, it is up to you to
purchase the applicable AC power cord that matches
the configuration of power receptacles in that
country.
GETTING READY
47
Turning the Camera On and Off
Press the power button to turn the camera on and off.
Pressing the power button to turn on the camera causes
the green operation lamp to flash. Press the power button
again to turn off the camera.
Green operation lampPower button
IMPORTANT!
If camera power is turned off by the Auto Power Off
feature, press the power button to turn it back on
again.
Turning on camera power while the mode dial is set
to REC mode causes the lens to extend from the
camera. Make sure there is nothing in front of the
camera that can be hit by the lens when you turn on
the camera.
Configuring Power Saving Settings
You can configure the settings described below to
conserve battery power.
Sleep : Automatically turns off the monitor screen
if no operation is performed for a specified
amount of time in the REC mode.
Performing any button operation causes
the monitor screen to turn back on.
Auto Power Off : Turns off power if you do not perform any
operation for a specified amount of time.
1.
Turn on the camera.
2.
Press [MENU].
3.
Use [] and [] to select the “Set Up” tab.
4.
Use [] and [] to select the feature whose
setting you want to configure, and then press
[].
GETTING READY
48
5.
Use [] and [] to change the currently
selected setting, and then press [SET].
Available Sleep settings are: 30 sec, 1 min, 2 min,
and Off.
Available Auto Power Off settings are: 2 min and
5 min.
Note that the Sleep feature does not operate in the
PLAY mode.
Pressing any button while the camera is in the Sleep
state immediately turns the monitor screen back on.
The Auto Power Off and Sleep features are disabled
in the following cases.
While the camera is connected to computer or TV
via its USB/AV port
While a slideshow is in progress
While playing back a voice recording file
While playing back a movie
To configure this feature: Select this setting:
Sleep Sleep
Auto Power Off Auto Power Off
See page 48 for information about how to use
menus. Using the On-screen Menus
Pressing [MENU] displays menus on the monitor screen
that you can use to perform various operations. The menu
that appears depends on whether you are in the REC
mode or the PLAY mode. The following shows an example
menu procedure in the REC mode.
1.
Turn on the camera,
and then align the
mode dial with .
If you want to enter the
PLAY mode instead,
you would align the
mode dial with .
Mode dial
GETTING READY
49
Settings
Selection cursor (indicates the
currently selected item)
Tab
[MENU]
[
][
][
][
]
[SET]
2.
Press [MENU]. Menu Screen Operations
When you want to do this:
Move between tabs
Move from the tab to the
settings
Move from the settings to
the tab
Move between the settings
Display the options
available for a setting
Select an option
Register an option
selection and exit the menu
screen
Register an option
selection and return to the
menu screen
Exit the menu screen
Do this:
Press [] and [].
Press [].
Press [].
Press [] and [].
Press [] or press [SET].
Press [] and [].
Press [SET].
Press [].
Press [MENU].
GETTING READY
50
3.
Press [] or [] to select the tab you want,
and then press [SET] to move the selection
cursor from the tab to the settings.
4.
Use [] and [] to
select the feature
whose setting you
want to configure,
and then press [].
Instead of pressing [],
you could also press
[SET].
5.
Use [] and [] to change the currently
selected setting.
Example: To select the
Size item.
6.
Perform one of the following operations to
apply the setting you configured.
To do this:
Apply the setting and exit
the menu screen.
Apply the setting and
return to feature selection
in step 4.
Apply the setting and
return to tab selection in
step 3.
Perform this key operation:
Press [SET].
Press [].
1. Press [].
2. Use [] to move back up to
tab selection.
See Menu Reference on page 230 for more information
about menus.
GETTING READY
51
Configuring Display Language and Clock
Settings
Be sure to configure the following settings before using the
camera to record images.
Display language
Home city
Date Style
Date and time
Note that the current date and time settings are used by
the camera to generate the date and time that are stored
along with image data, etc.
IMPORTANT!
Recording images without configuring the clock
settings causes incorrect time information to be
registered. Be sure to configure the clock settings
before using the camera.
The cameras clock settings are cleared whenever
power is totally cut off. This can happen if the battery
goes dead while the camera is not being supplied
power by AC adaptor. The clock setting screen will
appear automatically the next time you turn on power
after the settings are cleared. Set the date and time
before using the camera.
The current date and time settings will be cleared if
the battery remains dead without being charged for
about two days.
GETTING READY
52
To configure display language and clock
settings
1.
Press the power button to turn on the camera.
2.
Use [], [], [], and
[] to select the
language you want,
and then press [SET].
: Japanese
English : English
Français : French
Deutsch : German
Español : Spanish
Italiano : Italian
Português : Portuguese
: Chinese (Complex)
: Chinese (Simplified)
: Korean
3.
Use [], [], [], and
[] to select the
geographical area
where you live, and
then press [SET].
4.
Use [] and [] to
select the name of the
city where you live,
and then press [SET].
5.
Use [] and [] to select the summer time
(DST) setting you want, and then press [SET].
When you want to do this:
Keep time using summer time
(Daylight Saving Time)
Keep time using standard time
Select this setting:
On
Off
GETTING READY
53
6.
Use [] and [] to
change the date format
setting, and then press
[SET].
Example: December 24, 2004
Select this format:
YY/MM/DD
DD/MM/YY
MM/DD/YY
To display the date like this:
04/12/24
24/12/04
12/24/04
8.
Press [SET] to register the settings and exit
the setting screen.
To do this:
Change the setting at the current
cursor location
Move the cursor between settings
Toggle between 12-hour and 24-
hour timekeeping
Do this:
Press [] and [].
Press [] and [].
Press [DISP].
7.
Set the current date
and the time.
54
BASIC IMAGE RECORDING
This section describes the basic procedure for recording an
image.
Recording an Image
Aiming the Camera
Use both hands to hold the camera still when shooting an
image. Holding the camera with one hand increases the
chance of movement, which can blur your images.
Horizontal Hold the camera
still in both
hands, with your
arms firmly
against your
sides.
Vertical When holding
the camera
vertically, make
sure that the
flash is above
the lens. Hold
the camera still
with both hands.
IMPORTANT!
Make sure your fingers or the strap does not block
the flash, microphone or lens.
When aiming the camera, take particular care to
ensure that your finger is not blocking the phase
differential sensor.
BASIC IMAGE RECORDING
Flash
Microphone
Lens
Phase differential
sensor
NOTE
Your image will be blurred if you move the camera
when pressing the shutter button. Press the shutter
button carefully, taking care that there is no camera
movement. This is especially important when
available lighting is low, which slows down the
shutter speed.
55
BASIC IMAGE RECORDING
Recording an Image
Your camera automatically adjusts shutter speed and
aperture values in accordance with the brightness of the
subject. Images you record are stored in the camera’s built-
in memory, or to a memory card if you have one loaded in
the camera.
When an optionally available SD memory card or
MultiMediaCard (MMC) is loaded in the camera, images
are stored on the card (page 182).
1.
Press the power
button to turn on the
camera.
This causes an image or
a message to appear on
the monitor screen.
2.
Align the mode dial
with (Snapshot
Mode).
This enters the Snapshot
mode for image
recording.
3.
Compose the image
on the monitor screen
so the main subject is
within the focus
frame.
The focusing range of
the camera in the Auto
Focus mode is
approximately 40cm
(1.3 feet) to infinity ()
(page 74).
You can compose images using either the monitor
screen or the optical viewfinder (page 61).
When using the optical viewfinder to compose
images, you can use the [DISP] button to turn off the
monitor screen and conserve battery power.
1200N
1200N
1600
1600
10
10
04/
04/
12
12
/24
24
12
12
:58
58
IN
ISO100
ISO100
F2.8
F2.8
1/1000
1/1000
Focus frame
Mode dial
Power button
56
BASIC IMAGE RECORDING
BKT
4.
Press the shutter button half
way to focus the image.
When you press the shutter
button half way, the camera’s
Auto Focus feature automatically
focuses the image, and displays
the shutter speed and aperture
values. The ISO sensitivity value
also appears on the display at
this time.
You can tell whether the
image is focused by
observing the focus frame
and the green operation
lamp.
Green operation lamp
It means this:
The image is in focus.
The image is not in focus.
When you see this:
Green focus frame
Green operation lamp
Red focus frame
Flashing green operation lamp
Make sure you are not
blocking the lens, phase
differential sensor, the
flash, or the microphone
with your fingers while
recording an image.
Operation Lamp and Focus Frame Operation
Lens
Flash
Shutter button
Phase differential
sensor
Microphone
57
BASIC IMAGE RECORDING
5.
After making sure that the
image is focused properly,
press the shutter button the
rest of the way down to
record.
The number of images that can
be stored in memory depends on
the image size and image quality
setting you are using (page 70).
Press the shutter button gently to avoid camera
movement.
Shutter button
Recording Precautions
Never open the battery compartment cover while the
green operation lamp is flashing. Doing so not only
causes the current image to be lost, it can also corrupt
images already stored in file memory and even lead to
malfunction of the camera.
Never remove the memory card while an image is being
recorded to the memory card.
Fluorescent lighting actually flickers at a frequency that
cannot be detected by the human eye. When using the
camera indoors under such lighting, you may experience
some brightness or color problems with recorded images.
When “Auto” is selected for the ISO sensitivity setting
(page 117), the camera automatically adjusts its
sensitivity in accordance with the brightness of the
subject. This can cause some static noise to appear in
images of relatively dark subjects.
When recording a dimly lit subject while “Auto” is selected
for the ISO sensitivity setting (page 117), the camera
increases sensitivity and uses a slower shutter speed.
Because of this, you need to guard against camera
movement if you have flash turned off (page 64).
If unwanted light is shining on the lens, shade the lens
with your hand when recording the image.
58
BASIC IMAGE RECORDING
About the REC Mode Monitor Screen
The image shown on the monitor screen in the REC
mode is a simplified image for composing purposes. The
actual image is recorded in accordance with the image
quality setting currently selected on your camera. The
image saved in file memory has much better resolution
and detail than the REC mode monitor screen image.
Certain levels of subject brightness can cause the
response of the REC mode monitor screen to slow down,
which causes some static noise in the monitor screen
image.
About Auto Focus
Auto Focus tends not to work well if the camera is moved
during recording, or when recording the types of subjects
listed below.
Solid color walls or objects with little contrast
Strongly backlit objects
Polished metal or other brightly reflective objects
Venetian blinds or other horizontally repeating patterns
Multiple images that are varying distances from the
camera
Subjects in poorly lit areas
Moving subjects
Note that a green operation lamp and focus frame do not
necessarily guarantee that an image is in focus.
If Auto Focus does not produce the results you want for
some reason, try using focus lock (page 79) or manual
focus (page 77).
59
BASIC IMAGE RECORDING
Previewing the Last Image Recorded
Use the following procedure to preview the last image
recorded, without leaving the current REC mode.
1.
Press [PREVIEW] to
display the last image
recorded.
Pressing [PREVIEW] again
returns to the REC mode
screen.
No preview image will appear if you press
[PREVIEW] after changing the mode dial setting, or
immediately after you turn on the camera.
Image preview cannot be used in the Movie Mode.
The preview image is cleared automatically
whenever the REC mode is changed.
Deleting an Image on the Preview Screen
You can use the preview screen to delete the last image
you recorded.
IMPORTANT!
Note that the image delete operation cannot be
undone. Make sure you really do not need an image
before you delete it.
1.
In the REC mode, press [PREVIEW] to display
the last image you recorded.
2.
Press [EX ].
3.
In response to the confirmation message that
appears, use [] and [] to select “Delete”.
Select “Cancel” to cancel the delete operation
without deleting anything.
4.
Press [SET].
This deletes the image and returns to the REC mode
screen.
[PREVIEW]
60
BASIC IMAGE RECORDING
Orientation Sensor
The camera has an orientation sensor that detects whether
the camera is being held horizontally (its normal
orientation) or vertically when you record an image.
Information about camera orientation is recorded along with
the image data so the image can be displayed properly.
When you transfer images to a computer using the bundled
Photo Loader application (page 222), Photo Loader also
detects the orientation of each image and displays it
accordingly.
20°
20°
IMPORTANT!
To ensure proper operation of the orientation sensor,
note the following points.
Keep the camera still during recording. Moving
the camera while recording can cause miss-
operation of the orientation sensor.
When recording an image using portrait (vertical)
orientation, make sure the camera is standing
straight up, 90 degrees from horizontal. A sensor
error may occur if the camera is angled more than
about 20 degrees from vertical.
When positioning the camera vertically, keep the
flash above the lens.
61
BASIC IMAGE RECORDING
60°
60°
Miss-operation of the orientation sensor can also
occur if the camera is angled towards the front or
back. A sensor error may occur if the camera is
angled more than about 60 degrees towards the
front or back.
Note that the orientation sensor does not operate
in the Movie mode.
Using the Optical Viewfinder
You can conserve battery power by turning off the
camera’s monitor screen (page 31) and using the optical
viewfinder to compose images.
IMPORTANT!
The frame that is visible inside of the viewfinder
indicates the image recorded at a distance of about
one meter (3.3´). When the subject is closer than one
meter, the recorded image will be different from what
you see inside the viewfinder frame.
Since the monitor screen shows exactly what will be
recorded, always use it for composing your images in
the Macro and Manual Focus modes.
BKT
Viewfinder frameShort distance
to subject
Viewfinder
62
BASIC IMAGE RECORDING
Using Zoom
Your camera is equipped with two types of zoom: optical
zoom and digital zoom.
Optical Zoom
The range of the optical zoom factor is shown below.
Optical Zoom Factor Range: 1X to 4X
1.
In the REC mode, shift the
zoom controller to change
the zoom factor.
Zoom out Zoom in
Zoom controller
2.
Compose the image, and then press the
shutter button.
NOTES
The optical zoom factor also affects the lens
aperture.
Use of a tripod is recommended to protect against
hand movement when using the telephoto setting
(zoom in).
Shift this side of the zoom controller:
(Wide Angle)
(Telephoto)
To do this:
Zoom out
Zoom in
63
BASIC IMAGE RECORDING
5.
Slide the zoom
controller towards
(Telephoto)/ to
change the zoom factor.
When zoom reaches
maximum optical zoom,
it stops momentarily.
Keep the zoom
controller pressed to the
(Telephoto)/ side
and zoom will switch
over to digital zoom
automatically.
Switching to digital zoom causes the zoom indicator
to appear on the monitor screen. The zoom indicator
shows the current approximate zoom factor.
6.
Compose the image, and then press the
shutter button.
Digital Zoom
Digital zoom is activated after you reach the maximum
optical zoom factor (4X). It enlarges the part of the image
at the center of the image screen. The range of the digital
zoom factor is shown below.
Digital Zoom Factor Range: 4X to 16X
(in combination with optical
zoom)
1.
In the REC mode, press [MENU].
2.
Use [] and [] to select the “REC” tab.
3.
Use [] and [] to select “Digital Zoom”, and
then press [].
4.
Use [] and [] to select “On”, and then
press [SET].
Selecting “Off” disables digital zoom.
Zoom indicator
Digital zoom indicator
1X 4X 16X
Current zoom factor
Optical Zoom
Digital
Zoom
64
BASIC IMAGE RECORDING
Using the Flash
Perform the following steps to select the flash mode you
want to use.
1.
In the REC mode, press [MENU].
2.
Press [ ] to select the
flash mode.
Each press of [ ] cycles
through the flash mode
settings shown below on the
monitor screen.
Flash mode indicator
IMPORTANT!
Digital zoom is disabled whenever the monitor
screen is turned off (page 31).
Using digital zoom can cause degradation of the
recorded image.
[ ]
65
BASIC IMAGE RECORDING
3.
Record the image.
IMPORTANT!
Image recording may not be performed if you press
the shutter button while the red operation lamp is
flashing.
To do this:
Have the flash fire automatically when
required (Auto Flash)
Turn off the flash (Flash Off)
Always fire the flash (Flash On)
Fire a pre-flash followed by image
recording with flash, reducing the
chance of red-eye in the image (Red-
eye reduction)
In this case, the flash fires automatically
when required
Select this setting:
None
About Red-eye Reduction
Using the flash to record at night or in a dimly lit room can
cause red spots inside the eyes of people who are in the
image. This is caused when the light from the flash reflects
off of the retina of the eye. When red-eye reduction is
selected as the flash mode, the camera performs two pre-
flash operations, one designed to cause the irises in the
eyes of any people in the image to close, and one for the
Auto Focus operation. This is followed by another flash
operation for actual recording of the image.
IMPORTANT!
Note the following important points when using red-
eye reduction.
Red-eye reduction does not work unless the people
in the image are looking directly at the camera during
the pre-flash. Before pressing the shutter button, call
out to the subjects so they all look at the camera
while the pre-flash operation is performed.
Red-eye reduction may not work very well if the
subjects are located far away from the camera.
66
BASIC IMAGE RECORDING
Flash Unit Status
You can find out the current flash unit status by pressing
the shutter button half way and checking the monitor
screen and red operation lamp.
BKT
Red operation lamp
*
The indicator is also
shown on the monitor
screen when the flash unit
is ready to fire.
*Red operation lamp
It means this:
Flash unit is charging
Flash unit is ready to fire
When the red operation
lamp is this:
Flashing
Lit
Changing the Flash Intensity Setting
Perform the following steps to change the flash intensity
setting.
1.
In the REC mode, press [MENU].
2.
Use [] and [] to select the “REC” tab.
3.
Use [] and [] to select “Flash Intensity”,
and then press [].
4.
Use [] and [] to select the setting you
want, and then press [SET].
To do this:
Fire the flash with strong intensity
Fire the flash with normal intensity
Fire the flash with weak intensity
Select this setting:
Strong
Normal
Weak
NOTE
Flash intensity may not change if the subject is too
far or too close to the camera.
67
BASIC IMAGE RECORDING
Flash Precautions
Take care that your fingers do
not block the flash when you
hold the camera. Covering the
flash with your finger can
greatly reduce its
effectiveness.
You may not be able to achieve the desired results using
a flash if the subject is too close or too far away.
The flash takes anywhere from a few seconds to as long
as 10 seconds to attain full charge after being fired. The
actual time required depends on the battery level,
temperature, and other conditions.
The flash does not fire in the Movie mode. This is
indicated by (Flash Off) on the monitor screen.
The flash unit may not be able to charge when battery
power is low. Low battery power is indicated by (Flash
Off) on the monitor screen, and when the flash fails to fire
properly resulting in poor image exposure. When these
symptoms occur, charge the camera’s battery as soon as
possible.
When the red-eye reduction mode ( ) is selected, flash
intensity is adjusted automatically in accordance with the
exposure. The flash may not fire at all when the subject is
brightly lit.
Flash
Using flash in combination with another light source
(daylight, fluorescent light, etc.) can result in abnormal
image colors.
68
BASIC IMAGE RECORDING
Using the Self-timer
The self-timer lets you select either a 2-second or 10-
second delay of the shutter release after you press the
shutter button. A Triple Self-timer feature lets you perform
three consecutive self-timer operations to record three
images.
1.
In the REC mode, use
[ ] to cycle through
the available self-timer
modes.
Each press of [ ]
cycles through the timer
settings on the monitor
screen in the sequence
shown below.
Self-timer setting
With the Triple Self-timer, the camera records a series
of three images in the sequence described below.
1. The camera performs a 10-second countdown
and then records the first image.
2. The camera prepares to record the next image.
The amount of time required for preparation
depends on the camera’s current “Size” and
“Quality” settings, the type of memory (built-in or
card) you are using for image storage, and
whether or not the flash is charging.
To do this:
Disable the self-timer
Specify a 10-second self-timer
Specify a 2-second self-timer
Specify Triple Self-timer
Self-timer off for remote controller
operation (page 129)
2-second self-timer for remote
controller operation (page 129)
Select this setting:
No icon displayed
10
s
2
s
x3
2s
69
BASIC IMAGE RECORDING
3. After preparation is complete, the indicator “1sec”
appears on the monitor screen, and another
image is recorded one second later.
4. Steps 2 and 3 are repeated once more to record
the third image.
2.
Record the image.
When you press the
shutter button, the self-
timer lamp flashes and
the shutter releases
after the self-timer
reaches the end of its
countdown.
You can interrupt an
ongoing self-timer
countdown by pressing
the shutter button while
the self-timer lamp is
flashing.
Self-timer lamp
NOTES
The “2 sec” self-timer setting is best when shooting
with a slow shutter speed, because it helps to avoid
blurring of images due to hand movement.
The following functions are not available for use in
combination with the Triple Self-timer.
BULB (pages 85, 87), Continuous Shutter (page 91),
Auto Bracketing (page 95), Coupling Shot (page
107), Pre-shot (page 109)
70
BASIC IMAGE RECORDING
Specifying Image Size and Quality
You can specify the image size and image quality to suit
the type of image you are recording.
To specify the image size
“Image size” is the size of the image, expressed as the
number of vertical and horizontal pixels. A “pixel” is one of
the many tiny dots that make up the image. More pixels
provide finer detail when an image is printed, but a higher
pixel count also causes the image’s file size of to be larger.
You can select an image size to suit your needs for greater
detail or smaller file size.
1.
In the REC mode, press [MENU].
2.
Use [] and [] to select the REC tab.
3.
Use [] and [] to select Size, and then
press [].
4.
Use [] and [] to select the setting you
want, and then press [SET].
2816 x 2112 : 2816 x 2112 pixels
2816 x 1872 (3:2) : 2816 x 1872(3:2) pixels
2048 x 1536 : 2048 x 1536 pixels
1600 x 1200 : 1600 x 1200 pixels
1280 x 960 : 1280 x 960 pixels
640 x 480 : 640 x 480 pixels
NOTES
The following are guidelines for selecting the image size.
2816 x 2112
2816 x 1872
(3:2)
2048 x 1536
1600 x 1200
1280 x 960
640 x 480
When you want to do this:*
Larger
Smaller
Use this setting:*
Print the image on paper up to 358
x 268mm (14.1 x 10.6 inches)
Print the image on paper up to 358
x 238mm (14.1 x 9.4 inches)
Print the image on paper up to 260
x 195mm (10.2 x 7.7 inches)
Print the image on paper up to 203
x 152mm (8 x 6 inches)
Print the image on paper up to 163
x 122mm (6.4 x 4.8 inches)
Print the image on paper up
to 81 x 61mm (3.2 x 2.4 inches), or
attach the image to e-mail
*The sizes indicated by the settings are rough
approximates only.
71
BASIC IMAGE RECORDING
The above paper sizes are all approximate values
when printing at a resolution of 200 dpi (dots per
inch). Use a larger setting when you want to print at
a higher resolution or when you plan to produce a
larger size print.
Selecting the “2816 x 1872 (3:2)” image size records
images with a 3:2 (vertical : horizontal) aspect ratio,
which is optimal for printing on paper with an aspect
ratio of 3:2.
To specify image quality
Compressing an image before storage can cause a
deterioration of its quality. The more an image is
compressed, the greater the loss of quality. The image
quality setting specifies the compression ratio used when
an image is stored in memory. You can select an image
quality setting to suit your needs for higher quality or
smaller file size.
1.
In the REC mode, press [MENU].
2.
Use [] and [] to select the REC tab.
3.
Use [] and [] to select Quality, and then
press [].
4.
Use [] and [] to select the setting you
want, and then press [SET].
Select this setting:
Fine
Normal
Economy
TIFF
To get this:
Very high quality, but large file size
Normal quality
Small file size, but low quality
Image recording without compression
72
BASIC IMAGE RECORDING
NOTE
The following are guidelines for selecting image
quality.
TIFF
Fine
Normal
Economy
To get this:
Higher
Quality
Lower
Quality
Select this setting:
Image recording without
compression
High image quality and
memory capacity
Normal image quality and
memory capacity
Low image quality and
memory capacity
IMPORTANT!
Actual file size depends on the type of image you
record. This means that the remaining image
capacity noted on the monitor screen may not be
exactly accurate (pages 26, 243).
It takes longer to store a TIFF (uncompressed)
image than a JPEG (compressed) image.
When you record a TIFF image, a JPEG format FINE
version of the same image is also stored. The FINE
version is the one that appears on the camera’s
monitor screen when you display the image in the
PLAY mode.
A TIFF image cannot be resized (page 141), cropped
(page 142), or copied (page 186). All of these
operations must be performed on JPEG images.
You cannot transfer a TIFF image to a computer using
the bundled Photo Loader application (page 222). Use
the procedure under “Viewing Images on a
Computer” (page 198) instead.
73
OTHER RECORDING FUNCTIONS
OTHER RECORDING FUNCTIONS
This section describes other powerful features and
functions that are available for recording.
Selecting the Focus Mode
You can select one of five different focus modes: Auto
Focus, Macro, Infinity, Manual, and Pan Focus.
IMPORTANT!
Pan Focus can be used in the Movie Mode only. You
cannot use Pan Focus in any other REC mode.
1.
In the REC mode, press [ ].
Each press of [ ] cycles
thorough the focus mode
settings in the sequence
shown below.
[ ]
Focus mode indicator
To set up the camera to do this:
Focus automatically (Auto Focus)
Perform close-up focus (Macro)
Fix the focal distance (Pan Focus)
Perform infinity focus (Infinity)
Focus manually (Manual Focus)
Select this setting:
None
PF*
MF
*The PF (Pan Focus) setting is available in the Movie
Mode only.
74
OTHER RECORDING FUNCTIONS
Using Auto Focus
As its name suggests, Auto Focus focuses the image
automatically. The automatic focus operation starts when
you press the shutter button down half way. The following
is the Auto Focus range.
Range: Approximately 40cm to (1.3´ to )
1.
Keep pressing [ ] until there is no focus
mode indicator on the display.
2.
Compose the image
so the main subject is
within the focus
frame, and then press
the shutter button
half way.
You can tell whether the
image is focused by
observing the focus
frame and the green
operation lamp.
1200N
1200N
1600
1600
10
10
04/
04/
12
12
/24
24
12
12
:58
58
IN
ISO100
ISO100
F2.8
F2.8
1/1000
1/1000
Focus frame
Green operation lamp
When you see this:
Green focus frame
Green operation lamp
Red focus frame
Flashing green operation lamp
It means this:
The image is focused.
The image is not in
focus.
3.
Press the shutter button the rest of the way to
record the image.
NOTES
When “Hybrid” is selected as the Auto Focus mode
(page 118), pressing the shutter button all the way
without pausing at the half-way point will perform
high-speed Auto Focus using the phase differential
sensor only. Note, however, that high-speed Auto
Focus is somewhat less reliable than the Auto Focus
operation performed when you press the shutter
button half way and pause.
Except when you specifically need very fast focusing
and response, it is recommended that you normally
press the shutter button half way and wait for the
Auto Focus operation to complete before pressing
the shutter button the rest of the way down to record.
75
OTHER RECORDING FUNCTIONS
Specifying the Auto Focus Area
You can use the following procedure to change the Auto
Focus area used in the Auto Focus Mode and the Macro
Mode. Note that the configuration of the focus frame
changes in accordance with the Auto Focus area you
select.
1.
In the REC mode, press [MENU].
2.
On the “REC” tab, select “AF Area”, and then
press [].
3.
Use [] and [] to select the Auto Focus area
you want, and then press [SET].
For this type of Auto Focus area:
Very limited range in the center of the
screen
This setting works well with focus lock
(page 79).
Automatic selection of the focus area where
the subject closest to the camera is located
With this setting, a wide focus frame,
which contains seven focus points,
appears on the monitor screen first. When
you press the shutter button half way, the
camera automatically selects the focus
point where the subject closest to the
camera is located, and a focus frame
appears at that point.
This setting works well for group photos.
Select of the focus point using the [], [],
[], and [] keys. Then press [SET] to
display the focus frame at that point.
Select this:
Spot
Multi
Free
76
OTHER RECORDING FUNCTIONS
Spot Multi
Focus frameFocus frame
Free
Using the Macro Mode
The Macro mode lets you focus automatically on close up
subjects. The automatic focus operation starts when you
press the shutter button down half way. The following is the
focus range in the Macro mode.
Range: Approximately 10cm to 50cm (3.9˝ to 19.7˝) at
wide angle
Approximately 40cm to 50cm (15.6˝ to 19.7˝) at
telephoto
1.
Keep pressing [ ] until the focus mode
indicator shows “ ”.
2.
Record the image.
The focus and image recording operations are
identical to those in the Auto Focus mode.
You can tell whether the image is focused by
observing the focus frame and the green operation
lamp. The indications of the focus frame and green
operation lamp are the same as those in the Auto
Focus mode.
Focus frame
Focus point
[SET]
77
OTHER RECORDING FUNCTIONS
Using the Infinity Mode
The Infinity mode fixes focus at infinity (). Use this mode
when recording scenery and other faraway images.
1.
Keep pressing [ ] until the focus mode
indicator shows “ ”.
2.
Record the image.
1.
Keep pressing [ ]
until the focus mode
indicator shows
“MF”.
At this point, a
boundary also appears
on the display,
indicating the part of the
image that will be used
for manual focus.
Using Manual Focus
With the Manual Focus mode, you can adjust the focus of
an image manually. The following shows focus ranges in
the Macro mode for two optical zoom factors.
Optical Zoom Factor
1X
4X
Approximate Focus Range
10cm (3.9˝) to infinity ()
40cm (15.7˝) to infinity ()
Boundary
78
OTHER RECORDING FUNCTIONS
2.
While watching the
image on the monitor
screen, use [] and
[] to focus.
Pressing [] or [] causes the area inside of the
boundary displayed in step 1 to fill the monitor
screen momentarily to aid in focus. The normal
image reappears a short while later.
3.
Press the shutter button to record the image.
IMPORTANT!
In the Manual Focus mode, the [] and [] keys
adjust focus, even if you used key customization to
assign other functions to them (page 123).
To do this:
Focus in on the subject
Focus out on the subject
Do this:
Press [].
Press [].
Manual focus position
Using Pan Focus
You can use Pan Focus in the Movie Mode (page 111) to
fix focus at a preset distance, so Auto Focus is not
performed during movie recording.
1.
Enter the Movie Mode
(page 111).
This automatically selects
Pan Focus as the focus
mode, which is indicated
by “PF” appearing on the
monitor screen.
If another focus mode is selected in the Movie Mode,
use [ ] to display the “PF” (Pan Focus) indicator.
2.
Press the shutter button to record a movie.
IMPORTANT!
Pan Focus can be used in the Movie Mode only. You
cannot use Pan Focus in any other REC mode.
79
OTHER RECORDING FUNCTIONS
3.
When the image is composed the way you
want, press the shutter button the rest of the
way to record it.
NOTE
Locking the focus also locks the exposure.
Using Focus Lock
Focus lock is a technique you can use to focus on a subject
that is not located within the focus frame when you record
an image. You can use focus lock in the Auto Focus mode
and the Macro mode ( ).
1.
Using the monitor
screen, compose the
image so the main
subject is within the
focus frame, and then
press the shutter
button half way.
2.
Keeping the shutter
button half way down,
re-compose the
image as you like.
This locks the focus on
the subject that is
currently within the
focus frame.
1200N
1200N
1600
1600
10
10
04/
04/
12
12
/24
24
12
12
:58
58
IN
ISO100
ISO100
F2.8
F2.8
1/1000
1/1000
Focus frame
1200N
1200N
1600
1600
10
10
04/
04/
12
12
/24
24
12
12
:58
58
IN
ISO100
ISO100
F2.8
F2.8
1/1000
1/1000
80
OTHER RECORDING FUNCTIONS
3.
Use [] and [] to
change the exposure
compensation value,
and then press [SET].
Pressing [SET] registers
the displayed value.
Up : Increases the EV value. A higher EV value is best
used for light-colored subjects and backlight
subjects.
Down : Decreases the EV value. A lower EV value is best
for dark-color subjects and for shooting outdoors
on a clear day.
EV value
Exposure Compensation (EV Shift)
Exposure compensation lets you change the exposure
setting (EV value) manually to adjust for the lighting of your
subject. This feature helps to achieve better results when
recording a backlit subject, a strongly lit subject indoors, or
a subject that is against a dark background.
EV Shift Range: –2.0EV to +2.0EV
Steps: 1/3EV
1.
In the REC mode, press [MENU].
2.
Select the REC tab,
select EV Shift, and
then press [].
Exposure compensation
value
81
OTHER RECORDING FUNCTIONS
Adjusting White Balance
The wavelengths of the light produced by various light
sources (daylight, light bulb, etc.) can affect the color of a
subject when it is recorded. White balance lets you make
adjustments to compensate for different lighting types, so
the colors of an image appear more natural.
1.
In the REC mode, press [MENU].
2.
Select the REC tab,
select White
Balance, and then
press [].
To cancel EV Shift, adjust the value until it becomes
0.0.
4.
Record the image.
IMPORTANT!
When shooting under very dark or very bright
conditions, you may not be able to obtain satisfactory
results even after performing exposure
compensation.
NOTES
Performing an EV shift operation causes the
metering mode to switch automatically to center
weighted metering. Returning the EV shift value to
0.0 causes the metering mode to change back to
multi-pattern metering (page 119).
You can use key customization (page 123) to
configure the camera to perform exposure
compensation whenever you press [] or [] while in
the REC mode.
82
OTHER RECORDING FUNCTIONS
3.
Use [] and [] to select the setting you
want, and then press [SET].
NOTES
When “Auto” is selected for the white balance
setting, the camera reads the color of the subject
and automatically corrects the color balance. Certain
subject colors and lighting conditions can cause
problems for the camera as it tries to read the color.
If this happens, use one of the other fixed white
balance settings in accordance with your current
lighting conditions.
Selecting “Manual” changes white balance to the
settings achieved the last time a manual white
balance operation was performed.
You can use key customization (page 123) to
configure the camera so the white balance setting
changes whenever you press [] or [] while in the
REC mode.
When shooting under these conditions:
Normal conditions
Outdoor daylight on a clear day
Outdoor daylight on an overcast or rainy
day, in the shade of a tree, etc.
In the shade of a building or any other
area where the color temperature is high
Under incandescent lighting
Under white fluorescent light
(suppresses color fogging)
Under daylight white or daylight fluorescent
light (suppresses color fogging)
Flash
Difficult lighting that requires manual control
(See “Adjusting White Balance Manually”.)
Select this setting:
Auto
1
2
Manual
83
OTHER RECORDING FUNCTIONS
4.
Point the camera at a white paper or similar
object under the lighting conditions for which
you want to set the white balance, and then
press the shutter button.
This starts the white balance adjustment procedure.
The message “Complete” appears on the monitor
screen after white balance adjustment is complete.
Dim lighting or pointing the camera at a dark colored
object while performing manual white balance
adjustment can cause the procedure to take a long
time to complete.
5.
Press [SET].
This registers the white balance settings and returns
to the REC mode.
White paper
Adjusting White Balance Manually
Certain complex light sources or other environmental
conditions can make it impossible to obtain good results
when “Auto” or one of the fixed light source settings is
selected for white balance. Manual white balance lets you
configure the camera for a particular light source and other
conditions.
Note that you must perform manual white balance under
the same conditions you will be shooting under. You must
also have a white piece of paper or other similar object on
hand in order to perform manual white balance.
1.
In the REC mode, press [MENU].
2.
Select the “REC” tab, select “White Balance”,
and then press [].
3.
Use [] and [] to
select “Manual”.
This causes the object
you last used to adjust
manual white balance to
appear on the monitor
screen.
84
OTHER RECORDING FUNCTIONS
Available Aperture Settings
*The above values are full wide angle optical zoom.
Aperture values are different at other optical zoom
settings.
1.
Align the mode dial
with A (Aperture
Priority).
2.
Use [] and [] to select F *.*, and then use
[] and [] to change the aperture value
setting.
You could also use [] and [] to select “EV Shift”
here, and then use [] and [] to specify an
exposure compensation value (page 80).
If you are using manual focus, you can also use []
and [] to select “FOCUS” (manual focus adjustment),
and then use [] and [] to focus manually.
EV shiftAperture value
Aperture value
*
Depth of Field
Wide Small
F2.8, 3.2, 3.5, 4.0, 4.5, 5.0, 5.6, 6.3, 7.1, 8.0
Shallow Deep
Specifying the Exposure Mode
You can use the mode dial to select the exposure mode,
which controls the aperture and shutter speed settings
used during image recording.
A Mode : Aperture Priority AE
S Mode : Shutter Speed Priority AE
M Mode : Manual Exposure
Using Aperture Priority AE
When A Mode (aperture priority AE) is selected as the
exposure mode, the camera adjusts the shutter speed
automatically in accordance with a fixed aperture value
specified by you. A wider aperture (a lower aperture value)
provides a shallow depth of field, while a small aperture (a
higher aperture value) provides a greater depth of field.
Wide Aperture Small Aperture
85
OTHER RECORDING FUNCTIONS
Slow Fast
Using Shutter Speed Priority AE
When S Mode (shutter speed priority AE) is selected as the
exposure mode, the camera adjusts the aperture
automatically in accordance with a fixed shutter speed
specified by you. You should specify a shutter speed in
accordance with how much your subject is moving.
Shutter Speed Setting Range
Shutter speed
Movement
Slow Fast
BULB, 60 seconds 1/2000 second
Blurred Stopped
3.
Press the shutter button half way.
This causes the camera to configure shutter speed
automatically in accordance with the aperture value
you selected. Then it focuses the image.
The shutter speed and aperture values on the
monitor screen will turn amber when you press the
shutter button half way if the image is over-exposed
or under-exposed.
4.
When the image is focused, press the shutter
button all the way down to record.
86
OTHER RECORDING FUNCTIONS
3.
Press the shutter button half way.
This causes the camera to configure the aperture
value automatically in accordance with the shutter
speed you selected. Then it focuses the image.
The shutter speed and aperture values on the
monitor screen will turn amber when you press the
shutter button half way if the image is over-exposed
or under-exposed.
4.
When the image is focused, press the shutter
button all the way down to record.
1.
Align the mode dial
with S (Shutter
Speed Priority).
2.
Use [] and [] to select 1/**, and then use
[] and [] to change the shutter speed
setting.
You could also use [] and [] to select “EV Shift”
here, and then use [] and [] to specify an
exposure compensation value (page 80).
If you are using manual focus, you can also use [] and
[] to select “FOCUS” (manual focus adjustment), and
then use [] and [] to focus manually.
Shutter speed EV shift
87
OTHER RECORDING FUNCTIONS
1.
Align the mode dial
with M (Manual).
2.
Use [] and [] to select F *.*, and then use
[] and [] to change the aperture value
setting.
3.
Use [] and [] to select 1/**, and then use
[] and [] to change the shutter speed
setting.
If you are using manual focus, you can also use []
and [] to select “FOCUS” (manual focus adjustment),
and then use [] and [] to focus manually.
4.
Press the shutter button half way.
This causes the camera to adjust focus automatically.
5.
When the image is focused, press the shutter
button all the way down to record.
Aperture value
Shutter speed
Setting Exposure Settings Manually
In the M mode (manual exposure), you can adjust shutter
speed and aperture manually.
Available Aperture Settings
Aperture value*
Depth of Field
Wide Small
F2.8, 3.2, 3.5, 4.0, 4.5, 5.0, 5.6, 6.3, 7.1, 8.0
Shallow Deep
Shutter speed
Movement
Slow Fast
BULB, 60 seconds 1/2000 second
Blurred Stopped
*The above values are full wide angle optical zoom.
Aperture values are different at other optical zoom
settings.
Shutter Speed Setting Range
88
OTHER RECORDING FUNCTIONS
Using Manual Assist On-screen Guidance
Pressing [SET] while in the A mode (aperture priority AE),
S mode (shutter speed priority AE), or M mode (manual
exposure) causes on-screen guidance and exposure indicators
(aperture and shutter speed) to appear on the display.
Guidance
Aperture indicator
Shutter speed indicator
In the A mode, you can use [] and [] to change the
aperture value setting. Pressing a button causes the on-
screen guidance to disappear from the display.
In the S mode, you can use [] and [] to change the
shutter speed setting. Pressing a button causes the on-
screen guidance to disappear from the display.
In the M mode, you can use [] and [] to switch on-
screen guidance between the aperture value and shutter
speed settings. After displaying the screen you want, you
can use [] and [] to change the setting.
If on-screen guidance disappears from the monitor
screen, you can display it again by pressing [DISP].
IMPORTANT!
The shutter speed displayed in the A mode and the
aperture value displayed in the S mode are rough
approximations only. Because of this, these settings
may be slightly different from the settings that appear
when you press the shutter button half way (which
are more precise).
89
OTHER RECORDING FUNCTIONS
Exposure Mode Recording Precautions
You may not be able to achieve the brightness you want
when recording an image that is very dark or very bright.
If this happens, use the M mode (manual exposure) to
adjust the aperture or shutter speed manually.
You can select the “BULB” setting in the S mode (shutter
speed priority AE) or M mode (manual exposure).
With the “BULB” setting, exposure continues as long as
you keep the shutter button depressed, for up to 60
seconds.
Note that when you are using the “BULB” setting, the
record operation with the card remote controller is
different from the record operation on the camera.
Using slow shutter speeds can cause digital noise to
appear in the image. Because of this, the camera
automatically performs a noise reduction process
whenever the shutter speed is one second or slower. The
slower the shutter speed, the greater the possibility that
noise will be generated in an image. If you notice digital
noise in your images at very slow shutter speeds, try
using a shutter speed setting that is faster than four
seconds. Also note that the noise reduction process can
cause it to take longer (about double the shutter speed
setting or more) to record each image.
At shutter speeds slower than 1/8 second, the brightness
of recorded image may not be the same as the brightness
of the image that appears on the monitor screen.
Using Auto Exposure Lock (AE Lock)
The AE Lock feature lets you lock auto exposure at a
particular setting. This feature is separate from the AE lock
effect you can achieve by pressing the shutter button half way
in any exposure mode besides the M mode (manual exposure).
You can use AE Lock in the following instances.
To set up exposure on a subject that is different from
the subject selected by Auto Focus
To setup exposure prior to using the flash for recording
1.
In the REC mode, point the camera at the
subject on which you want exposure to be
performed.
90
OTHER RECORDING FUNCTIONS
2.
Press [AE-L].
This fixes the exposure
settings (aperture and
shutter speed), and
displays “AE-L” on the
monitor screen.
The AE Lock is released
by pressing [AE-L] again
or by changing to another
mode.
3.
Record the image.
AE Lock is released automatically when the image is
recorded.
AE-L
BKT
AE-L
[AE-L]
IMPORTANT!
If AE Lock is already in effect, you can re-execute it
by pressing [AE-L] once to release AE Lock, and
then pressing [AE-L] again to perform a new AE Lock
operation.
Continuous shutter recording is always performed
with AE Lock.
AE Lock can be used before starting movie recording
or while movie recording is in progress (page 111).
Proper Auto Focus may not be possible if you try to
use AE Lock to record an image in which there is a
very large variation in brightness.
You can also perform AE Lock by holding down
[AE-L], instead to performing the procedure
described above.
91
OTHER RECORDING FUNCTIONS
Using a Continuous Shutter Mode
You can configure the camera to record only a single
snapshot each time the shutter button is pressed, or to
keep recording as long as the shutter button remains
depressed. You can select from among three different
continuous shutter modes.
Normal speed continuous shutter mode
This mode records images as long as you keep the
shutter button depressed.
High speed continuous shutter mode
This mode records up to 6 consecutive images, at a
speed of about three images per second, as long as you
keep the shutter button depressed. This mode records
faster than the normal speed continuous shutter mode.
Multi continuous shutter mode
Pressing the shutter button once records 25 consecutive
stop-action frames at high speed and combines them into
a single image.
Using the Normal Speed Continuous
Shutter Mode
The normal speed continuous shutter mode records
images as long as you keep the shutter button depressed.
Recording Speed: Depends on image size and image
quality settings.
Number of Shots: Maximum number of shots possible
(based on remaining memory capacity)
1.
In the REC mode,
press [ BKT].
2.
Use [] and [] to select , and then press
[SET].
This causes “ ” to appear on the monitor screen.
3.
Press the shutter button to record.
Recording continues as long as you keep the shutter
button depressed. Release the shutter button to stop
recording.
92
OTHER RECORDING FUNCTIONS
NOTE
You can also select a continuous shutter mode by
holding down [ BKT], selecting the mode you
want with [] and [], and then releasing [ BKT].
Using the High Speed Continuous
Shutter Mode
The high speed continuous shutter mode provides higher
speed recording than the normal speed coutinuous shutter
mode.
Recording Speed: Three images per second (
The interval
between shots is longer when shooting at slow shutter
speeds
)
Maximum Number of Shots: 6
1.
In the REC mode, press [ BKT].
2.
Use [] and [] to select
H
, and then press
[SET].
This causes “ ” to appear on the monitor screen.
3.
Press the shutter button to record.
Recording continues as long as you keep the shutter
button depressed. Release the shutter button to stop
recording.
93
OTHER RECORDING FUNCTIONS
IMPORTANT!
Nothing is displayed on the monitor screen while
recording is in progress.
25-shot Stop Action Images (Using the
Multi Continuous Shutter Mode)
The multi continuous shutter
mode records 25 stop-action
shots at high speed and
combines them into a single
image.
1.
In the REC mode, press [ BKT].
2.
Use [] and [] to select , and then press
[SET].
This causes “ ” to appear on the monitor screen.
3.
Press the shutter button once to record.
After 25 shots are recorded, they are combined into
a single image, which is stored in memory.
94
OTHER RECORDING FUNCTIONS
IMPORTANT!
Note with the above procedure, you do not need to
keep the shutter button depressed.
The size of the 25-shot images is 1600 x 1200 pixels.
Continuous Shutter Precautions
Continuous shutter cannot be used when any one of the
following conditions exists.
When TIFF is selected for the image resolution (page 71)
When “BULB” is selected for the shutter speed (pages
85, 87)
When recording with the BESTSHOT night scene or
fireworks scene (page 103) (multi continuous shutter
mode only)
When using Coupling Shot or Pre-shot (pages 107, 109)
The flash is disabled while a continuous shutter mode is
being used.
You cannot use the self-timer in combination with a normal
speed continuous shutter mode. Also, you cannot use the
high speed continuous shutter mode or multi continuous
shutter mode in combination with the Triple Self-timer
(page 68).
The slowest possible shutter speed setting when using the
multi continuous shutter mode is 1/15 second.
Starting a continuous shutter operation causes the
exposure and focus settings to be fixed at the levels for
the first image. The same settings are applied to all
subsequent images.
A continuous shutter operation may stop part way through
if memory capacity runs low.
Using a slow shutter speed setting causes a longer
interval between images.
95
OTHER RECORDING FUNCTIONS
Using Auto Bracketing
Auto bracketing lets you select a single particular setting as
a variable, and then record a series of images, each of
which uses a different setting for the variable you selected.
You can then select the image(s) you want to keep.
There are two types of auto bracketing variables:
configurable and non-configurable.
Configurable Auto Bracketing Variables
There are three configurable auto bracketing variables.
Exposure
White Balance
Focus distance
With these configurable variables, you can specify how the
setting of the variable changes, and whether three or five
images should be recorded when the shutter button is
pressed.
Three images using exposure as a variable
Non-configurable Auto Bracketing Variables
There are six non-configurable auto bracketing variables.
Filter 1
Filter 2
Portrait
Sharpness
Saturation
Contrast
The shift range of a non-configurable variable and the
number of images recorded are fixed, and cannot be
changed by you.
96
OTHER RECORDING FUNCTIONS
Using Auto Bracketing with Exposure
Selected as the Variable (AE Bracketing)
With AE bracketing, you can specify recording of three
images or five images each of which is recorded with a
different Auto Exposure setting. You can also specify the
range of change for the exposure value (shift range).
You can specify the shift range you want for AE
bracketing.
1.
In the REC mode,
press [ BKT].
2.
Use [] and [] to
select “AEB”, and
then press [].
3.
Use [] and [] to specify the number of
images you want to record.
You can specify either three images or five images.
4.
Use [] and [] to specify the shift range.
5.
When the settings are the way you want,
press [SET].
This causes the AEB indicator to appear on the
monitor screen.
6.
Press the shutter button to record.
Pressing the shutter button once records the number
of images you specified.
NOTE
You can also select an auto bracketing mode by
holding down [ BKT], selecting the mode you
want with [] and [], and then releasing [ BKT].
97
OTHER RECORDING FUNCTIONS
Using Auto Bracketing with White
Balance as the Variable (WB Bracketing)
With WB bracketing, you can specify recording of three
images or five images, each of which is recorded with a
different white balance setting. As the white balance setting
changes, the image takes on a more reddish or bluish
tinge. You can also specify the range of change for the
white balance setting (shift range).
You can specify the shift range you want for WB
bracketing.
1.
In the REC mode, press [ BKT].
2.
Use [] and [] to
select “WBB”, and
then press [].
3.
Use [] and [] to specify the number of
images you want to record.
You can specify either three images or five images.
4.
Use [] and [] to specify the shift range.
5.
When the settings are the way you want,
press [SET].
This causes the WBB indicator to appear on the
monitor screen.
6.
Press the shutter button to record.
Pressing the shutter button once records the number
of images you specified.
98
OTHER RECORDING FUNCTIONS
Using Auto Bracketing with the Focus
Distance as the Variable (Focus
Bracketing)
With Focus bracketing, you can specify recording of three
images or five images, each of which is recorded using a
different focus distance setting. You can also specify the
range of change for the focus distance (shift range).
You can specify the shift range you want for focus
bracketing
1.
In the REC mode, press [ BKT].
2.
Use [] and [] to
select “AFB”, and
then press [].
3.
Use [] and [] to specify the number of
images you want to record.
You can specify either three images or five images.
4.
Use [] and [] to specify the shift range.
5.
When the settings are the way you want,
press [SET].
This causes the AFB indicator to appear on the
monitor screen.
6.
Press the shutter button to record.
Pressing the shutter button once records the number
of images you specified.
99
OTHER RECORDING FUNCTIONS
Using Auto Bracketing with Non-
configurable Variables (Multi Bracketing)
There are six non-configurable auto bracketing variables.
Filter 1 (five images)
Filter 2 (five images)
Portrait (three images)
Sharpness (three images)
Saturation (three images)
Contrast (three images)
The shift range of a non-configurable variable and the
number of images recorded are fixed, and cannot be
changed by you.
To use auto bracketing with a non-configurable
variable
1.
In the REC mode, press [ BKT].
2.
Use [] and [] to
select “Multi”, and
then press [].
3.
Use [] and [] to select the non-
configurable variable you want, and then
press [SET].
This causes the MB indicator to appear on the
monitor screen.
4.
Press the shutter button to record.
Pressing the shutter button once records the image.
After that, the image data is processed internally to
create other versions of the same image in
accordance with the selected auto bracketing
function.
NOTES
Selecting Filter 1 records images with the
monochrome, sepia, red, and purple filters.
Selecting Filter 2 records images with the green,
blue, yellow, and pink filters.
Selecting Portrait records a normal image, followed
by an image with soft focus and enhanced flesh
tones.
IMPORTANT!
Note that you can use only one non-configurable
variable at a time. You cannot use them in
combination with each other.
100
OTHER RECORDING FUNCTIONS
Auto Bracketing Precautions
Auto bracketing cannot be used when any one of the
following conditions exists.
When TIFF is selected for the image resolution (page 71)
When BULB is selected for the shutter speed (pages
85, 87)
During Coupling Shot or Pre-shot recording (pages 107,
109)
The flash is disabled while auto bracketing is being used.
The Triple Self-timer (page 68) cannot be used together
with auto bracketing.
An auto bracketing operation may stop part way through if
memory capacity or battery power runs low.
Certain menu settings may be ignored when you use Auto
Bracketing for recording.
Previewing Images Recorded with High Speed
Continuous Shutter or Auto Bracketing
You can use the following procedure to preview images
after you record them with high speed continuous shutter or
auto bracketing, without switching to the PLAY mode (page
138).
1.
After recording the
images, press
[PREVIEW].
This displays a preview
screen of the images
you just recorded with
high speed continuous
shutter or auto
bracketing.
Press [PREVIEW] again
to clear the preview
screen.
Images recorded using the
high-speed continuous
shutter mode
[PREVIEW]
101
OTHER RECORDING FUNCTIONS
2.
Use [], [], [], and [] to move the
selection boundary to the image you want to
view, and then press [SET] to display the
selected image.
This displays the image with an indicator (like )
that shows the recording method used, along with a
value indicating the image number in the series.
3.
Use [] and [] to scroll between images.
IMPORTANT!
Pressing [PREVIEW] after a normal speed, multi
continuous shutter mode, or single-image operation
displays the last image recorded only.
Pressing [PREVIEW] does not display preview
images if any of the following conditions existed
immediately before recording of images using the
high speed continuous shutter mode or auto
bracketing.
Immediately after turning on camera power
Immediately after changing the mode dial setting
Immediately after recording a new image without
high speed continuous shutter or auto bracketing.
The selection screen does not appear following a
high speed continuous shutter mode operation that
records only one image.
102
OTHER RECORDING FUNCTIONS
Deleting an Image on the Preview
Screen
You can use the preview screen to delete images recorded
with the high-speed continuous shutter mode or auto
bracketing.
IMPORTANT!
Note that image deletion cannot be undone. Once
you delete an image, it is gone. Make sure you really
do not need an image anymore before you delete it.
1.
After recording the images, press [PREVIEW]
to display the preview screen.
2.
Press [EX ].
3.
Use [] and [] to select the delete operation
you want.
4.
After the setting is the way you want, press
[SET].
IMPORTANT!
The All Delete option is not available when there is
only one image.
Select this option:
All Delete
Delete
Cancel
To do this:
Delete all of the images of the last
high-speed continuous shutter or
auto bracketing operation
Delete only the displayed image
Cancel the delete operation
103
OTHER RECORDING FUNCTIONS
Using the BESTSHOT Mode
Selecting one of the 25 BESTSHOT scenes automatically
sets up the camera for recording a similar type of image.
Example Sample Scene
Portrait Scenery
Night Scene Night Scene Portrait
1.
Align the mode dial
with .
This enters the
BESTSHOT mode and
displays a sample
scene.
2.
Use [] and [] to select the sample scene
you want, and then press [SET].
3.
Record the image.
IMPORTANT!
Sample scene number 4 is Coupling Shot scene
(page 107). Sample scene number 5 is a Pre-shot
scene (page 109).
BESTSHOT scenes were not recorded using this
camera. They are provided as samples only.
Images recorded using a BESTSHOT scene may not
produce the results you expected due to shooting
conditions and other factors.
After selecting a BESTSHOT scene, you can change
to a different one by pressing [SET] and then using
[] and [] to scroll through available scenes. When
the one you want is displayed, press [SET].
104
OTHER RECORDING FUNCTIONS
You can change the camera settings that are made
when you select a BESTSHOT scene. Note,
however, that the BESTSHOT settings revert to their
defaults when you select another BESTSHOT scene,
change the recording mode, or turn off the camera.
Noise reduction processing is performed
automatically when you are recording a night scene,
fireworks, or other image that requires slow shutter
speeds. Because of this, it takes longer to record
images at lower shutter speeds. Make sure that you
do not perform any camera button operations until
the image recording operation is complete.
NOTE
Operation guidance and
the currently selected
BESTSHOT scene
appear on the display for
about two seconds if the
camera is in the
BESTSHOT mode when
you turn it on.
Creating Your Own BESTSHOT Setup
You can use the procedure below to save the setup of an
image you recorded for later recall when you need it again.
Recalling a setup you save automatically sets up the
camera accordingly.
1.
Align the mode dial with .
This enters the BESTSHOT mode and displays a
sample scene.
2.
Use [] and [] to
display “Register
User Scene”.
3.
Press [SET].
105
OTHER RECORDING FUNCTIONS
4.
Use [] and [] to
display the image
whose setup you
want to register as a
BESTSHOT scene.
5.
Use [] and [] to
select “Save”, and
then press [SET].
This registers the setup.
Now you can use the
procedure on page 103
to select your user
setup for recording.
IMPORTANT!
BESTSHOT user setups are located in the cameras
built-in memory after the built-in sample scenes.
When a BESTSHOT user setup is recalled, the
monitor screen in step 2 of the procedure on page
103 displays the text Recall User Scene.
Note that formatting the built-in memory (page 180)
deletes all BESTSHOT user setups.
NOTES
The following are the settings that are included in a
BESTSHOT Mode user setup: focus mode, EV shift
value, filter, metering mode, white balance mode,
flash intensity, sharpness, saturation, contrast, flash
mode, ISO sensitivity, and aperture and shutter
speed.
Note that images recorded with this camera only can
be used to create a BESTSHOT user setup.
You can have up to 999 BESTSHOT user setups in
the cameras built-in memory at one time.
You can check the current setup of a scene by
displaying the various setting menus.
When you register a BESTSHOT user setup, it is
automatically assigned a file name using the format
UP600nnn.JPE (n=0 to 9).
106
OTHER RECORDING FUNCTIONS
To delete a BESTSHOT user setup
1.
Align the mode dial with .
This enters the BESTSHOT mode and displays a
sample scene.
2.
Use [] and [] to display the user setup you
want to delete.
3.
Press [EX ] to delete the user setup.
You can also delete a user setup by using your
computer to delete its file in the SCENE folder in
the cameras built-in memory (page 210).
107
OTHER RECORDING FUNCTIONS
Combined
Images
1.
Align the mode dial with .
2.
Use [] and [] to select “Coupling Shot”,
and then press [SET].
3.
Align the focus frame
on the monitor screen
with the subject you
want on the left side
of the image.
While Coupling Shot is
selected, the AF Area
(page 75) setting
automatically becomes
Spot.
Combining Shots of Two People into a
Single Image (Coupling Shot)
The Coupling Shot mode lets you record images of two
people and combine them into a single image. This makes
it possible for you to include yourself in group images, even
when there is no one else around to record the image for
you. Coupling Shot is available in the BESTSHOT mode
(page 103).
First Image This is the part
of the image that
does not include
the person who
is recording the
first image.
Second
Image
Making sure that
the background
of the image is
aligned correctly,
record the image
of the person
who recorded
the first image.
Focus frame
108
OTHER RECORDING FUNCTIONS
4.
Press the shutter button to record the left side
of the image.
The focus, exposure, white balance, zoom, and flash
settings are fixed for this type of image.
5.
Next, align the focus
frame with the subject
you want in the right
side of the image,
taking care to align
the actual background
with the semi-
transparent image of
the background of the
first image, which is
shown on the monitor
screen.
Pressing [MENU] any time after step 3 of the above
procedure cancels the first image and returns to step
3.
Semi-transparent
image
6.
When everything is aligned correctly, record
the right side of the image.
IMPORTANT!
Coupling Shot temporarily uses file memory to store
data. You may get an error during Coupling Shot
recording if there is not enough file memory available
to store the required data. If this happens, delete
images you no longer need and try again.
109
OTHER RECORDING FUNCTIONS
Recording a Subject onto an Existing
Background Image (Pre-shot)
Pre-shot helps you get the background you want, even if
you need to ask someone else to record the image for you.
Basically, Pre-shot is a two-step process.
1. You compose the background you want and press the
shutter button, which causes a semi-transparent image
of the background to remain on the monitor screen.
2. Ask someone else to record a shot of you against your
original background, telling them to compose the image
by using the semi-transparent monitor screen image as a
guide.
The camera stores the image produced by step 2 only.
Depending on how the image is actually composed in
step 2, its background may not be exactly the same as
the one you composed in step 1.
Note that Pre-shot is available in the BESTSHOT mode
only (page 103).
Freeze the background on
the monitor screen.
Record the image, using
the background on the
monitor screen as a guide.
This records the image.
110
OTHER RECORDING FUNCTIONS
1.
Align the mode dial with .
2.
Use [] and [] to select “Pre-shot”, and then
press [SET].
3.
Freeze the background on the monitor screen.
Though a semi-transparent image of the background
appears on the monitor screen in step 4, the
background image is not saved in memory at this
time.
The focus, exposure, white balance, zoom, and flash
settings are fixed for this type of image.
4.
Next, align the focus
frame with the
subject, composing
the subject with the
semi-transparent
background shown
on the monitor
screen.
Pressing [MENU] any time after step 3 of the above
procedure cancels the background image and
returns to step 3.
Semi-transparent image
5.
When everything is aligned correctly, record
the image.
This records the image composed on the monitor
screen in step 4. The reference background image is
not recorded.
111
OTHER RECORDING FUNCTIONS
Using the Movie Mode
You can record movies with audio. A single movie can be
as long as available memory capacity allows.
File Format: AVI
AVI format conforms to the Motion JPEG format promoted
by the Open DML Group.
Image Size: 320 x 240 pixels
Movie File Size: Approximately 300KB/second.
Maximum Movie Length
One Movie:
As long as available memory capacity allows
Total Movie Time:
30 seconds with built-in memory; 200 seconds with
64MB SD memory card
1.
Align the mode dial
with .
Recording time
Remaining recording time
2.
Point the camera at
the subject and then
press the shutter
button.
Movie recording
continues as long as
remaining memory
capacity allows, or until
you stop it by pressing
the shutter button
again.
The remaining recording time and recording time
values count down on the monitor screen as you
record.
Starting a movie record operation causes optical
zoom to be disabled. Only digital zoom is available
while a movie record operation is in progress. If you
want to use optical zoom to record a movie, perform
the zoom operation before starting the record
operation.
The focus mode automatically changes to Pan Focus
(page 78) when you enter the Movie mode,
regardless of the mode memorys (page 124) Focus
setting. You can, however, change to another focus
mode before starting a recording.
Movie recording indicator
112
OTHER RECORDING FUNCTIONS
3.
When movie recording is complete, the movie
file is stored in file memory.
IMPORTANT!
The flash does not fire in the Movie mode.
This camera also records audio. Note the following
points when recording a movie.
Take care that you do
not block the
microphone with your
fingers.
Good recording
results are not
possible when the
camera is too far from
the subject.
Operating camera buttons during recording can
cause button noise to be included in the audio.
Movie audio is recorded in monaural.
The camera automatically switches to the Pan
Focus (PF) (page 78) whenever you enter the
Movie Mode.
Microphone
The camera focuses automatically whenever you
have Auto Focus (page 74) or Macro ( ) selected
as the focus mode. Note that the confirmation
tone that sounds during the Auto Focus operation
will be recorded in the audio. If you do not want
confirmation tones in your audio, keep Pan Focus
(PF) as the focus mode, or select Manual Focus
(MF) and manually focus the image before
starting your recording.
Auto Focus is not performed in the case of the
Pan Focus (PF), Manual Focus (MF) and Infinity
() focus modes, and so no confirmation tone
sounds. In the case of the Manual Focus mode,
you cannot adjust focus settings while recording
is in progress. Be sure to make all adjustments
before beginning the record operation.
Certain types of memory cards take longer to
record data, which can cause movie frames to be
dropped. and
REC
flash on the monitor screen
during recording to let you know when a frame
has been dropped.
113
OTHER RECORDING FUNCTIONS
Recording Audio
Adding Audio to a Snapshot
You can add audio to a snapshot after you record it.
Image Format: JPEG
JPEG is an image format that provides efficient data
compression.
The file extension of a JPEG file is .JPG.
Audio Format: WAVE/ADPCM recording format
This is the Windows standard format for audio recording.
The file extension of a WAVE/ADPCM file is .WAV.
Recording Time:
Up to about 30 seconds per image
Audio File Size:
Approximately 120KB (30-second recording of
approximately 4KB per second)
1.
In the REC mode, press [MENU].
2.
Select the “REC” tab, select “Audio Snap”,
and then press [].
3.
Use [] and [] to select “On” and then
press [SET].
This enters the Audio Snapshot Mode and display a
indicator.
Selecting Off enters the Normal Snapshot Mode
(no audio).
4.
Press the shutter
button to record the
image.
After the image is
recorded, the camera
enters audio recording
standby, with the image
you just recorded on the
monitor screen.
You can cancel audio recording standby by pressing
[MENU].
Remaining recording time
114
OTHER RECORDING FUNCTIONS
5.
Press the shutter button to start audio
recording.
The green operation lamp flashes as recording is
performed.
Even if you have the monitor screen turned off (page
31), the monitor screen turns on while you are
adding audio to a snapshot.
6.
Recording stops after about 30 seconds or
when you press the shutter button.
IMPORTANT!
The Audio Snapshot Mode is unavailable during
image recording using any of the following: Triple
Self-timer, Continuous shutter, Auto bracketing,
Coupling Shot.
Recording Your Voice
The Voice Recording Mode provides quick and easy
recording of your voice.
Audio Format: WAVE/ADPCM recording format
This is the Windows standard format for audio recording.
The file extension of a WAVE/ADPCM file is .WAV.
Recording Time:
Approximately 40 minutes with built-in memory
Audio File Size:
Approximately 120KB (30-second recording of
approximately 4KB per second)
1.
Align the mode dial
with .
This enters the Voice
Recording Mode and
display a indicator.
Remaining recording time
115
OTHER RECORDING FUNCTIONS
2.
Press the shutter button to start voice
recording.
The remaining recording time value counts down on
the monitor screen and the green operation lamp
flashes as recording is performed.
Pressing [DISP] during voice recording turns off the
monitor screen.
You can insert index marks while recording by
pressing [SET]. See page 156 for information about
jumping to an index mark during playback.
3.
Recording stops when you press the shutter
button, when memory becomes full, or when
the battery goes dead.
Audio Recording Precautions
Keep the microphone on the
front of the camera pointed
at the subject.
Take care that you do not
block the microphone with
your fingers.
Good recording results are not possible when the camera
is too far from the subject.
Pressing the power button or rotating the mode dial stops
recording and stores any audio recorded up to that point.
You can also perform after-recording to add audio to a
snapshot after recording it, and also change the audio
recorded for an image. See page 154 for more
information.
Microphone
116
OTHER RECORDING FUNCTIONS
REC Mode Camera Settings
The following are the settings you can make before
recording an image using a REC mode.
ISO sensitivity
Auto Focus Mode (AF Mode)
Metering
Color filtering
Sharpness
Saturation
Contrast
Grid on/off
Image Review on/off
L/R key setting
Power on default settings
Resetting the camera
NOTE
You can also configure the settings listed below. See
the referenced pages for more information.
Size (page 70)
Quality (page 71)
White Balance (page 83)
AF Area (page 75)
Audio Snap (page 113)
Flash Intensity (page 66)
Digital Zoom (page 63)
117
OTHER RECORDING FUNCTIONS
Select this setting:
Auto
ISO 50
ISO 100
ISO 200
ISO 400
To get this:
Automatic sensitivity selection
Conforms to ISO 50
Conforms to ISO 100
Conforms to ISO 200
Conforms to ISO 400
IMPORTANT!
Under certain conditions, a high shutter speed in
combination with a high ISO sensitivity setting can
cause digital noise to appear inside of an image. For
clean, good-quality images, use the lowest ISO
sensitivity setting possible.
Using a high ISO sensitivity setting along with the
flash to shoot a nearby subject may result in
improper illumination of the subject.
NOTE
You can use key customization (page 123) to
configure the camera so the ISO sensitivity setting
changes whenever you press [] and [] while in the
REC mode.
Specifying ISO Sensitivity
You can change the ISO sensitivity setting for better
images in places where lighting is dim or when you are
using faster shutter speeds.
ISO sensitivity is expressed in terms of values that
originally indicated the sensitivity to light for photographic
film. A larger value indicates higher sensitivity, which is
better for recording when available lighting is dim.
1.
In the REC mode, press [MENU].
2.
Select the “REC” tab, select “ISO”, and then
press [].
3.
Use [] and [] to select the setting you want
and then press [SET].
118
OTHER RECORDING FUNCTIONS
Selecting the Auto Focus (AF) Mode
Use the following procedure to change the AF mode.
1.
In the REC mode, press [MENU].
2.
Select the “REC” tab, select “AF Mode”, and
then press [].
3.
Use [] and [] to select the setting you want,
and then press [SET].
Select this AF mode
:
Hybrid
Continuous
Contrast
To perform this type of Auto Focus:
Combination of phase difference
and contrast focus
*
Normally, you should use this mode.
At normal distance, high-speed
continual focus
Contrast focus to protect against
loss of Auto Focus because the
phase differential sensor is blocked
IMPORTANT!
Use of Continuous AF performs focus non-stop, so
battery power runs down faster than with Hybrid AF.
Be sure to use Contrast AF whenever you have a
telephoto conversion, wide angle conversion, or
close-up lens installed (page 135). Note that
Contrast AF is slower to focus than Hybrid AF.
119
OTHER RECORDING FUNCTIONS
Selecting the Metering Mode
Use the following procedure to specify multi (multi pattern)
metering, spot metering, or center weighted metering as
the metering mode.
1.
In the REC mode, press [MENU].
2.
Select the “REC” tab, select “Metering”, and
then press [].
3.
Use [] and [] to select the setting you
want, and then press [SET].
Multi (Multi pattern):
Multi (Multi pattern) metering divides the
image into sections and measures the
light in each section for a balanced
exposure reading. The camera
automatically determines shooting
conditions according to the measured
lighting pattern, and makes exposure
settings accordingly. This type of
metering provides error-free exposure
settings for a wide range of shooting
conditions.
Center Weighted:
Center weighted metering measures
light concentrating on the center of the
focus area. Use this metering method
when you want to exert some control
over exposure, without leaving settings
totally up to the camera.
Spot:
Spot metering takes readings at a very
small area. Use this metering method
when you want exposure to be set
according to the brightness of a
particular subject, without it being
affected by surrounding conditions.
120
OTHER RECORDING FUNCTIONS
Using the Filter Function
The cameras filter function lets you alter the tint of an
image when you record it.
1.
In the REC mode, press [MENU].
2.
Select the “REC” tab, select “Filter”, and then
press [].
3.
Use [] and [] to select the setting you
want, and then press [SET].
Available filter settings are: Off, B/W, Sepia, Red,
Green, Blue, Yellow, Pink, Purple
IMPORTANT!
Using the cameras filter feature produces the same
effect as attaching a color filter to the lens.
IMPORTANT!
When Multi is selected as the metering mode,
certain procedures cause the metering mode setting
to change automatically as described below.
Changing the exposure compensation setting (page
80) to a value other than 0.0 changes the metering
mode setting to Center Weighted. The metering
mode changes back to Multi when you return the
exposure compensation setting to 0.0.
Selecting manual exposure (page 87) changes the
metering mode setting to Center Weighted. The
metering mode changes back to Multi when you
select an exposure mode other than manual.
121
OTHER RECORDING FUNCTIONS
Specifying Outline Sharpness
Use the following procedure to control the sharpness of
image outlines.
1.
In the REC mode, press [MENU].
2.
Select the “REC” tab, select “Sharpness”, and
then press [].
3.
Use [] and [] to select the setting you
want, and then press [SET].
To get this:
High sharpness
Normal sharpness
Low sharpness
Select this setting:
Hard
Normal
Soft
Specifying Color Saturation
Use the following procedure to control the intensity of the
image you are recording.
1.
In the REC mode, press [MENU].
2.
Select the “REC” tab, select “Saturation”, and
then press [].
3.
Use [] and [] to select the setting you
want, and then press [SET].
To get this:
High color saturation (intensity)
Normal color saturation (intensity)
Low color saturation (intensity)
Select this setting:
High
Normal
Low
122
OTHER RECORDING FUNCTIONS
Specifying Contrast
Use this procedure to adjust the relative difference
between the light areas and dark areas of the image you
are recording.
1.
In the REC mode, press [MENU].
2.
Select the “REC” tab, select “Contrast”, and
then press [].
3.
Use [] and [] to select the setting you
want, and then press [SET].
To get this:
High contrast
Normal contrast
Low contrast
Select this setting:
High
Normal
Low
Turning the On-screen Grid On and Off
You can display gridlines on the monitor screen to help you
compose images and ensure that the camera is straight
when recording.
To do this:
Display the grid
Hide the grid
Select this setting:
On
Off
1.
In the REC mode, press [MENU].
2.
Select the “REC” tab, select “Grid”, and then
press [].
3.
Use [] and [] to select the setting you
want, and then press [SET].
123
OTHER RECORDING FUNCTIONS
To do this:
Display images on the monitor
screen for about one second
immediately after they are recorded
Do not display images immediately
after they are recorded
Select this setting:
On
Off
Turning Image Review On and Off
Image review displays an image on the monitor screen as
soon as you record it. Use the following procedure to turn
image review on and off.
1.
In the REC mode, press [MENU].
2.
Select the “REC” tab, select “Review”, and
then press [].
3.
Use [] and [] to select the setting you
want, and then press [SET].
Assigning Functions to the [] and []
Keys
A key customization feature lets you configure the []
and [] keys so they change camera settings whenever
they are pressed in the REC mode. After you configure the
[] and [] keys, you can change the setting assigned to
them without going through the menu screen.
1.
In the REC mode, press [MENU].
2.
Select the “REC” tab, select “L/R Key”, and
then press [].
3.
Use [] and [] to select the setting you
want, and then press [SET].
124
OTHER RECORDING FUNCTIONS
NOTE
The initial default setting is EV Shift.
Select this:
EV Shift
White Balance
ISO
Metering
AF Area
Off
When you want to assign this function to
[] and [] keys:
EV shift
[] decreases compensation, []
increases compensation (page 80).
White balance setting
[] and [] cycle through white
balance settings (page 81).
ISO sensitivity
[] and [] cycle through ISO
sensitivity settings (page 117).
Metering mode
[] and [] cycle through metering
modes (page 119).
AF Area
[] and [] cycle through AF areas
(page 75).
No function assigned
Specifying Power On Default Settings
The cameras mode memory feature lets you specify the
power on default settings individually for the flash mode,
focus mode, white balance mode, ISO sensitivity, AF Area,
Metering, Cont./BKT, Flash Intensity, digital zoom mode,
manual focus position and zoom position. Turning on mode
memory for a mode tells the camera to remember the
status of that mode when you turn off the camera, and
restore it the next time you turn the camera back on. When
mode memory is turned off, the camera automatically
restores the initial factory default setting for the applicable
mode.
The following table shows what happens when you turn
mode memory on or off for each mode.
125
OTHER RECORDING FUNCTIONS
Function
Flash
Focus*1
White Balance
ISO
AF Area
Metering
Cont./BKT
Flash Intensity
Digital Zoom
MF Position
Zoom Position*2
On
Setting when
camera is
turned off
Off
Auto
Auto
Auto
Auto
Spot
Multi
1 Shot
Normal
On
Last Auto Focus
position that was in
effect before you
switched to manual
focus
Wide Angle
*1 Focus mode setting is not remembered for the Movie
Mode. Mode automatically returns to PF (Pan Focus).
*2 Only the optical zoom position is remembered.
1.
In the REC mode, press [MENU].
2.
Use [] and [] to select the “Memory” tab.
3.
Use [] and [] to select the item you want to
change, and then press [].
4.
Use [] and [] to select the setting you
want, and then press [SET].
To do this:
Turn on mode memory so settings
are restored at power on
Turn off mode memory so settings
are initialized at power on
Select this setting:
On
Off
126
OTHER RECORDING FUNCTIONS
Resetting the Camera
Use the following procedure to reset all of the cameras
settings to their initial defaults as shown under Menu
Reference on page 230.
1.
In the REC mode or the PLAY mode, press
[MENU].
2.
Select the “Set Up” tab, select “Reset”, and
then press [].
3.
Use [] and [] to select “Reset”, and then
press [SET].
To cancel the procedure without resetting, select
Cancel and press [SET].
IMPORTANT!
If you change the BESTSHOT mode sample scene
selection or if you turn off the camera while it is in the
BESTSHOT mode, the cameras setup (except for
Zoom Position) will be configured according to the
BESTSHOT sample scene settings when you turn it
back on again. This is true, regardless of mode
memory on/off settings.
If you turn the camera off while in the Movie mode,
the flash will be turned off when you turn the camera
back on again, regardless of mode memory on/off
setting.
127
OTHER RECORDING FUNCTIONS
Using the Shortcut Menu
Pressing [EX ] displays a shortcut menu that you can
use to configure white balance, ISO sensitivity, metering,
and AF area settings.
1.
In the REC mode,
press [EX ].
2.
Use [] and [] to select the item you want,
and then use [] and [] to scroll through the
available settings.
3.
After configuring the settings you want, press
[SET] to exit the shortcut menu.
Refer to the following pages for details about each of
the settings.
Adjusting the White Balance (page 81)
Specifying ISO Sensitivity (page 117)
Specifying the Metering Mode (page 119)
Specifying the Auto Focus Area (page 75)
NOTE
You can also configure a setting by holding down
[EX ], selecting the item you want with [] and
[], and then changing the setting with [] and [].
The setting is applied when you release [EX ].
128
OTHER RECORDING FUNCTIONS
Using the Card Remote Controller for Recording
You can use the card remote controller that comes with the
camera when recording. By mounting the camera on a tripod
and using the remote shutter release, you can eliminate the
chance of blurred images due to accidental hand movement.
1
2
3
4
67
5
1Signal emitter
2Shutter button
3Zoom button
4SET button
5Control buttons
6DISP button
7MENU button
Loading the Battery
You need to load a lithium battery (CR2025) into the card
remote controller before you can use it to control the camera.
1.
While pressing point A in the direction
indicated by the arrow, pull the battery holder
from the remote controller.
A
129
OTHER RECORDING FUNCTIONS
2.
Wipe the surfaces of the battery with a soft,
dry cloth, and then place it onto the battery
holder so its positive , side is facing
upwards (so you can see it).
Before Using the Card Remote
Controller for Recording
Be sure to perform the following steps before using the
card remote controller for recording.
1.
In the REC mode, use
[ ] to select the
card remote controller
mode you want to use.
Enabling the card remote
controller for recording
causes either or
2s to appear on the
monitor screen.
: Pressing the remote controllers shutter button
immediately releases the shutter.
2s: Pressing the remote controllers shutter button
releases the shutter about two seconds later
(same as the 2-second self-timer).
Remote controller
operation enabled
3.
Slide the battery holder back into the remote
controller.
IMPORTANT!
Take care to ensure that the battery is not
accidentally swallowed when it is removed from the
remote controller. Particular care is required where
young children are present.
Keep button battery out of the reach of small
children. If swallowed accidentally, contact your
physician immediately.
130
OTHER RECORDING FUNCTIONS
IMPORTANT!
The 2s setting is useful when you want to be part
of the image you are recording. The delay gives you
time to look at the camera after operating the remote
controller.
The remote controller can be used in the PLAY mode
and the Voice Recording Mode, regardless of the
Triple Self-timer setting.
Using the Card Remote Controller
Point the signal emitter on the remote controller at the
cameras signal receiver (front or side), and perform the
operation you want.
Card remote controller button operations are identical to
those of the corresponding camera buttons.
The range of the card remote controller is normally about
five meters on a straight line between the signal emitter
and front camera signal receiver, and about one meter
from an angle to the right of the front of the camera.
Remote control
signal receiver
Signal emitter
131
OTHER RECORDING FUNCTIONS
IMPORTANT!
Any one of the following conditions can reduce the
range for remote controller operations.
When the card remote controller signal emitter is
at an angle to the cameras signal receiver
When the camera is exposed to bright light
When the card remote controller battery is low
Unlike the cameras shutter button, you cannot press
the remote controller shutter button half way.
Pressing the remote controller shutter button causes
the camera to perform an auto focus operation and
then record the image.
When performing a high speed or normal speed
continuous shutter mode operation with the card
remoter controller, keep the shutter button of the
card remote controller depressed.
A continuous shutter or auto bracketing record
operation may be interrupted part way through if
remote control signal reception is interfered with or if
the card remote controller battery goes low.
When using the card remote controller for BULB
recording (pages 85, 87), press the card remote
controller shutter button once to start exposure, and
a second time to stop exposure. This is different from
the operation using the cameras shutter button,
which you must keep depressed as long as you want
exposure to be performed. Note that card remote
controller shutter button operations are different from
camera shutter button operations.
Installing a conversion lens on the camera can cause
the signal receiver on the front of the camera to
become blocked. Point the card remote controller at
the signal receiver on the side of the camera in this
case (page 135).
132
OTHER RECORDING FUNCTIONS
Using an External Flash
Use of a commercially available flash unit makes it possible
to obtain a higher level of brightness (guide number) than
you get when using the built-in flash alone. An external
flash also makes it possible to extend the effective range of
flash photography.
The guide number of the internal flash is 8 (ISO 100/m).
External Flash Unit Requirements
Any external flash unit you use with this camera must
satisfy the following requirements.
Variable flash intensity (AUTO)
Flash Duration: Less than 1/1000 sec.
Coverage Angle: Coverage of 33mm equivalent 35mm
focal length lens (without wide conversion lens)
IMPORTANT!
Some flash performance may be lost when using a
ring flash or other type of unit with a long flash time.
The aperture value and ISO sensitivity available with
some flash units may not match the values
supported by your camera. In such a case, make
adjustments in the aperture setting of the external
flash and the camera until proper brightness is
achieved.
133
OTHER RECORDING FUNCTIONS
Attaching an External Flash Unit
IMPORTANT!
Always make sure that the external flash unit is
turned off before attaching it to or detaching it from
the camera. Leaving the flash unit on can cause it to
fire unexpectedly.
1.
Attach the flash units sync cable to the
cameras external flash sync terminal.
External flash
sync terminal
External
flash unit
Sync cable
When attaching an external flash unit to the camera,
you should also purchase and install a gripped
bracket that can be secured to the cameras tripod
hole.
2.
Turn on camera power and make the required
camera settings.
Exposure Mode: M (Manual Exposure) Mode
Shutter Speed: Around 1/60 (Actual setting should
be in accordance with aperture setting.)
For maximum brightness of areas that are not
reached by flash illumination, use the cameras
maximum aperture opening (F2.8).
White Balance: (Daylight)
Flash Mode: (Off)
134
OTHER RECORDING FUNCTIONS
3.
Turn on the external flash unit, and set it up
for the camera’s aperture (F) value (page 84)
and sensitivity (ISO 50 equivalent) value.
Depending on shooting conditions, proper exposure
may not be obtained even if you properly set the auto
aperture (F) value and ISO sensitivity of the flash
unit to match those of the camera. If this happens,
adjust the auto aperture (F) value, ISO sensitivity, or
other settings of the flash unit. Also try adjusting the
aperture of the camera.
IMPORTANT!
The external flash connected to the external flash
sync terminal always fires. To record an image
without using external flash, disconnect the sync
cable from the terminal or turn off external flash unit
power.
After recording an image, check it on the monitor
screen. If it is not what you expected, use the
controls on the external flash unit to adjust flash
intensity, and adjust the aperture and ISO sensitivity
settings on the camera. Note that you cannot control
external flash unit intensity using camera settings.
Close up images often tend to be overexposed. If
you are having overexposure problems, try adjusting
the aperture and ISO sensitivity settings of the
external flash unit and the camera. You can also try
using the cameras built in flash to correct for
overexposure.
Note that the cameras built in flash fires whenever
its Flash Mode setting is something other than
(Off).
Camera aperture (F) values are based on the widest
optical zoom (1X). Using telephoto can cause slight
lens darkness. Adjust the aperture and ISO
sensitivity settings of the external flash unit and the
camera as required when using optical zoom.
When using a zoom flash, a coverage angle for a
focal distance of 33mm or less for the flash unit is
recommended.
135
OTHER RECORDING FUNCTIONS
Using a Conversion Lens or Filter
Installing the optionally available Conversion Lens
Adaptors (LU-60A) on the camera makes it possible to use
a recommended conversion lens or close-up lens, or a
commercially available filter for recording.
The Conversion Lens Adaptors (LU-60A) includes a TELE
CONVERTER ADAPTOR and a WIDE CONVERTER
ADAPTOR.
The Canon Inc. conversion lenses and close-up lenses
described below are recommended for use with this
camera.
Telephoto
Focal Distance: 1.5X the focal distance of the camera
The distance from the surface of the Tele Converter to
the subject can be in the range of one meter to infinity (at
full zoom).
Canon Tele Converter TC-DC58
TELE CONVERTER
ADAPTOR
Wide Angle
Focal Distance: 0.7X the focal distance of the camera
Canon Wide Converter WC-DC58N
Macro
In the Macro Mode, the allowable distance from the close
up lens surface to the subject is 6 cm (2.4˝) to 25.1 cm
(9.9˝) (when zoom is set to maximum wide angle).
Canon Close-up Lens 250D (58mm)
WIDE CONVERTER
ADAPTOR
Wide Converter
(WC-DC58N)
Tele Converter
(TC-DC58)
TELE CONVERTER
ADAPTOR
Close-up Lens
(250D)
136
OTHER RECORDING FUNCTIONS
Installing a Conversion Lens or Close-up
Lens
A conversion lens provides your camera with telephoto or
wide angle capabilities. A close-up lens enables macro
photography.
1.
Turn off the camera, and then remove the lens
ring installed on its lens.
2.
Install either the TELE CONVERTER
ADAPTOR or WIDE CONVERTER ADAPTOR
on the camera.
3.
Install a conversion lens or close-up lens on
the camera.
IMPORTANT!
Installing a conversion lens or close-up lens can
cause blackening around the edges of the image,
which can interfere with proper operation of the
camera’s phase differential sensor. Before recording
an image, be sure to select “Contrast” for the Auto
Focus mode. See “Selecting the Auto Focus (AF)
Mode” on page 118 for more information.
Conversion Lens and Close-up Lens
Precautions
Be sure to install the TELE CONVERTER ADAPTOR or
WIDE CONVERTER ADAPTOR before installing a
conversion lens or close-up lens.
Carefully read the user documentation that comes with
the conversion lenses and close-up lens for information
about how to use them properly.
Be sure to use the monitor screen to compose images
while a conversion lens or close-up lens is installed on
the camera. Do not use the viewfinder, because its image
is not changed by the lens you are using. Also, there will
be
darkening around the edges of the image within the
viewfinder.
Installing a conversion lens or close-up lens can interfere
with proper operation of the camera’s built-in flash.
When using a conversion lens or close-up lens, select
(Off) for the flash mode or use an external flash (page 132).
When using a telephoto conversion lens, select Auto
Focus as the focus mode (page 74).
Using optical zoom to select wide angle while a telephoto
conversion lens is installed can cause blackening around
the edges of the image. Set optical zoom to telephoto
(page 62).
Use of a tripod is recommended to avoid camera movement
during recording with a telephoto conversion lens.
When using a wide angle conversion lens, select Auto
Focus or Macro ( ) as the focus mode (page 76).
137
OTHER RECORDING FUNCTIONS
The wide angle conversion lens may cause distortion of an
image.
When using a close-up lens, be sure to set the focus
mode to (Macro mode, page 76). Proper focus of a
close-up image is not possible with any other focus mode.
Optical Zoom Precautions
Optical zoom cannot be performed while a wide
angle
conversion lens is installed. This is to prevent damage to
the wide
angle
conversion lens by contact with the
camera lens as it extends.
IMPORTANT!
Be sure to reinstall the lens ring on the camera lens
when you are not using a conversion lens. Optical
zoom is disabled while the lens ring is not installed
properly, even if the camera does not have the wide
angle
conversion lens installed.
Installing a Filter
This camera supports use of commercially available 58mm
filters.
IMPORTANT!
Be sure to install the TELE CONVERTER ADAPTOR
before installing a filter. If you attach a filter directly
to the lens without the TELE CONVERTER
ADAPTOR, the convex surface of the lens will come
into contact with the filter and damage it.
Carefully read the user documentation that comes
with filters for information about how to use them
properly.
Keep the following points in mind when purchasing a
filter.
Use of a filter can cause blackening around the
edges of images.
Use of a filter may interfere with proper operation
of Auto Focus and flash.
Filters may not deliver the same results as those
obtained with a film camera.
Do not use multiple filters.
Use of commercially available lens hood may cause
blackening around the edges of images.
138
PLAYBACK
Power button
Mode dial
PLAYBACK
3.
Use [] (forward) or [] (back) to scroll
through files on the monitor screen.
NOTES
Holding down [] or [] scrolls images at high
speed.
In order to allow for faster playback image scrolling,
the image that initially appears on the monitor screen
is a preview image, which is of somewhat lower
quality than the actual display image. The actual
display image appears a short while after the preview
image. This does not apply to images copied from
another digital camera.
You can use the cameras built-in monitor screen to view
images after you record them.
Basic Playback Operation
Use the following procedure to scroll through files stored in
the cameras memory.
1.
Press the power
button to turn on the
camera.
This causes an image or
a message to appear on
the monitor screen.
2.
Align the mode dial
with (PLAY Mode).
This enters the PLAY
Mode.
139
PLAYBACK
Playing an Audio Snapshot
Perform the steps below to display an audio snapshot
(indicated by a indicator) and play its audio.
1.
In the PLAY mode, use [] and [] until the
image you want is displayed.
2.
Press [SET].
This plays back the
audio that accompanies
the displayed image.
You can perform the
following operations
while audio is playing.
IMPORTANT!
Audio volume can be adjusted only when playback is
being performed or is paused.
To do this:
Fast forward or fast reverse
the audio
Pause and unpause audio
playback
Adjust audio volume
Cancel playback
Do this:
Hold down [] or [].
Press [SET].
Press [] or [].
Press [MENU].
140
PLAYBACK
Zooming the Display Image
Perform the following procedure to zoom the image
currently on the monitor screen up to eight times its normal
size.
1.
In the PLAY mode, use [] and [] to display
the image you want.
2.
Shift the zoom
controller towards
to enlarge the image.
This displays an
indicator that shows the
current zoom factor.
You can toggle between
the zoomed image and
normal image by
pressing [DISP].
Current zoom factor
3.
Use [], [], [], and [] to shift the image
up, down, left, or right.
4.
Press [MENU] to return the image to its
original size.
IMPORTANT!
You cannot enlarge a movie image.
Depending on the original size of the recorded
image, you may not be able to zoom a display image
the full eight times its normal size.
141
PLAYBACK
4.
Use [] and [] to select the setting you
want, and then press [SET].
To do this:
Resize to 1600 x 1200 pixels (UXGA)
Resize to 1280 x 960 pixels (SXGA)
Resize to 640 x 480 pixels (VGA)
Cancel the resizing operation
Select this:
1600 x 1200
1280 x 960
640 x 480
Cancel
Resizing an Image
You can use the following procedure to change a snapshot
image to one of the three sizes.
1600 x1200-pixel UXGA size
1280 x 960-pixel SXGA size
640 x 480-pixel VGA size
VGA is the optimum image size for attachment to e-mail
messages or incorporation into Web pages.
1.
In the PLAY mode, press [MENU].
2.
Select the “PLAY
tab, select “Resize”,
and then press [].
3.
Use [] and [] to scroll through images and
display the one you want to resize.
142
PLAYBACK
Cropping an Image
Use the following procedure when you want to crop a
portion of an enlarged image and use the remaining part of
the image as an e-mail attachment, Web page image, etc.
1.
In the PLAY mode, use [] and [] to scroll
through images and display the one you want
to crop.
2.
Press [MENU].
3.
Select the “PLAY
tab, select
Trimming”, and then
press [].
This causes a cropping
boundary to appear.
4.
Use the zoom controller to make the cropping
boundary larger or smaller.
The size of the cropping boundary depends on the
size of the image on the display.
IMPORTANT!
Resizing an image creates a new file that contains
the image in the size you select. The file with the
original image also remains in memory.
Images smaller than 640 x 480 pixels cannot be
resized.
An image recorded using the 2816 x 1872 (3:2) pixel
size cannot be resized.
Note that you can resize snapshots recorded with
this camera only.
If the message This function is not supported for this
file. appears, it means that the current image cannot
be resized.
The resize operation cannot be performed if there is
not enough memory to store the resized image.
When you display a resized image on the cameras
monitor screen, the date and time indicates when the
image was originally recorded, not when the image
was resized.
143
PLAYBACK
IMPORTANT!
Cropping an image creates a new file that contains
the cropped image. The file with the original image
also remains in memory.
The smaller the image, the more limited is the size of
the cropping boundary.
You cannot resize the cropping boundary for an
image that is 640 x 480 pixels.
An image recorded using the 2816 x 1872 (3:2) pixel
size cannot be cropped.
Movie and voice recording file images cannot be
cropped.
An image recorded using another camera model
cannot be cropped.
If the message This function is not supported for this
file. appears, it means that the current image cannot
be cropped.
The cropping operation cannot be performed if there
is not enough memory to store the cropped image.
When you display a trimmed image on the cameras
monitor screen, the date and time indicates when the
image was originally recorded, not when the image
was trimmed.
5.
Use [], [], [], and [] to move the
cropping boundary up, down, left, or right
until the area of the image you want to extract
is within the boundary.
6.
Press [SET] to extract the part of the image
enclosed in the cropping boundary.
If you want to cancel the procedure at any point,
press [MENU].
144
PLAYBACK
Checking the Focus of a Recorded Image
You can use the following procedure to enlarge a recorded
image to check its focus.
1.
In the PLAY mode,
use [] and [] to
display the image
whose focus you
want to check.
2.
Press [PREVIEW].
This enlarges the image, and displays it with the
point that was focused upon in the center of the
monitor screen.
3.
Use [], [], [], and [] to scroll the image
on the monitor screen.
4.
To return the image to its normal size, press
[PREVIEW].
IMPORTANT!
You can use the above procedure to check the focus
of snapshots and audio snapshots only.
You cannot check the focus of images recorded by
any other camera model.
145
PLAYBACK
Playing a Movie
Use the following procedure to play back a movie that was
recorded in the movie mode.
1.
In the PLAY mode,
press [] and [] to
scroll through images
until the movie you
want to play is
displayed.
2.
Press [SET].
This start playback of the movie.
You can perform the following operations while a
movie is playing.
Movie icon
IMPORTANT!
You cannot repeat play a movie. To play a movie
more than once, repeat the steps of the above
procedure.
Audio volume can be adjusted only when playback is
being performed or is paused.
To do this:
Fast forward or fast reverse the
movie
Pause and unpause movie playback
Skip forward or back one frame
while paused
Cancel playback
Adjust audio volume
Do this:
Hold down []
or [].
Press [SET].
Press [] or [].
Press [MENU].
Press [] or [].
146
PLAYBACK
Displaying the 9-image View
The following procedure displays nine images on the
monitor screen at the same time.
1.
In the PLAY mode, shift the zoom controller
towards .
This displays the 9-image screen with the image that
was on the monitor screen in step 2 in the center,
with a selection boundary around it.
is displayed in the 9-image screen to indicate
voice recording file images (page 156).
When there are nine or fewer images, they are
displayed in order with Image 1 in the upper left
corner, with the selection boundary around it.
2.
Use [], [], [], and [] to move the
selection boundary to the image you want.
Pressing [] while the selection boundary is
in the right column or [] while it is in the left
column scrolls to the next full screen of nine
images.
3.
Pressing any button besides [], [], [], or
[] displays the full-size version of the image
where the selection boundary is located.
2 3
17 18 19
20 1 2
345
678
91011
12 13 14
15 16 17
18 19 20
1
Example: When there are 20 images in memory, and
Image 1 is displayed first
147
PLAYBACK
Selecting a Specific Image in the 9-
image View
1.
Display the 9-image view.
2.
Use [], [], [], and
[] to move the
selection boundary
up, down, left, or right
until it is located at
the image you want to
view.
3.
Pressing any button
besides [], [], [],
or [] displays the
selected image.
This displays the full-
size version of the
image you selected.
Selection boundary
Month/Year
Date selection cursor
Displaying the Calendar Screen
Use the following procedure to display a 1-month calendar.
While the calendar is on the display, you can select a date,
which displays the first image recorded on that date. This
helps to make it easy to find the images you want.
1.
In the PLAY mode, press [ ].
You can also display the calendar screen by
pressing [MENU] in the PLAY mode, selecting
Calendar on the PLAY tab, and then pressing [].
2.
Use [], [], [], and
[] to move the date
selection cursor.
Use the procedure
under Changing the
Date Format on page
176 to specify the date
format.
The image displayed on
the calendar for each
date is the first image
that was recorded on
that date.
148
PLAYBACK
Pressing [] while the date selection cursor is
located anywhere in the top line of the calendar
causes the previous month to appear.
Pressing [] while the date selection cursor is
located anywhere in the bottom line of the calendar
causes the next month to appear.
To exit the calendar screen, press [MENU] or [DISP].
is displayed in the calendar screen to indicate
voice recording file images (page 156).
appears in place of the image when the date
contains data that cannot be displayed by this
camera.
3.
To view the large version of a date’s image,
move the date selection cursor to the date
and then press [SET].
This displays the first image that was recorded on
the selected date.
Playing a Slide Show
Slide Show automatically plays back images in sequence
at a fixed interval.
1.
In the PLAY mode, press [MENU].
2.
Select the “PLAY” tab, select “Slideshow”,
and then press [].
149
PLAYBACK
4.
Use [] and [] to select “Start”, and then
press [SET].
This starts the slide show.
5.
To stop Slide Show, press [SET].
The slideshow will also stop automatically after the
amount of time you specified for Time elapses.
3.
Configure the slideshow settings.
See the pages indicated below for more information.
For information about
configuring this setting:
Images
Time
Interval
Cancel
Go here:
To specify the slideshow
images on page 150
To specify the slideshow
time on page 151
To set the slideshow
interval on page 151
To exit the slideshow
setting screen and cancel
the slideshow, use []
and [] to select Cancel
and then press [SET].
IMPORTANT!
Note that all buttons are disabled while an image
change is in progress. Wait until an image is stopped
on the monitor screen before performing a button
operation, or hold down the button until the image
stops.
When the slideshow comes to a movie file, it plays
the movie once and advances to the next file.
When the slideshow comes to a movie or voice
recording file, it plays the audio once and then
advances to the next file.
While audio is playing, you can use [] and [] to
adjust the volume level.
Images copied from another digital camera or a
computer may take longer time to appear than the
slideshow interval time you specify.
150
PLAYBACK
To specify the slideshow images
1.
Use [] and [] to select “Images”, and then
press [].
2.
Use [] and [] to select the setting you
want, and then press [SET].
3.
Use [] and [] to select “Start”, and then
press [SET].
This starts the slideshow.
The audio of audio snapshot and voice recording
files is also played back.
To do this:
Include all files in file memory in the
slideshow
Display a single file
Include all files in the FAVORITE
folder (page 163) in the slideshow
Select this setting:
All images
One Image
Favorites
Selecting a Particular Image for a Slideshow
When you select One image as the slideshow type, the
slide show displays only one image, without changing it.
1.
Select “One image”, and then press [].
2.
Use [] and [] to scroll through the images
until the one you want to use is on the
monitor screen.
3.
Press [SET] to
register your
selection and return
to the menu screen.
Pressing [MENU]
instead of [SET] returns
to the menu screen
without registering the
setting.
151
PLAYBACK
To specify the slideshow time
1.
Use [] and [] to select “Time”.
2.
Use [] and [] to specify the time setting
you want, and then press [SET].
You can specify a time in the range of 1 to 60
minutes.
3.
Use [] and [] to select “Start”, and then
press [SET].
This starts the slideshow.
To set the slideshow interval
1.
Use [] and [] to select “Interval”.
2.
Use [] and [] to specify the interval setting
you want, and then press [SET].
You can specify MAX, or a value in the range of 1
to 30 seconds as the interval.
When MAX is selected for the interval, only the first
frame of movie files is played.
3.
Use [] and [] to select “Start”, and then
press [SET].
This starts the slideshow.
152
PLAYBACK
5.
After you are finished configuring settings,
press [MENU] to exit the setting screen.
IMPORTANT!
You cannot rotate an image that is protected. To
rotate such an image, first unprotect it.
You may not be able to rotate a digital image that
was recorded with another type of digital camera.
You cannot rotate movie or voice record images.
Rotating the Display Image
Use the following procedure to rotate the image 90 degrees
and register the rotation information along with the image.
After you do this, the image is always displayed in its
rotated orientation.
1.
In the PLAY mode, press [MENU].
2.
Select the “PLAY” tab, select “Rotation”, and
then press [].
3.
Use [] and [] to scroll through images until
the one you want to rotate is on the monitor
screen.
4.
Use [] and [] to
select “Rotate”, and
then press [SET].
Each press of [SET]
rotates the image 90
degrees.
153
PLAYBACK
Using Image Roulette
Image Roulette cycles images like a slot machine on the
display, before stopping at one of them. When you start an
Image Roulette operation, images scroll randomly on the
screen. At first, images scroll at high speed. Then the
scrolling gradually slows down until a single image is
stopped on the screen. The image that finally appears is
random, and subject to no rules or system.
1.
While the camera is turned off, hold down []
as you press the power button to turn it on.
Keep [] held down until images appear on the
monitor screen.
This starts the Image Roulette operation, scrolling
images on the display, finally stopping at one.
2.
Press [] or [] to restart the Image Roulette
operation.
3.
To turn off Image Roulette, align the mode
dial to enter the REC mode or press the power
button to turn off the camera.
IMPORTANT!
Image Roulette does not play movie files or display
voice recording images.
Image Roulette is disabled when there is only one
snapshot image available.
Note that Image Roulette works only with images
recorded with this camera. Image Roulette may not
operate properly when other types of images are in
memory.
If you do not start another Image Roulette operation
for about one minute after the final image appears,
the camera enters its normal PLAY mode.
154
PLAYBACK
Adding Audio to a Snapshot
The after-recording feature lets you add audio to
snapshots after they are recorded. You can also re-record
an audio image (one with a icon on it).
Audio Format: WAVE/ADPCM recording format
This is the Windows standard format for audio recording.
The file extension of a WAVE/ADPCM file is .WAV.
Recording Time:
Up to about 30 seconds per image
Audio File Size:
Approximately 120KB (30-second recording of
approximately 4KB per second)
1.
In the PLAY mode, use [] and [] to scroll
through snapshots until the one to which you
want to add audio is displayed.
2.
Press [MENU].
3.
Select the “PLAY
tab, select “Dubbing”,
and then press [].
4.
Press the shutter button to start audio
recording.
5.
Recording stops after about 30 seconds or
when you press the shutter button.
155
PLAYBACK
To re-record audio
1.
In the PLAY mode, use [] and [] to scroll
through snapshots until the one whose audio
you want to re-record is displayed.
2.
Select the “PLAY” tab, select “Dubbing”, and
then press [].
3.
Use [] and [] to select “Delete”, and then
press [SET].
If you merely want to delete the audio with re-
recording, press [MENU] here to complete the
procedure.
4.
Press the shutter button to start audio
recording.
5.
Recording stops after about 30 seconds or
when you press the shutter button.
This deletes the previous recording and replaces it
with a new one.
IMPORTANT!
Keep the microphone
on the front of the
camera pointed at the
subject.
Take care that you do
not block the
microphone with your
fingers.
Good recording results
are not possible when
the camera is too far
from the subject.
Operating camera buttons during recording can
cause button noise to be included in the audio.
The (Audio) icon appears on the monitor screen
after audio recording is complete.
You will not be able to record audio when remaining
memory capacity is low.
The following types of audio recording are not
supported.
Adding audio to a movie image
Adding audio to a protected snapshot (page 162)
Audio that is re-recorded or deleted cannot be
recovered. Make sure you no longer need audio
before re-recording or deleting it.
Microphone
156
PLAYBACK
Playing Back a Voice Recording File
Perform the following steps to play back a voice recording
file.
1.
In the PLAY mode, use [] and [] to display
the voice file (a file with on it) you want to
play.
2.
Press [SET].
This starts playback of
the voice recording file
through the cameras
speaker.
You can perform the
following operations
while audio is playing.
To do this:
Fast forward or fast reverse
the audio
Pause and unpause audio
playback
Adjust audio volume
Cancel playback
Do this:
Hold down [] or [].
Press [SET].
Press [] or [].
Press [MENU].
IMPORTANT!
Audio volume can be adjusted only when playback is
being performed or is paused.
If your recording has index marks (page 114) inside
it, you can jump to the index mark before or after the
current playback location by pausing playback and
then pressing [] or []. Next, press [SET] to
resume playback from the index mark position.
157
PLAYBACK
Displaying Camera Images on a TV Screen
You can display recorded images on a TV screen and even
use a TV screen to compose images before you record
them. To display camera images on a TV, you need a
television equipped with a video input terminal, and the AV
cable that comes with the camera.
1.
Connect one end the AV cable that comes
with the camera to the camera’s [USB/AV]
port, and the other end to the video input
terminal of the TV.
Connect the yellow plug of the AV cable to the video
input (yellow) terminal of the TV, and the white plug
to the TVs audio input (white) terminal.
Note that the audio output is monaural.
AV cable
[USB/AV] (USB/AV port)
Video input terminal
TV
2.
Turn on the TV and select its video input
mode.
3.
Now when you perform normal image
playback and recording operations on the
camera, the applicable image appears on the
TV screen.
IMPORTANT!
All icons and indicators that appear on the monitor
screen also appear on the TV screen.
The cameras monitor screen will go blank during
video output.
158
PLAYBACK
Selecting the Video Input System
You can select either NTSC or PAL for the video output
system to match the system of the TV you are using.
1.
In the REC mode or PLAY mode, press
[MENU].
2.
Select the “Set Up” tab, select “Video Out”,
and then press [].
3.
Use [] and [] to select the setting you
want, and then press [SET].
If you are using a TV designed
for use in this area:
U.S., Japan, and other areas
that use the NTSC system
Europe and other areas that
use the PAL system
Select this setting:
NTSC
PAL
DELETING FILES
159
DELETING FILES
You can delete a single file, or you can delete all files
currently in memory.
IMPORTANT!
Note that file deletion cannot be undone. Once you
delete a file, it is gone. Make sure you really do not
need a file anymore before you delete it. Especially
when deleting all files, make sure you check all the
files you have stored before proceeding.
A protected file cannot be deleted. To delete a
protected file, unprotect it first (page 162).
Delete cannot be performed when all the files in
memory are protected (page 163).
Deleting an audio snapshot deletes both the image
file and the audio file attached to it.
Deleting a Single File
Perform the following steps when you want to delete a
single file.
1.
In the PLAY mode,
press [EX ].
2.
Use [] and [] to scroll through files and
display the one you want to delete.
3.
Use [] and [] to select “Delete”.
To exit the file delete operation without deleting
anything, select Cancel.
4.
Press [SET] to delete the file.
Repeat steps 2 through 4 to delete other files, if you
want.
5.
Press [MENU] to exit the menu screen.
DELETING FILES
160
Deleting All Files
The following procedure deletes all unprotected files
currently in memory.
1.
In the PLAY mode, press [EX ].
2.
Use [] and [] to select “All Files Delete”,
and then press [SET].
3.
Use [] and [] to select “Yes”.
To exit the file delete operation without deleting
anything, select No.
4.
Press [SET] to delete all the files.
The message There are no files. appears on the
screen after all of the files are deleted.
IMPORTANT!
If a file cannot be deleted for some reason, the
message This function is not supported for this file.
appears when you try to delete it.
FILE MANAGEMENT
161
FILE MANAGEMENT
The file management capabilities of the camera make it
easy to keep track of images. You can protect files against
deletion and store the files you want in the cameras built-in
memory.
Folders
Your camera automatically creates a directory of image
storage folders in its built-in Flash memory or on the
memory card.
Memory Folders and Files
An image you record is automatically stored in a folder,
whose name is a serial number. You can have up to 900
folders in memory at the same time. Folder names are
generated as shown below.
Example: Name of the 100th folder.
Each folder can hold files numbered up to 9,999.
Trying to store the 10,000th file in a folder causes the next
serially numbered folder to be created. Folder names are
generated as shown below.
Example: Name of the 26th file
Extension
CIMG0026.JPG
Serial number (4 digits)
The actual number of files you will be able to store on a
memory card depends on the image size and quality,
capacity of the card, etc.
For details about the directory structure, see Memory
Directory Structure on page 209.
100CASIO
Serial number (3 digits)
FILE MANAGEMENT
162
4.
Use [] and [] to
select “On”, and then
press [SET].
A file that is protected is
indicated by the
mark.
To unprotect a file, select
Off in step 4, and then
press [SET].
5.
Press [MENU] to exit the menu screen.
Protecting Files
Once you protect a file it cannot be deleted (page 159).
You can protect files individually or you can protect all files
in memory with a single operation.
To protect a single file
1.
In the PLAY mode, press [MENU].
2.
Select the “PLAY” tab,
select “Protect”, and
then press [].
3.
Use [] and [] to scroll through files and
display the one you want to protect.
FILE MANAGEMENT
163
To protect all files in memory
1.
In the PLAY mode, press [MENU].
2.
Select the “PLAY” tab, select “Protect”, and
then press [].
3.
Use [] and [] to select “All Files : On”, and
then press [SET].
To unprotect all files, press [SET] in step 3 so the
setting shows All Files : Off.
4.
Press [MENU] to exit the menu screen.
Using the FAVORITE Folder
You can copy scenery shots, photos of your family, or other
special images from a file storage folder (page 209) to the
FAVORITE folder in built-in memory (page 209). Images in
the FAVORITE folder are not displayed during normal
playback, so it helps to keep your personal image private
as you carry them around. FAVORITE folder images are
not deleted when you change memory cards, so you can
always keep them on hand.
To copy a file to the FAVORITE folder
1.
In the PLAY mode, press [MENU].
2.
Select the “PLAY” tab,
select “Favorites”, and
then press [].
FILE MANAGEMENT
164
3.
Use [] and [] to
select “Save”, and
then press [SET].
This displays the names
of the files in built-in
memory or on the loaded
memory card.
4.
Use [] and [] to select the file you want to
copy to the FAVORITE folder.
5.
Use [] and [] to select “Save”, and then
press [SET].
This copies the displayed file to the FAVORITE
folder.
6.
After copying all of the files you want, use []
and [] to select “Cancel”, and then press
[SET] to exit.
NOTES
Copying an image file with the above procedure
creates a 320 x 240-pixel QVGA-size image in the
FAVORITE folder.
A file copied into the FAVORITE folder is
automatically assigned a file name that is a serial
number. Though the serial number starts from 0001
and can go as high as 9999, the actual upper end of
the range depends on built-in memory capacity.
Remember that the maximum number of images that
can be stored in built-in memory depends on the size
of each image and other factors.
IMPORTANT!
Note that an image that has been copied to the
FAVORITE folder and then resized cannot be
returned to its original size.
Files in the FAVORITE folder cannot be copied to a
memory card.
FILE MANAGEMENT
165
To display a file in the FAVORITE folder
1.
In the PLAY mode, press [MENU].
2.
Select the “PLAY” tab, select “Favorites”, and
then press [].
3.
Use [] and [] to select “Show”, and then
press [SET].
If the FAVORITE folder is empty, the message No
Favorites file! appears.
4.
Use [] (forward) and
[] (back) to scroll
through the files in the
FAVORITE folder.
5.
After you are finished viewing files, press
[MENU] twice to exit.
File Name
NOTE
Holding down [] or [] scrolls images at high
speed.
IMPORTANT!
Note that a FAVORITE folder is created in the
cameras built-in memory only. No FAVORITE folder
is created on a memory card when you use one. If
you want to view the contents of the FAVORITE
folder on your computer screen, you need to remove
the memory card from the camera (if you are using
one) before connecting the USB cable and starting
data communication (pages 198, 204).
FILE MANAGEMENT
166
To delete a file from the FAVORITE
folder
1.
In the PLAY mode, press [MENU].
2.
Select the “PLAY” tab, select “Favorites”, and
then press [].
3.
Use [] and [] to select “Show”, and then
press [SET].
4.
Press [EX ].
5.
Use [] and [] to select the file you want to
delete from the FAVORITE folder.
6.
Use [] and [] to select “Delete”, and then
press [SET].
To exit the file delete operation without deleting
anything, select Cancel.
7.
After deleting all of the files you want, use []
and [] to select “Cancel”, and then press
[SET] to exit.
IMPORTANT!
You cannot use the delete operations on page 159 to
delete images from the FAVORITE folder.
Performing the memory format operation (page 180),
however, does delete FAVORITE folder files.
FILE MANAGEMENT
167
To delete all files from the FAVORITE
folder
1.
In the PLAY mode, press [MENU].
2.
Select the “PLAY” tab, select “Favorites”, and
then press [].
3.
Use [] and [] to select “Show”, and then
press [SET].
4.
Press [EX ].
5.
Use [] and [] to select “All Files Delete”,
and then press [SET].
IMPORTANT!
You cannot use the delete operations on page 159 to
delete images from the FAVORITE folder.
Performing the memory format operation (page 180),
however, does delete FAVORITE folder files.
OTHER SETTINGS
168
OTHER SETTINGS
Configuring Sound Settings
You can configure different sounds to play whenever you
turn on the camera, press the shutter button half-way or all
the way, or perform a key operation.
To configure sound settings
1.
In the REC mode or the PLAY mode, press
[MENU].
2.
Select the “Set Up” tab, select “Sounds”, and
then press [].
3.
Use [] and [] to
select the sound
whose setting you
want to configure, and
then press [].
Select this setting:
Sound 1 through Sound 5
Off
To do this:
Select a built-in sound
Turn off the sound
NOTE
The default sound setting for all operations is Sound
1.
4.
Use [] and [] to change the setting, and
then press [SET].
OTHER SETTINGS
169
To set the volume level
1.
In the REC mode or the PLAY mode, press
[MENU].
2.
Select the “Set Up” tab, select “Sounds”, and
then press [].
3.
Use [] and [] to select “Volume”.
4.
Use [] and [] to specify the volume setting
you want, and then press [SET].
You can set the volume in the range of 0 (no sound)
to 7 (loudest).
NOTE
The initial default volume setting is 3.
Specifying an Image for the Startup Screen
You can specify an image you recorded as the startup
screen image, which causes it to appear on the monitor
screen for about two seconds whenever you turn on the
camera in the REC mode.
1.
In the REC mode or the PLAY mode, press
[MENU].
2.
Select the “Set Up” tab, select “Startup”, and
then press [].
3.
Use [] and [] to display the image you want
to use as the startup image.
4.
Use [] and [] to change the setting, and
then press [SET].
Select this setting:
On
Off
To do this:
Use the currently displayed image
as the startup screen image
Disable the startup screen
OTHER SETTINGS
170
IMPORTANT!
You can select any one of the following types of
image as the startup image.
The cameras built-in startup image
A snapshot you recorded with the camera
An audio snapshot you recorded with the camera
The snapshot image that you select as the startup
image is stored in a special memory location called
startup image memory. Only one image can be
stored in startup image memory at one time.
Selecting a new startup image overwrites anything
that is already stored in startup image memory.
Because of this, if you want to return to a previous
startup image, you need to have a separate copy of
that image in the cameras standard image memory.
The startup image is deleted by the format operation
(page 180).
If you store an audio snapshot to startup image
memory, the images audio is not played when the
image is displayed at startup.
Configuring Power Down Image Settings
With the Power Down Image feature, you can configure the
camera so a specific image stored in camera image
memory appears whenever you turn off power. You can
specify a snapshot or a movie as the power down image.
To configure power down image settings
1.
Use the USB cable to connect the camera to
your computer (page 198).
2.
Move the image data that you want to use for
the power down image to the top (root)
directory of the camera’s built-in Flash
memory.
The file name extension will not be displayed if your
computer is configured to hide file name extensions.
Example: CIMG0001
If there is a memory card loaded in the camera, be
sure to copy the image to built-in memory before
removing the memory card from the camera.
OTHER SETTINGS
171
3.
Change the name of the file to one of the
following.
Snapshot Image: ENDING.JPG
Movie Image: ENDING.AVI
Input the following file name only (without file name
extension) if your computer is configured to hide file
name extensions.
File Name: ENDING
Your camera is now configured to display a power
down image. The power down image will appear any
time you press the power button to turn off the
camera. The power down image appears regardless
of whether or not your camera has a memory card
loaded in it.
IMPORTANT!
Only a snapshot (JPEG) or movie (AVI) file can be
used as the power down image.
Note that the Power Down Image feature works only
with images recorded with this camera. The Power
Down Image feature may not operate properly when
another type of image is specified as the power down
image.
Formatting the cameras Flash memory deletes the
power down image (page180).
When both a still image and a movie are present for
the power down image, only the movie is used.
Note that a power down image display operation
cannot be interrupted once it starts. Because of this,
you should select a relatively short movie when using
a movie file as the power down image.
OTHER SETTINGS
172
To cancel Power Down Image settings
1.
Use the USB cable to connect the camera to
your computer (page 198).
2.
Change the name of the current power down
image from ENDING.JPG or ENDING.AVI to
something else, or delete the current power
down image from Flash memory.
Specifying the File Name Serial Number
Generation Method
Use the following procedure to specify the method for
generating the serial number used for file names (page 161).
1.
In the REC mode or the PLAY mode, press
[MENU].
2.
Select the “Set Up” tab, select “File No.”, and
then press [].
3.
Use [] and [] to change the setting, and
then press [SET].
Select this setting:
Continue
Reset
To do this for a newly saved file:
Store the last file number used and
increment it, regardless of whether
files are deleted or whether the
memory card is replaced with a new
one
Find the highest file number in the
current folder and increment it
OTHER SETTINGS
173
Using the Alarm
You can configure up to three alarms that cause the
camera to beep and display a specified image at the time
you specify. Specifying a movie or an audio snapshot plays
back the image and the audio at the assigned time.
Specifying a voice recording file plays the audio.
To set an alarm
1.
In the PLAY mode, press [MENU].
2.
Select the “PLAY” tab, select “Alarm”, and
then press [].
3.
Use [] and [] to select the alarm whose
setting you want to configure, and then press
[].
4.
Use [] and [] to select the setting you want
to change, and then use [] and [] to
change the selected setting.
You can set an alarm time and configure the alarm to
sound either once or at the same time everyday. You
can also turn the alarm on or off.
5.
Press [DISP].
You could press [SET] in place of [DISP] if you want
to configure the alarm without an image.
6.
Use [] and [] to select the scene you want
to appear at the alarm time, and then press
[SET].
7.
After all the settings are the way you want,
press [SET].
You can configure up to three alarms, named Alarm
1, Alarm 2, and Alarm 3.
OTHER SETTINGS
174
Stopping the Alarm
When an alarm time is reached while the camera is turned
off, the alarm will sound for about one minute (or until you
stop it), and then the camera will turn on. To stop the alarm
after it starts to sound, press any button.
IMPORTANT!
Note that the alarm does not sound if the alarm time
is reached when any one of the following conditions
exists.
While the camera is turned on
While a USB data communication operation is in
progress
Setting the Clock
Use the procedures in this section to select a Home Time
zone, and to change its date and time settings.
IMPORTANT!
Make sure you select your Home Time zone (the
zone where you are currently located) before
changing the time and date settings. Otherwise, the
time and date setting will change automatically when
you select another time zone.
To select your Home Time zone
1.
In the REC mode or the PLAY mode, press
[MENU].
2.
Select the “Set Up” tab, select “World Time”,
and then press [].
This displays the current World Time zone.
3.
Use [] and [] to select “Home”, and then
press [].
OTHER SETTINGS
175
4.
Use [] and [] to select “City”, and then
press [].
5.
Use [], [], [], and [] to select the
geographical area that contains location you
want to select as your Home Time zone, and
then press [SET].
6.
Use [] and [] to select the city you want,
and then press [SET].
7.
After selecting the city you want, press [SET]
to register its zone as your Home Time zone.
To set the current time and date
1.
In the REC mode or the PLAY mode, press
[MENU].
2.
Select the “Set Up” tab, select “Adjust”, and
then press [].
3.
Set the current date and the time.
Do this:
Press [] or [].
Press [] or [].
Press [DISP].
To do this:
Change the setting at the current
cursor location
Move the cursor between settings
Toggle between 12-hour and 24-
hour timekeeping
4.
When all the settings are the way you want,
press [SET] to register them and exit the
setting screen.
OTHER SETTINGS
176
Changing the Date Format
You can select from among three different formats for
display of the date.
1.
In the REC mode or the PLAY mode, press
[MENU].
2.
Select the “Set Up” tab, select “Date Style”,
and then press [].
3.
Use [] and [] to change the setting, and
then press [SET].
Example: December 24, 2004
Select this format:
YY/MM/DD
DD/MM/YY
MM/DD/YY
To display the date like this:
04/12/24
24/12/04
12/24/04
Using World Time
You can use the World Time screen to view a time zone
that is different from the home time zone when you go on a
trip, etc. World Time can display the time in one of 162
cities in 32 time zones.
To display the World Time screen
1.
In the REC mode or the PLAY mode, press
[MENU].
2.
Select the “Set Up” tab, select “World Time”,
and then press [].
This displays the current World Time zone.
3.
Use [] and [] to select “World”.
4.
Press [SET] to exit the setting screen.
Select this:
Home
World
To do this:
Display the time in your home time zone
Display the time in a different time zone
OTHER SETTINGS
177
To configure World Time settings
1.
In the REC mode or the PLAY mode, press
[MENU].
2.
Select the “Set Up” tab, select “World Time”,
and then press [].
This displays the current World Time zone.
3.
Use [] and [] to select “World”, and then
press [].
4.
Use [] and [] to select “City”, and then
press [].
5.
Use [], [], [], and
[] to select the
geographical area you
want, and then press
[SET].
6.
Use [] and [] to
select the city you
want, and then press
[SET].
This displays the current
time in the city you
select.
7.
When the setting is the way you want, press
[SET] to apply it and exit the setting screen.
OTHER SETTINGS
178
To configure summer time (DST)
settings
1.
In the REC mode or the PLAY mode, press
[MENU].
2.
Select the “Set Up” tab, select “World Time”,
and then press [].
This displays the current World Time Settings.
3.
Use [] and [] to select “World”, and then
press [].
If you want to configure Home Time settings, select
Home instead.
4.
Use [] and [] to select “DST”, and then
press [].
5.
Use [] and [] to select the summer time
(DST) setting you want.
Select this:
On
Off
To do this:
Advance the current time setting by
one hour
Display the current time as-is
6.
After the setting is the way you want, press
[SET].
This displays the current time in accordance with
your setting.
7.
Press [SET] again to exit the setting screen.
OTHER SETTINGS
179
Changing the Display Language
You can use the following procedure to select one of ten
language as the display language.
1.
In the REC mode or the PLAY mode, press
[MENU].
2.
Select the “Set Up” tab, select “Language”,
and then press [].
3.
Use [], [], [], and [] to change the
setting, and then press [SET].
: Japanese
English : English
Français : French
Deutsch : German
Español : Spanish
Italiano : Italian
Português : Portuguese
: Chinese (Complex)
: Chinese (Simplified)
: Korean
Changing the USB Port Protocol
You can use the procedure below to change the
communication protocol of the cameras USB port when
connecting to a computer, printer, or other external device.
Select the protocol that suits the device to which you are
connecting.
1.
In the REC mode or the PLAY mode, press
[MENU].
2.
Select the “Set Up” tab, select “USB”, and
then press [].
3.
Use [] and [] to select the setting you
want, and then press [SET].
Select this setting:
Mass Storage (USB
DIRECT-PRINT)
PTP (PictBridge)*
When connecting to this type of
device:
Computer or USB DIRECT-
PRINT-compatible printer (page
192)
PictBridge-compatible printer
(page 192)
*PTP stands for Picture Transfer Protocol.
OTHER SETTINGS
180
PTP (PictBridge) simplifies the transfer of image data
to the connected device.
Mass Storage (USB DIRECT-PRINT) causes the
camera to see the computer as an external storage
device. Use this setting for normal transfer of images
from the camera to a computer (using the bundled
Photo Loader application).
Formatting Built-in Memory
Formatting built-in memory deletes any data stored in it.
IMPORTANT!
Note that data deleted by a format operation cannot
be recovered. Check to make sure you do not need
any of the data in memory before you format it.
Formatting built-in memory deletes all files, including
files in the FAVORITE folder (page 163), protected
files (page 162), and BESTSHOT user setups (page
104).
The startup screen image (page 169) and the power
down image (page 170) are deleted by formatting
memory.
1.
Check to make sure there is no memory card
loaded in the camera.
If there is a memory card loaded in the camera,
remove it (page 184).
2.
In the REC mode or the PLAY mode, press
[MENU].
3.
Select the “Set Up” tab, select “Format”, and
then press [].
OTHER SETTINGS
181
4.
Use [] and [] to select “Format”, and then
press [SET].
To exit the format operation without formatting,
select Cancel.
USING A MEMORY CARD
182
USING A MEMORY CARD
You can expand the storage
capabilities of your camera by using
a commercially available memory
card (SD memory card or
MultiMediaCard). You can also
copy files from built-in flash
memory to a memory card and from
a memory card to flash memory.
Normally, files are stored in built-in flash memory. When
you insert a memory card, however, the camera
automatically stores files to the card.
Note that you cannot save files to built-in memory while a
memory card is installed in the camera.
IMPORTANT!
Use only an SD memory card or a MultiMediaCard
with this camera. Proper operation is not guaranteed
when any other type of card is used.
See the instructions that come with the memory card
for information about how to use it.
Certain types of cards can slow down processing
speeds.
SD memory cards have a write protect switch, which
you can use to protect against accidental deletion of
image data. Note, however, if you write protect an
SD memory card, you must remove write protection
whenever you want to record to it, format it, or delete
any of its files.
Electrostatic charge, electrical noise, and other
phenomena can cause data to become corrupted or
even lost. Always make sure that you always back
up important data on other media (CD-R, CD-RW,
MO disc, computer hard disk, etc.)
USING A MEMORY CARD
183
2.
Positioning the memory
card so its front is facing in
the same direction as the
camera’s monitor screen,
carefully slide it into the
card slot.
3.
Swing the battery
compartment cover closed,
and then slide it in the
direction indicated by the
arrow.
Using a Memory Card
IMPORTANT!
Make sure you turn off the camera before inserting or
removing a memory card.
Be sure to orient the card correctly when inserting it.
Never try to force a memory card into the slot when
you feel resistance.
To insert a memory card into the camera
1.
While pressing the battery
compartment cover on the
bottom of the camera, slide
the cover in the direction
indicated by the arrow, and
then swing it open.
BackFront
USING A MEMORY CARD
184
Formatting a Memory Card
Formatting a memory card deletes any data already stored
on it.
IMPORTANT!
Be sure to use the camera to format a memory card.
Formatting a memory card on a computer and then
using it in the camera can slow down data
processing by the camera. In the case of an SD card,
formatting on a computer can result in non-
conformity with the SD format, causing problems with
compatibility, operation, etc.
Note that data deleted by a memory card format
operation cannot be recovered. Check to make sure
you do not need any of the data on the memory card
before you format it.
Formatting a memory card that contains files deletes
all the files, even those that are protected (page
162).
To remove a memory card from the
camera
1.
Press the memory card into
the camera and then release
it. This will cause the card to
come part way out of the
camera.
2.
Pull the memory card out of the slot.
IMPORTANT!
Never insert any other object besides a memory card
into the cameras card slot. Doing so creates the risk
of damage to the camera and card.
Should water or any foreign object ever get into the
card slot, immediately turn off the camera, remove
the battery, and contact your dealer or nearest
CASIO authorized service center.
Never remove a card from the camera while the
green operation lamp is flashing. Doing so can cause
the file save operation to fail, and even damage the
memory card.
USING A MEMORY CARD
185
Memory Card Precautions
If a memory card starts to behave abnormally, you can
restore normal operation by reformatting it. However, we
recommend that you always take along more than one
memory card whenever using the camera far away from
the home or office.
We recommend that you format a memory card before
using it for the first time after purchasing it, or whenever
the card you are using seems to be the cause of
abnormal images.
Before starting a format operation, check to make sure
that the battery is fully charged. Power interruption during
the format operation can result in improper formatting,
and even damage the memory card and make it
unusable.
1.
Load the memory card into the camera.
2.
Turn on the camera. Next, enter the REC
mode or PLAY mode and press [MENU].
3.
Select the “Set Up” tab, select “Format”, and
then press [].
4.
Use [] and [] to select “Format”, and then
press [SET].
To exit the format operation without formatting,
select Cancel.
USING A MEMORY CARD
186
3.
Select the “PLAY” tab,
select “Copy”, and
then press [].
4.
Use [] and [] to select “Built-in Card”,
and then press [SET].
This starts the copy operation and displays the
message Busy.... Please wait....
After the copy operation is complete, the monitor
screen shows the last file in the folder.
Copying Files
Use the procedures below to copy files between built-in
memory and a memory card.
IMPORTANT!
Only snapshot, movie files, audio snapshot, and
voice recording files recorded with this camera can
be copied. Other files cannot be copied.
Files in the FAVORITE folder cannot be copied.
Copying an audio snapshot copies both the image
file and the audio file.
To copy all the files in built-in memory to
a memory card
1.
Load the memory card into the camera.
2.
Turn on the camera. Next, enter the PLAY
mode and press [MENU].
USING A MEMORY CARD
187
To copy a file from a memory card to
built-in memory
With this procedure you can copy one file at a time.
1.
Perform steps 1 through 3 of the procedure
under “To copy all the files in built-in memory
to a memory card”.
2.
Use [] and [] to select “Card Built-in”,
and then press [SET].
3.
Use [] and [] to select the file you want to
copy.
4.
Use [] and [] to select “Copy”, and then
press [SET].
This starts the copy operation and displays the
message Busy.... Please wait....
The file reappears on the monitor screen after the
copy operation is complete.
Repeat steps 3 through 4 to copy other images, if
you want.
5.
Press [MENU] to exit the copy operation.
NOTE
Files are copied to the folder in built-in memory
whose name has the largest number.
PRINTING IMAGES
188
PRINTING IMAGES
A digital camera provides you with a variety of different
ways to print the images it records. The three main printing
methods are described below. Use the method that best
suits your needs.
Professional Print Service
The cameras DPOF feature lets you specify which images
you want to print and how many copies of each you want.
Then, simply take the memory card to a professional print
service where they will print your images in accordance
with your specifications. For more information, see DPOF
(page 189).
Printing Directly on a Printer Equipped with
a Card Slot, or a Printer that Supports USB
DIRECT-PRINT or PictBridge
The cameras DPOF feature lets you specify which images
you want to print and how many copies of each you want.
Then you can plug the memory card into a printer equipped
with a card slot, or connect the camera to a PictBridge or
USB DIRECT-PRINT printer for printing. For more
information, see DPOF (page 189) and Using PictBridge
or USB DIRECT-PRINT (page 192).
Printing with a Computer
Windows Users
The camera comes bundled with Photo Loader and
Photohands applications (page 222), which can be installed
on a Windows computer for image transfer, management,
and printing. For more information, see Viewing Images on
a Computer (page 198) and Installing the Software from
the CD-ROM (page 221).
IMPORTANT!
Refer to the pages referenced above for information
about how to connect the camera to a computer.
Image management procedures are provided in the
following pages of this section.
PRINTING IMAGES
189
Macintosh Users
The camera comes bundled with Photo Loader for the
Macintosh, which can be installed for image transfer and
management, but not for printing. Use commercially
available software for printing with a Macintosh. For more
information, see Viewing Images on a Computer (page
198) and Installing the Software from the CD-ROM (page
221).
IMPORTANT!
Refer to the pages referenced above for information
about how to connect the camera to a computer.
Image management procedures are provided in the
following pages of this section.
DPOF
The letters DPOF stand for Digital Print
Order Format, which is a format for
recording on a memory card or other medium
which digital camera images should be
printed and how many copies of the image
should be printed. Then you can print on a
DPOF-compatible printer or at a professional
print service in accordance with the file name
and number of copies settings recorded on
the card.
With this camera, you can select images by viewing them
on the monitor screen without needing to remember the file
name, its location in memory, etc.
DPOF Settings
File Name,
number of copies,
date
PRINTING IMAGES
190
To configure print settings for a single
image
1.
In the PLAY mode, press [MENU].
2.
Select the “PLAY” tab,
select “DPOF”, and
then press [].
3.
Use [] and [] to select “Select images”,
and then press [].
4.
Use [] and [] to
display the image you
want.
5.
Use [] and [] to specify the number of
copies.
You can specify up to 99 for the number of copies.
Specify 00 if you do not want to have the image
printed.
6.
To turn on date stamping for the prints, press
[DISP] so
12
12
1
is displayed.
12
12
1
indicates that date stamping is turned on.
To turn off date stamping for the prints, press [DISP]
so
12
12
1
is not displayed.
Repeat steps 4 through 6 if you want to configure
other images for printing.
7.
After all the settings are the way you want,
press [SET] to apply them.
PRINTING IMAGES
191
To configure print settings for all images
1.
In the PLAY mode, press [MENU].
2.
Select the “PLAY” tab, select “DPOF”, and
then press [].
3.
Use [] and [] to select “All images”, and
then press [].
4.
Use [] and [] to
specify the number of
copies.
You can specify up to 99
for the number of copies.
Specify 00 if you do not
want to have the image
printed.
5.
To turn on date stamping for the prints, press
[DISP] so
12
12
1
is displayed.
12
12
1
indicates that date stamping is turned on.
To turn off date stamping for the prints, press [DISP]
so
12
12
1
is not displayed.
6.
After all the settings are the way you want,
press [SET] to apply them.
IMPORTANT!
If you take a memory card to a professional print
service, be sure to tell them that it includes DPOF
settings for the images to be printed and the number
of copies. If you dont, they may print all images on
the card, including the ones you do not want printed.
Note that some professional print services do not
support DPOF printing. Check with your service
before ordering prints.
Some printers may have settings that disable date
stamp and/or DPOF printing. See the user
documentation that comes with your printer for
details about how to enable these features.
PRINTING IMAGES
192
To print a single image
1.
In the REC mode or the PLAY mode, press
[MENU].
2.
Select the “Set Up” tab, select “USB”, and
then press [].
3.
Use [] and [] to select the setting you
want, and then press [SET].
Using PictBridge or USB DIRECT-PRINT
You can connect the camera
directly to a printer that supports
PictBridge or USB DIRECT-PRINT,
and perform image selection and
printing using the camera monitor
screen and controls. DPOF support
(page 189) also lets you specify
which images you want to print and
how many copies of each should be
printed.
PictBridge is a standard
established by the Camera and
Imaging Products Association
(CIPA).
USB DIRECT-PRINT is a
standard proposed by Seiko
Epson Corporation.
IMPORTANT!
Use of the optional AC adaptor (AD-C40) is
recommended when printing with PictBridge or USB
DIRECT-PRINT.
Select this setting:
Mass Storage (USB
DIRECT-PRINT)
PTP (PictBridge)
When connecting to this type of
device:
Computer or USB DIRECT-
PRINT-compatible printer
PictBridge-compatible printer
Mass Storage (USB DIRECT-PRINT) causes the
camera to see the computer as an external storage
device. Use this setting for normal transfer of images
from the camera to a computer (using the bundled
Photo Loader application).
PTP (PictBridge) simplifies the transfer of image data
to the connected device.
PRINTING IMAGES
193
4.
Connect the optionally available AC adaptor
to the camera.
If you are using battery to power the camera, check
to make sure that the battery power level is high
enough to support the operation you are about to
perform.
Note that the camera does not draw any power over
the USB cable.
USB
USB/AV
5.
Use the USB cable that comes with the
camera to connect the camera to a printer.
6.
Load paper for printing the images into the
printer.
7.
Turn on the printer.
This displays the print
menu on the cameras
monitor screen.
8.
On the print menu,
use [] and [] to
select “1 Image”, and
then press [SET].
You can use [] and []
to select the image you
want to print.
You can toggle date stamping of the image on and
off by pressing [DISP]. The
12
12
1
icon indicates that
date stamping is turned on.
AC adaptor
PRINTING IMAGES
194
9
.
On the camera’s monitor screen, use [] and
[] to select “Print”, and then press [SET].
This starts printing and displays the message
Busy.... Please wait... on the monitor screen. The
message will disappear after a short while, even
though printing is still being performed. Pressing any
of the cameras buttons while printing is in progress
will cause the message to reappear.
The print menu will appear when printing is
complete.
To print again, repeat the above from step 8.
10.
The camera will turn off automatically when
printing is complete. After this happens,
disconnect the USB cable from the camera.
To print a group of images
1.
Use the DPOF procedure on page 189 to
specify the images in file memory that you
want to print.
2.
Perform steps 1 through 7 of the procedure
under “To print a single image” on page 192.
3.
On the print menu, use [] and [] to select
DPOF”, and then press [SET].
PRINTING IMAGES
195
4.
On the camera’s monitor screen, use [] and
[] to select “Print”, and then press [SET].
This starts printing and displays the message
Busy.... Please wait... on the monitor screen. The
message will disappear after a short while, even
though printing is still being performed. Pressing any
of the cameras buttons while printing is in progress
will cause the message to reappear.
The print menu will appear when printing is
complete.
This automatically starts printing of the images you
specified with the DPOF procedure.
To print again, repeat the above from step 3.
A message appears on the monitor screen, followed
by the DPOF setting screen (page 190), if there are
no DPOF settings currently configured on the
camera to control the printing operation. If this
happens, configure the required DPOF settings and
then perform step 6 of the above procedure again.
5.
The camera will turn off automatically when
printing is complete. After this happens,
disconnect the USB cable from the camera.
PRINTING IMAGES
196
Printing Precautions
See the documentation that comes with your printer for
information about print quality and paper settings.
Contact your printer manufacturer for information about
models that support PictBridge and USB DIRECT-PRINT,
upgrades, etc.
Never disconnect the USB cable, or perform any camera
operation while printing is in progress. Doing so causes a
printer error.
PRINT Image Matching II
Images include PRINT Image Matching
II data (mode setting and other camera
setup information). A printer that
supports PRINT Image Matching II
reads this data and adjusts the printed
image accordingly, so your images
come out just the way you intended
when you recorded them.
*Seiko Epson Corporation holds the
copyright for PRINT Image Matching and
PRINT Image Matching II.
PRINTING IMAGES
197
Exif Print
Exif Print is an
internationally supported,
open standard file format
that makes it possible to
capture and display vibrant
digital images with accurate
colors. With Exif 2.2, files
include a wide range of
shooting condition
information that can be
interpreted by an Exif Print
printer to produce better-
looking prints.
IMPORTANT!
Information about the availability of Exif Print
compatible printer models can be obtained from each
printer manufacturer.
VIEWING IMAGES ON A COMPUTER
198
VIEWING IMAGES ON A COMPUTER
After using the USB cable to establish a USB connection
between the camera and your computer, you can use your
computer to view images in file memory and copy images
to your computers hard disk or other storage media. In
order to do this, you first need to install the USB driver
located on the CD-ROM that comes bundled with the
camera onto your computer.
Note that the procedure you need to perform depends on
whether you are using computer running under Windows
(see below) or a Macintosh (see page 204).
Using the Camera with a Windows
Computer
The following are the general steps for viewing and copying
files from a computer running under Windows. You can find
details about each operation in the procedures that follow
below. Note that you should also refer to the
documentation that comes with your computer for other
information about USB connections, etc.
1. If you are running Windows 98, Me, or 2000, install
the USB driver onto your computer.
You need to perform this step only once, the first
time you connect to your computer.
If you are running Windows XP, you do not need to
install the USB driver.
2. Use the USB cable to establish a connection between
the camera and computer.
3. View and copy the images you want.
VIEWING IMAGES ON A COMPUTER
199
1.
What you should do first depends on whether
your computer is running under Windows 98/
Me/2000 or Windows XP.
Windows 98/Me/2000 Users
Start from step 2 to install the USB driver.
Note that the example installation presented here
uses Windows 98.
Windows XP Users
Installation of the USB driver is not required, so jump
directly to step 6.
2.
Set the bundled CD-ROM (CASIO Digital
Camera Software) into the CD-ROM drive of
your computer.
3.
On the menu screen that appears, click
“English”.
4.
Click [USB driver] and then [Install].
This starts installation.
The following steps show installation under the
English version of Windows.
IMPORTANT!
If you want to transfer files from the cameras built-in
memory to a computer, make sure there is no
memory card loaded in the camera before you
connect the USB cable.
If battery goes low while you are not using the AC
adaptor, data communication may stop and the
camera may shut down. Use of the special AC
adaptor is recommended to power the camera during
data communication.
Do not try to establish a connection between the camera
and computer before installing the USB driver onto the
computer. If you do, the computer will not be able to
recognize the camera.
USB driver installation is required in the case of
Windows 98, Me, and 2000. Do not connect the
camera to a computer running one of the above
operating systems without installing the USB driver
first.
USB driver installation is not required in the case of
Windows XP.
VIEWING IMAGES ON A COMPUTER
200
5.
On the screen that appears after installation
is complete, select the “Yes, I want to restart
my computer now.” check box and then click
[Finish] to restart your computer.
6.
Connect the optional AC adaptor to the [DC IN]
connector of the camera, and then plug it in
to a household power outlet.
If you are using battery to power the camera, check
to make sure that the battery power level is high
enough to support the operation you are about to
perform.
Plug
Terminal panel
cover
[DC IN]
AC power cord
AC adaptor
VIEWING IMAGES ON A COMPUTER
201
USB/AV
7.
Turn on the camera.
It makes no difference whether the camera is in the
REC mode or PLAY mode.
8.
Select the “Set Up” tab, select “USB”, and
then press [].
9
.
Use [] and [] to select “Mass Storage (USB
DIRECT-PRINT)”, and then press [SET].
10
.
Connect the USB cable that comes bundled
with the camera to the camera’s [USB/AV]
port and your computer’s USB port.
This will cause the New Hardware... dialog box to
appear on the computer screen as the computer
automatically detects the cameras file memory. After
you install the USB driver, New Hardware... dialog
box will no longer appear when you perform the
above steps to establish a USB connection.
The cameras green operation lamp lights (page 233).
BKT
At this point, some operating systems will display a
Removable Disk dialog box. If your operating
system does, close the dialog box.
Take care when connecting the USB cable to the
camera or your computer. USB ports and cable plugs
are shaped for proper positioning.
Plug the USB cable plugs into the ports securely, as
far as they will go. Proper operation is not possible if
connections are not correct.
Green operation lamp
USB port
Connector (A)
USB cable
(bundled)
[USB/AV]
VIEWING IMAGES ON A COMPUTER
202
11
.
On your computer, double-click “My
Computer”.
If you are running Windows XP, click [Start] and then
[My Computer].
12.
Double-click “Removable Disk”.
Your computer sees the cameras file memory as a
removable disk.
13.
Double-click the “Dcim” folder.
14.
Double-click the folder that contains the
image you want.
15.
Double-click the file that contains the image
you want to view.
For information about file names, see Memory
Directory Structure on page 209.
16.
Depending on your operating system, perform
one of the following procedures to save the
files, if you want.
Windows 98, 2000, Me
1. In the cameras file memory (Removable Disk), right-
click the Dcim folder.
2. On the shortcut menu that appears, click [Copy].
3. Double click [My Documents] to open it.
4. On the My Documents [Edit] menu, click [Paste].
This copies the Dcim folder (which contains the
image files) to your My Documents folder.
Windows XP
1. In the cameras file memory (Removable Disk), right-
click the Dcim folder.
2. On the shortcut menu that appears, click [Copy].
3. Click [Start] and then [My Documents].
4. On the My Documents [Edit] menu, click [Paste].
This copies the Dcim folder (which contains the
image files) to your My Documents folder.
VIEWING IMAGES ON A COMPUTER
203
IMPORTANT!
Never use your computer to edit, delete, move, or
rename images stored in file memory. Doing so can
cause problems with the image management data
used by the camera, which may make it impossible
to display images on the camera or it may cause a
large error in the number of images value displayed
by the camera. Always copy images to your
computer memory before performing any edit, delete,
move, or rename operation.
17.
Depending on the version of Windows you are
running, use one of the following procedures
to terminate the USB connection.
Windows Me/98/XP Users
Press the cameras power button. After making sure
that the cameras green operation lamp is not lit,
disconnect the camera from the computer.
Windows 2000 Users
Click card services in the task tray on your computer
screen, and disable the drive number assigned to the
camera. Next, disconnect the USB cable from the
camera, and then turn off the camera.
USB Connection Precautions
Do not leave the same image displayed on your computer
screen for a long time. Doing so can cause the image to
burn in on the screen.
Never disconnect the USB cable, or perform any camera
operation while data communication is in progress. Doing
so can cause data to become corrupted.
VIEWING IMAGES ON A COMPUTER
204
Using the Camera with a Macintosh
Computer
The following are the general steps for viewing and copying
files from a Macintosh.
You can find details about each operation in the
procedures that follow below. Note that you should also
refer to the documentation that comes with your Macintosh
for other information about USB connections, etc.
IMPORTANT!
This camera does not support operation with a
computer running Mac OS 8.6 or lower, or Mac OS X
10.0.
If you have a Macintosh running Mac OS 9 or
OS X (10.1, 10.2 or higher), use the standard USB
driver that comes with your OS.
1. Use the USB cable to establish a connection between
the camera and your Macintosh.
2. View and copy the images you want.
IMPORTANT!
Low battery power can cause the camera to power
down suddenly during data communication. Use the
optional AC adaptor is recommended to power the
camera during data communication with a computer.
If you want to transfer files from the cameras built-in
memory to a computer, make sure there is no
memory card loaded in the camera before you
connect the USB cable.
VIEWING IMAGES ON A COMPUTER
205
1.
Connect the optional AC adaptor to the [DC IN]
connector of the camera, and then plug it in
to a household power outlet.
If you are using battery to power the camera, check
to make sure that the battery power level is high
enough to support the operation you are about to
perform.
Plug
Terminal panel
cover
[DC IN]
AC power cord
AC adaptor
2.
Turn on the camera.
It makes no difference whether the camera is in the
REC mode or PLAY mode.
3.
Select the “Set Up” tab, select “USB”, and
then press [].
4.
Use [] and [] to select “Mass Storage (USB
DIRECT-PRINT)”, and then press [SET].
5.
Connect the USB cable that comes bundled
with the camera to the camera’s [USB/AV]
port and your computer’s USB port.
USB/AV
USB port
Connector (A)
USB cable
(bundled)
[USB/AV]
VIEWING IMAGES ON A COMPUTER
206
Take care when connecting the USB cable to the
camera or your computer. USB ports and cable plugs
are shaped for proper positioning.
Plug the USB cable plugs into the ports securely, as
far as they will go. Proper operation is not possible if
connections are not correct.
6.
Your Macintosh will see the camera’s file
memory as a drive.
The appearance of the drive icon depends on the
Mac OS version you are using.
After installing the USB driver, your Macintosh will
see the cameras file memory as a drive whenever
you establish a USB connection between them.
7.
Double-click the drive icon for the camera’s
file memory, the “DCIM” folder, and then the
folder that contains the image you want.
8.
Double-click the file that contains the image
you want to view.
For information about file names, see Memory
Directory Structure on page 209.
9.
To copy all the files in file memory to your
Macintosh hard disk, drag the “DCIM” folder
to the folder to which you want to copy it.
IMPORTANT!
Never use your computer to edit, delete, move, or
rename images stored in file memory. Doing so can
cause problems with the image management data
used by the camera, which may make it impossible
to display images on the camera or it may cause a
large error in the number of images value displayed
by the camera. Always copy images to your
computer memory before performing any edit, delete,
move, or rename operation.
10
.
To terminate the USB connection, drag the
drive icon that represents the camera to
Trash. Next, disconnect the USB cable from
the camera, and then turn off the camera.
VIEWING IMAGES ON A COMPUTER
207
USB Connection Precautions
Do not leave the same image displayed on your computer
screen for a long time. Doing so can cause the image to
burn in on the screen.
Never disconnect the USB cable, or perform any camera
operation while data communication is in progress. Doing
so can cause data to become corrupted.
Operations You Can Perform from Your
Computer
The following are the operations you can perform while
there is a USB connection between your camera and
computer. See the referenced pages for more information
about each operation.
View images in album format
.... See Using the Album Feature on page 213.
Print images in album format
.... See Using the Album Feature on page 213.
Automatically transfer images to your computer and
manage images
.... See Installing the Software from the CD-ROM on
page 221 for information about installing Photo
Loader.
Retouch images
.... See Installing the Software from the CD-ROM on
page 221 for information about installing Photohands.
VIEWING IMAGES ON A COMPUTER
208
Using a Memory Card to Transfer Images
to a Computer
The procedures in this section describe how to transfer
images from the camera to your computer using a memory
card.
Using a Computer with a Built-in SD Memory Card Slot
Insert the SD memory card directly into the slot.
Using a Computer with a Built-in PC Card Slot
Use a commercially available PC card adapter (for an SD
memory card/MMC). For full details, see the user
documentation that comes with the PC card adapter and
your computer.
Using a Commercially Available SD Memory Card
Reader/Writer
See the user documentation that comes with the SD
memory card reader/writer for details about how to use it.
Using a Commercially Available PC Card Reader/Writer
and PC Card Adapter (for SD Memory Cards and
MMCs)
See the user documentation that comes with the PC card
reader/writer and PC card adapter (for an SD memory card/
MMC) for details about how to use them.
VIEWING IMAGES ON A COMPUTER
209
Memory Data
Images recorded with this camera and other data are
stored in memory using DCF (Design rule for Camera File
System) protocol. DCF protocol is designed to make it
easier to exchange image and other data between digital
cameras and other devices.
DCF Protocol
DCF devices (digital cameras, printers, etc.) can exchange
images with each other. DCF protocol defines camera
format for image file data and the directory structure for file
memory, so images can be viewed using another
manufacturers DCF camera or printed on a DCF printer.
Memory Directory Structure
Directory Structure
DCIM (DCIM Folder)
100CASIO (Storage folder)
CIMG0001.JPG (Image file)
CIMG0002.AVI (Movie file)
CIMG0003.WAV (Audio file)
CIMG0004.JPG (Audio snapshot image file)
CIMG0004.WAV (Audio snapshot audio file)
101CASIO (Storage folder)
102CASIO (Storage folder)
ALBUM (Album folder)
INDEX.HTM (Album HTML file)
FAVORITE*(FAVORITE folder)
CIMG0001.JPG (Storage file)
CIMG0002.JPG (Storage file)
MISC (DPOF file folder)
AUTPRINT.MRK (DPOF file)
TIFF (TIFF Data Folder)
100CASIO (TIFF Image Folder)
CIMG0001.TIF (TIFF Image File)
. . . . . . . . .
. . . . . .
VIEWING IMAGES ON A COMPUTER
210
SCENE
*
(BESTSHOT folder)
UP600001.JPE (User setup file)
UP600002.JPE (User setup file)
*These folders are created in built-in memory only.
. . .
Folder and File Contents
DCIM folder
Folder that stores all of the digital camera files
Storage folder
Folder for storing files created by the digital camera
Image file
File that contains an image recorded with the digital
camera (File Name Extension: JPG)
Movie file
File that contains a movie recorded with the digital
camera (File Name Extension: AVI)
Audio file
File that contains an audio recording (File Name
Extension: WAV).
Audio snapshot image file
File that contains the image part of an audio snapshot
(File Name Extension: JPG).
Audio snapshot audio file
File that contains the audio part of an audio snapshot
(File Name Extension: WAV).
Album folder
Folder that contains files used by the album function
Album HTML file
File used by the album function
(File Name Extension: HTM)
VIEWING IMAGES ON A COMPUTER
211
FAVORITE folder
Folder that contains Favorites image files
(Image Size: 320 x 240 pixels)
DPOF file folder
Folder that contains DPOF files
TIFF Data Folder
Folder that contains All TIFF format image related files
TIFF Image Folder
Folder that contains TIFF format image files
TIFF Image File
File that contains a TIFF format image (File Name
Extension: TIF).
BESTSHOT folder (Built-in memory only)
Folder that contains BESTSHOT user setup files.
User setup files (Built-in memory only)
Files that contain BESTSHOT user setups
Image Files Supported by the Camera
Image files recorded with this camera
DCF protocol image files
Certain DCF functions may not be supported. When
displaying an image recorded on another camera model, it
may take a long time for the image to appear on the
display.
VIEWING IMAGES ON A COMPUTER
212
Built-in Memory and Memory Card
Precautions
Note that the folder named DCIM is the parent (top)
folder of all the files in memory. When transferring
memory contents to a hard disk, CD-R, MO disk, or other
external storage, treat all the contents inside a DCIM
folder as a set and always keep them together. You can
change the name of the DCIM folder on your computer.
Changing the name to a date is a good way to keep track
of multiple DCIM folders. However, if you even want to
copy the folders back to the cameras file memory, be
sure you change the name of the DCIM folder back to
DCIM first. The camera does not recognize any folder
name other than DCIM.
USING THE CAMERA WITH A COMPUTER
213
Creating an album
IMPORTANT!
Remember that creating an ALBUM folder (page
209) causes different size versions of each image to
be created in memory. If there is an ALBUM folder
in image memory when you specify printing of all
images by a professional print service or on a printer,
you may end up with unwanted multiple prints of the
same image. To avoid this problem, use the
procedure under To delete an album on page 221
to delete the ALBUM folder.
USING THE CAMERA WITH A COMPUTER
The album feature of the camera creates files that make it
possible for you to view images on your computer in a
photo album layout. You can also use the applications
contained on the CD-ROM that comes bundled with the
camera to automate image transfer and to retouch images.
Using the Album Feature
The album feature creates an HTML photo album layout
that displays your images. You can use the HTML layout to
post your images on a Web page, or for printing the
images.
You can use the Web browser shown below to view or
print the contents of an album. Note that to view a movie
on a computer running Windows 2000 or 98, you need to
install DirectX.
Microsoft Internet Explorer Ver 5.5 or later
Album
Index Info
USING THE CAMERA WITH A COMPUTER
214
1.
In the PLAY mode, press [MENU].
2.
Select the “PLAY
tab, select “Create
Album”, and then
press [].
3.
Use [] and [] to select “Create”, and then
press [SET].
This starts creation of the album, and causes the
message Busy.... Please wait.... to appear on the
monitor screen.
The PLAY mode screen reappears after creation of
the album is complete.
Creating an album causes a file folder named
ALBUM, which contains a file named INDEX.HTM
plus other files to be created in camera memory or
on the memory card.
Sample layout
IMPORTANT!
Never open the battery compartment cover or
remove the memory card from the camera while an
album is being created. Doing so not only runs the
risk of certain album files being skipped, it can also
result in image data and other data in memory being
corrupted.
If memory becomes full while an album is being
created, the message Memory Full appears on the
monitor screen and album creation is terminated.
Album creation will not be performed properly if the
battery goes dead while album creation is in
progress.
You can also configure the camera to create albums
automatically (page 217). However, performing the
above procedure creates an album regardless of
whether automatic album creation is turned on or off.
Images in the ALBUM folder (page 209) cannot be
viewed on the cameras monitor screen.
USING THE CAMERA WITH A COMPUTER
215
Selecting an Album Layout
You can select from among 10 different display layouts for
an album.
1.
In the PLAY mode, press [MENU].
2.
Select the “PLAY” tab, select “Create
Album”, and then press [].
3.
Use [] and [] to select “Layout”.
4.
Use [] and [] to select the layout you want.
Changing the layout causes the layout sample on the
right side of the screen to change.
IMPORTANT!
The sample layout shows the arrangement of items
and the background color. It does not show whether
the layout uses a list view or detailed view, or the
current Image Type setting.
Configuring Detailed Album Settings
1.
In the PLAY mode, press [MENU].
2.
Select the “PLAY” tab, select “Create
Album”, and then press [].
3.
Use [] and [] to select “Set Up”, and then
press [].
4.
Use [] and [] to
select the item whose
setting you want to
change, and then press
[].
Details about each of the
settings are provided in
the following sections.
5.
Use [] and [] to change the setting, and
then press [SET].
USING THE CAMERA WITH A COMPUTER
216
Background Color
You can specify white, black, or gray as the color of the
album background using the procedure under Configuring
Detailed Album Settings.
Album Type
There are two album types: Normal and Index/Info.
Normal Type : This type of album displays images in
accordance with the currently selected
layout.
Index/Info Type : In addition to the normal album screen,
this type of album also includes
thumbnails of images and detailed
information about each image.
Image Use
This setting lets you select from among three different
image uses, as described below. Select the image use that
best suits the way you plan to use the image.
Select this
setting:
View
WEB
Print
For this purpose:
Smaller images for album browsing, Website
thumbnails, or archiving on a CD-R or other
media, with the full-size image displayed
when a thumbnail is clicked
This setting can be used for browsing with
the thumbnails. Clicking a thumbnail
displays a larger version for viewing or
printing.
Small image files only for album browsing, or
uploading to a Website, etc.
This option displays only the small-file
images (located in the cameras ALBUM
folder). Smaller files upload to the Internet
faster.
You cannot enlarge images by clicking a
thumbnail or play movies while this image is
selected.
Printing (high resolution)
High-resolution images take longer to
display on your computer screen.
You cannot enlarge images by clicking a
thumbnail or play movies while this image is
selected.
USING THE CAMERA WITH A COMPUTER
217
Auto Album Creation On/Off
This setting controls whether an album is created
automatically whenever you turn off the camera.
Select this option:
On
Off
To do this:
Turn on auto album creation
Turn off auto album creation
When auto album creation is turned on, an album is
created automatically in built-in memory or on the
memory card whenever you turn off the camera.
IMPORTANT!
When you turn off the camera while auto album
creation is turned on, the monitor screen turns off,
but the green operation lamp continues to flash for a
few seconds to indicate that the album creation
process is being performed. Never open the battery
compartment cover or remove the memory card
while the green operation lamp is flashing.
NOTE
Depending on the number of images in memory, it
can take quite a bit of time to complete auto album
creation when you turn off the camera. If you do not
plan to use the album feature, we suggest that you
keep auto album creation turned off, which shortens
the amount of time the camera takes to power down
completely.
USING THE CAMERA WITH A COMPUTER
218
Viewing Album Files
You can view and print album files using your computers
Web browser application.
1.
Use your computer to access the data in built-
in memory or on the memory card, or access
a memory card with your computer (pages
198, 208).
2.
Open the built-in memory “ALBUM” folder or
the memory card “ALBUM” folder, which is
located inside the folder named “DCIM”.
3.
Use your computer’s
Web browser to open
the file named
INDEX.HTM”.
This displays a list of
folders in built-in memory
or on the memory card.
Index/Info Album Type
File NameImage
4.
If you created the album after selecting
Index/Info” as the album type under
Configuring Detailed Album Settings” on
page 215, you can click one of the following
display options.
Album: Displays an album created by the camera.
Index : Displays a list of images stored in a folder.
Info : Displays information about each image.
If View is selected for Use (page 216), you can
double-click an image on your computer screen to
display the full-size version.
Album
USING THE CAMERA WITH A COMPUTER
219
Index
Info
The following describes the information that appears
on the Info Screen.
This Info Screen item: Shows this:
File Size Image file size
Resolution Resolution
Quality Quality
Recording mode Recording mode
AE Exposure mode
Drive mode Drive mode
Light metering Metering mode
Shutter speed Shutter speed
Aperture stop Aperture stop
Exposure comp EV shift
Focusing mode Focusing mode
AF Area Auto Focus area
Flash mode Flash mode
Sharpness Sharpness
Saturation Saturation
Contrast Contrast
White balance White balance
Sensitivity Sensitivity
Filter Filter setting
Enhancement Enhancement setting
Flash intensity Flash intensity
USING THE CAMERA WITH A COMPUTER
220
NOTES
When printing an album page, you should set up
your Web browser as described below.
Select the browser frame where the images are
located.
Set margins to the lowest possible values.
Set the background color to a printable color.
See the user documentation that came with your
Web browser application for details about printing
and configuring settings for printing.
Album contents (titles, comments, etc.) cannot be
edited on the camera. Use a commercially available
HTML file editor to edit album contents.
5.
After you are finished viewing the album, exit
your Web browser application.
Saving an Album
To save an album, copy the DCIM folder from camera
memory or the memory card to your computers hard disk,
a CD-R, an MO disk, or some other storage medium.
Note that copying only the ALBUM folder, does not copy
image data and other necessary files.
After copying the DCIM folder, do not change or delete
any of the files inside of it. Adding new images or deleting
existing images may lead to abnormal album display.
If you plan to use a memory card again after saving its
album, first delete all of its files or format it before loading
it into the camera.
When you have WEB selected for the Use setting, the
album shows only the smaller image files stored in the
ALBUM folder. Such images can be uploaded to the
Internet more quickly.
This Info Screen item: Shows this:
Digital zoom Digital zoom setting
World Location
Date Recording date and time
Model Camera model name
USING THE CAMERA WITH A COMPUTER
221
To delete an album
1.
In the PLAY mode, press [MENU].
2.
Select the “PLAY” tab, select “Create Album”,
and then press [].
3.
Use [] and [] to select “Delete”, and then
press [SET].
This deletes the album and returns to the PLAY
mode screen.
Installing the Software from the CD-ROM
Your digital camera comes bundled with useful applications
for using it in combination with a computer. Install the
applications you need on your computer.
About the bundled CD-ROM (CASIO
Digital Camera Software)
The CD-ROM (CASIO Digital Camera Software) that
comes bundled with the camera contains the applications
described below. Installation of these applications is
optional, and you should install only the ones you want to
use.
USB Driver for Mass Storage (for Windows)
This is the software that makes it possible for the camera
to talk to your personal computer over a USB connection.
If you are using Windows XP, do not install the USB driver
from the CD-ROM. With these operating systems, you will
be able to perform USB communication simply by
connecting the camera to your computer with the USB
cable.
USING THE CAMERA WITH A COMPUTER
222
Photo Loader (for Windows/Macintosh)
This application automatically transfers image, audio
snapshot, and voice recording WAV files from the camera
to your computer. Photo Loader automatically stores
transferred files in folders named using the current date
(year, month, day) and generates HTML files that make it
possible to view images using a web browser. Photo
Loader (Windows version only) also includes a feature that
simplifies the task of attaching images to e-mail.
See the user documentation file (PDF) on the bundled
CASIO Digital Camera Software CD-ROM for details
about using Photo Loader.
Photohands (for Windows)
Photohands includes retouching tools for adjusting image
color, contrast, and brightness, for resizing images, for
changing image orientation, and for cropping images. You
can also use Photohands for printing images and for
adding a date stamp to printed images.
See the user documentation file (PDF) on the bundled
CASIO Digital Camera Software CD-ROM for details
about using Photohands.
DirectX (for Windows)
This software provides an extended tool set including a
codec that allows Windows 98 and 2000 to handle movie
files recorded using a digital camera. You do not need to
install DirectX if you are running Windows XP or Me.
Acrobat Reader (for Windows)
This is an application that lets you read PDF files. Use it to
read the user documentation for the camera, Photo Loader,
and Photohands, all of which is included on the bundled
CD-ROM.
See the user documentation files (PDF) on the bundled
CD-ROM for details about using Photo Loader and
Photohands. See Viewing User Documentation (PDF
files) on page 226 (Windows) and page 228 (Macintosh)
of this manual for more information.
USING THE CAMERA WITH A COMPUTER
223
Photohands
XP/2000/Me/98
Pentium or
higher
At least 64MB
At least 10MB
Computer System Requirements
Computer system requirements depend on each of the
applications, as described below.
Windows
*1In the case of Windows 2000, you install a data file that enables
use of the operating systems standard USB driver. You do not
install a special USB driver. Proper operation is not guaranteed
on a computer that has been upgraded from Windows 95 or 3.1
to Windows Me or 98, or from Windows 95 or NT to Windows
2000.
*2With Windows XP, use the USB driver that comes with the
operating system. You do not need to install the USB driver that
comes with the camera.
Macintosh
Photo Loader
9
Power PC
At least 32MB
At least 3MB
USB connection is supported on a Macintosh running OS 9, 10.1,
or 10.2. Operation is supported using the standard USB driver
that comes with the operating system, so all you need to do is
connect the camera to your Macintosh using the USB cable.
OS
CPU
Memory
HD
USB Driver*1
XP*2/2000/Me/
98
486 or higher
(Pentium
recommended)
Photo Loader
XP/2000/Me/98
486 or higher
(Pentium
recommended)
At least 16MB
At least 7MB
OS
CPU
Memory
HD
USING THE CAMERA WITH A COMPUTER
224
IMPORTANT!
For details about Windows minimum system
requirements, see the Readme file on the CD-ROM
(CASIO Digital Camera Software) that comes
bundled with the camera.
For details about Macintosh minimum system
requirements, use a Web browser application to read
the contents of the readme file on the CD-ROM
(CASIO Digital Camera Software) that comes
bundled with the camera.
The software on the CD-ROM (CASIO Digital
Camera Software) that comes bundled with the
camera does not support operation under Mac OS X
(10.0).
Installing Software from the CD-ROM in
Windows
Use the procedures in this section to install the software
from the bundled CD-ROM (CASIO Digital Camera
Software) to your computer.
NOTE
If you already have one of the bundled applications
installed on your computer, check its version. If the
bundled version is newer than the one you have, you
should install the newer version.
The CD-ROM (CASIO Digital Camera Software) includes
the software and user documentation for various
languages. Check the CD-ROM menu screen to see if
applications and user documentation are available for a
particular language.
USING THE CAMERA WITH A COMPUTER
225
Getting Started
Start up your computer and insert the CD-ROM into its CD-
ROM drive. This will automatically launch the menu
application, which displays a menu screen on your
computer.
The menu application may not start up automatically on
some computers. If this happens, navigate to the CD-
ROM and double-click menu.exe to launch the menu
application.
Selecting a Language
First select a language. Note that some software is not
available in all languages.
1.
On the menu screen, click the tab for the
language you want.
Viewing the Contents of the Read me”
File
You should always read the Read me file for any
application before installing it. The Read me file contains
information you need to know when installing the
application.
1.
Click the “Read me” button for the application
you are going to install.
IMPORTANT!
Before upgrading or reinstalling Photo Loader, or
before installing it onto another computer, be sure to
read the Read me file for information about
retaining existing libraries.
USING THE CAMERA WITH A COMPUTER
226
Installing an Application
1.
Click the “Install” button for the application
you want to install.
2.
Follow the instructions that appear on your
computer screen.
IMPORTANT!
Be sure to follow the instructions carefully and
completely. If you make a mistake when installing
Photo Loader, you may not be able to browse your
existing library information and HTML files that are
created automatically by Photo Loader. In some
cases, image files may be lost.
When using an operating system other than
Windows XP, never connect the camera to your
computer without installing the USB driver from the
CD-ROM first.
Viewing User Documentation (PDF Files)
1.
In the “Manual” area, click the name of the
manual you want to read.
IMPORTANT!
You need to have Adobe Acrobat Reader installed
on your computer to read user documentation files. If
you do not already have Adobe Acrobat Reader
installed, you can install it from the bundled CD-
ROM.
USING THE CAMERA WITH A COMPUTER
227
User Registration
You can perform user registration over the Internet. To do
so, of course, you need to be able to connect to the
Internet with your computer.
1.
Click the “Register” button.
This starts up your Web browser and accesses the
user registration website. Follow the instructions that
appear on your computer screen to register.
2.
After registering, terminate your connection
to the Internet.
Exiting the Menu Application
1.
On the menu screen, click “Exit” to exit the
menu.
Installing Software from the CD-ROM on a
Macintosh
Use the procedures in this section to install the software
from the bundled CD-ROM (CASIO Digital Camera
Software) to your computer.
Installing Software
Use the following procedures to install the software.
USING THE CAMERA WITH A COMPUTER
228
To install Photo Loader
1.
Open the folder named “Photo Loader”.
2.
Open the folder named “English”, and then
open the file named “Important”.
3.
Open the folder named “Installer”, and then
open the file named “readme”.
4.
Follow the instructions in the “readme” file to
install Photo Loader.
IMPORTANT!
If you are upgrading to the new version of Photo
Loader from a previous version and you want to use
library management data and HTML files created
using the old version of Photo Loader, be sure to
read the Important file in the Photo Loader folder.
Follow the instructions in the file to use your existing
library management files. Failure to follow this
procedure correctly can result in loss or corruption of
your existing files.
Viewing User Documentation (PDF Files)
To perform the following procedures, you must have
Acrobat Reader installed on your Macintosh. You can
download the latest version of Adobe Acrobat Reader by
visiting the Adobe Systems website.
To view the camera user’s guide
1.
On the CD-ROM, open the “Manual” folder.
2.
Open the “Digital Camera” folder, and then
open the folder for the language whose user’s
guide you want to view.
3.
Open the file named “camera_xx.pdf”.
•“xx is the language code.
USING THE CAMERA WITH A COMPUTER
229
To read the Photo Loader user’s guide
1.
On the CD-ROM, open the “Manual” folder.
2.
Open the “Photo Loader” folder and then
open the “English” folder.
3.
Open “PhotoLoader_english”.
To register as a user
Internet registration only is supported. Visit the following
CASIO website to register:
http://world.casio.com/qv/register/
APPENDIX
230
APPENDIX
Menu Reference
The following shows lists of menus that appear in the REC
mode and PLAY mode, and their settings.
The settings that are underlined in the following table are
initial defaults.
REC mode
REC tab menu
2816 x 2112 / 2816 x 1872 (3:2) /
2048 x 1536 / 1600 x 1200 / 1280 x 960 /
640 x 480
Fine / Normal / Economy / TIFF
2.0 / 1.7 / 1.3 / 1.0 / 0.7 / 0.3 / 0.0 /
+0.3 / +0.7 / +1.0 / +1.3 / +1.7 / +2.0
Auto / (Daylight) / (Cloudy) /
(Shade) / (Tungsten) /
1 (Fluorescent 1) / 2 (Fluorescent 2) /
(Flash) / Manual
Auto / ISO 50 / ISO 100/ ISO 200 / ISO 400
Hybrid / Continuous / Contrast
Spot / Multi / Free
Multi / Center weighted / Spot
On / Off
Size
Quality
EV Shift
White Balance
ISO
AF Mode
AF Area
Metering
Audio Snap
Filter
Sharpness
Saturation
Contrast
Flash Intensity
Grid
Digital Zoom
Review
L/R Key
Off / B/W / Sepia / Red / Green / Blue /
Yellow / Pink / Purple
Hard / Normal / Soft
High / Normal / Low
High / Normal / Low
Strong / Normal / Weak
On / Off
On / Off
On / Off
EV shift / White Balance / ISO / Metering /
AF Area / Off
APPENDIX
231
Memory tab menu
Flash
Focus
White Balance
ISO
AF Area
Metering
Cont. / BKT
Flash Intensity
Digital Zoom
MF Position
Zoom Position
On / Off
On / Off
On / Off
On / Off
On / Off
On / Off
On / Off
On / Off
On / Off
On / Off
On / Off
Sounds
Startup
File No.
World Time
Date Style
Adjust
Language
Sleep
Auto Power Off
USB
Video Out
Format
Reset
Startup / Half Shutter /Shutter / Operation /
Volume
On (Selectable image) / Off
Continue / Reset
Home / World
Home Time setup (city, DST, etc.)
World Time setup (city, DST, etc.)
YY/MM/DD / DD/MM/YY / MM/DD/YY
Time setting
/ English / Français / Deutsch /
Español / Italiano / Português / /
/
30 sec / 1 min / 2 min / Off
2 min / 5 min
Mass Storage (USB DIRECT- PRINT) /
PTP (PictBridge)
NTSC / PAL
Format / Cancel
Reset / Cancel
Set Up tab menu
APPENDIX
232
Start / Images / Time / Interval / Cancel
Show / Save / Cancel
Select images / All images / Cancel
On / All Files : On / Cancel
Rotate / Cancel
1600 x 1200 / 1280 x 960 / 640 x 480 /
Cancel
Create / Delete / Layout / Set Up / Cancel
Alarm setups
Built-in Card / Card Built-in / Cancel
PLAY mode
PLAY tab menu
Slideshow
Calendar
Favorites
DPOF
Protect
Rotation
Resize
Trimming
Create Album
Dubbing
Alarm
Copy
Set Up tab menu
Sounds
Startup
File No.
World Time
Date Style
Adjust
Language
Sleep
Auto Power Off
USB
Video Out
Format
Reset
Startup / Half Shutter /Shutter / Operation /
Volume
On (Selectable image) / Off
Continue / Reset
Home / World
Home Time setup (city, DST, etc.)
World Time setup (city, DST, etc.)
YY/MM/DD / DD/MM/YY / MM/DD/YY
Time setting
/ English / Français / Deutsch /
Español / Italiano / Português / /
/
30 sec / 1 min / 2 min / Off
2 min / 5 min
Mass Storage (USB DIRECT- PRINT) /
PTP (PictBridge)
NTSC / PAL
Format / Cancel
Reset / Cancel
APPENDIX
233
Indicator Lamp Reference
The camera has three indicator lamps: a green operation
lamp, a red operation lamp, and a self-timer lamp. These
lamps light and flash to indicate the current operational
status of the camera.
*There are three lamp flash patterns. Pattern 1 flashes once per
second, Pattern 2 flashes twice per second, and Pattern 3 flashes
four times per second. The table below explains what each flash
pattern indicates.
Self-timer lampGreen operation lamp
BKT
AE-L
Red operation lamp
REC mode
Operation Lamp
Self-timer
Lamp
Green
Lit
Lit
Pattern 3
Lit
Pattern 2
Pattern 1
Red
Pattern 3
Lit
Pattern 1
Pattern 2
Lit
Red
Pattern 1
Pattern 2
Operational (Power on, recording
enabled)
Flash is charging.
Flash charging is complete.
Auto Focus operation was successful.
Cannot Auto Focus.
Monitor screen is off.
Storing image
Storing movie / performing noise
reduction
Self-timer countdown
(10 to 3 seconds)
Self-timer countdown
(3 to 0 seconds)
Cannot charge flash.
Memory card problem / Memory
card is unformatted. / BESTSHOT
setup cannot be registered.
Memory card is locked. / Cannot
create folder. / Memory is full. /
Write error
Meaning
APPENDIX
234
Operation Lamp
Self-timer
Lamp
Green Red Red
Meaning
Pattern 3
Pattern 3
Pattern 3
Low battery alert
Formatting card
Powering down
IMPORTANT!
When you are using a memory card, never remove
the card from the camera while the green operation
lamp is flashing. Doing so will cause recorded
images to be lost.
PLAY mode
Operation Lamp
Self-timer
Lamp
Green
Lit
Pattern 3
Red
Pattern 2
Lit
Pattern 3
Red
Operational (Power on, recording
enabled)
One of the following operations is
being performed: delete, DPOF,
image protect, copy, album creation,
format, power down
Memory card problem / Memory
card is unformatted.
Memory card is locked. / Cannot
create folder. / Memory is full.
Low battery alert
Meaning
APPENDIX
235
Rapid Charger Unit
The rapid charger unit has a [CHARGE] lamp that lights or
flashes in accordance with the charger unit operation that
is being performed.
[CHARGE] Lamp
Color
Red
Status
Meaning
Green
Red
Amber
Lit
Lit
Flashing
Lit
Charging
Charging complete
Charger unit or battery abnormality
Charge standby state (Ambient temperature is
too high or too low.)
[CHARGE] lamp [CHARGE] lamp
APPENDIX
236
Power does not turn on.
Camera suddenly powers
down.
Image is not recorded
when the shutter button is
pressed.
1) The battery is not oriented correctly.
2) The battery is dead.
1) Auto Power Off activated (page 47).
2) The battery is dead.
1) The camera is in the PLAY mode.
2) Flash unit is being charged.
3) Memory is full.
1) Orient the battery correctly (page 38).
2) Charge the battery (page 35). If the battery goes
dead soon after being charged, it means the
battery has reached the end of its life and needs
to be replaced. Purchase a separately available
NP-40 rechargeable lithium ion battery.
1) Turn power back on.
2) Charge the battery (page 35).
1) Use the mode dial to select the REC mode
(page 24).
2) Wait until the flash unit finishes charging.
3) Transfer files you want to keep to your
computer and then delete files from image
memory, or use a different memory card.
Power Supply
Image Recording
Symptom Possible Cause Action
Troubleshooting Guide
APPENDIX
237
1) Clean the lens.
2) Clean the phase differential sensor.
3) Move your finger so it does not block the phase
differential sensor.
4) Make sure the subject is centered in the focus
frame when composing the image.
5) Use manual focus (page 77).
6) Mount the camera on a tripod.
7) Change the Auto Focus mode setting to
Contrast (page 118).
When composing the image, make sure the
subject on which you want to focus is located
inside the focus frame.
1) Select a different flash mode (page 64).
2) Charge the battery (page 35).
3) Select a different REC mode.
4) Select a different flash mode (page 64) or
BESTSHOT scene (page 103).
1) The lens is dirty.
2) The phase differential sensor is dirty.
3) You are blocking the phase differential sensor
with your finger.
4) The subject is not located in the center of the
focus frame when you compose the image.
5) The subject you are shooting is a type that is
not compatible with Auto Focus operation (page
58).
6) You are moving the camera.
7) An Auto Focus mode other than Contrast is
selected while a conversion lens is installed on
the camera (page 118).
The image is not focused properly.
1) (flash off) is selected as the flash mode.
2) The battery is dead.
3) The camera is in the Movie mode.
4) A scene that selects (flash off) as the flash
mode is selected in the BESTSHOT Mode.
Auto Focus does not focus
properly
The subject is out of focus
in the recorded image.
The flash does not fire.
Image Recording
Symptom Possible Cause Action
APPENDIX
238
Camera powers down
during self-timer
countdown.
Monitor screen image is
out of focus.
Recorded images are not
saved in memory.
The images produced by
an auto bracketing
operation look the same.
The battery is dead.
1) You are using the Manual Focus Mode and
have not focused the image.
2) You are trying to use the Macro Mode ( )
when shooting a scenery or portrait shot.
3) You are trying to use Auto Focus or the Infinity
Mode ( ) when shooting a close-up shot.
1) Camera powers down before the save
operation is complete.
2) Removing the memory card before the save
operation is complete.
1) The subject you are recording is a type for
which the different settings do not produce
much of a difference in appearance.
2) The image is drastically under-exposed or
over-exposed.
Charge the battery (page 35).
1) Focus the image (page 78).
2) Use Auto Focus for scenery and portrait shots.
3) Use the Macro Mode ( ) for close-ups.
1) When the battery indicator shows , charge
the battery as soon as possible (page 35).
2) Do not remove the memory card before the
save operation is complete.
1) Shoot a different subject.
2) Adjust the exposure.
Symptom Possible Cause Action
Image Recording
APPENDIX
239
Position the camera so sunlight does not shine
directly into the lens.
This camera cannot display non-DCF images
recorded onto a memory card using another digital
camera.
Remove the battery from the camera, reinsert it,
and then try again.
1) After confirming that the computer is not
accessing camera memory, disconnect the USB
cable.
2) Press [DISP] to turn on the monitor screen.
3) Unplug the AV cable.
1) Check all connections.
2) Install the USB driver on your computer (page
198).
3) Turn on the camera.
Color of the playback
image is different from the
image on the monitor
screen during recording.
Images are not displayed.
All buttons and switches
are disabled.
Monitor screen is off.
Cannot transfer files over a
USB connection.
Sunlight or light from another source is shining
directly into the lens during recording.
A memory card with non-DCF images recorded
with another camera is loaded in the camera.
Circuit problem caused by electrostatic charge,
impact, etc. while the camera was connected to
another device.
1) USB communication is in progress.
2) The monitor screen is turned off (in the REC
mode).
3) The camera is connected to a TV for image
output.
1) USB cable is not connected securely.
2) USB driver is not installed.
3) Camera is turned off.
Other
Symptom Possible Cause Action
Playback
APPENDIX
240
If you have problems installing the USB driver...
You may not be able to install the USB driver properly if you use the USB cable to connect the camera to a computer running
Windows 98 before installing the USB driver from the bundled CD-ROM (CASIO Digital Camera Software), or if you have
another type of driver installed. This will make it impossible for the computer to recognize the digital camera when it is
connected. If this happens, you will need to re-install the cameras USB driver. For information about how to re-install the USB
driver, see the USB drivers Read me file on CASIO Digital Camera Software CD-ROM that comes bundled with the
camera.
APPENDIX
241
Display Messages
Alarm setting
complete.
Battery is low.
Can not find the file.
Cannot register any
more files.
Card ERROR
File could not be
saved because
battery is low.
This message appears after you change the alarm
setting.
The battery is dead.
The camera cannot find the image specified by the
slideshow Images setting. Specify another image
(page 150).
You are attempting to register a BESTSHOT
setup when the SCENE folder already contains
999 setups.
You are attempting to register a FAVORITE file
when the FAVORITE folder already contains
9999 files.
Some problem occurred with the memory card.
Turn off the camera, and remove and then reinsert
the memory card. If the same message appears,
format the memory card (page 184).
IMPORTANT!
Formatting the memory card deletes all files on
the memory card. Before formatting, try
transferring recoverable files to a computer or
some other storage device.
The battery is dead, so the recorded image could
not be saved.
Folder cannot be
created.
LENS ERROR
Memory Full
No Favorites file!
Printing Error
Record Error
SYSTEM ERROR
This message appears when you try to record an
image while there are 9,999 files stored in the
999th folder. If you want to record more files,
delete files you no longer need (page 159).
If the lens comes into contact with some obstacle
while it is extending, this message appears, the
lens retracts, and the camera turns off. Take action
to remove the obstacle, and try turning on power
again.
Memory is full. If you want to record more files,
delete files you no longer need (page 159).
There is no FAVORITE file.
One of the following problems occurred during
printing.
Printer power off
Out of paper
Out of ink
Printer internal error
Image compression could not be performed during
image data storage for some reason. Record the
image again.
Your camera system is corrupted. Contact your
retailer or a CASIO service center.
APPENDIX
242
The LOCK switch of the SD memory card is
locked. You cannot store images to or delete
images from a memory card that is locked.
There are no files in built-in memory or on the
memory card.
There are no DPOF settings specifying images and
the number of copies of each for printing.
Configure the required DPOF settings (page 189).
You are trying to save an invalid file as a
BESTSHOT user setup, or as an original startup
image.
The memory card is not formatted. Format the
memory card (page 184).
The image file or audio file is corrupted, or is a
type that cannot be displayed by this camera.
You attempted to copy files from built-in memory to
a memory card while there is no memory card
loaded in the camera (page 183).
The function you are trying to perform is not
supported for the file on which you are trying to
perform it.
The card is locked.
There are no files.
There are no printing
images.
Set up DPOF.
There is no file to
register.
This card is not
formatted.
This file cannot be
played.
This function cannot
be used.
This function is not
supported for this
file.
Specifications
Product ............................... Digital Camera
Model .................................. EX-P600
Camera Functions
Image Files Format
Snapshots ....................... JPEG (Exif Ver.2.2); DCF (Design rule
for Camera File system) 1.0 standard;
DPOF compliant
Movies ............................. AVI (Motion JPEG)
Audio ............................... WAV
Recording Media ............... 9.2MB built-in Flash memory
SD Memory Card
MultimediaCard
Image Size
Snapshots ...................... 2816 x 2112 pixels
2816 x 1872 (3:2) pixels
2048 x 1536 pixels
1600 x 1200 pixels
1280 x 960 pixels
640 x 480 pixels
Movies ............................ 320 x 240 pixels
APPENDIX
243
Approximate Memory Capacity and File sizes:
Snapshots
File Size
(pixels)
2816 x 2112
2816 x 1872
(3:2)
2048 x 1536
1600 x 1200
(UXGA)
1280 x 960
(SXGA)
640 x 480
(VGA)
Quality
Fine
Normal
Economy
TIFF
Fine
Normal
Economy
TIFF
Fine
Normal
Economy
TIFF
Fine
Normal
Economy
TIFF
Fine
Normal
Economy
TIFF
Fine
Normal
Economy
TIFF
Approximate
Image File Size
3.0MB
2.4MB
1.6MB
17.0MB
2.7MB
2.1MB
1.4MB
15.1MB
1.64MB
1.23MB
630KB
9.0MB
1.05MB
710KB
370KB
5.5MB
680KB
460KB
250KB
3.5MB
190KB
140KB
90KB
900KB
Built-in flash
memory 9.2MB
2 shots
3 shots
5 shots
0 shots
3 shots
4 shots
6 shots
0 shots
5 shots
6 shots
13 shots
0 shots
7 shots
11 shots
23 shots
1 shots
12 shots
18 shots
33 shots
2 shots
44 shots
57 shots
92 shots
8 shots
SD Memory
Card* 64MB
19 shots
24 shots
36 shots
3 shots
22 shots
28 shots
41 shots
3 shots
34 shots
45 shots
88 shots
5 shots
53 shots
79 shots
154 shots
9 shots
82 shots
126 shots
221 shots
14 shots
294 shots
386 shots
618 shots
55 shots
Movies (320 x 240 pixels)
*Based on Matsushita Electric Industrial Co., Ltd. products. Capacity
depends on card manufacturer.
*To determine the number of images that can be stored on a memory card of a
different capacity, multiply the capacities in the table by the appropriate value.
Delete .................................. Single-file, all files (with protection)
Effective Pixels .................. 6.0 million
Imaging Element ................ 1/1.8-inch square pixel color CCD
(Total pixels: 6.37 million)
Lens/Focal Distance
Lenses ............................. Six lenses in five groups, including an
aspherical lens
F2.8 (W) to 4 (T); f=7.1 (W) to 28.4mm
(T) (equivalent to approximately 33
(W) to 132 (T) for 35mm film)
Zoom ................................... 4X optical zoom; 4X digital zoom
(16X in combination with optical zoom)
Focusing ............................. Combination phase differential sensor
and contrast Auto Focus (AF Mode
(AF Area: Spot, Multi, or Free), Macro
Mode), Infinity Mode; Manual Focus;
focus lock
Data Size
Recording
Time
300KB/second max.
Total Movie Time:
30 seconds maximum (built-in memory)
200 seconds maximum (SD 64MB memory card)*
APPENDIX
244
Approximate Focus Range (from lens surface)
Normal ............................. 40cm to (1.3´ to )
Macro .............................. Approximately 10cm to 50cm
(3.9˝ to 19.7˝) at wide angle
Approximately 40cm to 50cm
(15.6˝ to 19.7˝) at telephoto
Exposure Control
Light Metering ................. Multi-pattern by CCD
Exposure ......................... Program AE, Aperture priority AE,
Shutter speed priority AE, Manual
exposure
Exposure Compensation .....
2EV to +2EV (1/3EV units)
Shutter ................................ CCD electronic shutter; mechanical
shutter, Snapshot Mode, Aperture
Priority AE Mode, BESTSHOT Mode :
1/8 to 1/2000 second
Shutter Speed Priority AE Mode,
Manual Exposure Mode : BULB, 60 to
1/2000 second
Shutter speed is different for the
following BESTSHOT scenes.
Night Scene: 4 to 1/2000 second
Fireworks: BULB, 60 to 1/2000
second
Aperture .............................. F2.8, 3.2, 3.5, 4.0, 4.5, 5.0, 5.6, 6.3,
7.1, 8.0
Using optical zoom causes the
aperture to change.
An aperture setting from F2.8 to 5.6
is possible in the Snapshot Mode
White Balance .................... Automatic, fixed (7 modes), manual
switching
Self-timer ............................ 10 seconds, 2 seconds, Triple Self-
timer, Remote controller, Remote
controller and 2-second Self-timer
Built-in Flash
Flash Modes .................... AUTO, ON, OFF, Red eye reduction
Flash Range .................... Wide Angle Optical Zoom: 0.2 to 2.9
meters (0.66´ to 9.5´)
Telephoto Optical Zoom: 0.4 to 2.0
meters (1.3´ to 6.6´)
(ISO Sensitivity: Auto)
Recording Functions ........ Snapshot with audio; Macro; self-timer;
Aperture priority AE; Shutter speed
priority AE; Manual exposure;
BESTSHOT; Continuous shutter; Auto
Bracketing; Movie with audio; voice
recording
* Audio recording is monaural.
Audio Recording Time
Audio Snapshot ............... Approximately 30 seconds maximum
per image
Voice Recording .............. Approximately 40 minutes with built-in
memory
After Recording ............... Approximately 30 seconds maximum
per image
APPENDIX
245
Monitor Screen .................. 2.0-inch TFT color LCD
115,200 pixels (480 x 240)
Viewfinder .......................... Monitor screen and optical viewfinder
Timekeeping Functions .... Built-in digital quartz clock
Date and Time ................ Recorded with image data
Auto Calendar ................. To 2049
World Time ...................... City; Date; Time; Summer time;
162 cities in 32 time zones
Input/Output Terminals .... AC adaptor connector (DC IN); USB /
AV port (Special mini port, NTSC/
PAL); External flash sync terminal
Microphone ........................ Monaural
Speaker ............................... Monaural
Supported Battery: NP-40 (Rated Capacitance: 1230mAh)
Storage Medium: SD Memory Card
*1 Number of Shots (CIPA)
CIPA Standard
Temperature: 23°C (73°F)
Monitor Screen: On
Zoom operation between full wide to full telephoto every 30 seconds,
during which two images are recorded, one image with flash; power
turned off and back on every time 10 images are recorded.
Power Requirements
Power Requirements ........ Rechargeable lithium ion battery
(NP-40) x 1
AC adaptor (AD-C40)
Approximate Battery Life:
The values below indicate the amount of time under the conditions defined
below, until power automatically turns off due to battery failure. They do not
guarantee that you will be able to achieve this level of operation. Low
temperatures shorten battery life.
Apporoximate Battery Life
260 shots (130 minutes)
600 shots (150 minutes)
300 minutes
260 minutes
Operation
Number of Shots (CIPA)*1
(Operating Time)
Number of Shots, Continuous Recording*2
(Operating Time)
Continuous Playback*3
(Continuous Snapshot Recording)
Continuous Voice Recording*4
APPENDIX
246
*2 Continuous Recording Conditions
Temperature: 23°C (73°F)
Monitor screen: On
Flash: Off
Image recorded approximately every 15 seconds
*3 Continuous Playback Conditions
Temperature: 23°C (73°F)
Scroll one image about every 10 seconds
*4 Voice recording times are based on continuous recording.
Power Consumption ......... DC 4.5V Approximately 5.5W
Dimensions ........................ 97.5(W) x 67.5(H) x 45.1(D) mm
(3.8˝(W) x 2.7˝(H) x 1.8˝(D))
(excluding projections; 26.1mm (1.0˝)
at thinnest part)
Weight ................................. Approximately 225 g (7.9 oz)
(excluding battery and accessories)
Bundled Accessories........ Rechargeable lithium ion battery (NP-
40); Rapid charger unit (BC-30L); Card
Remote Controller; lithium battery
(CR2025); AC power cord; USB cable;
AV cable; Strap; CD-ROM; Basic
Reference
Rechargeable Lithium Ion Battery (NP-40)
Rated Voltage .................... 3.7 V
Rated Capacitance ............ 1230 mAh
Operating Temperature
Range .................................. 0°C to 40°C (32°F to 104°F)
Dimensions ........................ 38.5(W) x 38.0(H) x 9.3(D) mm
(1.5˝(W) x 1.5˝(H) x 0.37˝(D))
Weight ................................. Approximately 34 g (1.20 oz)
Special battery charger unit (BC-30L) : Inlet Type
Power Requirement .......... 100 to 240V AC, 0.13A, 50/60Hz
Output ................................. DC 4.2V, 900 mA
Charging Temperature ..... 5°C to 35°C (41°F to 95°F)
Chargeable Battery type ... Rechargeable lithium ion battery (NP-40)
Full Charge Times ............. Approximately 2 hours
Dimensions ........................ 80 (W) x 55 (H) x 30 (D) mm
(3.1˝(W) x 2.2˝(H) x 1.2˝(D))
(excluding projections)
Weight ................................. Approximately 60 g (2.1 oz)
APPENDIX
247
Special battery charger unit (BC-30L) : Plug-in Type
Power Requirement .......... 100 to 240V AC, 0.13A, 50/60Hz
Output ................................. DC 4.2V, 900 mA
Charging Temperature ..... 5°C to 35°C (41°F to 95°F)
Chargeable Battery type ... Rechargeable lithium ion battery (NP-40)
Full Charge Times ............. Approximately 2 hours
Dimensions ........................ 80 (W) x 55 (H) x 25 (D) mm
(3.1˝(W) x 2.2˝(H) x 0.98˝(D))
(excluding projections)
Weight ................................. Approximately 63 g (2.2 oz)
Power Supply
Use only the special NP-40 rechargeable lithium ion battery to power this
camera. Use of any other type of battery is not supported.
This camera does not have a separate battery for the clock. The date and
time settings of the camera are cleared whenever power is totally cut off
(from both the battery and AC adaptor). Be sure to reconfigure these
settings after power is interrupted (page 51).
LCD Panel
The LCD panel is a product of the latest LCD manufacturing technology that
provides a pixel yield of 99.99%. This means that less than 0.01% of the
total pixels are defective (they do not turn on or always remain turned on).
Lens
You may sometimes notice some distortion in certain types of images, such
as a slight bend in lines that should be straight. This is due to the
characteristics of lens, and does not indicate malfunction of the camera.
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Casio EX-P600 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Casio EX-P600 in de taal/talen: Engels als bijlage per email.

De handleiding is 6,22 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Casio EX-P600

Casio EX-P600 Gebruiksaanwijzing - Nederlands - 247 pagina's

Casio EX-P600 Gebruiksaanwijzing - Deutsch - 247 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info