Handleiding Casio CTK-2000 (pagina 44 van 46) (Engels)

466806

Verklein

Vergroot

Pagina terug

1/46

Pagina verder

GUÍA DEL USUARIO

USER’S GUIDE

CTK2000/3000ES1B

Guarde toda información para tener como referencia futura.

Please keep all information for future reference.

Precauciones de seguridad

Antes de intentar usar el teclado, asegúrese de leer

las “Precauciones de seguridad” separadas.

Safety Precautions

Before trying to use the keyboard, be sure to read the

separate “Safety Precautions”.

EnglishEspañol

Important!

Please note the following important information before using this product.

• Before using the optional AD-5 Adaptor to power the unit, be sure to check the AC Adaptor for any damage first. Carefully check

the power cord for breakage, cuts, exposed wire and other serious damage. Never let children use an AC adaptor that is

seriously damaged.

• Never attempt to recharge batteries.

• Do not use rechargeable batteries.

• Never mix old batteries with new ones.

• Use recommended batteries or equivalent types.

• Always make sure that positive (+) and negative (–) poles are facing correctly as indicated near the battery compartment.

• Replace batteries as soon as possible after any sign they are getting weak.

• Do not short-circuit the battery terminals.

• The product is not intended for children under 3 years.

• Use only CASIO AD-5 adaptor.

• The AC adaptor is not a toy.

• Be sure to disconnect the AC adaptor before cleaning the product.

NOTICE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC WARNING

Changes or modifications not expressly approved by the party responsible for compliance could void the userís authority to

operate the equipment.

Declaration of Conformity

Model Number: CTK-2000/CTK-3000

Trade Name: CASIO COMPUTER CO., LTD.

Responsible party: CASIO AMERICA, INC.

Address: 570 MT. PLEASANT AVENUE, DOVER, NEW JERSEY 07801

Telephone number: 973-361-5400

This device complies with Part 15 of the FCC Rules, Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

This mark applies in EU countries only.

Manufacturer:

CASIO COMPUTER CO.,LTD.

6-2, Hon-machi 1-chome, Shibuya-ku, Tokyo 151-8543, Japan

Responsible within the European Union:

CASIO EUROPE GmbH

Bornbarch 10, 22848 Norderstedt, Germany

● Company and product names used in this manual may be registered trademarks of others.

● Any reproduction of the contents of this manual, either in part or its entirety, is prohibited. Except for your own,

personal use, any other use of the contents of this manual without the consent of CASIO is prohibited under

● IN NO EVENT SHALL CASIO BE LIABLE FOR ANY DAMAGES WHATSOEVER (INCLUDING, WITHOUT

LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, LOSS OF

INFORMATION) ARISING OUT OF THE USE OF OR INABILITY TO USE THIS MANUAL OR PRODUCT,

EVEN IF CASIO HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

● The contents of this manual are subject to change without notice.

English

E-1

Contents

General Guide ............................. E-2

Using the 10-key Pad (

) ..................................... E-4

Using the Setting Button (

)................................. E-4

Getting Ready to Play ................ E-5

Preparing the Music Stand ..................................... E-5

Power Supply ......................................................... E-5

Playing the Digital Keyboard..... E-6

Turning on Power and Playing ............................... E-6

Using Headphones................................................. E-6

Changing Keyboard Response to

Touch Pressure (Touch Response)

(CTK-3000 only) ..................................................... E-7

Using the Metronome ............................................. E-8

Controlling the

Keyboard Sounds....................... E-9

Select from a variety of musical

instrument sounds .................................................. E-9

Using Reverb........................................................ E-10

Using a Pedal ....................................................... E-10

Changing the Pitch

(Transpose, Tuning) ............................................. E-11

Using the Pitch Bend Wheel to

Shift the Pitch of Notes (CTK-3000 Only)............. E-11

Sampling a Sound and Playing It

on the Keyboard (Sampling)................................. E-12

Using a Sampled Sound in a Rhythm

(Drum Assign)....................................................... E-14

Playing Built-in Songs ............. E-15

Playing the Demo Songs...................................... E-15

Playing Back a Particular Song ............................ E-15

Using Built-in Songs to

Master Keyboard Play .............. E-19

Phrases ................................................................ E-19

Step Up Lesson Flow ........................................... E-19

Selecting the Song, Phrase, and

Part You Want to Practice .................................... E-20

Lessons 1, 2, and 3 .............................................. E-21

Lesson Settings .................................................... E-22

Using Auto Step Up Lesson ................................. E-23

Music Challenge

Keyboard Game ........................ E-25

Using Auto Accompaniment.... E-27

Playing the Rhythm Part Only .............................. E-27

Playing All Parts ................................................... E-28

Using Auto Accompaniment Effectively................ E-30

Using One-Touch Preset ...................................... E-31

Connecting External Devices

..... E-32

Connecting a Computer........................................ E-32

MIDI Settings ........................................................ E-33

Connecting to Audio Equipment........................... E-35

Reference................................... E-36

Troubleshooting.................................................... E-36

Specifications ....................................................... E-38

Operating Precautions.......................................... E-39

Song List............................................................... E-40

Chord Chart .......................................................... E-41

MIDI Implementation Chart

Included Accessories

● Music Stand

● Song Book

● Leaflets

• Safety Precautions

• Appendix

• Other (Warranty, etc.)

Items included as accessories are subject to change without notice.

Separately Available Accessories

• You can get information about accessories that

are separately for this product from the CASIO

keyboard catalog available from your retailer, and

from the CASIO website at the following URL.

http://world.casio.com/

E-2

General Guide

• In this manual, the term “Digital Keyboard” refers to the CTK-2000/CTK-3000.

• Illustrations in this User’s Guide show the CTK-3000.

• In this manual, buttons and other controllers are identified using the numbers shown below.

789 bmbk bl6

bo bp bq br bs bt ck cl cm

2345

cn co cp cq cr cn

ct dkcs

English

General Guide

E-3

POWER switch ☞E-6

VOLUME slider ☞E-6

SETTING button ☞E-4

SAMPLING button ☞E-12

METRONOME button ☞E-8

INTRO, REPEAT button ☞E-16, 17, 22, 30

NORMAL/FILL-IN, REW button ☞E-16, 20, 27, 30

VARIATION/FILL-IN, FF button ☞E-16, 20, 30

SYNCHRO/ENDING, PAUSE button

☞E-16, 30, 31

START/STOP, PLAY/STOP button

☞E-15, 16, 18, 21, 22, 27

ACCOMP ON/OFF, PART SELECT button

☞E-15, 18, 20, 22, 28, 34

TEMPO buttons ☞E-8, 17, 31

Number buttons, [–]

[+] buttons ☞E-4

SONG BANK button ☞E-15, 17, 20

RHYTHM, ONE TOUCH PRESET button

☞E-9, 27, 31

TONE button ☞E-6, 9

LISTEN button ☞E-21

WATCH button ☞E-21

REMEMBER button ☞E-22

NEXT button ☞E-20

AUTO button ☞E-23

MUSIC CHALLENGE button ☞E-25

Speakers

Song Bank list

Rhythm list

Display

Tone list

PITCH BEND wheel (CTK-3000 only) ☞E-11

CHORD root names ☞E-28

Percussion instrument list ☞E-9

dm dn do dp

USB port ☞E-32

SUSTAIN jack ☞E-10

PHONES/OUTPUT jack ☞E-6, 35

AUDIO IN jack ☞E-12, 35

DC 9V terminal ☞E-5

General Guide

E-4

Use the number buttons and the [–] and [+] buttons to change

the settings of the parameters that appear in the upper left

area of the display.

Use the number buttons to enter numbers and values.

• Enter the same number of digits as the currently displayed

value.

Example: To enter tone number 005, input 0 3 0 3 5.

• Negative values cannot be input using the number buttons.

Use [+] (increase) and [–] (decrease) instead.

You can use the [+] (increase) and [–] (decrease) buttons to

change the displayed number or value.

• Holding down either button scrolls the displayed setting.

• Pressing both buttons at the same time will revert to the

initial default setting or the recommended setting.

Use the Setting button (

) to access settings that let you

select the reverb type, pedal effect, etc.

Press

Next press

until the parameter whose setting

you want to change is displayed.

Each press of

cycles through the available parameters.

When the parameter you want is displayed, use

(10-key) to change its setting.

• The parameter setting will disappear from the upper left

area of the screen if you do not perform any operation

for some time.

• The tone and other parameters revert to their initial

defaults whenever you turn on power (page E-6).

Using the 10-key Pad (

)

Number Buttons

[–] and [+] Buttons

Mde r nPno

Setting

Using the Setting Button (

)

Parameter Display See Page

1 Transpose Trans. E-11

2 Accompaniment Volume AcompVol E-31

3 Song Volume Song Vol E-17

Touch Response

(CTK-3000 only)

Touch E-7

5 Tuning Tune E-11

6 Reverb Reverb E-10

7 Voice Fingering Guide Speak E-22

8 Note Guide NoteGuid E-23

9 Performance Evaluation Scoring E-23

10 Phrase PhraseLn E-23

11 Sampling Start SmplAuto E-13

12 Keyboard Channel Keybd Ch E-33

13 Navigate Channels Navi. Ch E-33

14 Local Control Local E-34

15 Accomp Out AcompOut E-34

16 Pedal Effect Jack E-10

Pitch Bend Range

(CTK-3000 only)

Bend Rng E-11

T r a n s .

Parameter

Setting

English

E-5

Getting Ready to Play

Either an AC adaptor or batteries can be used to power this

Digital Keyboard. Normally, use of AC adaptor power is

recommended.

• The AD-5 AC adaptor does not come with this Digital

Keyboard. Purchase it separately from your retailer. See

page E-1 for information about options.

Use the AD-5 AC adaptor when you want to power the Digital

Keyboard from a household electrical outlet.

• Be sure to turn off Digital Keyboard power before

connecting or disconnecting the AC adaptor.

• Be sure to turn off power before loading batteries.

• It is up to you to prepare six commercially available

AA-size batteries. Do not use oxyride batteries or any

other nickel based batteries.

Open the battery cover on the bottom of the

Digital Keyboard.

Load six AA-size batteries into the battery

compartment.

Make sure the positive + and negative - ends of the

batteries are facing as shown in the illustration.

Insert the tabs of the battery cover into the

holes on the side of the battery compartment,

and close the cover.

■ Low Battery Indication

The indicator shown below starts to flash to let you know

when battery power is low. Replace the batteries with new

ones.

Preparing the Music Stand

Power Supply

Using the AC Adaptor

Music stand

Household power outlet

AD-5DC 9V terminal

Using Batteries

Tabs

Low battery indicator

(flashes)

E-6

Playing the Digital Keyboard

Turn on

This turns on power.

Try playing something on the keyboard. Use

to adjust volume.

• Turning off the keyboard power causes all current

settings and sampled sounds (page E-12) to be cleared.

The keyboard will revert to initial default settings the

next time you turn it on.

While you are using batteries for power, power will turn off

automatically if you do not perform any operation for about six

minutes. Auto Power Off is disabled while the AC adaptor is

being used for power.

■ Disabling Auto Power Off

You can disable Auto Power Off to ensure that power is not

turned off automatically during a concert, etc.

While holding down

, turn on power.

Auto Power Off will be disabled.

Using headphones cuts off output from the built-in speakers,

which means you can practice playing even late at night

without disturbing others.

• Be sure to turn down the volume level before connecting

headphones.

• Headphones do not come with the Digital Keyboard.

• Use commercially available headphones. See page E-1 for

information about options.

• Do not listen to very high volume output over

headphones for long period. Doing so creates the risk

of hearing damage.

• If you are using headphones that require an adaptor

plug, make sure you do not leave the adaptor plugged

in when removing the headphones.

bqbqbkbk

11 22 33 55

bnbn

bmbm

Turning on Power and Playing

Auto Power Off (Using Batteries)

Increase

Decrease

Using Headphones

PHONES/OUTPUT jack

English

Playing the Digital Keyboard

E-7

Touch Response alters tone volume in accordance with

keyboard pressure (speed). This provides you some of the

same expressivity you get on an acoustic piano.

■ Sound intensity depends on the speed that keys

are pressed.

People normally believe that the stronger the pressure applied

to a piano keyboard, the louder the sound. Actually, however,

the intensity of the notes played depends on the speed at

which keys are pressed. Notes are louder when keys are

pressed quickly, and quieter when keys are pressed slowly.

Keeping this in mind as you play a keyboard musical

instrument lets you control note volume without striving to

apply too much pressure with your fingertips.

■ The playability of an acoustic piano

Your Digital Keyboard provides you with key touch that is the

next best thing to an acoustic piano. Note volume changes

automatically in accordance with key press speed.

Use the procedure below to control how much the volume of

played notes change in accordance with playing speed.

Select the setting that best matches your playing style.

Press

a number of times until “Touch”

appears on the display (page E-4).

Use

(10-key) [–] and [+] keys to select one of

the three Touch Response sensitivity settings.

Changing Keyboard Response to

Touch Pressure

(Touch Response)

(CTK-3000 only

)

Keyboard Instrument Sound Intensity

Pressing fast produces

louder notes.

Pressing slowly produces

softer notes.

Do not try to use too much

pressure.

Changing Touch Response Sensitivity

Off (oFF) Touch Response is turned off. Sound

volume is fixed, regardless of key press

speed.

Type 1 (1) Normal Touch Response

Type 2 (2) More sensitive Touch Response than Type 1

T o u c h

Indicator disappears when

Touch Response is turned off.

Playing the Digital Keyboard

E-8

The metronome lets you play and practice along with a steady

beat to help keep you on tempo.

Press

This starts the metronome.

Press

again to stop the metronome.

You can configure the metronome to use a bell sound for the

first beat of each measure of the song you are playing.

• You can specify 0, or a value from 2 to 6 as the number of

beat per measure.

• When playing a built-in song, the beats per measure setting

(which determines when the bell sounds) is configured

automatically for the currently selected song.

Hold down

until the beats per measure

setting screen appears on the display.

• If you do not perform any operation for after the beats

per measure setting screen appears, the display will

return to the screen displayed before you pressed

Use

(10-key) to enter the number of beats

per measure.

• The bell will not sound if you specify 0 for this setting. In

this case, all beats are indicated by a click sound. This

setting lets you practice with a steady beat, without

worrying how many beats there are in each measure.

Use the following procedure to change the tempo of the

metronome.

Press

Use y (slower) and t (faster) to change the tempo

setting. Holding down either button changes the setting at

high speed.

• Pressing y and t at the same time will initialize the

tempo setting in accordance with the currently selected

song or rhythm.

• Pressing

causes the tempo value to flash on the

display. While the tempo value is flashing, you can use

(10-key) to change it.

Note that you must input leading zeros, so 89 is input

as 089.

• The tempo value will stop flashing if you do not perform

any operation for a short while.

The metronome volume setting is changed automatically with

the volume level of the currently selected Auto

Accompaniment or song. The metronome volume cannot be

adjusted independently.

• For information about changing the Auto Accompaniment

volume, see page E-31.

• For information about changing the song volume, see page

E-17.

• You cannot adjust the balance between the metronome

and note volume during Auto Accompaniment and built-in

tune play.

Using the Metronome

Start/Stop

Changing the Beats Per Measure

This pattern changes with each beat.

Bea t

Changing the Metronome Tempo

Changing the Metronome Sound Volume

Tempo value (flashes)

English

E-9

Controlling the Keyboard Sounds

Your Digital Keyboard lets you select tones for a wide variety

of musical instrument sounds, including violin, flute, orchestra,

and more. Even the same song sound takes on a different feel

by changing the instrument type.

Press

Use

(10-key) to select the tone number you

want.

The corresponding tone number and tone name will

appear on the screen.

• See the separate “Appendix” for a complete list of available

tones.

• You also can find out instrument numbers using the tone

groups printed on the Digital Keyboard’s console.

• Use the number buttons to enter the tone number. Specify

three digits for the tone number.

Example: To select 001, enter 0 3 0 3 1.

• When one of the drum sets is selected (tone numbers 395

through 400), each keyboard key is assigned a different

percussion sound.

Try playing something on the keyboard.

The tone of the instrument you selected will sound.

Press

and

at the same time.

This selects the grand piano tone.

Settings

bqbq

11 33

bnbn

bpbp

cscs

Select from a variety of musical

instrument sounds

To select an instrument for playing

S t . G r P n o

Tone name

Tone number

Playing with a Piano Tone (Piano Setup)

Tone Number: “001”

Reverb: “06”

Transpose: 00

Touch Response: Off: Returns to initial default

On: No change

Pedal Effect: SUS

Rhythm Number: “131”

Accompaniment: Rhythm part only

Local Control: On

Drum Assign: Off

Controlling the Keyboard Sounds

E-10

Reverb adds reverberation to notes. You can change the

duration of the reverb.

Press

a number of times until “Reverb”

appears on the display (page E-4).

Use the

(10-key) [–] and [+] keys to select the

reverb setting you want.

A pedal can be used to change notes in various ways while

playing.

• A pedal unit does not come with the Digital Keyboard.

Purchase one separately from your retailer. See page E-1

for information about options.

Connect an optional pedal unit.

Press

a number of times until “Jack”

appears on the display (page E-4).

Use the

(10-key) [–] and [+] keys to select the

pedal effect you want.

• The following shows the available pedal effects.

Using Reverb

Off (oFF) Turns off reverb.

1 to 10 The larger the number selected, the longer

the reverb duration.

Reverb

R e v e r b

Indicator disappears when reverb is turned off.

Using a Pedal

Connecting a Pedal Unit

Selecting the Pedal Effect

Sustain

(SUS)

Sustains notes played while the pedal is

depressed. Organ and other similar tone

notes are sustained even if the pedal is not

pressed.

Sostenuto

(SoS)

Sustains notes that are playing when the

pedal is depressed before the keyboard

keys are released.

Soft

(SFt)

Slightly softens notes played while the pedal

is depressed.

Rhythm

(rHy)

Pressing the pedal starts and stops Auto

Accompaniment or song playback.

SUSTAIN jack

J a c k

English

Controlling the Keyboard Sounds

E-11

The transpose feature lets you change the pitch, in semitone

steps. A simple operation lets you instantly change the pitch

to match that of a singer.

• The transpose setting range is –12 to +12 semitones.

Press

Use the

(10-key) [–] and [+] keys to select the

transpose setting you want.

Use the tuning feature when you need to adjust the pitch

slightly to play along with another musical instrument. Also,

some artists perform their music with slightly altered tuning.

You can use the tuning feature to adjust tuning so it exactly

matches a performance on a CD.

• The tuning setting range is –99 to +99 cents.

Press

a number of times until “Tune”

appears on the display (page E-4).

Use the

(10-key) [–] and [+] keys to adjust the

tuning.

You can use the pitch bend wheel to slide the pitch of notes

smoothly upwards and downwards. This technique makes it

possible to produce effects that are similar to sounds

produced when bending notes on a saxophone or electric

guitar.

While playing a note on the keyboard, rotate the

pitch bend wheel on the left of the keyboard

upwards or downwards.

The amount the note bends depends on how much you

rotate the pitch bend wheel.

• Do not have the pitch bend wheel rotated as you turn

on the keyboard.

Use the following procedure to specify how much the pitch of

the note changes whenever the pitch bend wheel is rotated

upwards or downwards. You can specify a range from 0 to 12

semitones (one octave).

Press

a number of times until “Bend Rng”

appears on the display (page E-4).

Use the

(10-key) [–] and [+] keys to change

the range.

Changing the Pitch

(Transpose, Tuning)

Changing the Pitch in Semitone Steps

(Transpose)

Fine Tuning (Tuning)

Trans.

Tune

Using the Pitch Bend Wheel to

Shift the Pitch of Notes

(CTK-3000 Only

)

To play with the pitch bend wheel

Specifying the Pitch Bend Range

B e n d R n

Controlling the Keyboard Sounds

E-12

You can use the Digital Keyboard to sample a sound from a

portable audio player, or other device, and then play the

sound with keyboard keys. For example, you could sample

the bark of your dog and then use the sound in a melody. You

also can sample and use passages from a CD. The sampling

feature is a great way to create new sounds that are highly

creative.

Connect a external device.

• Connection requires commercially available connecting

cords, supplied by you. The connecting cords should have

a stereo mini plug on one end and a plug that matches the

configuration of the external device on the other end.

• Turn off the external device and the Digital Keyboard

before connecting them.

• Sampled sounds are recorded in monaural.

Turn the volume levels of the external device

and Digital Keyboard down.

Turn on the external device and then the Digital

Keyboard.

Press

This enters record standby.

Output the sound from the external device.

The Digital Keyboard will start sampling automatically,

and stop after one second.

What you sample is stored as tone number 401.

Try playing something on the keyboard.

• Sampling will not start if the volume level of the external

device is too low.

• A new sample replaces sample data currently stored as

tone number 401. The old data is deleted.

Sampling a Sound and Playing It

on the Keyboard (Sampling)

Connection

Keyboard AUDIO IN jack

CD player, Cassette player,

etc.

Stereo mini plug

Sampling a Sound and Playing It

a i t i n

Flashes

S a m

l i n

O r i

i n a l

Flashes

Lights

English

Controlling the Keyboard Sounds

E-13

Turning off power will cause any sampled sound data on the

keyboard to be deleted.

■ How sampled sounds are played

Pressing Middle C (C4) will play back the original sound. The

keys to the left and right of C4 play the sound at different

pitches.

Press

a number of times until “SmplAuto”

appears on the display (page E-4).

Press

(10-key) [–] key to select the OFF

setting.

This enables manual sampling. When this setting is

selected, sampling will not start until you press

• When the above setting is “oFF”, sampling starts when

you release

, not when you press it. Sampling will not

start if you keep

depressed.

You can apply various effects to the sample sound stored at

tone number 401.

Use

(10-key) to select a tone number from

402 to 411.

Tone numbers 402 to 411 actually represent effects

assigned to tone number 401. Selecting a tone will play

the sampled sound in a loop, along with the applicable

effect, as described below.

Turning off power clears sampled data!

Starting a Sampling Operation Manually

S m

l A u t o

Applying Effects to a Sampled Sound

Effect

Name

Description

402 Loop 1 Loops the sampled sound.

403 Loop 2

Loops the sample sound and raises the

pitch of the resonating sound when the

keyboard key is released.

404 Loop 3

Loops the sample sound and lowers the

pitch of the resonating sound when the

keyboard key is released.

405 Pitch 1

Changes the pitch from low to high, at an

increasing rate.

406 Pitch 2

Changes pitch from high to low, at a

decreasing rate.

407 Pitch 3

Changes pitch from high to low, at a

decreasing rate, and then raises the pitch

when the key is released.

408 Tremolo Alternates volume between high and low.

409 Funny 1

Adds vibrato and changes pitch by a

gradually increasing amount.

410 Funny 2

Alternates between high pitch and low

pitch.

411 Funny 3

Adds vibrato and changes pitch from low

to high.

Controlling the Keyboard Sounds

E-14

Use the following procedure to replace a percussive

instrument with a sound you sampled and play auto

accompaniment rhythms (page E-27) with the sampled

sound.

Press

and

at the same time.

The display will return to the previous screen if you do not

perform the next step for some time.

Use the

(10-key) [–] and [+] keys to select the

drum assign type you want.

Start rhythm play (page E-27).

The rhythm sounds in accordance with the drum assign

type you selected in step 2.

• If the rhythm does not include a bass drum and snare drum,

the sampled sound will not sound while Type 1 is selected.

• Rhythm numbers 140, and 142 to 150 do not use

percussive instruments, so the sampled sound does not

sound when these rhythm numbers are selected.

Using a Sampled Sound in a

Rhythm (Drum Assign)

Off (oFF) Sampled sound does not sound.

Type 1 (dr1) Replaces the bass drum and snare drum of

the rhythm with the sampled sound.

Type 2 (dr2) Replaces more of the percussive

instruments than Type 1 with the sampled

sound.

D r m A s i

Lights

English

E-15

Playing Built-in Songs

With this Digital Keyboard, built-in tune data is referred to as

“songs”. You can listen to the built-in songs for your own

enjoyment, or you can play along with them for practice.

• In addition to simple listening enjoyment, the built-in songs

can be used with the lesson system (page E-19) for

practice.

Use the following procedure to play back built-in songs (001 to

090).

Press

and

at the same time.

This will start playback of the demo songs. Demo

playback continues until you stop it.

• See page E-40 for a complete list of available songs.

• Demo playback always starts from song number 001.

To change to another song while demo

playback is in progress, use

(10-key) [–] and

[+] keys to enter the song number you want

(page E-4).

This will cause demo playback to jump to the song whose

number you entered.

• You cannot use

(10-key) number buttons to select a

song.

To stop demo playback, press

Demo playback continues until you stop it by pressing

Use the procedure below to play back one of the built-in

songs. You can play along on the keyboard with song

playback.

Press

Use

(10-key) to enter the number of the song

you want.

• See page E-40 for a complete list of available songs.

• Song group names are printed on the Digital

Keyboard’s console.

bkbk

bnbn

bmbm887766 99 blbl bobo

Playing the Demo Songs

T w i n k l e

Tune name

Song numberFlashes

Playing Back a Particular Song

Start/Stop

T w i n k l e

Tune name

Song numberLights Lights

Playing Built-in Songs

E-16

Press

This starts playback of the song.

Press

again to stop playback.

Song playback will continue (repeat) until you press

stop it. You can cancel song repeat by pressing

(“REPEAT” indicator disappears from the display).

Use the operations in this section to perform pause, skip

forward, and skip back operations.

■ Pause

Press

This pauses song playback.

Press

again to resume playback from the

point where you paused it.

■ Skip Forward

Press

This skips song playback forward to the next measure.

Each press of

skips ahead one measure. Holding

down

skips forward at high speed until you release it.

• Pressing

while song playback is stopped performs

lesson function phrase skip forward (page E-20).

■ Skip Back

Press

This skips song playback back to the previous measure.

Each press of

skips back one measure. Holding down

skips back at high speed until you release it.

• Pressing

while song playback is stopped performs

lesson function phrase skip back (page E-20).

You can use the procedure in this section to repeat particular

measures for practice playing along until you master it. You

can specify the start measure and the end measure of the

section you want to play and practice.

Press

to temporarily turn off song repeat

(“REPEAT” disappears from the display).

When song playback reaches the measure you

want to specify as the start measure, press

This specifies the measure as the start measure.

Pause, Skip Forward, Skip Back

M o o n l i

Key Note

Tempo

BeatMeasure

Fingering

Sustain pedal

Repeating Playback of Specific Measures

Measure number

Start End

These measures are repeated.

T w i n k l e

Flashes

English

Playing Built-in Songs

E-17

When playback reaches the measure you want

to select as the end measure, press

again.

This specifies the measure as the end measure and starts

repeat playback of the measures in the specified range.

• During repeat play you can use

to pause playback,

to skip forward, or

to skip back.

Pressing

again returns to normal playback.

Changing the song number clears the start measure and

end measure of the repeat operation.

You can use the following procedure to change the speed

(tempo) in order to slow down playback to practice difficult

passages, etc.

Press

Use y (slower) and t (faster) to change the tempo

setting. Holding down either button changes the setting at

high speed.

•Pressing y and t at the same time will return the

current song to its original default tempo.

•Pressing

causes the tempo value to flash on the

display. While the tempo value is flashing, you can use

(10-key) to change it. The tempo value will stop

flashing if you do not perform any operation for a short

while.

• Changing the song number will return the song to its

original default tempo.

Use the following procedure to adjust the balance between

the volume of what you play on the keyboard and song

playback volume.

Press

a number of times until “Song Vol”

appears on the display (page E-4).

Use the

(10-key) [–] and [+] keys to adjust the

song volume.

The procedure below lets you select the same keyboard tone

as the one being used in the song and play along with your

favorite tunes.

After selecting a song, hold down

for about

two seconds until the displayed tone name

changes to the tone name of the song.

• If your currently selected tone is the same as the song

tone, the display contents will not change.

Play along with song playback.

• If you select a song that uses different tones for left and

right hand play, the right hand part tone is assigned to the

keyboard.

Changing Playback Speed (Tempo)

T w i n k l e

Lights

T w i n k l e

Adjusting the Song Volume

Playing with the Tone as Song Playback

S o n

V o l

Playing Built-in Songs

E-18

You can turn off the right hand part or the left hand part of a

song during playback and practice playing the along with the

remaining part.

Press

to select the part you want to turn off.

Each press of

cycles through the settings shown

below.

Press

This starts playback in accordance with the setting you

selected in step 1.

• During playback with one part turned off, only the notes of

the part that is turned off are shown on the display.

Turning Off the Part of One Hand for Practice

(Part Select)

Right hand part off

Left hand part off

Both hand parts off

Both hand parts on

English

E-19

Using Built-in Songs to Master Keyboard Play

To master a song, it is best to break it up into shorter parts

(phrases), master the phrases, and then put everything

together. Your Digital Keyboard comes with a Step Up Lesson

feature that helps you to do just that.

The built-in songs are pre-divided into phrases to help you

master keyboard play.

Step Up Lesson takes you through practice of the right hand

part, left hand part, and both hand parts for each phrase of a

song. Master all of the phrases and you master the song.

bkbk

bnbn

887766 blbl

btbt

bsbs

brbr

ckck

clcl

bobo

Phrases

Song start Song end

Phrase 1 Phrase 2 Phrase 3 . . . .

Final

Phrase

Step Up Lesson Flow

Phrase 1

• Right Hand Lesson 1, 2, 3

• Left Hand Lesson 1, 2, 3

• Both Hand Lesson 1, 2, 3

Repeat the above to practice phrase

2, 3, 4, and so on, until you reach the

final phrase of the song.

After mastering all of the phrases,

practice the entire song.

Now you have mastered the entire

song!

Using Built-in Songs to Master Keyboard Play

E-20

The following are the messages that appear on the display

during Step Lessons.

First, select the song, phrase, and part you want to practice.

Select the song you want to practice (page

E-15).

This will select the first phrase of the song.

Press

(or

) to move forward one phrase, or

to move back one phrase.

• Holding down

scrolls through phrases at high

speed.

• The keyboard remembers the last phrase you practiced

for up to 20 songs. To recall the last practice phrase for

the current song (if it is available), hold down

Press

to select the part you want to practice.

Each press of

cycles through the settings

shown below.

Hold down

for about two seconds.

The same tone used for song playback will be assigned to

the keyboard (page E-17).

Messages that Appear during Lessons

Message Description

<Phrase> Appears when you select a phrase, when a

lesson starts, etc.

• Note that certain phrases will cause “Wait”

to appear instead of “Phrase”.

<Wait> Appears when the lesson starts with an intro

or fill-in phrase that is not included in the

phrases to be practiced. Play toll advance

automatically to the next phrase after the un-

included phrase plays, so wait until then to

start playing on the keyboard.

NextPhrs Appears when advancing automatically to the

next phrase. This message appears following

a phrase for which “Wait” (see above) is

displayed, and during an Auto Step Up Lesson

(page E-23).

From Top This message appears during Auto Step Up

Lesson (page E-23) immediately before

practice from Phrase 1 up until the phrase

currently being practiced.

Complete Appears at the end of Auto Step Up Lesson

(page E-23).

Selecting the Song, Phrase, and

Part You Want to Practice

P h r a s e

Phrase number

First measure of the selected phrase

Right hand practice

Left hand practice

Both hand practice

* This indicator (setting) is skipped if you press

while a

lesson is in progress.

English

Using Built-in Songs to Master Keyboard Play

E-21

Now it is time to start the lessons. First, select the song and

part you want to practice.

First, listen to the example a few times to familiarize yourself

with what it sounds like.

Press

This starts example play.

To stop Lesson 1, press

Play the song on the keyboard. During this lesson, the display

shows the key you need to press next. Voice fingering guide

also uses a simulate voice to announce which finger you

should use. Follow the instructions to press the correct

keyboard keys and play the notes. Don’t worry if you play the

wrong note. Song playback will wait until you play the correct

note. Take your time and play at your own pace.

Press

This starts Lesson 2.

Play notes on the keyboard in accordance with

the instructions provided on the display and by

voice fingering guide.

During this lesson, the display shows the key you need to

press next. Voice fingering guide uses a simulate voice to

announce which finger you should use.

To stop Lesson 2, press

● If you complete Lesson 2 play to the end, a score that

rates your play appears on the screen.

Lessons 1, 2, and 3

Lesson 1: Listen to the song.

Lesson 2: Watch how the song is played.

P h r a s e

Lights

P h r a s e

Lights

Master playing the correct note with the correct finger

as instructed by the guidance. Practice playing with the

correct timing.

Song playback will wait for you to play the correct note.

• Keyboard key goes from flashing to lit.

• Note guide sounds the correct note to be played.

• Voice Fingering Guide tells you what finger to use.

Pressing the correct keyboard key causes song

playback to resume and the key for the next note

flashes.

Bravo! You pass! Advance to the next lesson.

Again! Go back and try again.

Flashes

Lights

Using Built-in Songs to Master Keyboard Play

E-22

Though song playback stands by waiting for you to press the

correct keys as in Lesson 2, the Digital Keyboard does not

provide any guidance about what note you need to play next.

Remember everything you have learned up to Lesson 2 as

you play.

Press

This starts Lesson 3.

Play the song along with the song playback.

To stop Lesson 3, press

• If you complete Lesson 3 play to the end, a score that

rates your play appears on the screen the same as with

Lesson 2.

After you successfully complete all of the phrases in Lessons

1, 2, and 3, it is time to try playing the entire song from

beginning to end.

Use

to turn off both hand parts and then

press

Try playing with both hands and find out how the Digital

Keyboard evaluates your effort.

You can turn off phrase repeat for Lessons 1, 2, and 3.

Press

This disables phrase repeat play.

Use the following procedure to turn off voice fingering guide,

which tells you which finger to use to play each note in

Lesson 2 and Lesson 3.

Press

a number of times until “Speak”

appears on the display (page E-4).

Press the

(10-key) [–] key to select the OFF

setting.

Lesson 3: Remember what you learned as

you play.

Press the keyboard keys you learned in Lesson 2.

Song playback will wait for you to play the correct note.

• Note guide sounds the correct note to be played.

If you are still unable to press the correct keyboard

key, the Digital Keyboard will display keyboard

guidance and voice fingering guide will tell you what

finger to use, just as in Lesson 2.

Pressing the correct key will cause song playback to

resume.

P h r a s e

Lights

Playing a Particular Song All the Way

Through

Lesson Settings

Playing without Phrase Repeat

Turning Off Voice Fingering Guide

T w i n k l e

Disappears

e a k

Indicator disappears

when voice fingering

guide is turned off.

English

Using Built-in Songs to Master Keyboard Play

E-23

Use the following procedure to turn off note guide, which

sounds the note to be played next in Lesson 2 and Lesson 3.

Press

a number of times until “NoteGuid”

appears on the display (page E-4).

Press the

(10-key) [–] key to select the OFF

setting.

Use the following procedure to turn off performance

evaluation, which evaluates your performance and displays a

score in Lesson 2 and Lesson 3.

Press

a number of times until “Scoring”

appears on the display (page E-4).

Press the

(10-key) [–] key to select the OFF

setting.

When the phrase function is turned off, lessons go through an

entire song from beginning to end, without dividing it up

between phrases.

Press

a number of times until “PhraseLn”

appears on the display (page E-4).

Press the

(10-key) [–] key to select the OFF

setting.

With Auto Step Up Lesson, the Digital Keyboard advances

through each lesson automatically.

Select the song and part you want to practice

(page E-15).

Press

Listen to the first phrase in Lesson 1.

• In Lesson 1, the sample phrase is played only once

before advancing to Lesson 2.

Auto Step Up Lesson stops automatically after

you are able to get through all of the lessons

successfully.

• In Lesson 2 and Lesson 3, the Digital Keyboard

advances to the next lesson if you are able to achieve

the “Bravo!” evaluation result.

• To cancel a lesson, press

• You can change the step and phrase during Auto Step Up

Lesson using

, and

• Starting Auto Step Up Lesson automatically turns on

phrase repeat (page E-22) and play evaluation (page

E-23). These features cannot be turned off during lessons.

Turning Off Note Guide

Turning Off Performance Evaluation

Lesson Play without Dividing Songs into

Phrases

N o t e G u i d

S c o r i n

Indicator disappears

when performance

evaluation is turned off.

P h r a s e L n

Using Auto Step Up Lesson

Lights

Flashes

Using Built-in Songs to Master Keyboard Play

E-24

■ Auto Step Up Lesson Procedure

* Auto Step Up Lesson advances to the next phrase,

regardless of whether the “Bravo!” result is attained.

Phrase 1

Lesson 1

Lesson 2

Lesson 3

Phrase 2

Lesson 1

Lesson 2

Lesson 3

Phrase 1, 2

• Lesson 3*

Phrase 3

Lesson 1

Lesson 2

Lesson 3

Phrase 1, 2, 3

• Lesson 3*

Next phrase practice using the same

procedure

Final phrase

Lesson 1

Lesson 2

Lesson 3

From Phrase 1 to the final phrase

• Lesson 3*

Lesson complete

English

E-25

Music Challenge Keyboard Game

Music Challenge is a game that measures your reaction

speed as you press keys in response to on-screen keyboard

indicators and fingering guide indications.

Press

This causes a key on the on-screen keyboard to start to

flash, and starts the Music Challenge song.

After the on-screen keyboard indicator changes

from flashing to lit, press the indicated key with

the indicated finger as quickly as possible.

This causes the on-screen keyboard key to go out to let

you know that you cleared the first note. The next on-

screen keyboard key starts to flash, so get ready to press

the next key.

• The time it takes you to press the keyboard key after

the on-screen key lights appears on the display (Unit:

0.1 sec). The shorter the time, the higher your score.

• Pressing a keyboard key before the on-screen key

goes from flashing to lit, will not advance to the next

note.

cmcm

bqbqbkbk bobo bpbp

Displayed during a game.Number of remaining notes

Fingering

M . C H A L . !

Time 0.3sec

Music Challenge Keyboard Game

E-26

The game ends when you advance successfully

through 20 notes.

• Your score and playing time appear on the display.

After a short while, the playing time display changes to

an evaluation result. To clear the evaluation result from

the display, press

, or

• You can cancel a game at any time by pressing

Evaluation Result

• Notes and fingering guide fingers are indicated randomly.

• The tempo of the game songs cannot be changed.

• All buttons except

, and

are disabled while a game

is in progress.

S <High>

B Evaluation Ranges

D <Low>

T i m e 1 9 . 2

G r a d e : A

Score

Playing time

Evaluation result

English

E-27

Using Auto Accompaniment

With Auto Accompaniment, simply select an accompaniment

pattern. Each time you play a chord with your left hand the

appropriate accompaniment will play automatically. It’s like

having a personal backup group along with you wherever you

go.

• Auto Accompaniments are made up of the following three

parts.

(1) Rhythm

(2) Bass

(3) Harmony

You can have only the rhythm part play, or you can have all

three parts play at the same time.

The rhythm part is the foundation each Auto Accompaniment.

Your Digital Keyboard comes with a variety of built-in rhythms,

including 8-beat and waltz. Use the following procedure to

play the basic rhythm part.

Press

Use

(10-key) to select the rhythm number

you want.

• See the separate “Appendix” for information about

individual rhythms.

• You also can find out rhythm numbers using the rhythm

groups printed on the Digital Keyboard’s console.

Press

This starts the rhythm.

Play along with the rhythm.

To stop the rhythm, press

again.

bkbk

bnbn

bmbm887766 99 blbl bpbp

Playing the Rhythm Part Only

Starting and Stopping the Rhythm Part Only

F u n k 8 B t

Rhythm number

Rhythm pattern name

This pattern changes with each beat.

Using Auto Accompaniment

E-28

Playing a chord with your left hand automatically adds bass

and harmony accompaniment parts to the currently selected

rhythm. It is just like having your own personal back up group

on call.

Start play of the Auto Accompaniment rhythm

part.

Press

This enables chord input on the accompaniment

keyboard.

Use the accompaniment keyboard to play

chords.

This will cause bass and harmony Auto Accompaniment

parts to be added to the rhythm part.

Play other chords with left hand as you play the

melody with your right hand.

Pressing

again returns to rhythm only

accompaniment.

• For information about starting Auto Accompaniment as

soon as a chord is played, see “Using Synchro Start” on

page E-31.

You can select from among the following five chord input

modes.

• FINGERED 1

• FINGERED 2

• FINGERED 3

• CASIO CHORD

• FULL RANGE CHORD

Hold down

until the chord input mode

selection screen appears on the display.

Use the

(10-key) [–] and [+] keys to select the

chord input mode you want.

• For information about each chord input mode, see the

separate “Appendix”.

• If you do not perform any operation after the chord input

mode selection screen appears, the display will return

automatically to the screen that was displayed before

you held down

Playing All Parts

Auto Accompaniment with Chords

Example:Pressing D-F

-A-C on the accompaniment keyboard

Accompaniment for the D-F

-A-C chord (D7) sounds.

Accompaniment keyboard

Lights

Chords

(no melody played)

Melody

Selecting a Chord Input Mode

C h o r d

Chord input mode

English

Using Auto Accompaniment

E-29

■ FINGERED 1, 2, and 3

With these three input modes, you finger 3-note or 4-note

chords on the accompaniment keyboard. Note that with some

chords, even if you do not finger the third or fifth note, they will

be played anyway.

● FINGERED 1

Play the component notes of the chord on

the keyboard.

● FINGERED 2

Unlike FINGERED 1, 6th input is not

possible. m7 or m7

5 is input.

● FINGERED 3

Unlike FINGERED 1, allows input of

fraction chords with the lowest keyboard

note as the bass note.

■ CASIO CHORD

With CASIO CHORD, you can use

simplified fingerings to play the four types

of chords described below.

CASIO CHORD Fingering

• When playing a minor, seventh, or minor seventh chord, it

makes no different whether the additional keys you press

are black or white.

■ FULL RANGE CHORD

With this mode, you can use the full range

of the keyboard to play chords and the

melody.

Accompaniment keyboard

Chord Type Example

Major Chords

Letters above the accompaniment

keyboard indicate the chord

assigned to each key. Pressing a

single accompaniment area key in

the CASIO CHORD mode will play

the major chord whose name is

marked above the key. All of the

accompaniment area keys that are

marked with the same chord name

play exactly the same chord.

C (C Major)

Minor Chords

To play a minor chord, press the

accompaniment area key that

corresponds to the major chord,

while also pressing one other

accompaniment area key to the

right.

Cm (C Minor)

Seventh Chords

To play a seventh chord, press the

accompaniment area key that

corresponds to the major chord,

while also pressing two other

accompaniment area keys to the

right.

C7 (C Seventh)

Minor Seventh Chords

To play a minor seventh chord,

press the accompaniment area key

that corresponds to the major

chord, while also pressing three

other accompaniment area keys to

the right.

Cm7

(C Minor Seventh)

DE F F

DE F

DE F F

DE F

DE F F

DE F

DE F F

DE F

Accompaniment keyboard / Melody keyboard

Using Auto Accompaniment

E-30

Use the following procedures to play intro and ending

patterns, to play fill-in patterns, and to play variations of basic

Auto Accompaniment patterns.

■ Auto Accompaniment Variation

Each Auto Accompaniment pattern has a basic “normal

pattern” as well as a “variation pattern”.

Press

This starts the variation pattern.

Pressing

returns to normal pattern.

■ Auto Accompaniment Intro

Use the following procedure to play an intro of a few

measures.

Press

This starts the intro pattern. Normal pattern play will start

when the intro pattern is finished.

• If you press

while an intro pattern is being played,

the variation pattern will start when the intro pattern is

finished.

■ Auto Accompaniment Fill-in

Use the procedure below to play a fill-in pattern during a

performance.

• A “fill-in” is a short phrase played where you want to change

the mood of a piece. A fill-in pattern can be used to create a

link between two melodies or an accent.

• Normal and variation patterns have their own unique fill-in

patterns.

● Normal Pattern Fill-in

While a normal pattern is playing, press

This plays the fill-in for the normal pattern.

• Normal pattern play will resume after the fill in pattern is

complete.

● Variation Pattern Fill-in

While a variation pattern is playing, press

This plays the fill-in for the variation pattern.

• Variation pattern play will resume after the fill in pattern

is complete.

■ Auto Accompaniment Ending

Use the following procedure to play an ending of a few

measures.

While an Auto Accompaniment is playing, press

This will play the ending pattern and then stop Auto

Accompaniment play automatically.

Using Auto Accompaniment

Effectively

Auto Accompaniment Pattern Variations

Lights

English

Using Auto Accompaniment

E-31

■ Using Synchro Start

Use the following procedure to configure the Digital Keyboard

to start Auto Accompaniment play as soon as you press a

keyboard key.

Press

This enters accompaniment start standby.

Play a chord on the keyboard.

This will start full part accompaniment (normal).

Any of the following operations can be performed while in

synchro standby to start a non-normal pattern.

• To start with intro pattern, press

• To start with variation pattern play, press

Use the following procedure to change Auto Accompaniment

speed to a level that suits you.

Press

Use y (slower) and t (faster) to change the tempo

setting. Holding down either button changes the setting at

high speed.

•Pressing y and t at the same time will initialize the

rhythm setting in accordance with the currently selected

rhythm.

• While the tempo value is flashing, you also can use

(10-key) to change it.

• If you do not perform any operation for after the tempo

setting screen appears, the display will return to the

screen displayed before you pressed

Use the following procedure to adjust the balance between

what you are playing on the keyboard and the volume of the

Auto Accompaniment.

Press

a number of times until “AcompVol”

appears on the display (page E-4).

Use the

(10-key) [–] and [+] keys to adjust the

accompaniment volume.

With One-Touch Preset, the Digital Keyboard automatically

configures optimal tone, tempo, and other settings in

accordance with the rhythm pattern you select.

Hold down

until the current tone screen

appears on the display.

This will automatically apply the One-Touch Preset

settings in accordance with the rhythm pattern that is

currently selected.

Play a chord on the keyboard.

This will start accompaniment automatically.

Changing Auto Accompaniment Speed

(Tempo)

Flashes

Adjusting the Accompaniment Volume

Using One-Touch Preset

A c o m

V o l

E-32

Connecting External Devices

You can connect the Digital Keyboard to a computer and

exchange MIDI data between them. You can send play data

from the Digital Keyboard to music software running on your

computer, or you can send MIDI data from your computer to

the Digital Keyboard for playback.

The following shows the minimum computer system

requirements for sending and receiving MIDI data. Check to

make sure that your computer complies with these

requirements before connecting the keyboard to it.

• Operating System

Windows

XP (SP2 or later)

Windows Vista

Mac OS

X (10.3.9, 10.4.11 or later, 10.5.2 or later)

•USB port

• Never connect to a computer that does not conform to

the above requirements. Doing so can cause problems

with your computer.

• Make sure you follow the steps of the procedure below

exactly. Connecting incorrectly can make data send

and receive impossible.

Turn off the keyboard and then start up your

computer.

• Do not start up the music software on your computer

yet!

After starting up your computer, use a

commercially available USB cable to connect it

to the keyboard.

Turn on the keyboard.

• If this is the first time you are connecting the keyboard

to your computer, the driver software required to send

and receive data will be installed on your computer

automatically.

Start up your computer’s music software.

bnbn

blbl

Connecting a Computer

Minimum Computer System Requirements

*1: Windows XP Home Edition

Windows XP Professional (32- bit)

*2: Windows Vista (32- bit)

Connecting the Keyboard to Your Computer

Computer USB port

A connector

B connector

Keyboard USB port

USB cable

(A-B type)

English

Connecting External Devices

E-33

Configure the music software settings to select

one of the following as the MIDI device.

• For information about how to select the MIDI device,

see the user documentation that comes with the music

software you are using.

• Be sure to turn on the keyboard first before starting up

your computer’s music software.

• USB send and receive is disabled during playback of a

Song Bank song (page E-15).

• Once you are able to connect successfully, there is no

problem with leaving the USB cable connected when you

turn off your computer and/or keyboard.

• This Digital Keyboard conforms to General MIDI Level 1

(GM).

• For detailed specifications and connections that apply to

MIDI data send and receive by this keyboard, see the latest

support information provided by the website at the following

URL.

http://world.casio.com/

A keyboard channel is the channel used for sending Digital

Keyboard data to a computer. You can select the channel you

want for sending Digital Keyboard data to a computer.

Press

a number of times until “Keybd Ch”

appears on the display (page E-4).

Use the

(10-key) [–] and [+] keys to change

the keyboard channel.

The navigate channels can be used to display only the notes

of a particular channel (part) as on-screen guide information

from among the note information of a tune sent from the

computer.

■ Specifying the Navigate Channels

From among the 16 available channels (numbered 1 to 16),

you can specify any two neighboring channels (such as 05

and 06) as navigate channels. The smaller numbered channel

is the navigate (L) channel, while the larger numbered

channel is the navigate (R) channel. Specifying the navigate

(R) channel will automatically configure the navigate (L)

channel as well.

Press

a number of times until “Navi. Ch”

appears on the display (page E-4).

Use the

(10-key) to specify the navigate (R)

channel.

This also will automatically configure the next lower

channel number as the navigate (L) channel.

CASIO USB-MIDI: (For Windows Vista, Mac OS X)

USB Audio Device: (For Windows XP)

MIDI Settings

Keyboard Channel

Navigate Channels

K e

b d C h

N a v i . C h

Connecting External Devices

E-34

■ Turning Off the Navigate Channel Sound and

Playing the Part on the Keyboard

You can turn off the sound on one or both of the navigate

channels and play the cancelled part on the keyboard

yourself.

Press

to select the channel setting you want

to turn off.

Each press of

cycles through settings (1) thorough (4)

described below.

• If you turn off one channel, you can play the cancelled

part on the keyboard using the same tone as the

channel you turned off. If you turn off both channels

(option (3)), what you play on the keyboard sounds

using the tone of the navigate (R) channel.

There are times when exchanging data with a computer when

you may not want the Digital Keyboard to sound notes you

play on its keyboard. The local control setting lets you do just

that.

Press

a number of times until “Local”

appears on the display (page E-4).

Use the

(10-key) [–] and [+] keys to specify

the local control setting.

Enabling the Accomp Out setting causes Auto

Accompaniment data to be sent to the computer.

Press

a number of times until “AcompOut”

appears on the display (page E-4).

Use the

(10-key) [–] and [+] keys to turn

Accomp Out on or off.

Navigate (L)

Channel

Navigate (R)

Channel

Sound

On-

screen

Guide

Sound

On-

screen

Guide

(1) R only displayed { ××{

(2) L only displayed × {{ ×

(3) LR displayed × { × {

(4) LR nor displayed {{{{

Selected channel indicator appears.

Local Control

Accomp Out

L o c a l

A c o m

O u t

English

Connecting External Devices

E-35

This keyboard can be connected to commercially available

stereo, amplifier, or recording equipment, to a portable audio

player or other equipment.

Connection requires commercially available connecting cords,

supplied by you. The connecting cords should have a stereo

standard plug on one end and a plug that matches the

configuration of the external device on the other end.

• Turn off the external device when making connections.

After connecting, turn down the keyboard and external

device volume levels whenever turning power on or off.

• After connecting, turn on the Digital Keyboard and then

the external device.

• If keyboard notes sound distorted when they are

sounded from external audio equipment, lower the

keyboard’s volume setting.

Connection requires commercially available connecting cords,

supplied by you. The connecting cords should have a stereo

mini plug on one end and a plug that matches the

configuration of the external device on the other end.

• Turn off the keyboard when making connections. After

connecting, turn down the keyboard and external

device volume levels whenever turning power on or off.

• After connecting, turn on the external device and then

the Digital Keyboard.

• If notes are distorted when they are sounded on the

external device, lower the volume setting of the

external device.

Connecting to Audio Equipment

Outputting Keyboard Notes to Audio

Equipment

Playing an External Device from the

Keyboard

Keyboard PHONES/

OUTPUT jack

Audio equipment, amplifier,

etc.

Stereo standard plug

Keyboard AUDIO IN jack

Portable audio player, etc.

Stereo mini plug

E-36

Reference

Troubleshooting

Symptom Action

Included Accessories

I can’t find something that should be here. Carefully check inside all of the packing materials.

Power Requirements

Power will not turned on. • Check the AC adaptor or make sure that the batteries are facing

correctly (page E-5).

• Replace the batteries with new ones or switch over to AC adaptor

power (page E-5).

The Digital Keyboard outputs a loud sound and then

suddenly powers down.

Replace the batteries with new ones or switch over to AC adaptor

power (page E-5).

The Digital Keyboard suddenly powers down after a

few minutes.

This happens when Auto Power Off (page E-6) is triggered.

Display

The display keeps going out or are flashing. Replace the batteries with new ones or switch over to AC adaptor

power (page E-5).

On-screen keyboard keys or notes remain on the

display.

A Step Up Lesson is in progress and the Digital Keyboard is waiting

for you to play the next note in the song. To stop this from happening,

cancel the lesson (page E-21).

Screen contents are visible only from straight ahead. This is dues to production limitations. It does not indicate malfunction.

Sound

Nothing happens when I press any keyboard key. • Adjust the main volume setting (page E-6).

• Check if something is plugged into the PHONES/OUTPUT jack (

)

on the back of the Digital Keyboard.

• Turn power off and then back on to initialize all keyboard settings

(page E-6).

Nothing happens or notes do not play normally when

I play notes on the left side of the keyboard.

Press

to disable chord input in the accompaniment keyboard area

(page E-28).

Nothing happens when I start an Auto

Accompaniment.

• With rhythms 140, and 142 to 150, nothing will sound until you play

a chord on the keyboard. Try playing a chord (page E-28).

• Check and adjust the accompaniment volume setting (page E-31).

• Turn power off and then back on to initialize all keyboard settings

(page E-6).

Nothing happens when I start playback of a built-in

song.

• It takes a little time after you press the button until the song starts to

play. Wait for a moment for the song to start.

• Check and adjust the song volume (page E-17).

• Turn power off and then back on to initialize all keyboard settings

(page E-6).

The metronome does not sound. • Check and adjust the accompaniment volume setting (page E-31).

• Check and adjust the song volume (page E-17).

• Turn power off and then back on to initialize all keyboard settings

(page E-6).

Notes keep sounding, without stopping. • Turn power off and then back on to initialize all keyboard settings

(page E-6).

• Replace the batteries with new ones or switch over to AC adaptor

power (page E-5).

English

Reference

E-37

Some notes are cut off while they are playing. Notes are cut off whenever the number of notes being sounded

exceeds the maximum polyphony value of 48 (24 for some tones).

This does not indicate malfunction. See “Maximum Polyphony” in the

“Tone List” in the separate “Appendix”.

The volume or tone setting I made has changed. • Adjust the main volume setting (page E-6).

• Turn power off and then back on to initialize all keyboard settings

(page E-6).

• Replace the batteries with new ones or switch over to AC adaptor

power (page E-5).

Output volume does not change even though is

change my keyboard touch (CTK-3000 only).

• Change the Touch Response setting (page E-7).

• Turn power off and then back on to initialize all keyboard settings

(page E-6).

In certain keyboard ranges, the volume and tone

quality sound are slightly different from those in other

keyboard ranges.

This is due to system limitations. It does not indicate malfunction.

With some tones, octaves do not change at the far

ends of the keyboard.

This is due to system limitations. It does not indicate malfunction.

The pitch of the notes does not match other

accompanying instruments or sounds strange when

played long with other instruments.

• Check and adjust the transpose (page E-11) and tuning settings

(page E-11).

• Turn power off and then back on to initialize all keyboard settings

(page E-6).

The reverb of notes seems to change suddenly. • Check and adjust the reverb setting (page E-10).

• Turn power off and then back on to initialize all keyboard settings

(page E-6).

Sounds I sampled were deleted. Sampled data is deleted whenever keyboard power is turned off (page

E-13).

Operation

When I perform a skip forward or skip back

operation, the skip operation moves multiple song

measures instead of only a single measure.

While song playback is stopped or a Step Up Lesson is in progress,

skip forward and skip back operations are performed in phrase units

(page E-16).

Computer Connection

I can’t exchange data between the Digital Keyboard

and a computer.

• Check to make sure that the USB cable is connected to the

keyboard and computer, and that the device is selected correctly

with your computer’s music software settings (page E-32).

• Turn off the keyboard and then exit the music software on your

computer. Next, turn the keyboard back on and then restart the

music software on your computer.

Symptom Action

Reference

E-38

Specifications

Models CTK-2000/CTK-3000

Keyboard 61 standard-size keys

Touch Response

(CTK-3000 only) 2 types, Off

Maximum Polyphony 48 notes (24 for certain tones)

Tones

Built-in Tones 400

Sampling Tones 1

Sampling time: 1 second (fixed)

Effects: 10 types

Reverb 1 to 10, Off

Metronome

Beats per Measure 0, 2 to 6

Tempo Range 30 to 255

Song Bank

Tunes 110

Step Up Lesson

Lessons 4 (Listen, Watch, Remember, Auto)

Lesson Part L, R, LR

Functions Repeat, Voice Fingering Guide, Note Guide, Performance Evaluation

Music Challenge 20 notes

Auto Accompaniment

Rhythm Patterns 150

Other Functions

Transpose ±1 octaves (–12 to +12 semitones)

Tuning A4 = approx. 440 Hz ±100 cents

MIDI 16 multi-timbre received, GM Level 1 standard

Musical Information Function Tone, Rhythm, Song Bank, numbers and names; staff notation, fingering, pedal operation,

tempo, measure and beat number, chord name, etc.

Pitch Bend Wheel

(CTK-3000 only)

Pitch Bend Range 0 to 12 semitones

Inputs/Outputs

USB port TYPE B

Sustain jack Standard jack (sustain, sostenuto, soft, rhythm start/stop)

Phones/Output jack Stereo standard jack

Output Impedance: 200Ω, Output Voltage: 4.8V (RMS) MAX

Audio In jack Stereo mini jack

Input Impedance: 40kΩ, Input Sensitivity: 200mV

Power Jack 9V DC

Power Supply 2-way

Batteries 6 AA-size zinc-carbon batteries or alkaline batteries

Battery Life Approximately 4 hours continuous operation on alkaline batteries

AC Adaptor AD-5

Auto Power Off Approximately 6 minutes after last key operation (Operates during battery use only)

Speakers 10cm × 2

Output 2W + 2W

English

Reference

E-39

• Design and specifications are subject to change without notice.

Be sure to read and observe the following operating precautions.

■ Location

Avoid the following locations for this product.

• Areas exposed to direct sunlight and high humidity

• Areas subjected to temperature extremes

• Near a radio, TV, video deck, or tuner

The above devices will not cause malfunction of the product, but interference from the product can cause audio or video

interference of a nearby device.

■ User Maintenance

• Never use benzene, alcohol, thinner, or other chemical agents to clean the product.

• To clean the product or its keyboard, wipe with a soft cloth moistened in a weak solution of water and a mild neutral detergent.

Wring all excess moisture from the cloth before wiping.

■ Included and Optional Accessories

Use only accessories that are specified for use with this product. Use of unauthorized accessories creates the risk of fire, electric

shock, and personal injury.

■ Weld Lines

Lines may be visible on the exterior of the product. These are “weld lines” that result from the plastic molding process. They are not

cracks or scratches.

■ Musical Instrument Etiquette

Always be aware of others around you whenever using this product. Be especially careful when playing late at night to keep the

volume at levels that do not disturb others. Other steps you can take when playing late at night are closing the window and using

headphones.

Power Consumption 9V = 7.7W

Dimensions 94.9 × 35.4 × 11.2 cm (37

/8 × 13

/16 × 4

/16 inch)

Weight CTK-2000: Approximately 3.8kg (8.4 lbs) (without batteries)

CTK-3000: Approximately 3.9kg (8.6 lbs) (without batteries)

Operating Precautions

Reference

E-40

Song List

SONG BANK

WORLD

001 TWINKLE TWINKLE LITTLE STAR

002 LIGHTLY ROW

003 LONG LONG AGO

004 ON TOP OF OLD SMOKEY

005 SAKURA SAKURA

006 WHEN THE SAINTS GO MARCHING IN

007 AMAZING GRACE

008 AULD LANG SYNE

009 COME BIRDS

010 DID YOU EVER SEE A LASSIE?

011 MICHAEL ROW THE BOAT ASHORE

012 DANNY BOY

013 MY BONNIE

014 HOME SWEET HOME

015 AURA LEE

016 HOME ON THE RANGE

017 ALOHA OE

018 SANTA LUCIA

019 FURUSATO

020 GREENSLEEVES

021 JOSHUA FOUGHT THE BATTLE OF JERICHO

022 THE MUFFIN MAN

023 LONDON BRIDGE

024 UNDER THE SPREADING CHESTNUT TREE

025 SIPPIN’ CIDER THROUGH A STRAW

026 GRANDFATHER’S CLOCK

027 ANNIE LAURIE

028 BEAUTIFUL DREAMER

029

IF YOU’RE HAPPY AND YOU KNOW IT, CLAP YOUR

HANDS

030 MY DARLING CLEMENTINE

031 LITTLE BROWN JUG

032 HOUSE OF THE RISING SUN

033 SHE WORE A YELLOW RIBBON

034 YANKEE DOODLE

035 MY OLD KENTUCKY HOME

036 SZLA DZIEWECZKA

037 TROIKA

038 WALTZING MATILDA

039 ON THE BRIDGE OF AVIGNON

040 I’VE BEEN WORKING ON THE RAILROAD

041 OH! SUSANNA

042 CAMPTOWN RACES

043 JEANNIE WITH THE LIGHT BROWN HAIR

044 TURKEY IN THE STRAW

045 JAMAICA FAREWELL

EVENT

046 SILENT NIGHT

047 WE WISH YOU A MERRY CHRISTMAS

048 JINGLE BELLS

049 JOY TO THE WORLD

050 O CHRISTMAS TREE

PIANO/CLASSICS

051 MARY HAD A LITTLE LAMB

052 LE CYGNE FROM “LE CARNAVAL DES ANIMAUX”

053 JE TE VEUX

054 SONATA op.13 “PATÉTIQUE” 2nd Mov.

055 HEIDENRÖSLEIN

056 AIR FROM “SUITE no.3”

057 SPRING FROM “THE FOUR SEASONS”

058 HABANERA FROM “CARMEN”

059 BRINDISI FROM “LA TRAVIATA”

060 HUNGARIAN DANCES no.5

061 MINUET IN G MAJOR

062 MUSETTE IN D MAJOR

063 GAVOTTE (GOSSEC)

064 ARABESQUE (BURGMÜLLER)

065 CHOPSTICKS

066 DECK THE HALL

067 ODE TO JOY

068 AVE MARIA (GOUNOD)

069 SONATINA op.36 no.1 1st Mov.

070 PRELUDE op.28 no.7 (CHOPIN)

071 RÊVERIE

072 GYMNOPÉDIES no.1

073 GOING HOME FROM “FROM THE NEW WORLD”

074 FÜR ELISE

075 TURKISH MARCH (MOZART)

076 SONATA op.27 no.2 “MOONLIGHT” 1st Mov.

077 ETUDE op.10 no.3 “CHANSON DE L’ADIEU”

078 THE ENTERTAINER

079

WEDDING MARCH FROM “MIDSUMMER NIGHT’S

DREAM”

080 AMERICAN PATROL

081 FRÖHLICHER LANDMANN

082 LA CHEVALERESQUE

083 SONATA K.545 1st Mov.

084 LA PRIÈRE D’UNE VIERGE

085 VALSE op.64 no.1 “PETIT CHIEN”

086 LIEBESTRÄUME no.3

087 JESUS BLEIBET MEINE FREUDE

088 CANON (PACHELBEL)

089 SERENADE FROM “EINE KLEINE NACHTMUSIK”

090 MARCH FROM “THE NUTCRACKER”

EXERCISE

091-100 EXERCISE I

101-110 EXERCISE II

English

Reference

E-41

Chord Chart

/(D

)

)/E

/(G

)

)/A

)/B

dim m7

-5

M77 m7 dim7

Chord

Type

Root

/(D

)

)/E

/(G

)

)/A

)/B

sus4aug add97

-5

7sus4 m add9 mM7

Chord

Type

Root

Function Transmitted Recognized Remarks

Basic

Channel

1 - 16

Default

Changed

Note

Number

0 - 127

36 - 96

True voice

After

Touch

Control

Change

(CTK-2000)

(CTK-3000)

Pitch Bender

Key’s

Ch’s

Velocity

9nH v = 0

100

(CTK-2000)

1 - 127

(CTK-3000)

9nH v =

9nH v = 1 - 127

9nH v = 0, 8nH V =

Note ON

Note OFF

Mode

Mode 3

Default

Messages

Altered

0, 32

6, 38

Bank select

Modulation

Data entry

Volume

Pan

Expression

Hold 1

Models: CTK-2000/CTK-3000 Version : 1.0

(CTK-2000)

(CTK-3000)

(MSB only)

**: no relation

**:sin relación

MIDI Implementation Chart

Program

Change

:True #

System Exclusive

System

Common

: Song Pos

: Song Sel

: Tune

Aux

Messages

Remarks

: Local ON/OFF

: All notes OFF

: Active Sense

: Reset

System

Real Time

: Clock

: Commands

100, 101

120

121

Sostenuto

Soft pedal

Reverb send

RPN LSB, MSB

All sound off

Reset all controller

Mode 1 : OMNI ON, POLY

Mode 3 : OMNI OFF, POLY

Mode 2 : OMNI ON, MONO

Mode 4 : OMNI OFF, MONO

O : Yes

X : No

(CTK-2000)

(CTK-3000)

*1: Depends on tone.

2: RPN : Pitch Bend Sensitivity (CTK-3000 only)

3: RPN : Pitch Bend Sensitivity, Fine Tune, Coarse Tune

4: In accordance with pedal effect setting.

5: Universal System Exclusive Messages :

Master Fine Tuning, Master Coarse Tuning, Reverb Time

6: Universal System Exclusive Messages :

GM System On/Off, Master Fine Tuning, Master Coarse Tuning, Reverb Time

• For details about footnotes 2, 3, 5, 6, see MIDI Implementation at

http://world.casio.com/.

*1: Depende del tono.

*2: RPN : Sensibilidad a la inflexión de altura tonal (sólo CTK-3000)

*3:

RPN : Sensibilidad a la inflexión de altura tonal, afinación precisa, afinación aproximada

*4: De acuerdo con el ajuste de efecto de pedal.

*5: Mensajes exclusivos de sistema universal :

Afinación maestra precisa, afinación maestra aproximada, tiempo de reverberación

*6: Mensajes exclusivos de sistema universal :

Sistema GM activado/desactivado, afinación maestra precisa,

afinación maestra aproximada, tiempo de reverberación

• Si desea información sobre las notas al pie de página 2, 3, 5, 6, consulte

Implementación MIDI en http://world.casio.com/

MA0811-B Printed in China

CTK2000/3000ES1B

This recycle mark indicates that the packaging conforms to

the environmental protection legislation in Germany.

Esta marca de reciclaje indica que el empaquetado se

ajusta a la legislación de protección ambiental en Alemania.

Casio CTK-2000 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Casio CTK-2000

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info