624485
9
Verklein
Vergroot
Pagina terug
1/10
Pagina verder
E-64
Auto light precautions
Illumination may not turn on if the face of the watch is more than 15 degrees above
or below parallel. Make sure that the back of your hand is parallel to the ground.
Illumination turns off after the preset illumination duration (page E-61), even if you
keep the watch pointed towards your face.
Static electricity or magnetic force can interfere with proper operation of auto light.
If illumination does not turn on, try moving the watch back to the starting position
(parallel with the ground) and then tilt it back towards your face again. If this does
not work, drop your arm all the way down so it hangs at your side, and then bring it
back up again.
You may notice a very faint clicking sound coming from the watch when it is shaken
back and forth. This sound is caused by mechanical operation of auto light, and
does not indicate a problem with the watch.
E-65
Button Operation Tone
When enabled, the button operation tone sounds any time you press one of the watch’s buttons. You can
enable or disable the button operation tone as desired.
Even if you disable the button operation tone, the alarm, Hourly Time Signal, and Countdown Timer
Mode alarm all operate normally.
To enable or disable the button operation tone
1. In the Timekeeping Mode, hold down
A
until
ADJ
appears on the display.
When you release
A
(after ADJ appears), the second hand will be pointing at the currently
selected city code.
2. Use
D
to cycle through settings on the display until the current button
operation tone setting (
MUTE
or
KEY
) is shown.
See the sequence in step 2 of the procedure under “To change the
current time and date settings” (page E-17) for information about
how to scroll through setting screens.
3. Press
E
to toggle the button operation tone setting between enabled (
KEY
) and disabled (
MUTE
).
4. After the setting is the way you want, press
A
to exit the setting screen.
E-66
Low Battery Indication
A low battery indicator appears on the display when the power of the batteries is low. Have the batteries
replaced as soon as possible.
Note
For guidelines covering the life of the batteries and supported battery types, see “Speci cations”
(page E-72).
The conditions below are in effect while the low battery indicator is fl ashing.
All hands are stopped.
Except for the low battery indicator, all other display functions are
disabled.
Watch tones are disabled.
Display illumination is disabled.
Watch operations are disabled.
Note
Sequentially or repeatedly performing sensor, light, alarm, and other power intensive operations
over a short period can cause a sudden drop in battery power, which will make the low battery
indicator fl ash. Even though the low battery indicator may disappear and watch functions may
become re-enabled, battery replacement is recommended.
Low battery indicatorLow battery indicator
E-67
Troubleshooting
Time Setting
The current time setting is off by a couple of hours.
Your Home City setting may be wrong (page E-15). Check your Home City setting and correct it, if
necessary.
The current time setting is off by one hour.
You may need to change your Home City’s standard time/daylight saving time (DST) setting. Use the
procedure under “To change the current time and date settings” (page E-17).
World Time Mode
The time for my World Time City is off in the World Time Mode.
This could be due to incorrect switching between standard time and daylight saving time.
See “To confi gure World Time City and summer time settings” (page E-52) for more information.
E-68
Batteries
The low battery indicator is fl ashing on the digital display.
The watch’s battery power is low. Have the batteries replaced as soon as
possible.
See “Low Battery Indication” (page E-66).
Low battery indicatorLow battery indicator
E-69
Direction and Temperature Readings
The temperature unit setting won’t change.
The temperature unit setting is always Celsius (
°C
) whenever
TOKYO
is selected as the Home City. In
this case, the setting cannot be changed.
“ERR” appears while a sensor operation is in progress.
Subjecting the watch to strong impact can cause sensor malfunction or improper contact of internal
circuitry. When this happens,
ERR
(error) will appear on the display and sensor operations will be
disabled.
Digital Compass
Operation
Temperature
Measurement
If
ERR
appears while a measurement operation is being performed in a sensor mode, restart the
measurement. If
ERR
appears on the display again, it can mean there is something wrong with the
sensor.
If
ERR
keeps appearing during measurement, it could mean there is a problem with the applicable
sensor.
E-70
Direction Readings
Abnormal magnetism detection is indicated.
Move away from any potential source of strong magnetism and try
taking a reading again.
If abnormal magnetism is detected again when you retry, it could mean
that the watch itself has become magnetized. If this happens, continue
to keep away from the source of strong magnetism, perform
bidirectional calibration, and then try taking a reading again. For more
information, refer to “To perform bidirectional calibration” (page E-26)
and “Location” (page E-32).
“ERR” appears on the display following bidirectional calibration.
If
- -
appears and then changes to
ERR
(error) on the calibration screen, it means that there is something
wrong with the sensor.
If
ERR
disappears after about one second, try performing the calibration again.
If
ERR
keeps appearing, contact your original dealer or nearest authorized CASIO distributor to have
the watch checked.
Whenever you have a sensor malfunction, take the watch to your original dealer or nearest authorized
CASIO distributor as soon as possible.
E-71
Incorrect direction readings.
Incorrect bidirectional calibration. Perform bidirectional calibration (page E-26).
Nearby source of strong magnetism, such as a household appliance, a large steel bridge, a steel
beam, overhead wires, etc., or an attempt to perform direction measurement on a train, boat, etc. Move
away from large metal objects and try again.
Different results produced by direction readings taken at the same location.
Magnetism generated by nearby high-tension wires is interfering with detection of terrestrial magnetism.
Move away from the high-tension wires and try again.
Problems taking direction readings indoors.
A TV, personal computer, speakers, or some other object is interfering with terrestrial magnetism
readings. Move away from the object causing the interference or take the direction reading outdoors.
Indoor direction readings are particularly diffi cult inside ferro-concrete structures.
Remember that you will not be able to take direction readings inside of trains, airplanes, etc.
Operation Guide 5442 5443
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Casio 5442 - GN-1000 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Casio 5442 - GN-1000 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,05 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Casio 5442 - GN-1000

Casio 5442 - GN-1000 Gebruiksaanwijzing - Deutsch - 10 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info