645136
5
Verklein
Vergroot
Pagina terug
1/6
Pagina verder
E-32
To turn an alarm and the Hourly Time Signal on and off
1. In the Alarm Mode, use
D
to select an alarm or the Hourly Time Signal.
2. When the alarm or the Hourly Time Signal you want is selected, press
A
to turn it on and off.
The alarm on indicator (when any alarm is on), snooze alarm indicator
(when the snooze alarm is on), and the Hourly Time Signal on indicator
(when the Hourly Time Signal is on) are shown on the upper display in
all modes.
To stop the alarm
Press any button.
Hourly time signal
on indicator
Alarm on indicator
Snooze alarm
indicator
Hourly time signal
on indicator
Alarm on indicator
Snooze alarm
indicator
E-33
Illumination
The face of the watch is illuminated for easy reading in the dark. The
watch’s auto light switch turns on illumination automatically when you
angle the watch towards your face.
The auto light switch must be enabled (page E-35) for it to operate.
To turn on illumination manually
Press
B
in any mode (except when a fl ashing setting screen is
displayed) to turn on illumination.
You can use the procedure below to select either 1.5 seconds or three
seconds as the illumination duration. When you press
B
, the
illumination will remain on for about 1.5 seconds or three seconds,
depending on the current illumination duration setting.
The above operation turn on illumination regardless of whether the auto
light switch is enabled or disabled.
Illumination is disabled while confi guring sensor measurement mode
settings.
To change the illumination duration
1. In the Timekeeping Mode, hold down
A
until
ADJ
appears in the upper display.
When you release
A
(after ADJ appears), SET will be fl ashing in the lower display. This is the
setting mode.
2. Use
C
to cycle through the settings on the lower display until the current illumination duration (
LT1
or
LT3
) is shown.
See the sequence in step 2 of the procedure under “To change the current time and date
settings” (page E-14) for information about how to scroll through setting screens.
E-34
3. Press
D
to toggle the illumination duration between three seconds (
LT3
displayed) and 1.5 seconds
(
LT1
displayed).
4. After all of the settings are the way you want, press
A
to exit the setting screen.
About the Auto Light Switch
While the Auto Light Switch is enabled, illumination will turn on
whenever you position your wrist as described below in any mode.
Moving the watch to a position that is parallel to the ground and
then tilting it towards you more than 40 degrees causes
illumination to turn on.
Warning!
Always make sure you are in a safe place whenever you are reading the display of the watch
using the auto light switch. Be especially careful when running or engaged in any other activity
that can result in accident or injury. Also take care that sudden illumination by the auto light
switch does not startle or distract others around you.
When you are wearing the watch, make sure that its auto light switch is turned off before riding
on a bicycle or operating a motorcycle or any other motor vehicle. Sudden and unintended
operation of the auto light switch can create a distraction, which can result in a traffi c accident
and serious personal injury.
More than
40°
Wear the watch on the
outside of your wrist
More than
40°
Wear the watch on the
outside of your wrist
E-35
Note
The auto light switch is always disabled, regardless of its enabled/disabled setting, when any one of
the following conditions exists.
While an alarm is sounding
During sensor measurement
To enable or disable the auto light switch
In the Timekeeping Mode, hold down
B
for about three seconds to
toggle the auto light switch between enabled (
LT
shown in the upper
display) and disabled (
LT
not displayed).
The auto light switch enabled indicator (
LT
) is on the upper display in
all modes while the auto light switch is turned enabled.
The auto light switch remains enabled for about six hours. After that
disables automatically.
Illumination Precautions
Illumination may be hard to see when viewed under direct sunlight.
Illumination will not turn on while an alarm is sounding, while high-speed hand movement is in progress,
while a sensor is taking a reading. Illumination will turn on if
B
is pressed between sensor reading
operations.
Illumination turns off automatically whenever an alarm sounds.
Frequent use of illumination runs down the battery.
Auto light switch
enabled indicator
Auto light switch
enabled indicator
E-36
Auto light switch precautions
Illumination may not turn on if the face of the watch is more than 15 degrees above
or below parallel. Make sure that the back of your hand is parallel to the ground.
Illumination turns off after the preset illumination duration (page E-33), even if you
keep the watch pointed towards your face.
Static electricity or magnetic force can interfere with proper operation of the auto
light switch. If illumination does not turn on, try moving the watch back to the
starting position (parallel with the ground) and then tilt it back towards your face
again. If this does not work, drop your arm all the way down so it hangs at your
side, and then bring it back up again.
You may notice a very faint clicking sound coming from the watch when it is shaken
back and forth. This sound is caused by mechanical operation of the auto light
switch, and does not indicate a problem with the watch.
E-37
Button Operation Tone
When enabled, the button operation tone sounds any time you press one of the watch’s buttons. You can
enable or disable the button operation tone as desired.
Even if you disable the button operation tone, the alarm, and Hourly Time Signal all operate normally.
To enable or disable the button operation tone
1. In the Timekeeping Mode, hold down
A
until
ADJ
appears in the
upper display.
When you release
A
(after ADJ appears), SET will be fl ashing in
the lower display.
2. Use
D
to cycle through settings on the upper display until the current
button operation tone setting (
MUTE
or
KEY
) is shown.
See the sequence in step 2 of the procedure under “To change the
current time and date settings” (page E-14) for information about
how to scroll through setting screens.
3. Press
D
to toggle the button operation tone setting between enabled
(
KEY
) and disabled (
MUTE
).
4. After the setting is the way you want, press
A
to exit the setting
screen.
Note
The mute indicator is displayed in all modes when the button
operation tone is disabled.
Mute indicatorMute indicator
E-38
Troubleshooting
Time Setting
Why is the current time setting off by a couple of hours?
Your Home City setting may be wrong (page E-12). Check your Home City setting and correct it, if
necessary.
Why is the current time setting off by one hour?
You may need to change your Home City’s standard time/daylight saving time (DST) setting. Use the
procedure under “To change the current time and date settings” (page E-14) to change the standard time/
daylight saving time (DST) setting.
Sensor modes
Why can’t I change the temperature unit setting?
The temperature unit setting is always Celsius (
°C
) whenever
TOKYO
is selected as the Home City. In
this case, the setting cannot be changed.
Why does “ERR” appear while a sensor operation is in progress?
Subjecting the watch to strong impact can cause sensor malfunction or improper contact of internal
circuitry. When this happens,
ERR
(error) will appear on the upper display and sensor operations will be
disabled.
E-39
Temperature
Measurement
If
ERR
appears while a measurement operation is being performed in a sensor mode, restart the
measurement. If
ERR
appears on the upper display again, it can mean there is something wrong with
the sensor.
If
ERR
keeps appearing during measurement, it could mean there is a problem with the applicable
sensor.
World Time Mode
The time for my World Time City is off in the World Time Mode.
This could be due to incorrect switching between standard time and daylight saving time.
See “To specify standard time or daylight saving time (DST) for a city” (page E-28) for more information.
Operation Guide 5418
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Casio 5418 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Casio 5418 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,78 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Casio 5418

Casio 5418 Gebruiksaanwijzing - Deutsch - 6 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info