624484
1
Verklein
Vergroot
Pagina terug
1/15
Pagina verder
MO1405-EA
© 2014 CASIO COMPUTER CO., LTD.
E-1
ENGLISH
Congratulations upon your selection of this CASIO watch.
Applications
The built-in sensors of this watch measure direction, barometric pressure, temperature and altitude.
Measured values are then shown on the display. Such features make this watch useful when hiking,
mountain climbing, or when engaging in other such outdoor activities.
Warning !
The measurement functions built into this watch are not intended for taking measurements that
require professional or industrial precision. Values produced by this watch should be considered
as reasonable representations only.
When engaging in mountain climbing or other activities in which losing your way can create a
dangerous or life-threatening situation, always use a second compass to confi rm direction readings.
Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any damage or loss
suffered by you or any third party arising through the use of this product or its malfunction.
E-2
Important!
The watch’s Altimeter Mode calculates and displays relative altitude based on barometric pressure
readings produced by its pressure sensor. This means that readings taken at different times at the
same location may produce different altitude values due to changes in barometric pressure. Also note
that the value displayed by the watch may be different from the actual elevation and/or sea level
elevation indicated for the area where you are located.
When using the altimeter of this watch for mountain climbing or other activities, it is highly
recommended that you check a map, local altitude indications, or some other source for your current
correct altitude and regularly calibrate the altimeter with the latest information. For more information,
see “To specify a reference altitude value” (page E-66).
Whenever you use the digital compass of this watch for serious trekking, mountain climbing, or other
activities, be sure always to take along another compass to confi rm readings. If the readings produced
by the digital compass of this watch are different from those of the other compass, perform bidirectional
calibration of the digital compass to ensure more accurate readings.
Direction readings and digital compass calibration will not be possible if the watch is in the vicinity of a
permanent magnet (magnetic accessory, etc.), metal objects, high-voltage wires, aerial wires, or
electrical household appliances (TV, computer, cellphone, etc.)
E-3
About This Manual
Depending on the model of your watch, digital display text appears
either as dark fi gures on a light background, or light fi gures on a dark
background. All examples in this manual are shown using dark fi gures
on a light background.
Button operations are indicated using the letters shown in the
illustration.
Note that the product illustrations in this manual are intended for
reference only, and so the actual product may appear somewhat
different than depicted by an illustration.
Crown
Small hand
Second Hand
Minute HandHour Hand
Crown
Small hand
Second Hand
Minute HandHour Hand
E-4
Using the Crown
This watch has a lock-type crown.
Important!
You should keep the crown locked during normal daily use. Leaving the crown unlocked creates the
risk of unintended operations or even damage due to impact.
To lock the crown
1. Push the crown back in (see “To pull out, rotate, or push the crown in”
below).
Note that attempting to lock the crown when it is not pushed in can
cause unexpected watch operation.
2. Rotate the crown so Mark 1 is aligned with Mark 2.
3. While pushing in on the crown (a), rotate it to the right (b) until it stops,
and align Mark 1 with Mark 3.
4. Gently pull on the crown to make sure it is securely locked and does
not come out.
To unlock the crown
Rotate the crown so Mark 1 aligns with Mark 2.
b
a
Mark 2
Mark 1
Mark 1
Mark 3
b
a
Mark 2
Mark 1
Mark 1
Mark 3
E-5
To pull out, rotate, or push the crown in
Important!
Before performing any of these operations, fi rst unlock the crown.
The illustrations below show the different crown operations.
Pull out Rotate Push in
E-6
High-speed Movement
You can use either of the crown operations described below to move watch hands or indicators at high
speed.
HS1: Can be used to move both hands and display indicators.
HS2: Can be used when setting the hour and minute manually to move the hands at high speed.
To start HS1 high-speed movement
While the crown is pulled out, rotate it rapidly three turns away from you (for
forward movement) or towards you (for reverse movement). High-speed
movement will continue even if you release the crown.
To start HS2 high-speed movement
While HS1 high-speed movement is in progress, again rotate the crown rapidly
three turns in the same direction as the current HS1 movement (away from you
for forward movement or towards you for reverse movement).
To stop high-speed movement
Rotate the crown in the direction that is opposite that of the current high-speed
movement or press any button.
E-7
Note
If you do not perform any operation for more than two minutes after pulling out the crown, the indicator
shown below will appear and crown operations will become disabled. If this happens, push the crown
back in and then pull it out again to re-enable crown operations.
Even if the indicator shown below appears immediately after you pull out the crown, crown operations
are disabled. If this happens, push the crown back in and lock it.
1 second
You can use high-speed movement in the following cases: when changing the time and/or date setting
in the Timekeeping Mode, Countdown Timer Mode, or Alarm Mode, or when performing magnetic
declination angle calibration, altitude calibration, barometric pressure calibration, or temperature
calibration operations.
Operation Guide 5371
E-8
Things to check before using the watch
1. Check the battery power level.
In any mode, hold down
B
for at least two seconds. The battery power indicator will appear on the digital
display, and then the watch will enter the Timekeeping Mode.
The battery power level will be indicated as H or M on the left
side of the digital display.
Go to step 2.
Power is low.
Charge the watch by placing it in a location
where it is exposed to light. For details, see “Charging the
Watch” (page E-14).
NO
YES
YES
Does any one of the following conditions exist?
L flashing on the digital display.
CHARGE” is flashing on the display.
The watch is charged
sufficiently.
NEXT
Battery power
indicator
When
L
is fl ashing, the second hand will jump at two-second intervals.
When
CHARGE
is fl ashing, all hands will move to and stop at 12 o’clock.
E-9
2. Check the Home City and the daylight saving time (DST) setting.
Use the procedure under “To confi gure Home City and summer time settings” (page E-34) to confi gure
your Home City and daylight saving time settings.
Important!
Proper time calibration signal reception, and World Time Mode data depend on correct Home City,
time, and date settings in the Timekeeping Mode. Make sure you confi gure these settings correctly.
3. Set the current time.
To set the time using a time calibration signal
See “To get ready for a receive operation” (page E-22).
To set the time manually
See “Confi guring Current Time and Date Settings Manually” (page E-36).
The watch is now ready for use.
For details about the watch’s radio controlled timekeeping feature, see “Radio Controlled Atomic
Timekeeping” (page E-20).
E-10
Contents
About This Manual …………………………………………………………………………………………… E-3
Using the Crown ……………………………………………………………………………………………… E-4
To lock the crown ……………………………………………………………………………………… E-4
To unlock the crown …………………………………………………………………………………… E-4
To pull out, rotate, or push the crown in ……………………………………………………………… E-5
Things to check before using the watch ………………………………………………………………… E-8
Charging the Watch ………………………………………………………………………………………… E-14
To recover from the sleep state …………………………………………………………………… E-19
Radio Controlled Atomic Timekeeping ………………………………………………………………… E-20
To get ready for a receive operation ……………………………………………………………… E-22
To perform manual receive ………………………………………………………………………… E-24
To check the latest signal reception results ……………………………………………………… E-26
To turn auto receive on or off ……………………………………………………………………… E-27
Mode Reference Guide …………………………………………………………………………………… E-29
Timekeeping ………………………………………………………………………………………………… E-33
Confi guring Home City Settings ………………………………………………………………………… E-34
To confi gure Home City and summer time settings ……………………………………………… E-34
Confi guring Current Time and Date Settings Manually ……………………………………………… E-36
To change the current time and date settings manually ………………………………………… E-36
To switch between 12-hour and 24-hour timekeeping …………………………………………… E-38
E-11
Hand Home Position Adjustment ……………………………………………………………………… E-39
To adjust home positions …………………………………………………………………………… E-39
Moving the Hands for Easy Viewing of the Digital Dials …………………………………………… E-40
To shift the hands and view digital info …………………………………………………………… E-40
Specifying Altitude, Barometric Pressure, and Temperature Units ……………………………… E-42
To specify altitude, barometric pressure, and temperature units ……………………………… E-42
Taking Barometric Pressure Readings ………………………………………………………………… E-43
To take barometric pressure readings …………………………………………………………… E-43
To show and hide barometric pressure differential ……………………………………………… E-45
To enable or disable the barometric pressure change indicator ……………………………… E-50
To calibrate the pressure sensor …………………………………………………………………… E-51
Taking Direction Readings ……………………………………………………………………………… E-53
To take a direction reading ………………………………………………………………………… E-53
To perform bidirectional calibration ………………………………………………………………… E-57
To perform magnetic declination correction ……………………………………………………… E-58
Using the Altimeter Mode ………………………………………………………………………………… E-62
To specify the altitude reading interval …………………………………………………………… E-63
To take altitude readings …………………………………………………………………………… E-64
To specify a reference altitude value ……………………………………………………………… E-66
To specify the altitude differential measurement range ………………………………………… E-68
To use the altitude differential value ……………………………………………………………… E-69
E-12
Taking Temperature Readings …………………………………………………………………………… E-73
To take temperature readings ……………………………………………………………………… E-73
To calibrate the temperature sensor ……………………………………………………………… E-75
Checking the Current Time in a Different Time Zone ………………………………………………… E-76
To enter the World Time Mode …………………………………………………………………… E-76
To confi gure World Time City and summer time settings ……………………………………… E-77
To swap your Home City and World Time City …………………………………………………… E-79
To access the UTC (Universal Time Coordinated) time zone ………………………………… E-79
Checking the Tide Level and Moon Ages (Tide/Moon) ……………………………………………… E-80
To view the current tide level ……………………………………………………………………… E-80
To view a Moon age ………………………………………………………………………………… E-81
To view tide level and Moon age for a specifi c date and time ………………………………… E-82
To calibrate the high tide time ……………………………………………………………………… E-85
Using the Stopwatch ……………………………………………………………………………………… E-88
To enter the Stopwatch Mode ……………………………………………………………………… E-88
To perform an elapsed time operation …………………………………………………………… E-88
To pause at a split time ……………………………………………………………………………… E-88
To measure two fi nishes …………………………………………………………………………… E-89
E-13
Using the Countdown Timer ……………………………………………………………………………… E-90
To enter the Countdown Timer Mode ……………………………………………………………… E-90
To specify the countdown start time ……………………………………………………………… E-90
To perform a countdown timer operation ………………………………………………………… E-91
To stop the alarm …………………………………………………………………………………… E-91
Using the Alarm …………………………………………………………………………………………… E-92
To enter the Alarm Mode …………………………………………………………………………… E-92
To set an alarm time ………………………………………………………………………………… E-93
To turn an alarm and the Hourly Time Signal on and off………………………………………… E-94
To stop the alarm …………………………………………………………………………………… E-94
To test the alarm …………………………………………………………………………………… E-94
Illumination ………………………………………………………………………………………………… E-95
To turn on illumination manually …………………………………………………………………… E-95
To change the illumination duration ……………………………………………………………… E-96
To enable or disable the auto light switch ………………………………………………………… E-97
Other Settings ……………………………………………………………………………………………… E-99
To turn the button operation tone on or off ……………………………………………………… E-99
To turn Power Saving on or off …………………………………………………………………… E-99
Troubleshooting …………………………………………………………………………………………… E-100
Specifi cations ……………………………………………………………………………………………… E-108
E-14
Charging the Watch
The face of the watch is a solar panel that generates power from light. The generated power charges a
built-in rechargeable battery, which powers watch operations. The watch charges whenever it is exposed
to light.
Charging Guide
Whenever you are not wearing the
watch, leave it in a location where it
is exposed to light.
Best charging performance is
achieved by exposing the watch to
the strongest light available.
When wearing the watch, make sure
that its face is not blocked from light
by the sleeve of your clothing.
The watch may enter a sleep state
(page E-19) if its face is blocked
by your sleeve even only partially.
Warning!
Leaving the watch in bright light for charging can cause it to become quite hot.
Take care when handling the watch to avoid burn injury. The watch can become particularly hot
when exposed to the following conditions for long periods.
On the dashboard of a car parked in direct sunlight
Too close to an incandescent lamp
Under direct sunlight
E-15
Important!
Allowing the watch to become very hot can cause its liquid crystal display to go blank (totally black or
totally white, depending on the watch model). The appearance of the LCD should become normal
again when the watch returns to a lower temperature.
Turn on the watch’s Power Saving function (page E-19) and keep it in an area normally exposed to
bright light when storing it for long periods. This helps to ensure that power does not run down.
Storing the watch for long periods in an area where there is no light or wearing it in such a way that it is
blocked from exposure to light can cause power to run down. Expose the watch to bright light
whenever possible.
Power Levels
In any mode, hold down
B
for at least two seconds. The battery power indicator will appear on the digital
display, and then the watch will enter the Timekeeping Mode.
You can get an idea of the watch’s power level by observing the battery power indicator on the display.
Level Battery Power Indicator Function Status
1
(H)
All functions enabled.
2
(M)
All functions enabled.
Battery power
indicator
Battery power
indicator
Operation Guide 5371
E-16
Level Battery Power Indicator Function Status
3
(L)
Functions below are disabled.
Auto and manual receive
Sensor operation
Moon age
Tide Graph, barometric pressure change
indicator
When the above functions are disabled,
the small hand stays at 9 o’clock.
Illumination
Beeper
Second hand jumps every two seconds.
4
(
CHARGE
)
All hands stopped at 12 o’clock.
All functions disabled.
5 – – –
All hands stopped at 12 o’clock.
All functions disabled and settings return
to their initial factory defaults.
The fl ashing
L
indicator at Level 3 (
L
) tells you that battery power is very low, and that exposure to
bright light for charging is required as soon as possible.
Once the battery reaches Level 2 (
M
) after falling to Level 5, reconfi gure the current time, date, and
other settings.
Display indicators reappear as soon as the battery is charged from Level 5 to Level 2 (
M
).
E-17
Leaving the watch exposed to direct sunlight or some other very strong light source can cause the
battery power indicator to show a reading temporarily that is higher than the actual battery level. The
correct battery level should be indicated after a few minutes.
The current time and all other settings return to their initial factory defaults whenever battery power
drops to Level 5 and when you have the battery replaced.
A dark environment while battery power is at Level 4 will cause the level to drop to Level 5. Expose the
watch to bright light whenever possible.
Low battery alert
When battery power reaches Level 3, the second hand of the watch will
jump at 2-second intervals in the Timekeeping Mode to let you know that
charging is required.
Power Recovery Mode
Performing multiple sensor, illumination, or beeper operations during a short period may cause the
recovery indicator (
RECOVER
) to start fl ashing on the display. This indicates that the watch is in the
power recovery mode. Illumination, alarm, countdown timer alarm, hourly time signal, and sensor
operations will be disabled until battery power recovers.
Battery power will recover in about 15 minutes. At this time, the recovery indicator (
RECOVER
) will stop
ashing. This indicates that the functions listed above are enabled again.
Jumps at two-second
intervals
Jumps at two-second
intervals
E-18
Frequent fl ashing of the recovery indicator (
RECOVER
) indicates that battery power is low. Expose the
watch to bright light as soon as possible.
Even if battery power is at Level 1 (
H
) or Level 2 (
M
), the Digital Compass Mode, Barometer Mode,
Thermometer Mode or Altimeter Mode sensor may be disabled if there is not enough power available
to power it suffi ciently. This is indicated when the recovery indicator (
RECOVER
) are fl ashing.
Frequent fl ashing of the recovery indicator (
RECOVER
) probably means that remaining battery power
is low. Leave the watch in bright light to allow it to charge.
Charging Times
Exposure Level (Brightness)
Daily
Operation
*1
Level Change *2
Level 5 Level 4 Level 3 Level 2 Level 1
Outdoor sunlight (50,000 lux) 8 min. 3 hours 22 hours 6 hours
Sunlight through a window (10,000 lux)
30 min. 7 hours 82 hours 22 hours
Daylight through a window on a
cloudy day (5,000 lux)
48 min. 10 hours 133 hours 36 hours
Indoor fl uorescent lighting (500 lux) 8 hours 118 hours – – – – – –
*1 Approximate amount of exposure time required each day to generate enough power for normal daily
operation.
*2 Approximate amount of exposure time (in hours) required to take power from one level to the next.
The above exposure times all are for reference only. Actual exposure times depend on lighting
conditions.
For details about the operating time and daily operating conditions, see the “Power Supply” section of
the Specifi cations (page E-111).
E-19
Power Saving
When turned on, Power Saving enters a sleep state automatically whenever the watch is left for a certain
period in an area where it is dark. The table below shows how watch functions are affected by Power
Saving.
For information about enabling and disabling power saving, see “To turn Power Saving on or off” (page
E-99).
There actually are two sleep state levels: “display sleep” and “function sleep”.
Elapsed Time in Dark Hands and Display Operation
60 to 70 minutes (display sleep)
Blank display, second hand
stopped.
Except for display and second hand, all
functions enabled.
6 or 7 days (function sleep)
Blank display, all hands
stopped at 12 o’clock.
Except for timekeeping, all functions
disabled.
The watch will not enter a sleep state between 6:00 a.m. and 9:59 p.m. If the watch is already in a sleep
state when 6:00 a.m. arrives, however, it will remain in the sleep state.
The watch will not enter a sleep state while it is in the Stopwatch Mode or Countdown Timer Mode.
The watch will not enter a sleep state while barometric pressure change indicator is enabled (page
E-50).
To recover from the sleep state
Move the watch to a well-lit area, press any button, or angle the watch towards your face for reading (page
E-96).
E-20
Radio Controlled Atomic Timekeeping
This watch receives a time calibration signal and updates its time setting accordingly. However, when
using the watch outside of areas covered by time calibration signals, you will have to adjust the settings
manually as required. See “Confi guring Current Time and Date Settings Manually” (page E-36) for more
information.
This section explains how the watch updates its time settings when the city code selected as the Home
City is in Japan, North America, Europe, or China, and is one that supports time calibration signal
reception.
If your Home City Code setting is this:
The watch can receive the signal from the
transmitter located here:
LONDON (LON), PARIS (PAR), ATHENS (ATH) Anthorn (England), Mainfl ingen (Germany)
HONG KONG (HKG) Shangqiu City (China)
TOKYO (TYO) Fukushima, Fukuoka/Saga (Japan)
NEW YORK (NYC), CHICAGO (CHI), DENVER (DEN), LOS
ANGELES (LAX), ANCHORAGE (ANC), HONOLULU (HNL)
Fort Collins, Colorado (United States)
Important!
The areas covered by
ANC
and
HNL
are quite far from the calibration signal transmitters, so certain
conditions may cause reception problems.
E-21
Approximate Reception Ranges
UK and German Signals
Anthorn
500 kilometers
1,500 kilometers
The Anthorn signal is
receivable within this area
Mainflingen
North American Signal
Japanese Signals Chinese Signal
500 kilometers
Changchun
Beijing
Shangqiu
Shanghai
Chengdu
Hong Kong
1,500 kilometers
2,000 miles
(3,000 kilometers)
600 miles
(1,000 kilometers)
Fort Collins
1,000 kilometers
For the Honolulu and Anchorage time zones, the
signal can be received when reception conditions
are favorable.
Fukuoka/Saga
500 kilometers
Fukushima
E-22
Even when the watch is within range of a transmitter, signal reception may be impossible due to the
effects of geographic contours, structures, weather, the time of year, the time of day, radio interference,
etc. The signal becomes weaker at distances of approximately 500 kilometers, which means that the
infl uence of the conditions listed above becomes even greater.
Signal reception may not be possible at the distances noted below during certain times of the year or
day. Radio interference may also cause problems with reception.
Mainfl ingen (Germany) or Anthorn (England) transmitters: 500 kilometers (310 miles)
Fort Collins (United States) transmitter: 600 miles (1,000 kilometers)
Fukushima or Fukuoka/Saga (Japan) transmitters: 500 kilometers (310 miles)
Shangqiu (China) transmitter: 500 kilometers (310 miles)
As of December 2013, China does not use Daylight Saving Time (DST). If China does go to the Daylight
Saving Time system in the future, some functions of this watch may no longer operate correctly.
To get ready for a receive operation
1. Confi rm that the watch is in the Timekeeping Mode. If it isn’t, use
B
to enter the Timekeeping Mode
(page E-31).
2. The antenna of this watch is located on its 12 o’clock side. Position the watch with 12 o’clock facing
towards a window as shown in the nearby illustration. Make sure there are no metal objects nearby.
Signal reception normally is better at night.
The receive operation takes from two to ten minutes, but
in some cases it can take as long as 20 minutes. Take
care that you do not perform any button operation or
move the watch during this time.
12 o’clock
or
12 o’clock
or
E-23
Signal reception may be diffi cult or even impossible under the conditions described below.
Inside or
among
buildings
Inside a
vehicle
Near
household
appliances,
offi ce
equipment,
or a mobile
phone
Near a
construction
site, airport
Near
high-tension
power lines
Among or
behind
mountains
3. What you should do next depends on whether you are using auto receive or manual receive.
Auto receive: Leave the watch over night in the location you selected in step 2. See “Auto Receive”
below for details.
Manual receive: Perform the operation under “To perform manual receive” on page E-24.
Auto Receive
With auto receive, the watch performs the receive operation each day automatically up to six times (up
to fi ve times for the Chinese calibration signal) between the hours of midnight and 5 a.m. (according to
the Timekeeping Mode time). When any receive operation is successful, none of the other receive
operations for that day are performed.
When a calibration time is reached, the watch will perform the receive operation only if it is in the
Timekeeping Mode. The receive operation is not performed if a calibration time is reached while you
are confi guring settings.
Operation Guide 5371
E-24
You can use the procedure under “To turn auto receive on or off” (page E-27) to enable or disable auto
receive.
To perform manual receive
1. Use
B
to enter the Receive Mode (
R/C
) as shown on page E-30.
2. Hold down
A
for at least two seconds until
RC
ashes and then
RC!
appears on the digital display.
A signal level indicator (L1, L2, or L3, see page E-25) will appear
on the display after reception starts. Do not allow the watch to
move and do not perform any button operation until GET or ERR
appears on the display.
If the receive operation is successful, the reception date and time
appear on the display, along with the GET indicator.
The watch will immediately return to the Timekeeping Mode if you
press any button, or if you do not perform any button operation for
about two or three minutes.
Receive successful
2 seconds
Receive failed
Receiving
Receiving indicator
Receiving
Receiving indicator
E-25
Signal Level Indicator
During calibration signal reception, the signal level indicator displays the
signal level as shown below.
Weak (Unstable) Strong (Stable)
The level indication will change in accordance with reception conditions
while reception is being performed.
As you watch the indicator, keep the watch in a location that best
maintains stable reception.
Even under optimum reception conditions, it can take about 10
seconds for reception to stabilize.
Note that weather, the time of day, surroundings, and other factors all
can affect reception.
E-26
To check the latest signal reception results
Enter the Receive Mode (page E-30).
R/C will be displayed for about one second, and then the date (month and day) and the time of the
last signal reception will alternate on the digital display at two second intervals.
Even if a signal receive operation is successful, RC will be displayed to the left of the date on the
digital display.
Dashes (-.- - and - : - -) alternating in place of the date and time indicate there has been no
successful signal reception yet (since you purchased the watch or had its battery replaced).
2 seconds
To return to the Timekeeping Mode, press
B
.
E-27
To turn auto receive on or off
1. Enter the Receive Mode (page E-30).
R/C will be displayed for about one second, and then the date
(month and day) and the time of the last signal reception will
alternate on the digital display.
Dashes (-.- - and - : - -) alternating in place of the date and time
indicate there has been no successful signal reception yet (since
you purchased the watch or had its battery replaced).
2. Pull out the crown. This will cause the current auto receive status (
ON
or
OFF
) to fl ash on the digital display.
The timekeeping (hour, minute, second) hands will move to 2
o’clock.
Only AUTORC OFF is displayed for cities that do not support time
calibration signal reception. AUTORC ON is not displayed.
3. Rotate the crown to select either auto receive on (
ON
) or auto receive
off (
OFF
).
4. After the setting is the way you want, push the crown back in. This will
return to the screen that was displayed in step 1 of this procedure.
On/Off statusOn/Off status
E-28
Radio-controlled Atomic Timekeeping Precautions
Strong electrostatic charge can result in the wrong time setting.
The receive operation is disabled under any of the following conditions.
– While power is at Level 3 (
L
) or lower (page E-15)
– While the watch is in the power recovery mode (page E-17)
– When the watch is in the function sleep state (“Power Saving”, page E-19)
– While the crown is pulled out
– While barometric pressure change indicator is being measured
– While a countdown timer operation is in progress (page E-90)
A receive operation is cancelled if an alarm sounds while it is being performed.
The watch is designed to update the date and day of the week automatically for the period January 1,
2000 to December 31, 2099. Updating of the date by signal reception will no longer be performed
starting from January 1, 2100.
Even if a receive operation is successful, certain conditions can cause the time setting to be off by up
to one second.
If you are in an area where signal reception is not possible, the watch keeps time with the precision
noted in “Specifi cations”.
The Home City setting reverts to the initial default of
TYO
(Tokyo) whenever the battery power level
drops to Level 5 or when you have the rechargeable battery replaced. If this happens, change the
Home City to the setting you want (page E-34).
E-29
Mode Reference Guide
Your watch has 11 “modes”. The mode you should select depends on what you want to do.
To do this: Enter this mode: See:
View the current time and date in the Home City
Confi gure Home City and daylight saving time (DST) settings
Confi gure time and date settings manually
Enable auto signal reception
Timekeeping Mode E-33
View the barometric pressure at your current location
View a graph of barometric pressure readings
Enable alerts (display and beep) for noteworthy changes in barometric pressure
Barometer Mode E-43
Determine your current bearing or the direction angle from your current location
to a destination
Digital Compass Mode E-53
View the altitude at your current location
Determine the altitude differential between two locations (reference point and
current location)
Altimeter Mode E-62
View the temperature at your current location Thermometer Mode E-73
View the current time in 29 cities (29 time zones) and UTC (Universal Coordinated
Time) time
World Time Mode E-76
View the Tide Graph and Moon age for the currently specifi ed date and time Tide/Moon Data Mode E-80
Use the stopwatch to measure elapsed time Stopwatch Mode E-88
Use the countdown timer Countdown Timer Mode E-90
Set an alarm time Alarm Mode E-92
Perform a manual time calibration signal receive operation
Check whether the last receive operation was successful
Confi gure auto receive settings
Receive Mode E-20
E-30
Selecting a Mode
The illustration below shows which buttons you need to press to navigate between modes.
To return to the Timekeeping Mode from any other mode, hold down
B
for about two seconds.
Countdown
Timer Mode
Alarm Mode
Stopwatch Mode
World Time
Mode
Receive Mode
Tide/Moon Data
Mode
Countdown
Timer Mode
Alarm Mode
Stopwatch Mode
World Time
Mode
Receive Mode
Tide/Moon Data
Mode
E-31
Timekeeping Mode
Digital Compass Mode
Altimeter Mode
Thermometer Mode
Barometer Mode
Sensor Modes
Timekeeping Mode
Digital Compass Mode
Altimeter Mode
Thermometer Mode
Barometer Mode
Sensor Modes
Use the button operations below to navigate between the Timekeeping Mode and sensor (Barometer,
Digital Compass, Altimeter, Thermometer) modes.
Operation Guide 5371
E-32
When you go from the Timekeeping Mode to the sensor modes, the sensor mode that you last used
before returning to the Timekeeping Mode will be entered fi rst.
Whenever you enter a sensor mode, the watch will beep the number of times indicated by the numbers
in the fi gure above. This will let you know what sensor mode you are entering.
To enter a sensor mode from the Tide/Moon Data, Stopwatch, Countdown Timer, Alarm, World Time, or
Receive Mode, fi rst enter the Timekeeping Mode and then press the applicable button.
General Functions (All Modes)
The functions and operations described in this section can be used in all of the modes.
Auto Return Features
The watch automatically returns to the Timekeeping Mode from other modes if the crown is not pulled
out and if no button operation is performed for a preset amount of time.
Mode Name Approximate Elapsed Time
Tide/Moon Data, Alarm, Receive 3 minutes
Barometer, Thermometer 1 hour
Digital Compass 1 minute
Altimeter 1 hour minimum
12 hours maximum
Initial Screens
When you enter the Alarm or World Time Mode, the data you were viewing when you last exited the mode
appears fi rst.
E-33
Timekeeping
Use the Timekeeping Mode (
TIME
) to set and view the current time and date.
Each press of
C
in the Timekeeping Mode will change screen contents as shown below.
Day of the week,
month/day screen
Barometric pressure graph,
date (month/day) screen
Time (hour, minute,
second) screen
World Time screenMoon age screen
Barometric
pressure graph
Day of week
Hour : MinutesMoon age
Month Day
Hour : Minutes Second
Month Day
Holding down
C
for at least two seconds while any screen is displayed will toggle the barometric
pressure change indicator between ON and OFF.
When ON, the barometric pressure graph is displayed along with the
BARO
indicator.
For information about how to check for signifi cant barometric pressure changes, refer to “Barometric
Pressure Change Indications” (page E-49).
E-34
Confi guring Home City Settings
There are two Home City settings: actually selecting the Home City and selecting either standard time or
daylight saving time (DST).
To confi gure Home City and summer time settings
1. In the Timekeeping Mode, pull out the crown.
CITY will fl ash on the digital display indicating that the Home City
setting can be changed.
2. Rotate the crown to move the second hand to the city code of the city
you want you use as your Home City.
For details about city codes, see the “City Code Table” at the back
of this manual.
3. Press
B
to display the DST setting screen.
4. Rotate the crown away from you to cycle through the DST settings as
shown below.
Auto DST (AUTO) DST off (OFF)
DST on (
ON
)
The displayed DST setting will not change if you rotate the crown
towards you.
After you change the Home City and/or DST setting, the hour
and minute hands will automatically move to the appropriate time
setting. The time shown on the digital display will also change
accordingly.
City code
Second Hand
City code
Second Hand
E-35
The Auto DST (AUTO) setting will be available only when a city code that supports time calibration
signal reception (page E-20) is selected as the Home City. While Auto DST is selected the DST
setting will be changed automatically in accordance with time calibration signal data.
Note that you cannot switch between standard time and daylight saving time (DST) while UTC is
selected as your Home City.
5. After the settings are the way you want, push the crown back in.
Daylight Saving Time is turned on when the DST indicator is on the display.
Note
After you specify a city code, the watch will use UTC* offsets in the World Time Mode to calculate
the current time for other time zones based on the current time in your Home City.
* Coordinated Universal Time, the world-wide scientifi c standard of timekeeping.
The reference point for UTC is Greenwich, England.
Selecting some city codes automatically makes it possible for the watch to receive the time
calibration signal for the corresponding area. See page E-20 for details.
E-36
Confi guring Current Time and Date Settings Manually
You can confi gure current time and date settings manually when the watch is unable to receive a time
calibration signal.
To change the current time and date settings manually
1. In the Timekeeping Mode, pull out the crown. This will cause
CITY
to
ash on the digital display.
2. Press
C
.
This will cause HOUR-MIN to fl ash on the digital display.
The second hand will point to either A (a.m.) or P (p.m.)
This is the time setting mode.
In the following steps, each press of
B
cycles between settings
as shown below.
Home City/DST
Hour, minute
Month, day
Hour
Year
City codeCity code
E-37
3. Rotate the crown to change the minute setting.
You can also use HS1 and HS2 high-speed movement (page E-6) to move the hands forward or
back at high speed.
The hour hand will move in accordance with minute hand movement.
To set the hour hand separately, go to step 4 of this procedure.
4. Press
B
.
This will cause HOUR to fl ash on the digital display.
5. Rotate the crown to change the hour setting.
You can also use HS1 and HS2 high-speed movement (page E-6) to move the hands forward or
back at high speed.
6. Press
B
.
This causes the currently set year, month, and day to appear on
the digital display, with the year setting fl ashing.
7. Rotate the crown to adjust the year setting.
You can also use HS1 high-speed movement (page E-6) to change
this setting.
8. Press
B
.
This causes the currently set date (month, day) setting to fl ash on
the display.
9. Rotate the crown to adjust the month and day setting.
You can also use HS1 high-speed movement (page E-6) to change this setting.
Pressing
B
will return to the hour and minute setting screen.
10. After the settings are the way you want, push the crown back in.
This will cause timekeeping to start from 0 seconds.
E-38
Note
For information about selecting a Home City and confi guring the DST setting, see “Con guring
Home City Settings” (page E-34).
While 12-hour timekeeping is in use, P (p.m.) is displayed from noon to midnight (11:59 p.m.) A (a.m.)
is displayed from midnight to noon (11:59 a.m.) These indicators are not displayed while 24-hour
timekeeping (displays times from 00:00 to 23:59) is being used.
The watch’s built-in full automatic calendar makes allowances for different month lengths and leap
years. Once you set the date, there should be no reason to change it except after you have the
watch’s rechargeable battery replaced or after power drops to Level 5 (page E-15).
The day of the week changes automatically when the date changes.
Refer to the pages shown below for more information on Timekeeping Mode settings.
- Button operation tone on/off: “To turn the button operation tone on or off” (page E-99)
- Illumination duration setting: “To change the illumination duration” (page E-96)
- Enabling and disabling power saving: “To turn Power Saving on or off” (page E-99)
To switch between 12-hour and 24-hour timekeeping
1. Pull out the crown.
2. Press
B
ve times.
This causes the current timekeeping setting (12H or 24H) to fl ash
on the digital display.
3. Rotate the crown to select either 12-hour (
12H
) or 24-hour (
24H
)
timekeeping.
4. After the setting is the way you want, push the crown back in.
E-39
Hand Home Position Adjustment
If the watch is exposed to strong magnetism or impact, its hands can go out of alignment with the time on
the digital display. This can result in incorrect time indication even though a time calibration signal is being
received. Your watch has an auto hand position correction feature that normally adjusts the hands. Should
you notice that the hand positions are not correct, perform the operation below to correct them manually.
To adjust home positions
1. In the Timekeeping Mode, pull out the crown.
2. Hold down
A
for at least fi ve seconds until
HAND SET
ashes and
then
HAND ADJ
appears on the digital display.
This will start home position adjustment, which causes all of the
watch hands to move to 12 o’clock.
After the hands stop moving, will appear on the digital
display.
Important!
Before performing step 3, below, make sure that all hands have
returned to the 12 o’clock position. Pushing the crown back in
while any hand is not at the 12 o’clock position will not perform
home position adjustment.
3. Push the crown back in.
This will cause all of the hands (small hand, hour hand, minute
hand, second hand) to return to their normal positions.
Note
After performing home position adjustment, enter the Timekeeping Mode and check to make sure that the
analog hands and the display indicate the same time. If they do not, perform home position adjustment
again.
Wait until all of the hands
move to 12 o'clock.
Wait until all of the hands
move to 12 o'clock.
Operation Guide 5371
E-40
Moving the Hands for Easy Viewing of the Digital Dials
You can use the procedure below to move the analog hands in order to view the dial and the digital
display better.
Note
The analog hands will not move while battery power is low.
To shift the hands and view digital info
While holding down
L
, press
B
.
This will cause the timekeeping (hours, minutes, seconds) hands to move to 2 o’clock.
To return the hands to their normal positions, press
A
,
B
, or
C
.
E-41
Note
The hands will also return to their normal positions if you do not perform any operation for about 10
seconds.
If the hands have moved to 2 o’clock because you pulled out the crown,* they will return to their normal
positions when you push the crown back in.
In this case, the hands will return to normal timekeeping when you push the crown back in.
* The hands will not move to 2 o’clock if you pull out the crown while confi guring the city code setting
(pages E-34, E-77) or the summer time setting (pages E-34, E-77), or while manually confi guring
time and date settings (page E-36).
Auto Hand Shift
If the hour hand and/or minute hand is over the digital display when a displayed barometric pressure,
altitude, or temperature reading is updated, the hand(s) will shift automatically (to 4 o’clock or 8 o’clock)
and provide a better view of the information on the display.
The hands will return to their normal position after about three seconds.
E-42
Specifying Altitude, Barometric Pressure, and Temperature Units
Use the procedure below to specify the altitude, barometric pressure, and temperature units to be used in
the Altimeter Mode, Barometer Mode and the Thermometer Mode.
Important!
When
TYO
(Tokyo) is selected as the Home City, the altitude unit is set automatically to meters (
m
), the
barometric pressure unit to hectopascals (
hPa
), and the temperature unit to Celsius (
°C
). These
settings cannot be changed.
To specify altitude, barometric pressure, and temperature units
1. Make sure the watch is in the mode for the type of unit you want to
specify (Altimeter, Barometer, or Thermometer Mode).
For information about changing modes, see “Selecting a Mode”
(page E-30).
2. Pull out the crown.
The timekeeping (hour, minute, second) hands will move to
2 o’clock.
3. Press
B
as many times as necessary until
UNIT
appear on the digital
display.
For altitude, press
B
three times. For barometric pressure and
temperature, press
B
once.
4. Rotate the crown to change the unit setting.
5. After the settings are the way you want, push the crown back in.
E-43
Taking Barometric Pressure Readings
This watch uses a pressure sensor to measure air pressure (barometric pressure).
To take barometric pressure readings
In the Timekeeping Mode or any sensor mode, press
A
a number of
times until
BARO
(Barometer Mode) appears on the digital display.
In a non-sensor mode, hold down
B
for about two seconds to enter
the Timekeeping Mode. Next, perform the above step.
About one second after entering the Barometer Mode (
BARO
), the fi rst
barometric pressure reading will be displayed.
Readings are continuously taken for about one hour: every fi ve
seconds for the fi rst three minutes and then every two minutes for the
remainder of the hour.
Pressing
C
or
L
, or rotating the crown while a reading operation is in
progress will extend the operation for approximately one hour from
point the button was pressed or the crown was rotated.
The watch will return to the Timekeeping Mode after the reading
operation is complete (about one hour).
Pressing
B
while a reading operation is in progress will stop the
operation and enter the Timekeeping Mode.
Barometric
pressure graph
Barometric
pressure
Barometric
pressure graph
Barometric
pressure
E-44
Note
When you enter the Barometer Mode, the second hand may indicate seconds (of the current time) or
the barometric pressure differential (page E-45). The initial second hand function will be the same as
what was selected the last time you took a barometric pressure reading. To toggle between the two
second hand functions (indicating seconds or indicating the barometric pressure differential) press
C
.
Barometric Pressure
Barometric pressure is displayed in units of 1 hPa (or 0.05 inHg).
The displayed barometric pressure value changes to
- - -
if a measured barometric pressure falls outside
the range of 260 hPa to 1,100 hPa (7.65 inHg to 32.45 inHg). The barometric pressure value will reappear
as soon as the measured barometric pressure is within the allowable range.
Display Units
You can select either hectopascals (hPa) or inchesHg (inHg) as the display unit for the measured
barometric pressure. See “To specify altitude, barometric pressure, and temperature units” (page E-42).
E-45
Checking Barometric Pressure Changes and Trends
Your watch provides the three methods below for checking barometric pressure changes and trends.
Checking the latest change in barometric pressure (Barometric pressure differential pointer described
below)
Checking barometric pressure changes for the past 20 hours (Barometric Pressure Graph, page E-47)
Checking for signifi cant barometric pressure changes (Barometric Pressure Change Indicator, page
E-49)
Barometric Pressure Differential Pointer
Your watch automatically takes barometric pressure measurements every two hours (at the 30 minute
mark of each even numbered hour), regardless of the mode it is in.
The second hand of the watch indicates the difference between the current barometric reading and
previous automatic reading, within the range of ±10hPa (1hPa unit). This keeps you informed about
current barometric pressure changes in your area.
To show and hide barometric pressure differential
1. In the Timekeeping Mode or any sensor mode, press
A
a number of times until
BARO
(Barometer
Mode) appears on the digital display.
In a non-sensor mode, hold down
B
for about two seconds to enter the Timekeeping Mode. Next,
perform the above step.
2. Press
C
.
Note
Press
C
to toggle the second hand between its two functions (indicating seconds or indicating the
barometric pressure differential).
E-46
Reading Barometric Pressure Differential Pointer
Pressure differential is indicated in the
range of ±10 hPa (0.3 inHg), in 1 hPa (0.03
inHg) units.
The nearby screen shot, for example,
shows what the second hand would
indicate when the calculated pressure
differential is approximately – 5 hPa
(approximately – 0.15 inHg).
The second hand will point to
+ OVER
or
– UNDER
if the barometric pressure
differential is outside the allowable range
of the scale.
The second hand will move to 9 o’clock
if a sensor reading could not be taken
for some reason or if the reading is
outside the allowable range.
Barometric pressure is calculated and
displayed using hPa as the standard.
The barometric pressure differential also
can be read in inHg units as shown in
the illustration (1 hPa
=
0.03 inHg).
Barometric
pressure
differential
pointer
inHg values
hPa values
Current pressure
greater than most
recent measured
pressure
Current pressure
less than most
recent measured
pressure
−0.15
−5
−10
−0.3
Barometric
pressure
differential
pointer
inHg values
hPa values
Current pressure
greater than most
recent measured
pressure
Current pressure
less than most
recent measured
pressure
−0.15
−5
−10
−0.3
E-47
Barometric Pressure Graph
Your watch automatically takes barometric pressure measurements every
two hours (at the 30 minute mark of each even numbered hour), regardless of
the mode it is in.
While the watch is in the Barometer Mode or Timekeeping Mode, the digital
display shows a graph of pressure change for the past 20 hours (10
readings). By monitoring these changes you can predict the weather with
reasonable accuracy.
To display the barometric pressure graph in the Timekeeping Mode, press
C
a number of times to cycle through digital display screens until it
appears (page E-33).
Reading the Barometric Pressure Graph
The barometric pressure graph shows a chronological history of pressure readings.
The vertical axis of the graph represents barometric pressure, with each
dot standing for the relative difference between its reading and that of the
dots next to it. Each dot represents 1 hPa.
The latest automatic reading is indicated by the rightmost segment in the
graph.
The following shows how to interpret the data that appears on the barometric pressure graph.
Rising barometric pressure indicates that upcoming weather will improve.
Falling barometric pressure indicates that upcoming weather will deteriorate.
Barometric pressure
graph
Barometric pressure
graph
Barometric
pressure
Time
Barometric
pressure
Time
Operation Guide 5371
E-64
To take altitude readings
In the Timekeeping Mode or any sensor mode, press
A
a number of
times until
ALTI
(Altimeter Mode) appears on the digital display.
In a non-sensor mode, hold down
B
for about two seconds to enter
the Timekeeping Mode. Next, perform the above step.
After you enter the Altimeter Mode (
ALTI
), the watch will start taking
altitude readings.
The current altitude value is displayed in units of 1 meter (5 feet).
For information about the measurement interval, see page E-62.
Note
When you enter the Altimeter Mode, the second hand may indicate seconds (of the current time) or the
altitude differential (page E-67). The initial second hand function will be the same as what was selected
the last time you took an altitude reading. To toggle between the two second hand functions (indicating
seconds or indicating the altitude differential) press
C
.
Pressing
C
or
L
, or rotating the crown while a reading operation is in progress will extend the
operation for approximately one hour or 12 hours (depending on the current measurement time and
interval setting) from point the button was pressed or the crown was rotated.
The watch will return to the Timekeeping Mode at the end of the applicable measurement time (one
hour or 12 hours).
Pressing
B
while a reading operation is in progress will stop the operation and return to the
Timekeeping Mode.
The measurement range for altitude is –700 to 10,000 meters (–2,300 to 32,800 feet).
The displayed altitude value changes to
- - - -
if an altitude reading falls outside the measurement
range. An altitude value will reappear as soon as the altitude reading is within the allowable range.
Altitude Tendency Graph
Altitude
Altitude Tendency Graph
Altitude
E-65
You can change the unit for displayed altitude values to either meters (m) or feet (ft). See “To specify
altitude, barometric pressure, and temperature units” (page E-42).
The altitude tendency graph shows changes in altitude over the past 6 readings while readings are
being taken.
50 meters
(10 meters for
each block )
6 readings
ago
Current
reading
Using Reference Altitude Values
To minimize the chance of reading error, you should update the reference altitude value before setting off
on a trek or any other activity where you plan to take altitude readings. While mountain climbing, it is
highly recommended that you check a map, local altitude indications, or some other source for your
current correct altitude and regularly update the reference altitude value with the latest information.
Reading error can be caused by changes in barometric pressure, and by temperature changes due to
change in barometric pressure and/or elevation.
Though altitude readings can be taken without setting a reference altitude, doing so may produce
readings that are very different from altitudes indicated by other altitude markers and indications.
Before performing the procedure below, look up the altitude of your current location on a map, the
Internet, etc.
E-66
To specify a reference altitude value
1. In the Altimeter Mode, pull out the crown.
This will cause the current altitude reading value to fl ash on the
digital display.
The timekeeping (hour, minute, second) hands will move to 2
o’clock.
2. Rotate the crown to change the altitude value in one-meter (fi ve-foot)
increments.
You can also use HS1 high-speed movement (page E-6) to change
this setting.
Change the reference altitude value to an accurate altitude reading
that you get from a map or other source.
You can set the reference altitude value within the range of –3,000
to 10,000 meters (–9,840 to 32,800 feet).
To return to the OFF setting so no reference altitude value is
applied to readings, press
A
and
C
at the same time.
3. After the setting is the way you want, push the crown back in to exit the
setting screen.
E-67
Advanced Altimeter Mode Operations
Use the information in this section to obtain more accurate altimeter readings, especially while mountain
climbing or trekking.
Using an Altitude Differential Value
If you specify an altitude differential start point, the second hand of the
watch will indicate the difference between the current altitude and the
altitude differential start point. The displayed altitude differential value is
updated each time the watch obtains a new altitude reading value.
Depending on the currently selected display range, the allowable
range for the altitude differential value is 100 meters to –100 meters
(100 meters = 328 feet), or 1,000 meters to –1,000 meters (1,000
meters = 3,280 feet).
If a reading value is outside the allowable range either
+ OVER
or
– UNDER
appears on the digital display (page E-70).
The second hand will move to 9 o’clock if a sensor reading could not
be taken for some reason or if the reading is outside the allowable
range.
See “Using the Altitude Differential Value While Mountain Climbing or
Hiking” (page E-68) for some real-life examples of how to use this
feature.
Altitude differentialAltitude differential
E-68
Specifying the Altitude Differential Measurement Range
You can use the procedure below to select either ±100 meters or ±1,000
meters as the altitude differential measurement range.
Relative Altitude Measurement Range Display Unit
±100 meters (±328 feet) 5 meters (16 feet)
±1,000 meters (±3,280 feet) 50 meters (164 feet)
To specify the altitude differential measurement range
1. In the Altimeter Mode, pull out the crown.
This will cause the current altitude reading value to appear.
The timekeeping (hour, minute, second) hands will move to 2
o’clock.
2. Press
B
twice.
This will cause DIFF to appear on the digital display, along with the
ashing current altitude differential measurement range setting.
3. Rotate the crown to select either 100 meters (
100m
) or 1,000 meters
(
1000m
) as the altitude differential measurement range.
4. After the setting is the way you want, push the crown back in to exit the
setting screen.
Using the Altitude Differential Value While Mountain Climbing or Hiking
After you specify the altitude differential start point while mountain climbing or hiking, you can easily
measure the change in the altitude between that point and other points along the way.
Altitude differential rangeAltitude differential range
E-69
To use the altitude differential value
1. Use the contour lines on your map to determine the difference in
altitude between your current location and your destination.
Knowing the difference in altitude helps you determine your
current location and how much further you need to go to reach
your destination.
2. In the Altimeter Mode, hold down
C
for at least two seconds to specify
your current location as the altitude differential start point.
DIFF RESET and then RESET will appear on the digital display,
and then the second hand will move to ±0 (±0m) to indicate the
altitude differential.
3. While comparing the altitude difference you determined on the map
and the watch’s altitude differential value, advance towards your
destination.
If the map shows that the difference in altitude between your
location and your destination is +80 meters for example, you know
you will be nearing your destination when the displayed altitude
differential value shows +80 meters.
Current
location
Destination
altitude
Current
location
Destination
altitude
Altitude Differential (Reference
location, so ±0 m is indicated.)
Current altitude
Altitude Differential (Reference
location, so ±0 m is indicated.)
Current altitude
E-70
The altitude differential with the reference location is indicated by the second hand as shown in the nearby
illustration.
When
±100m
is selected for the altitude
differential measurement range, the
+ OVER
indicator appears any time the
differential is greater than +100 meters
(+328 feet). The
− UNDER
indicator
appears any time the differential is
greater than −100 meters (−328 feet). If
either of these indicators appears,
change the range setting to
±1000m
.
When
±1000m
is selected for the
altitude differential measurement range,
the
+ OVER
indicator appears any time
the differential is greater than +1,000
meters (+3,280 feet). The
− UNDER
indicator appears any time the
differential is greater than −1,000
meters (−3,280 feet).
The second hand will move to 9 o’clock
if a reading is outside the altimeter
measurement range (−700 to +10,000
meters (–2,300 to 32,800 feet)), or if a
reading error occurs.
To toggle between the altitude
differential and current time seconds
count on the digital display, press
C
.
Unit: 50m (164ft)
Unit:
Meters
Unit: 5m (16ft)
−500m (−1,640ft)
−50m (−164ft)
−100m (−328ft)
−1,000m (−3,280ft)
1,000m (3,280ft)
500m (1,640ft)
100m (328ft)
Example:
Altitude
differential
of −30
(300)
meters
Indication range:
±100 (1,000) meters
50m (164ft)
00
Unit: 50m (164ft)
Unit:
Meters
Unit: 5m (16ft)
−500m (−1,640ft)
−50m (−164ft)
−100m (−328ft)
−1,000m (−3,280ft)
1,000m (3,280ft)
500m (1,640ft)
100m (328ft)
Example:
Altitude
differential
of −30
(300)
meters
Indication range:
±100 (1,000) meters
50m (164ft)
00
E-71
How does the altimeter work?
Generally, air pressure decreases as altitude increases. This watch bases its altitude reading on
International Standard Atmosphere (ISA) values stipulated by the International Civil Aviation Organization
(ICAO). These values defi ne relationships between altitude and air pressure.
Note that the following conditions will prevent you from obtaining accurate readings:
When air pressure changes because of changes in the weather
Extreme temperature changes
When the watch itself is subjected to strong impact
There are two standard methods of expressing altitude: absolute altitude, which expresses an absolute
height above sea level, and relative altitude, which expresses the difference between the altitudes of two
different places. This watch expresses altitudes as relative altitude.
Height of building 130 m
(relative altitude)
Rooftop at an altitude of
230 m above sea level
(absolute altitude)
Sea Level
Regular calibration of the watch in accordance with values provided by local altitude (elevation) indications
is recommended before taking readings in order to maximize reading accuracy (page E-65).
Operation Guide 5371
E-72
Altimeter Precautions
This watch estimates altitude based on air pressure. This means that altitude readings for the same
location may vary if air pressure changes.
Do not use this watch for altitude reading or perform button operations while sky diving, hang gliding,
or paragliding, while riding a gyrocopter, glider, or any other aircraft, or while engaging in any other
activity where there is the chance of sudden altitude changes.
Do not use this watch for measuring altitude in applications that demand professional or industrial level
precision.
Remember that the air inside of a commercial aircraft is pressurized. Because of this, the readings
produced by this watch will not match the altitude readings announced or indicated by the fl ight crew.
The Effect of Temperature on Altitude Readings
For the more accurate altitude readings, leaving the watch on your wrist is recommended in order to
maintain the watch at a constant temperature.
When taking altitude readings, keep the watch at as stable a temperature as possible. Changes in
temperature can affect altitude readings.
E-73
Taking Temperature Readings
This watch uses a temperature sensor to measure temperature.
To take temperature readings
In the Timekeeping Mode or any sensor mode, press
A
a number of
times until
TEMP
(Thermometer Mode) appears on the digital display.
In a non-sensor mode, hold down
B
for about two seconds to enter
the Timekeeping Mode. Next, perform the above step.
About one second after entering the Thermometer Mode (
TEMP
), the
rst temperature reading will be displayed.
Readings are continuously taken for about one hour: every fi ve
seconds for the fi rst three minutes and then every two minutes for the
remainder of the hour.
Pressing
C
or
L
, or rotating the crown while a reading operation is in
progress will extend the operation for approximately one hour from
point the button was pressed or the crown was rotated.
The watch will return to the Timekeeping Mode after the reading
operation is complete (about one hour).
Pressing
B
while a reading operation is in progress will stop the
operation and enter the Timekeeping Mode.
TemperatureTemperature
E-74
Temperature
Temperature is displayed in units of 0.1°C (or 0.2°F).
The displayed temperature value changes to
- -.-
°C (or °F) if a measured temperature falls outside the
range of –10.0°C to 60.0°C (14.0°F to 140.0°F). The temperature value will reappear as soon as the
measured temperature is within the allowable range.
Display Units
You can select Celsius (°C) or Fahrenheit (°F) as the display unit for the measured temperature value.
See “To specify altitude, barometric pressure, and temperature units” (page E-42).
Temperature Sensor Calibration
The temperature sensor built into the watch are calibrated at the factory and normally require no further
adjustment. If you notice serious errors in the temperature readings produced by the watch, you can
calibrate the sensor to correct the errors.
Important!
Incorrectly calibrating the temperature sensor can result in incorrect readings.
Carefully read the following before doing anything.
Compare the readings produced by the watch with those of another reliable and accurate thermometer.
– If adjustment is required, remove the watch from your wrist and wait for 20 or 30 minutes to give the
temperature of the watch time to stabilize.
E-75
To calibrate the temperature sensor
1. Take a reading with another measurement device to determine the
exact current temperature.
2. Use
A
to enter the Thermometer Mode (
TEMP
), as shown on page
E-31.
3. Pull out the crown. This will cause the current temperature reading
value to fl ash on the digital display.
The timekeeping (hour, minute, second) hands will move to
2 o’clock.
4. Rotate the crown to adjust the temperature value.
You can also use HS1 high-speed movement (page E-6) to change
this setting.
The calibration unit is 0.1°C (0.2°F).
To return the setting to
OFF
(uncalibrated), press
A
and
C
at the
same time.
5. After you complete calibration, push the crown back in.
Thermometer Precautions
Temperature readings are affected by your body temperature, direct sunlight, and moisture. To achieve
a more accurate temperature reading, remove the watch from your wrist, place it in a well ventilated
location out of direct sunlight, and wipe all moisture from the case. It takes approximately 20 to 30
minutes for the case of the watch to reach the surrounding temperature.
E-76
Checking the Current Time in a Different Time Zone
You can use the World Time Mode to display the current time in any one for 29 time zones (29 cities)
around the world, and in the UTC (Universal Time Coordinated) time zone. The city that is currently
selected in the World Time Mode is called the “World Time City”.
Your watch includes functions for quickly swapping your Home City and World Time City settings, and
for one-touch access to the UTC time zone.
To enter the World Time Mode
Use
B
to select the World Time Mode (
WT
) as shown on page E-30.
This causes
WT
to appear on the digital display. After one second, the
hour and minute hands move to indicate the time in the current World
Time City. The second hand points to the currently selected World Time
City for three seconds, and then returns to indicating the seconds.
The digital display shows the current time in the Home City.
To check whether the indicated World Time City time is a.m. or p.m.,
press
A
. This will cause the second hand to move to
A
(a.m.) or
P
(p.m.) The second hand will return to regular timekeeping after about
three seconds.
Pressing
C
will cause the second hand to move to the currently
selected World Time City city code. The second hand will return to
regular timekeeping after about three seconds.
Currently selected
Word Time City
Current timekeeping
Mode time
Current time in the currently
selected World Time City
Currently selected
Word Time City
Current timekeeping
Mode time
Current time in the currently
selected World Time City
E-77
To confi gure World Time City and summer time settings
1. In the World Time Mode, pull out the crown.
This will cause CITY to fl ash on the digital display.
The currently selected World Time City will be indicated by the
second hand.
2. Rotate the crown to move the second hand to the City Code you want
to select.
For details about city codes, see the “City Code Table” at the back
of this manual.
3. Press
B
.
This will cause the current DST setting (DST ON or DST OFF) to
ash on the display.
4. Rotate the crown to select either on (
DST ON
) or off (
DST OFF
) for the
DST setting.
DST is shown on the digital display while DST is turned on.
5. After the settings are the way you want, push the crown back in.
Note that you cannot switch between standard time/daylight
saving time (DST) while UTC is selected as the World Time City.
Note that the standard time/daylight saving time (DST) setting
affects only the currently selected time zone. Other time zones are
not affected.
DST indicatorDST indicator
E-78
Swapping the Home City and World Time City
You can use the procedure below to swap your World Time City (whose time is indicated by the hands)
with your Home Time City (whose time is indicated by the digital display).
This function comes in handy for those who often travel between two different time zones.
The following example shows what happens when the Home City and World Time City are swapped while
the Home City originally is
TOKYO
(
TYO
) and the World Time City is
NEW YORK
(
NYC
).
Home City World Time City
Before swapping
Tokyo
10:08 p.m
(Standard time)
New York
9:08 a.m.
(Daylight saving time)
After swapping
New York
9:08 a.m.
(Daylight saving time)
Tokyo
10:08 p.m.
(Standard time)
You need to confi gure starting Home City and World Time City settings before performing the
procedure below.
Home City and summer time settings (page E-34)
World Time City and summer time settings (page E-77)
E-79
To swap your Home City and World Time City
In the World Time Mode, hold down
C
for at least three seconds.
After
CITY
ashes on the digital display, the watch will swap the Home City and World Time City
settings and the second hand will move to the new World Time City. After that, the times indicated by
the hand and on the digital display will be swapped with each other.
The second hand will return to regular timekeeping after about three seconds.
In the above example, the hands show current time in Tokyo (TYO), while the digital display shows
the current time in New York (NYC).
World Time City
(TYO) time
Current World
Time City
New World Time City
To access the UTC (Universal Time Coordinated) time zone
In the World Time Mode, hold down
A
for at least three seconds.
After UTC ashes on the digital display, the second hand will move to
UTC. After that, the hour hand and minute hand will move to the
current time in the UTC zone.
The second hand will return to regular timekeeping after about three
seconds.
Operation Guide 5371
E-88
Using the Stopwatch
The stopwatch measures elapsed time, split times, and two fi nishes.
To enter the Stopwatch Mode
Use
B
to select the Stopwatch Mode (
STW
) as shown on page E-30.
To perform an elapsed time operation
A
A
A A
C
Start Stop (Resume) (Stop) Reset
To pause at a split time
A
C
C A
C
Start Split
(
SP
appears on
the digital
display.)
Split release Stop Reset
Current time
Hours
Seconds
Minutes
1/100 secondCurrent time
Hours
Seconds
Minutes
1/100 second
E-89
To measure two fi nishes
A
C
A C
C
Start Split
First runner fi nishes.
(
SP
appears on the
digital display.)
Display time of fi rst
runner
Stop
Second runner
nishes.
Split release
Display time of
second runner
Reset
Note
The Stopwatch Mode can indicate elapsed time up to 23 hours, 59 minutes, 59.99 seconds.
Once started, stopwatch timing continues until you press
A
to stop it, even if you exit the Stopwatch
Mode to another mode and even if timing reaches the stopwatch limit defi ned above.
Exiting the Stopwatch Mode while a split time is frozen on the display clears the split time.
E-90
Using the Countdown Timer
The countdown timer can be confi gured to start at a preset time, and sound an alarm when the end of the
countdown is reached.
To enter the Countdown Timer Mode
Use
B
to select the Countdown Timer Mode (
TIMER
) as shown on page E-30.
About one second after
TIMER
appears on the display, the display will change to show the countdown
time hours.
To specify the countdown start time
1. In the Countdown Timer Mode, pull out the crown.
This will cause the current start time minutes digits to fl ash on the
digital display.
The timekeeping (hour, minute, second) hands will move to 2
o’clock.
2. Rotate the crown to adjust the minutes setting.
You can also use HS1 high-speed movement (page E-6) to change
this setting.
To set a starting countdown time of 60 minutes, set 00’00.
3. After the setting is the way you want, push the crown back in.
Countdown time
(Minutes, seconds)
Current time
Countdown time
(Minutes, seconds)
Current time
E-91
To perform a countdown timer operation
A
A
A A
C
Start Stop (Resume) (Stop) Reset
Before starting a countdown timer operation, check to make sure that a countdown operation is not in
progress (indicated by the seconds counting down). If it is, press
A
to stop it and then
C
to reset to
the countdown start time.
An alarm sounds for ten seconds when the end of the countdown is reached. This alarm will sound in
all modes. The countdown time is reset to its starting value automatically when the alarm sounds.
Pulling out the crown while a timer operation is in progress will stop the operation and reset the time to
the start time.
To stop the alarm
Press any button.
E-92
Using the Alarm
You can set fi ve independent daily alarms. When an alarm is turned on, an alarm will sound for about 10
seconds each day when the time in the Timekeeping Mode reaches the preset alarm time. This is true
even if the watch is not in the Timekeeping Mode.
You can also turn on an Hourly Time Signal, which will cause the watch to beep twice every hour on the
hour.
To enter the Alarm Mode
Use
B
to select the Alarm Mode (
ALARM
) as shown on page E-30.
About one second after
ALARM
appears on the display, the display will change to show an alarm
name (
AL1
through
AL5
) or the
SIG
indicator. The alarm name indicates an alarm screen.
SIG
is
shown when the Hourly Time Signal screen is on the display.
When you enter the Alarm Mode, the data you were viewing when you last exited the mode appears
rst.
Alarm name (AL- or SIG)
Alarm time (Hour : Minutes)
Hourly Time Signal screen
Alarm 1 screen
E-93
To set an alarm time
1. In the Alarm Mode, use
A
to scroll through the alarm screens until the
one whose time you want to set is displayed.
AL1 AL2 AL3
SIG* AL5 AL4
* There is no time setting for the hourly time signal.
2. Pull out the crown.
This will cause the hour and minute digits of the alarm time to fl ash.
The timekeeping (hour, minute, second) hands will move to 2 o’clock.
3. Rotate the crown to adjust the minute setting.
You can also use HS1 high-speed movement (page E-6) to change this setting.
Hour setting will change in accordance with minute setting changes. To change the hour setting
separately, go to step 4 of this procedure.
4. Press
B
.
5. Rotate the crown to adjust the hour setting.
You can also use HS1 high-speed movement (page E-6) to change this setting.
If you are using 12-hour timekeeping, the P (p.m.) and A (a.m.) indicators will also appear on the
display.
6. After the settings are the way you want, push the crown back in.
Setting an alarm time causes that alarm to turn on automatically.
E-94
To turn an alarm and the Hourly Time Signal on and off
1. In the Alarm Mode, use
A
to select an alarm or the Hourly Time Signal.
2. When the alarm or the Hourly Time Signal you want is selected, press
C
to turn it on and off.
The alarm on indicator (when any alarm is on), and the Hourly Time Signal on indicator (when the Hourly
Time Signal is on) are shown on the display in all modes.
Hourly time signal on indicator
Alarm on indicator
To stop the alarm
Press any button.
To test the alarm
In the Alarm Mode, hold down
A
to sound the alarm tone.
E-95
Illumination
The display of the watch is illuminated for easy reading in the dark.
The watch’s auto light switch turns on illumination automatically when you angle the watch towards your
face.
The auto light switch must be turned on (page E-97) for it to operate.
To turn on illumination manually
Press
L
in any mode to illuminate the display.
You can use the procedure below to select either 1.5 seconds or three
seconds as the illumination duration. When you press
L
, the display
will remain illuminated for about 1.5 seconds or three seconds,
depending on the current illumination duration setting.
The above operation turns on illumination regardless of the current
auto light switch setting.
Illumination will turn off automatically if an alarm starts to sound or if
you perform a crown operation.
Illumination will not turn on if a calibration signal receive operation or
hand movement operation is in progress. Also, illumination may not
turn on while a sensor is taking a reading.
Operation Guide 5371
E-104
Charging
The watch does not resume operation after I expose it to light.
This can happen after the power level drops to Level 5 (page E-15). Keep the watch exposed to light until
it recharges suffi ciently.
RECOVER is fl ashing on the digital display.
The watch is in the charge recovery mode. Wait until the recovery process is complete (about 15 minutes).
The watch will recover more quickly if you place it in a brightly lit location.
Note
Performing repeated illumination and/or sensor reading operations over a short time period can cause
a sudden drop in watch’s charge. This will cause the watch to enter the charge recover mode. The
watch is in the charge recovery mode when
RECOVER
is fl ashing on the digital display. The charge
recovery mode is the same as a low battery charge state, access to some functions is limited while the
watch charge is recovering. Normal operation will resume after recovery is complete. For more
information, refer to “Power Recovery Mode” (page E-17).
A fl ashing
CHARGE
indicator means that the charge level of the watch has suddenly dropped.
Immediately expose the watch to light to charge it.
Time Calibration Signal
The information in this section applies only when
LON
,
PAR
,
ATH
,
HKG
,
HNL
,
ANC
,
LAX
,
DEN
,
CHI
,
NYC
, or
TYO
is selected as the Home City. You need to adjust the current time manually when any other
city is selected as the Home City.
E-105
The display shows the ERR indicator when I check the result of the latest receive operation.
Possible Cause Remedy Page
You are wearing or moving the
watch, or performing a button
operation during the signal
receive operation.
The watch is in an area with
poor reception conditions.
Keep the watch in an area where reception conditions are good
while the signal receive operation is performed.
E-22
You are in an area where signal
reception is not possible for
some reason.
See “Approximate Reception Ranges”. E-21
The calibration signal is not
being transmitted for some
reason.
Check the website of the organization that maintains the time
calibration signal in your area for information about its down times.
Try again later.
The current time setting changes after I set it manually.
You may have the watch confi gured for auto receive of the time calibration signal (page E-23), which will
cause the time to be adjusted automatically according to your currently selected Home City. If this results
in the wrong time setting, check your Home City setting and correct it, if necessary (page E-34).
E-106
The current time setting is off by one hour.
Possible Cause Remedy Page
Signal reception on a day for
switching between standard
time/daylight saving time (DST)
may have failed for some reason.
Perform the operation under “To get ready for a receive operation”.
The time setting will be adjusted automatically as soon as signal
reception is successful.
E-22
If you are unable to receive the time calibration signal, change the
standard time/daylight saving time (DST) setting manually.
E-36
Auto receive is not performed or you cannot perform manual receive.
Possible Cause Remedy Page
The watch is not in the
Timekeeping Mode.
Auto receive is performed only while the watch is in the Timekeeping
Mode. Enter the Timekeeping Mode.
E-31
Your Home City setting is wrong. Check your Home City setting and correct it, if necessary. E-34
There is not enough power for
signal reception.
Expose the watch to light to charge it. E-14
E-107
Signal reception is being performed successfully, but the time and/or day is wrong.
Possible Cause Remedy Page
Your Home City setting is wrong. Check your Home City setting and correct it, if necessary. E-34
The DST setting may be
incorrect.
Change the DST setting to Auto DST. E-34
Calibration signal interference
caused the time and/or date
setting to be adjusted
incorrectly.
Perform manual calibration signal receive. E-24
E-108
Specifi cations
Accuracy at normal temperature:
±15 seconds a month (with no signal calibration)
Digital Timekeeping:
Hour, minutes, seconds, a.m. (
A
)/ p.m. (
P
), month, day, day of the week
Time format: 12-hour and 24-hour
Calendar system: Full Auto-calendar pre-programmed from the year 2000 to 2099
Other: Five display formats (day of the week, month, day; barometric pressure change, month, day;
hour, minute, second; World Time hour, minute; Moon age); Home City code (can be assigned
one of 29 city codes
+
UTC); standard time / daylight saving time (summer time)
Analog Timekeeping:
Hour, minutes (hand moves every 10 seconds), seconds
Time Calibration Signal Reception:
Auto receive 6 times a day (5 times a day for the Chinese calibration
signal) ; Remaining auto receives cancelled as soon as one is successful; Manual receive;
Receive Mode
Receivable Time Calibration Signals: Mainfl ingen, Germany (Call Sign: DCF77, Frequency: 77.5
kHz); Anthorn, England (Call Sign: MSF, Frequency: 60.0 kHz); Fort Collins, Colorado, the
United States (Call Sign: WWVB, Frequency: 60.0 kHz); Fukushima, Japan (Call Sign: JJY,
Frequency: 40.0 kHz); Fukuoka/Saga, Japan (Call Sign: JJY, Frequency: 60.0 kHz) ; Shangqiu
City, Henan Province, China (Call Sign: BPC, Frequency: 68.5 kHz)
Barometer:
Measurement and display range:
260 to 1,100 hPa (or 7.65 to 32.45 inHg)
Display unit: 1 hPa (or 0.05 inHg)
Other: Calibration; Barometric pressure graph; Barometric pressure differential pointer; Barometric
pressure change indicator
E-109
Digital Compass:
60 seconds continuous reading; 16 directions; Angle value 0° to 359°; Measurement
unit: 1° (digital display)/6° (hand); North indicated by second hand: Compass calibration
(bidirectional, magnetic declination angle)
Altimeter:
Measurement range: –700 to 10,000 m (or –2,300 to 32,800 ft.) without reference altitude
Display range: –3,000 to 10,000 m (or –9,840 to 32,800 ft.)
Negative values can be caused by readings produced based on a reference altitude or due to
atmospheric conditions.
Measurement Unit: 1 m (or 5 ft.)
Current Altitude Data: 1 hour - every second for the fi rst 3 minutes, followed by every 5 seconds for
the remainder of the hour (
0'05
); 12 hours - every second for the fi rst 3 minutes, followed by
every 2 minutes for the remainder of the 12 hours (
2'00
)
Other: Reference altitude setting; Altitude differential (–100 to +100m/–1,000 to +1,000m); Altitude
measurement interval (
0'05
or
2'00
)
Thermometer:
Measurement and display range: –10.0 to 60.0°C (or 14.0 to 140.0°F)
Display unit: 0.1°C (or 0.2°F)
Other: Calibration
Pressure Sensor Precision:
Measurement accuracy: Within ±3hPa (0.1 inHg) (Altimeter accuracy: Within ± 75m (246 ft.))
Values are guaranteed for a temperature range of –10°C to 40°C (14°F to 104°F).
Precision is lessened by strong impact to either the watch or the sensor, and by temperature
extremes.
E-110
Bearing Sensor Precision:
Direction: Within ±10°
Values are guaranteed for a temperature range of 10°C to 40°C (50°F to 104°F).
North indicated by second hand: Within ±2 segments
Temperature Sensor Precision:
±2°C (±3.6°F) in range of –10°C to 60°C (14.0°F to 140.0°F)
World Time:
29 cities (29 time zones), UTC (Universal Time Coordinated); Home City/World Time City
switching; one-touch UTC zone access
Other: Daylight Saving Time/Standard Time
Tide/Moon Data:
Tide levels (Tide Graph), Moon age; date selection; time selection (Tide Graph only)
Stopwatch:
Measuring unit: 1/100 second
Measuring capacity: 23:59' 59.99"
Measuring modes: Elapsed time, split time, two fi nishes
Countdown Timer:
Measuring unit: 1 second
Countdown range: 60 minutes
Setting unit: 1 minute
Alarms:
5 Daily alarms; Hourly time signal
Illumination:
LED light; Selectable illumination duration (approximately 1.5 seconds or 3 seconds); Auto
Light Switch (Full Auto Light operates only in the dark)
Other:
Battery power indicator; Power Saving; Button operation tone on/off; alarm test; auto hand position
adjustment; hand shift feature (to view digital info)
E-111
Power Supply:
Solar panel and one rechargeable battery
Approximate battery operating time: 6 months (from full charge to Level 4) under the following
conditions:
Light: 1.5 seconds/day
Beeper: 10 seconds/day
Direction readings: 20 times/month
Climbs: Once (approximately 1 hour of altitude readings)/month
Barometric pressure change indicator readings: Approximately 24 hours/month
Barometric pressure graph: Readings every 2 hours
Time calibration receive: 4 minutes/day
Display: 18 hours/day
Frequent use of illumination runs down the battery. Particular care is required when using the auto
light switch (page E-98).
Operation Guide 5371
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Casio 5371 - GWN-1000 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Casio 5371 - GWN-1000 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,79 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Casio 5371 - GWN-1000

Casio 5371 - GWN-1000 Gebruiksaanwijzing - Deutsch - 15 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info