552993

Casio 5081 Handleiding

2
Verklein
Vergroot
Pagina terug
1/4
Pagina verder
Operation Guide 5081
2
To specify a distance value
1. In the Stopwatch Mode, make sure the stopwatch is
stopped and reset to all zeros.
• If you need to reset the stopwatch to all zeros, press A.
2. Hold down A for about three seconds until the watch
beeps, DIST (
) appears in the lower right display,
and the left digit of the current distance value setting
flashes in the lower left display.
• This is the distance value setting mode.
3. Press C to move the flashing between the values on
the left side and right side of the distance value digit
decimal point.
4. While either the left or right distance value is flashing,
use D (+) and B (–) to change it.
• You can specify a distance value in the range of 0.1 to
99.9.
5. After specifying the distance value you want, press A
to exit the setting mode.
l
l
l
l
l
l
l
l
l
l
l
l
l
How speed is indicated
• While an elapsed time measurement operation is being
performed in the Stopwatch Mode, the watch will display
a speed value, which is calculated based on the
distance you specified and the elapsed time. The speed
is indicated by the upper right dial, two indicators (1000
and MACH), and the speed hand.
• The upper right dial indicates the 100s digit value.
• 1000 appears when the speed exceeds 1,000.
• MACH appears when the speed exceeds 1,226.
• The speed hand indicates speed values less than 100.
Only even-numbered values are indicated.
Example:
At a speed of 1,740, the upper right dial indicates 1000
and MACH is displayed.
The upper right dial indicates 700.
The speed hand indicates 40.
• Speed can be indicated from 0 to 1998. OVER is
indicated by the speed hand when the speed exceeds
1998.
Speed hand
Upper
right dial
OVER
Mach (MACH)
Speed (1000)
Time Measurement
You need to specify either lap time or split time measurement before you start a
stopwatch operation.
• If you want to measure total elapsed time, select split time measurement.
To specify lap time or split time readings
1. In the Stopwatch Mode, make sure the stopwatch is stopped and reset to all zeros.
• Make sure that
LAP (lap times) or SPL (split times) is shown in the lower right
display.
• If you need to reset the stopwatch to all zeros, press A.
2. Press A to toggle between
LAP
(lap times) and
SPL
(split times) in the lower right
display.
▲
▲
A
Elapsed Time Measurement
Use the following procedure to measure elapsed time, without taking lap time or split
time readings.
To perform elapsed time measurement
Select split time (
SPL
) measurement and then perform the following button operations.
D Start ➝ D Stop ➝ A Reset
• If you have a distance value specified for the current elapsed time measurement, the
upper right dial and speed hand will indicate the overall speed when you press D to
stop the elapsed time operation.
• After pressing D to stop an elapsed time operation, you could press D again to
restart from the point where you left off.
Lap Time
A lap time reading shows the time elapsed since the last
lap time reading was taken.
• If you want the watch to calculate the speed of each lap
(when all of the laps are the same distance), specify the
lap distance for the distance setting.
• If you want the watch to calculate the speed of the entire
race, specify the race distance for the distance setting. A
speed will be indicated each time you take a lap
reading, but these lap speeds will not indicate actual
speed of the entire race.
To set up the stopwatch to take lap time readings
1. In the Stopwatch Mode, make sure the stopwatch is stopped and reset to all zeros.
• If you need to reset the stopwatch to all zeros, press A.
2. Make sure that
LAP
(lap times) is shown in the lower right display.
• If
SPL
(split times) is displayed, press A to toggle it to
LAP
.
Lap time
To perform a lap time measurement
Select lap time (
LAP
) measurement and then perform the
following button operations.
D Start ➝ A Lap* ➝ A Lap* ➝
D Stop ➝ A Reset
* The lap time is released automatically in about 12
seconds.
• You can press A to take lap readings as many times as
you like. The LAP indicator flashes while a lap reading is
displayed.
• A lap number (#01 through #99) alternates with the lap
hour value in the lower right display while a lap time
reading is displayed. If you take more than 99 lap
readings, the lap number will restart from #00 following
lap #99.
• Pressing D to stop elapsed time measurement displays
the time (and speed if a distance is specified) of the final
lap.
Lap number
Speed
(calculated)
Minutes
Seconds
LAP
indicator
1/1000
seconds
Split Time
A split time reading shows the time elapsed since the
beginning of the current time measurement.
• If you want the watch to calculate the speed of the race,
specify the race distance for the distance setting.
• For split time readings, you can specify the total race
distance only. Though the watch will indicate a speed
each time you take a split reading, they will be based on
the total race distance, and so they will not indicate
actual intermediate split speeds.
To set up the stopwatch to take split time readings
1. In the Stopwatch Mode, make sure the stopwatch is stopped and reset to all zeros.
• If you need to reset the stopwatch to all zeros, press A.
2. Make sure that
SPL
(split times) is shown in the lower right display.
• If
LAP
(lap times) is displayed, press A to toggle it to
SPL
.
Split time
To perform a split time measurement
Select split time (
SPL
) measurement and then perform
the following button operations.
D Start ➝ A Split ➝ A Split Release* ➝
D Stop ➝ A Reset
* The split time is released automatically if you do not
press A within about 12 seconds.
• You can press A to take split readings as many times
as you like. The SPLIT indicator flashes while a lap
reading is displayed.
• The stopwatch continues elapsed time measurement
internally while a split time reading is displayed.
Pressing A to release the split will switch the lower left
display to the elapsed time measurement, or you also
could press D to stop elapsed time measurement
instead.
• Pressing D to stop elapsed time measurement displays
the time (and speed if a distance is specified) of the final
split (which is the overall elapsed time).
Hour
1/1000
seconds
Minutes
Seconds
Speed (calculated)
SPLIT indicator
To measure times with the stopwatch
Elapsed Time
Lap Time
Split Time
D
Start Stop Reset
D
➤ ➤
A
D
Start
(
SPL
displayed)
Split Split release Stop
A
D
A
➤ ➤ ➤
Reset
A
➤
D
Start
(
LAP
displayed)
Lap
(Lap01)
Stop Reset
D
A
A
➤ ➤ ➤
A
➤
Lap
(Lap02)
Countdown Timer
You can set the countdown timer start time within a range
of one minute to 24 hours. An alarm sounds when the
countdown reaches zero.
• You also can select auto-repeat, which automatically
restarts the countdown from the original value you set
whenever zero is reached.
• All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
C.
Seconds
Auto-repeat off
Start time
(Hours
Minutes)
To use the countdown timer
Press D while in the Countdown Timer Mode to start the countdown timer.
• When the end of the countdown is reached, the alarm will sound for 10 seconds or
until you stop it by pressing any button.
• The countdown time is reset to its starting value automatically after the alarm stops
if auto-repeat is turned off.
• When auto-repeat is turned on, the countdown will restart automatically without
pausing when it reaches zero.
• The countdown timer measurement operation continues even if you exit the
Countdown Timer Mode.
• Press D while a countdown operation is in progress to pause it.
Press D again to resume the countdown.
• To stop a countdown timer operation completely, first pause it (by pressing D), and
then press A. This returns the countdown time to its starting value.
To configure countdown start time and auto-repeat settings
1. While the countdown start time is on the display in the
Countdown Timer Mode, hold down A for about three
seconds until the hour setting of the countdown start
time starts to flash. This is the setting mode.
• If the countdown start time is not displayed, use the
procedure under “To use the countdown timer” to
display it.
2. Press C to move the flashing in the sequence shown
below, and select the setting you want to change.
Start Time
(Minutes)
Auto-Repeat
On/Off
Start Time
(Hours)
3. Perform the following operations, depending on which setting currently is selected
on the display.
• While the start time setting is flashing, use D (+) and B (–) to change it.
• While the auto-repeat on/off setting is flashing on the display, press
D
to toggle
auto-repeat on (
) and off ( ).
Start time
(Hours
Minutes)
Auto-repeat on
4. Press A to exit the setting mode.
• The auto-repeat on (
) is displayed on the Countdown Timer Mode screen while
this function is turned on.
2

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Casio-5081

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Casio 5081 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Casio 5081 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,67 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Casio 5081

Casio 5081 Gebruiksaanwijzing - Nederlands - 4 pagina's

Casio 5081 Gebruiksaanwijzing - Deutsch - 4 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info