624842

Casio 3414 - PRW-S3500 Handleiding

13
Verklein
Vergroot
Pagina terug
1/15
Pagina verder
E-96
To specify standard time or daylight saving time (DST) for a city
1. In the World Time Mode, use
A
(East) and
C
(West) to scroll through
the available city codes.
• Keep scrolling until the city code whose Standard Time/Daylight
Saving Time setting you want to change is displayed.
2. Hold down
E
for at least two seconds.
• Keep
E
depressed until the current setting (DST Hold ON or DST
Hold OFF) starts to fl ash on the display.
• DST Hold ON means that summer time is enabled, and that the
current time is advanced accordingly. DST Hold OFF means that
summer time is disabled, and that the current time shows standard
time.
• This toggles the city code you selected in step 1 between Daylight
Saving Time (DST indicator displayed) and standard time (DST
indicator not displayed).
• Using the World Time Mode to change the DST setting of the
city code that is selected as your Home City also will change the
Timekeeping Mode time DST setting.
• Note that you cannot switch between standard time/daylight
saving time (DST) while UTC is selected as the World Time City.
• Note that the standard time/daylight saving time (DST) setting
affects only the currently selected time zone. Other time zones are
not affected.
DST indicatorDST indicator
E-97
Illumination
The display of the watch is illuminated for easy reading in the dark.
The watch’s auto light switch turns on illumination automatically when
you angle the watch towards your face.
• The auto light switch must be turned on (page E-99) for it to operate.
To turn on illumination manually
Press
L
in any mode to illuminate the display.
• You can use the procedure below to select either 1.5 seconds or three
seconds as the illumination duration. When you press
L
, the display
will remain illuminated for about 1.5 seconds or three seconds,
depending on the current illumination duration setting.
• The above operation turns on illumination regardless of the current
auto light switch setting.
• Illumination is disabled during time calibration signal reception, while
confi guring sensor measurement mode settings, and during bearing
sensor calibration.
To change the illumination duration
1. In the Timekeeping Mode, hold down
E
for at least two seconds. First,
SET Hold
will fl ash on the
display, and
CITY
will be displayed in the upper display. After that, the currently selected city code and
city name will scroll across the upper display. Keep
E
depressed until the scrolling starts.
2. Use
D
to cycle through the setting screens until
LIGHT
appears in the upper display.
• The current illumination duration setting (1 or 3) will be fl ashing in the middle display.
• See the sequence in step 2 of the procedure under “To change the current time and date
settings manually” (page E-30) for information about how to scroll through setting screens.
E-98
3. Press
A
to toggle the illumination duration between three seconds (
3
displayed) and 1.5 seconds (
1
displayed).
4. After all of the settings are the way you want, press
E
twice to exit the setting screen.
About the Auto Light Switch
Turning on the auto light switch causes illumination to turn on,
whenever you position your wrist as described below in any mode.
Moving the watch to a position that is parallel to the ground and
then tilting it towards you more than 40 degrees causes
illumination to turn on.
Warning!
•
Always make sure you are in a safe place whenever you are reading the display of the watch
using the auto light switch. Be especially careful when running or engaged in any other activity
that can result in accident or injury. Also take care that sudden illumination by the auto light
switch does not startle or distract others around you.
•
When you are wearing the watch, make sure that its auto light switch is turned off before riding
on a bicycle or operating a motorcycle or any other motor vehicle. Sudden and unintended
operation of the auto light switch can create a distraction, which can result in a traffi c accident
and serious personal injury.
More than
40°
Wear the watch on the
outside of your wrist
More than
40°
Wear the watch on the
outside of your wrist
E-99
Note
• This watch features a “Full Auto Light”, so the auto light switch operates only when available light is
below a certain level. It does not illuminate the display under bright light.
• The auto light switch is always disabled, regardless of its on/off setting, when any one of the following
conditions exists.
While an alarm is sounding
While a bearing sensor calibration operation is being performed in the Digital Compass Mode
While a receive operation is in progress in the Receive Mode
While a sunrise or sunset time is being calculated
While in a sensor mode, an auto light switch operation is performed after a sensor reading
To turn the auto light switch on and off
In the Timekeeping Mode, hold down
L
for at least three seconds to
toggle the auto light switch on (
LT
displayed) and off (
LT
not displayed).
• The auto light switch on indicator (
LT
) is on the display in all modes
while the auto light switch is turned on.
• The auto light switch turns off automatically whenever battery power
drops to Level 4 (page E-10).
Auto light switch on
indicator
Auto light switch on
indicator
E-100
Illumination Precautions
• The LED that provides illumination loses power after very long use.
• Illumination may be hard to see when viewed under direct sunlight.
• Illumination turns off automatically whenever an alarm sounds.
• Frequent use of illumination runs down the battery.
Auto light switch precautions
• Wearing the watch on the inside of your wrist, movement of your arm, or vibration of your arm can
cause frequent activation of the auto light switch and illumination of the display. To avoid running down
the battery, turn off the auto light switch whenever engaging in activities that might cause frequent
illumination of the display.
• Note that wearing the watch under your sleeve while the auto light switch is turned on can cause
frequent illumination of the display and can run down the battery.
• Illumination may not turn on if the face of the watch is more than 15 degrees above
or below parallel. Make sure that the back of your hand is parallel to the ground.
• Illumination turns off after the preset illumination duration (page E-97), even if you
keep the watch pointed towards your face.
• Static electricity or magnetic force can interfere with proper operation of the auto
light switch. If illumination does not turn on, try moving the watch back to the
starting position (parallel with the ground) and then tilt it back towards your face
again. If this does not work, drop your arm all the way down so it hangs at your
side, and then bring it back up again.
• You may notice a very faint clicking sound coming from the watch when it is shaken
back and forth. This sound is caused by mechanical operation of the auto light
switch, and does not indicate a problem with the watch.
E-101
Other Settings
The button operation tone sounds any time you press one of the watch’s buttons. You can turn the button
operation tone on or off as desired.
• Even if you turn off the button operation tone, the alarm, Hourly Time Signal, barometric pressure
change alert, and Countdown Timer Mode alarm all operate normally.
To turn the button operation tone on and off
1. In the Timekeeping Mode, hold down
E
for at least two seconds.
First,
SET Hold
will fl ash on the display, and
CITY
will be displayed in
the upper display. After that, the currently selected city code and city
name will scroll across the upper display. Keep
E
depressed until the
scrolling starts.
2. Use
D
to cycle through settings on the display until the current button
operation tone (
MUTE
or
key
) is displayed.
• See the sequence in step 2 of the procedure under “To change the
current time and date settings manually” (page E-30) for
information about how to scroll through setting screens.
3.
Press
A
to toggle the button operation tone on (
key
) and off (
MUTE
).
4. After all of the settings are the way you want, press
E
twice to exit the
setting screen.
Note
• The mute indicator is displayed in all modes when the button
operation tone is turned off.
Mute indicatorMute indicator
E-102
To turn Power Saving on or off
1. In the Timekeeping Mode, hold down
E
for at least two seconds.
First,
SET Hold
will fl ash on the display, and
CITY
will be displayed in
the upper display. After that, the currently selected city code and city
name will scroll across the upper display. Keep
E
depressed until the
scrolling starts.
2. Use
D
to cycle through the setting screens until the current power
saving setting (
On
or
OFF
) is displayed.
• POWER SAVING will scroll across the upper display at this time.
• See the sequence in step 2 of the procedure under “To change
the current time and date settings manually” (page E-30) for
information about how to scroll through setting screens.
3. Press
A
to toggle Power Saving on (
On
) and off (
OFF
).
4. After all of the settings are the way you want, press
E
twice to exit the
setting screen.
Note
• The Power Saving on indicator (PS) is on the display in all modes
while Power Saving is turned on.
Power saving
on indicator
Power saving
on indicator
E-103
Troubleshooting
Time Setting
See “Radio Controlled Atomic Timekeeping” (page E-14) for information about adjusting the time setting
according to a time calibration signal.
■
The current time setting is off by hours.
Your Home City setting may be wrong (page E-28). Check your Home City setting and correct it, if
necessary.
■
The current time setting is off by one hour.
If you are using the watch in an area where time calibration signal reception is possible, see “To confi gure
Home City and summer time settings” (page E-28).
If you are using in the watch in an area where time calibration signal reception is not possible, you may
need to change your Home City’s standard time/daylight saving time (DST) setting manually. Use the
procedure under “To change the current time and date settings manually” (page E-30) to change the
standard time/daylight saving time (DST) setting.
Sensor modes
■
I can’t change the temperature, barometric pressure, and altitude display units.
When
TYO
(Tokyo) is selected as the Home City, the altitude unit is set automatically to meters (m), the
barometric pressure unit to hectopascals (hPa), and the temperature unit to Celsius (°C). These settings
cannot be changed.
Operation Guide 3414
… 13

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Casio 3414 - PRW-S3500 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Casio 3414 - PRW-S3500 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,66 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Casio 3414 - PRW-S3500

Casio 3414 - PRW-S3500 Gebruiksaanwijzing - Deutsch - 15 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info