586141

Casio 3205 Handleiding

5
Verklein
Vergroot
Pagina terug
1/15
Pagina verder
Operation Guide 3134 3205
5
•You can turn off (OFF) magnetic declination correction (which effectively
makes the magnetic declination angle: 0°) by pressing A and C at the
same time.
•The illustration, for example, shows the value you should input and the
direction setting you should select when the map shows a magnetic
declination of 1° West.
3. When the setting is the way you want, press E to exit the setting screen.
Precautions about bidirectional calibration
•You can use any two opposing directions for bidirectional calibration. You
must, however, make sure that they are 180 degrees opposite each other.
Remember that if you perform the procedure incorrectly, you will get wrong
bearing sensor readings.
•Make sure that you do not move the watch while calibration of either
direction is in progress.
•You should perform bidirectional calibration in an environment that is the
same as that where you plan to be taking direction readings. If you plan to
take direction readings in an open field, for example, calibrate in an open
field.
To perform bidirectional calibration
1. In the Digital Compass Mode, hold down E
for about two seconds until the magnetic
declination angle and magnetic declination
angle direction values start to flash on the
display. This is the setting screen.
2. Press D to display the bidirectional
calibration screen.
•At this time, the north pointer flashes at the
12 o’clock position to indicate that the watch
is ready to calibrate the first direction.
3. Place the watch on a level surface facing any direction you want, and
press C to calibrate the first direction.
•xxx is shown on the display while calibration is being performed. When
calibration is successful, the display will show OK and x2x, and the
north pointer flashes at the 6 o’clock position. This means that the watch
is ready for calibration of the second direction.
4. Rotate the watch 180 degrees.
l
l
l
l
l
l
l
l
l
l
l
l
l
l
5. Press C again to calibrate the second direction.
•xxx is shown on the display while calibration is being performed. When
calibration is successful, the display will show OK and the Digital Compass
Mode (showing the angle value) screen.
•If xxx appears and then changes to ERR (error) on the calibration
screen, it means that there is something wrong with the sensor. When
ERR disappears after about one second, try performing the calibration
again. If ERR keeps appearing, contact your original dealer or nearest
authorized CASIO distributor to have the watch checked.
To perform northerly calibration
1. In the Digital Compass Mode, hold down E
for about two seconds until the magnetic
declination angle and magnetic declination
angle direction values start to flash on the
display. This is the setting screen.
2. Press D twice to display the northerly
calibration screen.
•At this time, -N- (north) appears on the
display.
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
3. Place the watch on a level surface, and position it so that its 12 o’clock
position points north (as measured with another compass).
4. Press C to start the calibration operation.
• --- is shown on the display while calibration is being performed. When
calibration is successful, the display will show OK and the Digital Compass
Mode (with 0° shown as the angle value).
•If --- appears and then changes to ERR (error) on the calibration
screen, it means that there is something wrong with the sensor. When
ERR disappears after about one second, try performing the calibration
again. If ERR keeps appearing, contact your original dealer or nearest
authorized CASIO distributor to have the watch checked.
Using the Digital Compass While Mountain Climbing or
Hiking
This section describes three real-life situations where you could use the
watch’s built-in digital compass.
•To set a map and find your current location
Having an idea of your current location is important when mountain
climbing or hiking. To do this, you need to “set the map”, which means to
align the map so the directions indicated on it are aligned with the actual
directions of your location. Basically what you are doing is aligning north on
the map with north as indicated by the watch.
•To find the bearing to an objective
•To determine the direction angle to an objective on a map and head in that
direction
To set a map and find your current location
1. With the watch on your wrist, position it so the
face is horizontal.
2. In the Timekeeping, Digital Compass,
Barometer/Thermometer, or Altimeter Mode,
press C to take a compass reading.
•The reading will appear on the display after
about two seconds.
3. Rotate the map without moving the watch so
the northerly direction indicated on the map
matches north as indicated by the watch.
•If the watch is configured to indicate
magnetic north, align the map’s magnetic
north with the watch indication. If the watch
has been configured with a declination to
correct to true north, align the map’s true
north with the watch indication.
•This will position the map in accordance
with your current location.
4. Determine your location as you check the
geographic contours around you.
North indicated
on the map
North indicated by
north pointer
Current
location
N
N
To find the bearing to an objective
1. Take a compass reading and then set the map
so its northerly indication is aligned with north
as indicated by the watch, and determine your
current location.
•See “To set a map and find your current
location” for information about how to
perform the above step.
2. Set the map so the direction you want to travel
on the map is pointed straight in front of you.
3. With the watch on your wrist, position it so the
face is horizontal.
4. In the Timekeeping, Digital Compass,
Barometer/Thermometer, or Altimeter Mode,
press C to take a compass reading.
•The reading will appear on the display after
about two seconds.
5. Still holding the map in front of you, turn your
body until north as indicated by the watch and
the northerly direction on the map are aligned.
12 o’clock
position
N
N
Current
location
Objective
•This will position the map relative to your current location, so the bearing to
your objective is straight ahead of you.
To determine the direction angle to an objective on a map and head
in that direction
Note
•The following procedure is possible only with a
watch that has a rotary bezel.
1. Take a compass reading and then set the map
so its northerly indication is aligned with north
as indicated by the watch, and determine your
current location.
•See “To set a map and find your current
location” for information about how to
perform the above step.
2.
As shown in the illustration to the left, change
your position so you (and the 12 o’clock position
of the watch) are pointed in the direction of
objective, while keeping the map aligned with
the readings being produced by the watch.
12 o’clock
position
N
N
Current
location
Objective
Important!
•If you want to perform both bidirectional and northerly calibration, be sure
to perform bidirectional calibration first, and then perform northerly
calibration. This is necessary because bidirectional calibration cancels any
existing northerly calibration setting.
•The more correctly you perform bidirectional calibration, the better the
accuracy of the bearing sensor readouts. You should perform bidirectional
calibration whenever you change environments where you use the bearing
sensor, and whenever you feel that the bearing sensor is producing
incorrect readings.
To perform magnetic declination correction
1. In the Digital Compass Mode, hold down E
for about two seconds until the magnetic
declination angle and magnetic declination
angle direction values start to flash on the
display. This is the setting screen.
2. Use A (+) and C (–) to change the magnetic
declination angle and magnetic declination
angle direction settings.
•You can select a value within the range of
W 90° to E 90° with these settings.
•The following explains magnetic declination
angle direction settings.
OFF: No magnetic declination correction
performed. The magnetic declination
angle with this setting is 0°.
E: When magnetic north is to the east (east declination)
W: When magnetic north is to the west (west declination)
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
Magnetic declination
angle direction
Magnetic
declination
angle value
… 5 …

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Casio-3205

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Casio 3205 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Casio 3205 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,17 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info