522102
3
Verklein
Vergroot
Pagina terug
1/5
Pagina verder
Operation Guide 3157
3
If you want to cancel bearing sensor correction, press D in step 5 instead of C.
This will return to the screen in step 2. From there you can press A to exit the
calibration screen.
The indicator will go around the display up to four times, if you do not stop it by
pressing C. After the fourth time, the watch will exit the calibration screen
automatically.
To perform magnetic declination correction
1. In the Digital Compass/Thermometer Mode, hold down
A until the indicator at the 12 o’clock position starts to
flash. This is the calibration screen.
2. Press C.
The magnetic declination angle and magnetic
declination angle direction will flash on the display.
3. Use D (+) and B (–) to change the magnetic
declination angle and magnetic declination angle
direction settings.
Magnetic
declination
angle value
Magnetic
declination
angle direction
You can select a value within the range of 90° W to 90° E with these settings.
The following explains magnetic declination angle direction settings.
0 OFF: No magnetic declination correction performed. The magnetic
declination angle with this setting is 0°.
E: When magnetic north is to the east (east declination)
W: When magnetic north is to the west (west declination)
You can turn off (0 OFF) magnetic declination correction (which effectively makes
the magnetic declination angle: 0°) by pressing D and B at the same time.
The illustration, for example, shows the value you should input and the direction
setting you should select when the map shows a magnetic declination of 1° West.
4. When the setting is the way you want, press A to exit the setting screen.
Using the Digital Compass While Mountain Climbing or Hiking
This section describes three real-life situations where you could use the watch’s built-
in digital compass.
To set a map and find your current location
Having an idea of your current location is important when mountain climbing or
hiking. To do this, you need to “set the map”, which means to align the map so the
directions indicated on it are aligned with the actual directions of your location.
Basically what you are doing is aligning north on the map with north as indicated by
the watch.
To find the bearing to an objective
To set a map and find your current location
1. With the watch on your wrist, position it so the face is
horizontal.
2. In the Timekeeping Mode, press D to take a compass
reading.
The reading will appear on the display after about two
seconds.
3. Rotate the map without moving the watch so the
northerly direction indicated on the map matches north
as indicated by the watch.
If the watch is configured to indicate magnetic north,
align the map’s magnetic north with the watch
indication. If the watch has been configured with a
declination to correct to true north, align the map’s
true north with the watch indication.
This will position the map in accordance with your
current location.
4. Determine your location as you check the geographic
contours around you.
Current
location
N
N
North indicated
on the map
North indicated by
north pointer
To find the bearing to an objective
1. Take a compass reading and then set the map so its
northerly indication is aligned with north as indicated by
the watch, and determine your current location.
See “To set a map and find your current location” for
information about how to perform the above step.
2. Set the map so the direction you want to travel on the
map is pointed straight in front of you.
3. With the watch on your wrist, position it so the face is
horizontal.
4. In the Timekeeping Mode, press D to take a compass
reading.
The reading will appear on the display after about two
seconds.
5. Still holding the map in front of you, turn your body until
north as indicated by the watch and the northerly
direction on the map are aligned.
This will position the map relative to your current location, so the bearing to your
objective is straight ahead of you.
12 oclock
position
N
N
Current
location
Objective
Questions & Answers
Question: What causes incorrect direction readings?
Answer:
Nearby source of strong magnetism, such as a household appliance, a large steel
bridge, a steel beam, overhead wires, etc., or an attempt to perform direction
measurement on a train, boat, etc. Move away from large metal objects and try
again. Note that digital compass operation cannot be performed inside a train, boat,
etc.
Question: What causes different direction readings to produce different results
at the same location ?
Answer: Magnetism generated by nearby high-tension wires is interfering with
detection of terrestrial magnetism. Move away from the high-tension wires
and try again.
Question: Why am I having problems taking direction readings indoors ?
Answer: A TV, personal computer, speakers, or some other object is interfering with
terrestrial magnetism readings. Move away from the object causing the
interference or take the direction reading outdoors. Indoor direction readings
are particularly difficult inside ferro-concrete structures. Remember that you
will not be able to take direction readings inside of trains, airplanes, etc.
World Time
World Time displays the current time in 48 cities (29 time
zones) around the world.
If the current time shown for a city is wrong, check your
Home City time settings and make the necessary
changes.
All of the operations in this section are performed in the
World Time Mode, which you enter by pressing C.
To view the time in another city
In the World Time Mode, use D (east) to scroll through
city codes (time zones).
For full information on city codes, see the “City Code
Table”.
Timekeeping
Mode time
Current time in the zone
of the selected city code
City code
To toggle a city code time between Standard Time and Daylight Saving Time
1. In the World Time Mode, use D (east) to display the
city code (time zone) whose Standard Time/Daylight
Saving Time setting you want to change.
2. Hold down A to toggle between Daylight Saving Time
(DST indicator displayed) and Standard Time (DST
indicator not displayed).
The DST indicator appears on the display whenever you
display a city code for which Daylight Saving Time is
turned on.
Note that the DST/Standard Time setting affects only the
currently displayed city code. Other city codes are not
affected.
DST indicator
Stopwatch
The stopwatch lets you measure elapsed time, split times,
and two finishes.
The display range of the stopwatch is 59 minutes, 59.99
seconds.
The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
elapsed time measurement.
All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing C.
Minutes
Current time
1/100 second
Seconds
To measure times with the stopwatch
Elapsed Time
DD D D A
Start Stop Re-start Stop Clear
Split Time
DA A D A
Start Split Split release Stop Clear
Two Finishes
DA D A A
Start Split Stop Split release Clear
JJJJ
(SPL displayed)
First runner
finishes.
Display time of
first runner.
Display time of
second runner.
Second runner
finishes.
JJJJ
JJJJ
Countdown Timer
You can set the countdown timer within a range of one
minute to 24 hours. An alarm sounds when the countdown
reaches zero.
You also can select auto-repeat, which automatically
restarts the countdown from the original value you set
whenever zero is reached.
All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
C.
Seconds
Hours Minutes
Current time
To configure countdown start time and auto-repeat settings
1. While the countdown start time is on the display in the
Countdown Timer Mode, hold down A until the hour
setting of the countdown start time starts to flash, which
indicates the setting screen.
If the countdown start time is not displayed, use the
procedure under “To use the countdown timer” to
display it.
2. Press C to move the flashing in the sequence shown
below, and select the setting you want to change.
Start Time
(Minutes)
Auto-Repeat
On/Off
Start Time
(Hours)
3. Perform the following operations, depending on which
setting is currently selected on the display.
While the start time setting is flashing, use D (+) and
B (–) to change it.
Auto-repeat on indicator
Set
0:00
to specify 24 hours.
While the auto-repeat on/off setting (0N or 0FF) is flashing on the display, press
D to toggle auto-repeat on (0N) and off (0FF).
4. Press A to exit the setting screen.
The auto-repeat on indicator (
) is displayed on the Countdown Timer Mode
screen while this function is turned on.
Frequent use of auto-repeat and the alarm can run down battery power.
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Casio 3157 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Casio 3157 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,5 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Casio 3157

Casio 3157 Gebruiksaanwijzing - Nederlands - 5 pagina's

Casio 3157 Gebruiksaanwijzing - Deutsch - 5 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info