533832
3
Verklein
Vergroot
Pagina terug
1/5
Pagina verder
Operation Guide 2888
3
To perform a currency conversion calculation
1. While the currency converter screen is displayed in the Calculator Mode, use the
keypad to input the value from which you want to convert.
2. Press [=PM] to display the conversion result.
3. Press C to clear the conversion result.
An E (error) indicator appears on the display when the result of a calculation
exceeds 8 digits. Press C to clear the error indicator.
Pressing [=PM] while a calculation result is displayed will apply the conversion rate
again to the displayed value.
Turning the Input Tone On and Off
An input tone causes the watch to beep each time you press a button or keypad key.
You can turn off the input tone if you want.
The input tone on/off setting you select in the Calculator Mode is applied to all other
modes, except the Stopwatch Mode.
Note that alarms will continue to sound even if the input tone is turned off.
To turn the input tone on and off
While the calculator screen or currency converter screen
is displayed in the Calculator Mode, hold down C for
about two seconds to toggle the input tone on (MUTE
indicator not displayed) and off (MUTE indicator
displayed).
Holding down C will also switch the Calculator Mode
screen.
The MUTE indicator is displayed in all modes when the
input tone is turned off.
MUTE indicator
Alarms
You can set up to five independent multi-function alarms
with hour, minutes, month, and day. When an alarm is
turned on, the alarm tone sounds when the alarm time is
reached. One of the alarms can be configured as a
snooze alarm or a one-time alarm, while the other four are
one-time alarms.
You can also turn on an Hourly Time Signal, which will
cause the watch to beep twice every hour on the hour.
There are five alarm screens numbered 1 through 5.
The Hourly Time Signal screen is indicated by :00.
All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing B.
Alarm time
Alarm number
Timekeeping
Mode time Alarm date
Hourly Time Signal Screen
Alarm Screen
Alarm Types
The alarm type is determined by the settings you make, as described below.
Daily alarm
Set the hour and minutes for the alarm time. This type of setting causes the alarm to
sound everyday at the time you set.
Date alarm
Set the month, day, hour and minutes for the alarm time. This type of setting causes
the alarm to sound at the specific time, on the specific date you set.
1-Month alarm
Set the month, hour and minutes for the alarm time. This type of setting causes the
alarm to sound everyday at the time you set, only during the month you set.
Monthly alarm
Set the day, hour and minutes for the alarm time. This type of setting causes the alarm
to sound every month at the time you set, on the day you set.
Note
The 12-hour/24-hour format of the alarm time matches the format you select in the
Timekeeping Mode.
To set an alarm time
1. In the Alarm Mode, use [+] and [÷] to scroll through
the alarm screens until the one whose time you want to
set is displayed.
x1 x2 x3
:00 x5 x4
You can configure alarm 1 as a snooze alarm or a
one-time alarm. Alarms 2 through 5 can be used as
one-time alarms only.
The snooze alarm repeats every five minutes.
2. After you select an alarm, hold down A until the left
hour setting of the alarm time starts to flash, which
indicates the setting screen.
This operation automatically turns on the alarm.
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
Hour : Minutes
Alarm number
AM indicator
Month Day
Press [+] Press [÷]
3. Use the keypad to input the alarm time and date.
The flashing automatically advances to the right each time you input a number.
You can also use B and C to move the flashing between input digits.
To set an alarm that does not use a month and/or day setting, input 00 for each
of the unused settings.
If you are using 12-hour timekeeping, press [=PM] while the hour or minute
setting is flashing to toggle between AM and PM.
When setting the alarm time using the 12-hour format, take care to set the time
correctly as am (A indicator) or pm (P indicator).
4. Press A to exit the setting screen.
Note that the month and day setting each appear as 00 on the setting screen when
no month or day is set. On the alarm screen, however, an unset month is shown as
x and an unset day is shown as xx. See the sample displays under To set an
alarm time.
To test the alarm
In the Alarm Mode, hold down C to sound the alarm.
Pressing C also toggles the currently display alarm or the Hourly Time Signal on
and off.
To turn alarms
22
22
2
through
55
55
5
and the Hourly Time Signal on and off
1. In the Alarm Mode, use [+] and [÷] to select a one-
time alarm (alarms 2 through 5) or the Hourly Time
Signal.
2. Press C to toggle it on and off.
The current on/off status of alarms 2 through 5 is
shown by indicators along the bottom of the displays
(al-2 through al-5). The SIG indicator shows the on (SIG
displayed)/off (SIG not displayed) status of the Hourly
Time Signal.
The alarm on indicators and Hourly Time Signal on
indicator are displayed in all modes.
While an alarm is sounding, the applicable alarm on
indicator flashes on the display.
Alarm 2 on
indicator
Alarm 4 on
indicator
Hourly time signal
on indicator
To select the operation of alarm
11
11
1
1. In the Alarm Mode, use [+] and [÷] to select alarm 1.
2. Press C to cycle through the available settings in the
sequence shown below.
Snooze alarm on One-time alarm on
SNZ al-1 al-1
Alarm off
The SNZ indicator and alarm 1 on indicator (al-1) are
displayed in all modes.
The SNZ indicator flashes during the 5-minute intervals
between alarms.
The alarm indicator (al-1 and/or SNZ) flashes while the
alarm is sounding.
SNZ
indicator
Alarm 1 on
indicator
SNZ indicator and alarm 11
11
1 on indicator
Press C.
Stopwatch
The stopwatch lets you measure elapsed time, split times,
and two finishes.
The display range of the stopwatch is 23 hours, 59
minutes, 59.99 seconds.
The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
The elapsed time measurement operation continues
even if you exit the Stopwatch Mode.
Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
elapsed time measurement.
All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing B.
Timekeeping
Mode time
Minutes
1/100 second
Seconds
Hours
To measure times with the stopwatch
C
Start Stop
Re-start Clear
C
Stop
CCA
Split Time
C
Start Split
Split release Clear
A
Stop
ACA
(SPL displayed)
Start Split Stop Clear
Split release
First runner
finishes.
Display time of
first runner.
Second runner
finishes. Display time of
second runner.
CACAA
Elapsed Time
Two Finishes
Alarm Operation
The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the
watch is in. In the case of the snooze alarm, the alarm tone operation is performed a
total of seven times, every five minutes, until you turn the alarm off or change it to a
one-time alarm.
Pressing any button or key stops the alarm tone operation.
Performing any one of the following operations during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen
Displaying the alarm
1
setting screen
3

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Casio-2888

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Casio 2888 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Casio 2888 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,49 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Casio 2888

Casio 2888 Gebruiksaanwijzing - Nederlands - 5 pagina's

Casio 2888 Gebruiksaanwijzing - Deutsch - 5 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info