Handleiding Casio 2760 (pagina 4 van 7) (Engels)

522624

Verklein

Vergroot

Pagina terug

1/7

Pagina verder

Operation Guide 2760 2761

Alarm Operation

The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the

watch is in. In the case of the snooze alarm, the alarm operation is performed a total

of seven times, every five minutes, or until you turn the alarm off.

The target alarm counts the time remaining from the current time in your Home Time

Zone until the target alarm time. Note that the target alarm repeats automatically each

day, as long as it is turned on. You need to turn off the target alarm to disable it.

• Alarm and Hourly Time Signal operations are performed in accordance with the

Timekeeping Mode digital time.

• Pressing any button stops the alarm tone operation.

• Performing any one of the following operations during a 5-minute interval between

snooze alarms cancels the current snooze alarm operation.

Displaying the Timekeeping Mode setting screen

Displaying the snooze alarm (

AL5

) setting screen

To test the alarm

In the Alarm Mode, hold down B to sound the alarm.

To turn an alarm and the Hourly Time Signal on and off

1. In the Alarm Mode, use B to select an alarm or the

Hourly Time Signal.

2. Press A to toggle it on (on displayed) and off (oF

displayed).

• You need to display the screen of a daily alarm (AL1 to

AL5) or the Hourly Time Signal in order to check its

current on/off status.

• Turning on the snooze alarm displays the snooze alarm

indicator on its Alarm Mode screen and in all modes.

• The snooze alarm indicator flashes during the 5-minute

intervals between alarms.

Snooze alarm indicator

On/Off status

Hourly Time Signal Screen

Timekeeping

Use the Timekeeping Mode to set and view the current time and date. This section

also explains how to manually set the current date and time.

• All of the operations in this section are performed in the Timekeeping Mode, which

you enter by pressing C.

▲

Press A.

Last Signal Screen

Day of week Month – Day

Press B.

Year Month – Day Hour : Minutes

PM indicator

Seconds

Setting the Digital Time and Date Manually

Make sure you select your Home Time Zone before you change the current time and

date settings. Dual Time Mode times are all displayed in accordance with the

Timekeeping Mode settings. Because of this, Dual Time Mode times will not be correct

if you do not select the proper Home Time Zone before setting the time and date in the

Timekeeping Mode.

• When setting the time and date, you can also configure settings for your Home Time

Zone (the time zone where you normally use the watch), summer time (Daylight

Saving time or DST), 12/24-hour format, and power saving on/off.

To set the digital time and date manually

1. While any screen other than the last signal screen is on

the display in the Timekeeping Mode, hold down A

until the GMT differential value starts to flash, which

indicates the setting screen.

• The second hand will move at high speed to the 12

o’clock position, where it will stop.

DST indicator

GMT differential value

• The GMT differential value indicates the time difference in hours between

Greenwich Mean Time and the currently selected time zone.

• The DST indicator indicates that Daylight Saving Time (summer time) is turned on

for the currently selected time zone.

2. Use D (+) and B (–) to select the time zone you want to use as your Home Time

Zone.

• For full details about GMT differential values, see the “Time Zone Table”.

3. Press C to move the flashing in the sequence shown below to select other

settings.

4. When the setting you want to change is flashing, use B and D to change it as

described below.

12/24-Hour

Format

GMT differential

value

DST

Power

Saving

Day

Hour

Minutes

Seconds

YearMonth

5. Press A to exit the setting screen.

• When you exit the setting screen, the analog hands are adjusted automatically to

match the digital time. See “Analog Timekeeping” for more information.

Screen To do this:

Change the time zone

Toggle between Daylight Saving Time (on),

Standard Time (OFF), or Auto DST (A)

Toggle between 12-hour (12H) and 24-hour

(24H) timekeeping

Reset the seconds to 00

Change the hour or minutes

Change the year, month, or day

Toggle power saving on (on) and off (OFF)

Do this:

Use D (+) and B (–).

Press D.

Use D (+) and B (–).

Press D.

• Auto DST (A) can be selected only while +0.0, +1.0 or +2.0 is selected as the Home

Time Zone. For more information, see “Daylight Saving Time (DST)” below.

Daylight Saving Time (DST)

Daylight Saving Time (summer time) advances the time setting by one hour from

Standard Time. Remember that not all countries or even local areas use Daylight

Saving Time.

The time calibration signals include both Standard Time and DST data. When the auto

DST setting is turned on, the watch switches between Standard Time and DST

(summer time) automatically in accordance with the signal it receives.

• The auto DST setting can be turned on only while +0.0, +1.0 or +2.0 is selected as

the Home Time Zone.

• If you experience problems receiving the time calibration signal in your area, it is

probably best to switch between Standard Time and Daylight Saving Time (summer

time) manually.

To change the Daylight Saving Time (summer time) setting

1. While any screen other than the last signal screen is on the display in the

Timekeeping Mode, hold down A until the GMT differential value starts to flash,

which indicates the setting screen.

2. Press C to display the DST setting screen.

3. Press D to cycle through the DST settings in the sequence shown below.

4. Press A to exit the setting screen.

• The DST indicator appears on the display to indicate that Daylight Saving Time is

turned on.

Auto DST (A) DST off (OFF) DST on (on)

Analog Timekeeping

The analog time of this watch is synchronized with the digital time. The analog time

setting is adjusted automatically whenever you change the digital time.

Note

• The hands for the analog timepiece move to adjust to a new setting whenever any of

the following occurs.

When you change the digital time setting manually

When the digital time setting is changed by time calibration signal reception

When you change the Home Time Zone and/or DST setting

• Whenever you need to adjust both the digital and the analog time settings manually,

make sure you adjust the digital setting first.

• Depending on how much the hands have to move in order to adjust to the digital

time, it may take some time before they stop moving.

To adjust the analog time

1. In the Timekeeping Mode, press C five times to enter

the Hand Setting Mode.

2. Hold down A until – 0 0 – starts to flash, which

indicates the analog setting screen.

• The second hand will move at high speed to the 12

o’clock position, where it will stop.

3. If the second hand is not pointing precisely at 12 o’clock

at this time, use D to adjust its position.

• Each press of D causes the second hand to advance

by one second.

4. Press C. This will cause the Timekeeping Mode time

on the digital display to flash, which indicates that

adjustment of hour and minute hands is selected.

5. Use D (+) and B (–) to move the hands in 20-second

units.

• Holding down either button moves the hands at high

speed.

Minute hand

Second hand

Hour hand

24-hour dial

• Adjust the analog time so it matches the digital time. Note that the 24-hour dial

hand moves in coordination with the hour and minute hands. When adjusting the

analog time, keep an eye on the 24-hour dial hand to make sure that it is in the

correct am/pm position.

• To move the hands forward a long way, hold down D, press B, and then release

both buttons.

• To move the hands back a long way, hold down B, press D, and then release

both buttons.

• The above operations cause the hands to move at high speed until you press any

button or until the hands complete one 24-hour cycle (two revolutions). Hand

movement also stops if an alarm starts to sound.

6. Press A twice to exit the setting screen.

• The first press of A causes 00:00.00 to appear on the display (indicating the

stopwatch 1/20 second dial hand adjustment screen). Pressing A the second time

exits the setting screen.

• To return to the Timekeeping Mode, press C.

Illumination

Two LEDs (light-emitting diodes) illuminate the face of the

watch for easy reading in the dark.

The watch’s auto light switch automatically illuminates the

face when you angle the watch towards your face.

• The auto light switch must be turned on (indicated by

the auto light switch on indicator) for it to operate.

• You can specify 1.5 seconds or 2 seconds as the

illumination duration.

• See “Illumination Precautions” for other important

information.

To illuminate the face of the watch

In any mode (except when a setting screen is on the display), press D to illuminate

the face of the watch.

• The above operation turns on illumination regardless of the current auto light switch

setting.

Auto light switch

on indicator

To specify the illumination duration

1. While any screen other than the last signal screen is on

the display in the Timekeeping Mode, hold down A

until the GMT differential value starts to flash, which

indicates the setting screen.

2. Press C three times to move the flashing to the

second setting.

3. Press B to toggle the illumination duration setting

between 2 seconds (“.” displayed in front of seconds)

and 1.5 seconds (“.” not displayed).

4. Press A to exit the setting screen.

Casio 2760 Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Stel vragen via chat aan uw handleiding

Andere handleiding(en) van Casio 2760

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info