497568

Cardo scala-rider TeamSet Handleiding

3
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
TeamSet
™
Guide d’Utilisation
Guia do Usuário
Handleiding
Инструкция пользователя
User Guide
communication in motion
™
™
2
scala rider
®
TeamSet
™
English
CONTENTS OF RETAIL BOX
INTRODUCTION
Congratulations, and thank you for choosing the scala rider
TeamSet Bluetooth® Headset package for Motorcycle helmets.
The retail box of the scala rider TeamSet contains two headset units:
one headset for the driver and a second headset for the passenger:
The Driver’s unit includes a Bluetooth module that allows the
following uses:
1. Bluetooth headset for mobile phone communication*, supporting
Headset* and Handsfree* proles (10m / 33 ft. range)
2. Transmitting GPS navigation instructions from a Bluetooth enabled
GPS device
3. Intercom communications Driver-Passenger – Full Duplex
(10m/33 ft. range)
4. MP3 Connectivity to an MP3 player
The Passenger unit contains an intercom module and performs
the following uses only:
1. Intercom communications Passenger-Driver Full Duplex (10m/30 ft.
range)
2. MP3 connectivity to an MP3 player
This manual will help you operate the headset, but you shouldrst
familiarize yourself with the Bluetooth functionality of your mobile
phone and/or GPS device before using the Product.
Cardo wishes you an enjoyable and safe scala rider TeamSet
experience!
____________________
* Mobile phones that do not support the Bluetooth Handsfree prole may prevent you
from using the Redial and Call Reject features.
Intercom button
CTRL – Control Button
Charging
Jack
Volume
Down
Volume
Up
NOTE: The use of
two speakers may be
illegal in certain jurisdictions. Please
check the local regulations and act
accordingly.
Two Headsets
Two Helmet Clamps
Tab
Sliding Plate
Microphone
Right Speaker
(long cord)
Left Speaker
(short cord)
Back
Plate
MP3
Jack
3
scala rider
®
TeamSet
™
Wall Charger
2 Allen Wrenches
2 Sets of Velcro Pads
2 MP3 Cables
2 MP3 Cable Holders
2 Glue Plates
2 Pre-moistened Towelettes
2 Carry-Pouches
4 Microphone Sponges
Flat sponges for full-face helmets and round sponges for other helmet types
User Guide, including Warranty and Registration form
IMPORTANT:
Your headsets are water-resistant devices, designed for use under
moderate rain or snow conditions. However, the headsets are not
waterproof and should not be used under severe weather conditions.
The cover tongue protecting the Charging Jack should be kept tightly
closed at all times to prevent moisture from entering the device.
BEFORE USING (CHARGING THE
HEADSET)
Make sure that the headset is fully charged for at least four hours
before initial use.
1. Connect the wall charger to the headset’s Charging Jack (located
between the two Volume Buttons).
2. While charging, the Red Light turns on (it may take up to 15
seconds until the Red Light turns on). When charging is complete,
the Red Light will turn o.
SET UP AND CONFIGURATION
Mobile Phone MP3 Player
Driver and
Passenger
GPS
Driver-to-Passenger
Full Duplex Intercom
Connection
(10 m/30 ft.)
SET UP FOR MOBILE PHONE CALLS
If you have a Bluetooth enabled mobile phone and would like to
make and receive phone calls using the scala rider TeamSet
Driver’s unit, you mustrst pair your headset to the mobile phone.
Pairing is a one time process. Once the headset is paired
to a specific mobile phone during this Setup Procedure, they will
remain paired and automatically recognize each other whenever
they are within range. If the connection between the phone and
headset is lost, tap the CTRL button to reconnect the devices.
TO PAIR THE SCALA RIDER TEAMSET TO A BLUETOOTH MOBILE
PHONE
1. Turn on your phone and make sure its Bluetooth function is
activated.
2. With the Driver’s unit headset turned OFF, press and hold
the CTRL Button until the Red and Blue Lights begin rapidly
alternating.
4
scala rider
®
TeamSet
™
English
3. Search for Bluetooth devices on your phone by following the
phone’s instructions. Please consult your phone’s User Manual
for more information.
4. After a few seconds the phone will list the scala-rider
TeamSet as a discovered device. Select it and follow your
phone’s instructions to accept the pairing.
5. When prompted enter 0000 (four zeros) as your PIN or passkey.
6. Your phone will conrm that pairing has succeeded and the
headset will begin ashing slowly in Blue.
NOTE: If the Pairing process is not completed within two minutes the
headset will return to Standby mode.
With some mobile phones, you may need to tap the CTRL button
to connect the headset to the phone after pairing is complete. The
scala rider TeamSet headset will automatically connect to the last
phone connected to the headset.
SET UP FOR BLUETOOTH GPS DEVICE
If you have a Bluetooth enabled GPS device and would
like to transmit navigation instructions and sounds
from the GPS device through the headset’s speakers,
please follow instructions described in section below
“TO PAIR THE scala rider TeamSet TO A Bluetooth GPS DEVICE”
If you want to use your mobile phone and your GPS device with the
scala rider TeamSet Driver’s unit headset, you should proceed as
follows:
1. Pair your GPS device to your mobile phone (Please consult your GPS
device’s User Manual for more information).
2. Pair your headset to the GPS device as described below.
NOTE: Not all Bluetooth enabled GPS devices allow connections to
Bluetooth headsets like the scala rider TeamSet. Please consult your
GPS device’s User Manual for more information.
TO PAIR THE SCALA RIDER TEAMSET TO A BLUETOOTH GPS
DEVICE:
1. Turn on your GPS device.
2. With the Driver’s unit headset turned OFF, press and hold
the CTRL Button until the Red and Blue Lights begin rapidly
alternating.
3. Search for Bluetooth headsets on your GPS device by following
the device’s instructions. Please consult your GPS device’s User
Manual for more information.
4. If your GPS device prompts for a PIN or Passkey enter 0000
(four zeros).
5. Your GPS device will conrm that pairing has succeeded. The
headset will begin ashing slowly in Blue.
6. If you wish to use a Bluetooth mobile phone to make and
receive calls through the headset, you must now pair your
mobile phone to your GPS device by following your GPS and/
or mobile phone’s instructions.
NOTE: If the Pairing process is not completed within two
minutes the headset will return to Standby mode.
PAIRING BETWEEN THE PASSENGER
AND DRIVER HEADSETS
The two headset units (Driver and Passenger units) are supplied facto-
ry paired. Therefore, you do not need to pair these devices. However,
if re-pairing is needed you may proceed as follows:
1. Make sure that both units are turned ON and close to each other.
2. Press the Intercom Buttons of both devices simultaneously for at least
10 seconds, the red Status Light of the passenger unit will light steadily.
3. If successful, the blue Status Light of the passenger unit will ash.
4. If pairing has failed, the red Status Light of the passenger unit will
turn o and you must repeat the procedure.
5
scala rider
®
TeamSet
™
ATTACHING THE CLAMP ON THE HELMET
Perform this procedure for both the driver and the passenger helmets.
The Helmet Clamp must be attached to the left side of the helmet. Once
attached, the headset unit can be mounted or released from the Helmet
Clamp at any time. If you wish to connect your MP3 player to you head-
set, please referrst to the assembly instructions listed in section: USING
THE MP3 PLAYER WITH YOUR HEADSET.
There are two methods that can be used in order to attach the Clamp
onto the helmet:
Standard Method: Recommended for most helmet types.
Glue Plate Method: Recommended for helmets
to which the standard method cannot be applied,
using the Glue Plate included in the box.
Standard Method
1. Use the enclosed Allen Wrench to loosen the two
screws on the Back Plate.
2. Slide the Back Plate between the internal
padding and the external shell of the helmet.
3. Adjust the clamp’s location so that the
microphone is located opposite center of
your mouth and then tighten the screws.
You may need to reposition the Clamp
repeatedly until you identify the best spot. The microphone
must be positioned vertically and not horizontally.
Glue Plate Method
You have the option to glue the Helmet Clamp onto your helmet, when
the above standard method cannot be used, or in case you prefer to
secure the Helmet Clamp with adhesive glue. This option has been
successfully used for a range of high end helmets.
NOTE: While we have no reason to believe that the gluing
option might negatively affect any helmet, Cardo
does not assume any responsibility to that affect, ir-
respective of its nature and circumstances. The Glue
Plate is offered as a free option that you may choose
to use at your own risk and subject to renouncement
of any future claims.
Caution: This process can be done only once!
1. Use the enclosed Allen Wrench to remove both Allen
screws and release the Helmet Clamp’s back plate.
2. Determine the location on the helmet where the Helmet Clamp
must be attached.
3. Adjust the Helmet Clamp’s location on the
Helmet so that the microphone is located
opposite the center of your mouth. You may
need to reposition the Clamp repeatedly until
you identify the best spot. The microphone must
be positioned vertically and not horizontally (Be sure to clean the
selected area prior to the gluing process as described in # 4 below).
4. Use the pre-moistened Towelette to clean the helmet area where
you want to install the Glue Plate. Allow to dry thoroughly.
5. Peel the foil cover from the Glue Plates’ adhesive pad.
6. Place the Glue Plate into position according to #3. Press rmly 15
seconds on all 3 parts of the Glue Plate.
7. The adhesive pad bonds to full strength over the next 24 hours.
Therefore it is recommended to not use the headset during this 24
hour period.
8. Fasten the Clamp to the Glue Plate using the Allen screws that were
previously removed.
6
scala rider
®
TeamSet
™
6
scala rider
®
TeamSet
™
English
POSITIONING THE SPEAKERS
Attach the speakers to the Velcro
Speaker A
Speaker B
Speaker A
Speaker B
Speaker B
Cable
inside your helmet opposite your
ears (short speaker cord for the left
ear [A] and the long speaker cord [B]
for the right ear). You may want to
use the supplied Velcro pad.
Using two speakers inside the
helmet may be prohibited in certain
jurisdictions. If this is the case, you
should tuck away the long corded
speaker underneath the helmet
padding as follows: Lead the speaker
cord [B] alongside the rim of the
padding to the right side and then back
to the left side, near speaker [A]. Then
place the speaker [B] underneath the
padding.
ATTACHING AND REMOVING THE
HEADSET FROM THE HELMET CLAMP
ATTACHING:
Slide the headset downwards along the
sliding panel until a clicking sound
indicates that the headset is locked in place.
Press here
to remove
REMOVING:
Your headset can be removed for
charging and storage by pressing your
nger gently against the tab and sliding
the headset up with the other hand.
We recommend that you remove the
headset from the helmet when not in use.
AUDIO SOURCES AND PRIORITIES
The dierent Audio Sources that are connected to the scala rider
TeamSet are prioritized as follows:
Highest: 1. Mobile phone audio (Incoming/outgoing calls) / GPS
device (GPS audio and navigation instructions)
2. Driver-to-Passenger Full Duplex Intercom Connec-
tion
Lowest 3. MP3 Connectivity
AUDIO SOURCES AND PRIORITIES – Passenger Unit
Passenger can also initiate intercom calls with drivers unit as well as
listen to music from his MP3 Player. Intercom call overrides the audio
from the MP3 player.
USING THE MP3 PLAYER WITH YOUR
HEADSET
Your scala rider TeamSet headset can be connected to an
MP3 player device by plugging it to the Helmet Clamp’s jack
with the MP3 cable.
At your option, you may further secure the MP3 cable by using the
7
scala rider
®
TeamSet
™
MP3 cable holder. For this purpose please proceed as follows:
1. Use the enclosed Allen Wrench to remove both Allen screws from
Helmet clamp and release the clamp’s back plate.
2. Place the MP3 cable holder on the
helmet clamp. Both pins on the
MP3 cable holder should be xed
into corresponding indentations on
clamp.
3. Place the Back Plate on top of the
MP3 cable holder and secure all
parts together using the Allen
screws that were previously removed, as shown in photo.
4. Attach the clamp and headset onto your helmet as described
previously in section “ATTACHING THE CLAMP ON THE HELMET”.
5. Attach the speakers to your helmet as described in section
”POSITIONING THE SPEAKERS”.
6. Connect the MP3 cable to your MP3 player device’s jack and the
other side to the helmet Clamp’s jack, inserting the cable through
the MP3 cable holder.
Make sure that the cable plug clicks
into place.
7. Tuck the MP3 cable into the hook of
the MP3 cable holder.
8. In order to use your MP3 player,
power on the headset to have it on Standby mode, ashing slowly
in Blue.
MP3 cable holder hook
NOTE: Operate the MP3 Player device by using its buttons (FF/REW/
PLAY/PAUSE).
Volume can only be adjusted through the MP3 Player. Any other
audio connection (Phone call/Intercom call) will automatically
mute the MP3 Player. The audio signal will return only when
headset is once again in Standby mode.
DRIVER’S UNIT FUNCTIONS
USING THE HEADSET
G E N E R A L F U N C T I O N S
DESIRED RESULT: REQUIRED ACTION:
Turn on the
headset
Press the CTRL Button steadily for at least 6 seconds.
Led indication: three blue ashes.
Audio feedback: Ascending tone (low-high).
Turn o the
headset
Press the CTRL Button steadily for at least 3 seconds.
Led indication: three red ashes.
Audio feedback: Descending tone (high-low).
Increase volume Tap the Volume Up Button
Decrease volume Tap the Volume Down Button
AGC (Automatic Gain Control): In addition to manual Volume Control,
the scala rider TeamSet will automatically increase and reduce its
volume according to ambient noise and driving speed.
INITIATING AND RECEIVING MOBILE
PHONE CALLS
Voice Recognition (VR)
The VR feature allows you to answer or reject incoming calls by voice
Control without having to remove your hands from the handlebars.
8
scala rider
®
TeamSet
™
English
The default mode of this feature is ON (enabled).
Each time you switch o and turn on the headset, the VR feature will
be automatically enabled.
To disable / enable the VR feature see phone functions below.
Note: The VR feature works well while driving up to 70km/h
or 44m/h with 3/4 helmet and up to 120km/h or 75m/h
with a closed full-faced helmet.
PHONE FUNCTIONS
Answer a call Tap the CTRL Button or speak loudly any word of
your choice.
Reject a call Tap the Intercom Button or remain silent for 15
seconds during an incoming call.
Terminate a call Press and hold the Intercom Button for 3
seconds when a call is in progress. For some
mobile phones you may need to press the
Control button to end the call.
Voice Dial During Standby, tap the CTRL Button and state the
name of the person you wish to call. This feature
is supported only by mobile phones that support
the Voice Dial feature.
Redial During Standby, tap the Intercom Button
Enable/Disable
voice command
feature
Long press the volume up and down buttons simul-
taneously until you hear a beep. The default status is
voice command enabled.
NOTE: If your Bluetooth mobile phone is paired to a Bluetooth GPS
device, not directly to the scala rider TeamSet, some of the above
Phone functions may not be compatible.
INTERCOM FUNCTIONS–Driver’s Unit
G E N E R A L F U N C T I O N S
DESIRED RESULT: REQUIRED ACTION:
Start using the intercom During standby, start talking loudly to
activate the feature
Terminate operation of
Intercom
Stop talking. The audio connection will be
terminated within 25 seconds.
Conference Call (add
passenger to an active call)
During an active phone-call, tap the
intercom button.
End Conference Call
(release passenger from a
conference call)
During a conference call, tap the intercom
button.
Note: In case the person on the other side of the intercom is not responding and
you start talking, 2 beeps will alert you that the other side is not available
STATUS LIGHTS
STATUS LIGHT STATUS
None Headset is o
Alternating Red/blue ashes Mobile phone/GPS Pairing mode
1 blue ash every 3 seconds Standby – No call is in progress
2 blue ashes every 3 seconds Call is in progress
1 red ash every 3 seconds Battery is low
2 red ashes every 3 seconds Low battery while a call is in progress
Solid red Charging
9
scala rider
®
TeamSet
™
PASSENGER’S UNIT FUNCTIONS
USING THE HEADSET
DESIRED RESULT: REQUIRED ACTION:
Turn on the headset Press the CTRL Button steadily for at least 3
seconds. Led indication: three blue ashes.
Audio feedback: Ascending tone (low-high).
Turn o the headset Press the CTRL Button steadily for at least 3
seconds. Led indication: three redashes.
Audio feedback: Descending tone (high-low).
Start using the Intercom During standby, start talking loudly to
activate the Intercom
Terminate operation of
Intercom
Stop talking. The audio connection will be
terminated within 25 seconds.
Enable/disable Always-on
Intercom
During standby tap the Control Button.
One tone = intercom enabled. Two tones =
intercom disabled.
Increase Intercom volume Tap the Volume Up Button
Decrease Intercom volume Tap the Volume Down Button
Note: In case the person on the other side of the intercom is not responding and
you start talking, 2 beeps will alert you that the other side is not available
STATUS LIGHTS
STATUS LIGHT STATUS
None Headset is o
One blue ash every 3 seconds Headset is on
Steady red (Charger is connected) Headset is being charged
Steady red (Charger is not
connected)
Headset in Intercom pairing
mode
SUPPORT
For additional information please visit our website at
www.cardosystems.com
FAQ: www.cardosystems.com/faq
or contact us at:
support@cardosystems.com
Phone: USA and Canada: + 1-800-488-0363
International: +4989 450 36819
NOTICES
Federal Communications Commission (FCC) Statement
15.21
You are cautioned that changes or modications not expressly approved by the
part responsible for compliance could void the user’s authority to operate the
equipment.
15.105(b)
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
10
scala rider
®
TeamSet
™
English
Operation is subject to the following two conditions:
1) this device may not cause interference and
2) this device must accept any interference, including interference that may cause
undesired operation of the device.
FCC RF Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for
an uncontrolled environment. End users must follow the specific operating
instructions for satisfying RF exposure compliance. This transmitter must not be
co-located or operating in conjunction with any other antenna or transmitter.
Industry Canada (IC) Statement
15.21
You are cautioned that changes or modications not expressly approved by the
part responsible for compliance could void the user’s authority to operate the
equipment.
15.105(b)
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the IC rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment o and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Operation is subject to the following two conditions:
1) this device may not cause interference and
2) this device must accept any interference, including interference that may cause
undesired operation of the device.
IC RF Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. End users must follow the specic operating instructions
for satisfying RF exposure compliance. This transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter.
European CE Notice
The scala rider TeamSet headset (the “Product”) is in conformity with the following
essential requirements of Council Directive 1999/5/EC (referred to as R&TTE
Directive): Articles 3.1a, 3.1.b and 3.2. The Product is manufactured in accordance
with Annex II of the above directive.
Declaration of Conformity (DOC)
The scala rider TeamSet headset is compliant with and adopts the Bluetooth
®
Speci-
cation 2.0 and has successfully passed all interoperability tests that are specied in
the Bluetooth
®
specication. However, interoperability between the device and other
Bluetooth
®
-enabled products is not guaranteed.
WAIVER AND GENERAL RELEASE
By using the scala rider TeamSet headset(s)–hereafter referred to in the singu-
lar–you will waive substantial legal rights including the right to sue. Please read
the following carefully before using the device. If you do not accept all terms of
this agreement, you should immediately return the product for a full refund. By
using the headset you agree to be bound to this agreement and forfeit the right
to sue.
Using a communication device while riding a motorcycle, scooter, moped, ATV, quad-
bike or any other vehicle or equipment, whether on land, water or air (jointly referred
to as “Vehicle”) requires your complete and undivided attention. Cardo Systems, Inc.,
including its Ocers, Directors, Aliates, Parent Company, Representatives, Agents,
Contractors, Sponsors, Employees, Suppliers and Resellers (jointly referred to as the
“Company” or “Cardo”) strongly advises you to take all necessary precautions and
remain alert to the trac, weather and road conditions if you choose to use the scala
rider TeamSet headset, including all derivative models irrespective of its commercial
name or branding (the “Device”), and stop your Vehicle on the roadside prior to
initiating or receiving calls. Any publications, advertisements, announcements or
similar notes that refer to using the Device while riding a Vehicle are solely intended
to address its technical capabilities and should not be misconstrued as if encouraging
users to operate the Device while actively involved in trac.
By way of purchasing this Device and not returning it for a full refund (see below), you
are irrevocably releasing, indemnifying from any liability, loss, claim and expense
11
scala rider
®
TeamSet
™
(including attorneys fees) and holding Cardo harmless for any bodily injuries, harm or
death as well as losses or damages in goods, to any Vehicles including your own, or to
any property or asset that belong to you or to third parties, any of which may result from
using the Device under any circumstances or conditions and irrespective of jurisdiction.
Cardo will not be responsible for any physical damages, irrespective of reasons, condi-
tions or circumstances, including malfunctioning of the Device, and all risks associated
with operating it rest solely and entirely with the user of this Device, irrespective of
whether the Device is used by the original purchaser or any third party.
Cardo hereby noties you that using this Device may also be in contravention to local,
federal, state or national laws or regulations, and that any use of the Device is entirely
at your sole risk and responsibility.
1. You, your heirs, legal representatives, successors or assigns, hereby voluntarily
and forever release, discharge, indemnify and hold harmless Cardo from any and
all litigation, claims, debts, demands, actions and liability which may arise, directly
or indirectly, from using the Device for any distress, pain, suering, discomfort,
loss, injury, death, damages to or in respect to any person or property however
caused, WHETHER ARISING FROM THE NEGLIGENCE OR OTHERWISE, and which
may hereafter accrue to you on some future date as a result of said use, to the
fullest extent permitted by law.
2. You fully understand and assume the risks in using the Device, including risk of
negligent acts or omissions by others.
3. You conrm that you are physically capable to use the Device and that you have
no medical conditions or needs that may infringe upon your abilities to do so in
a safe manner. You conrm that you are at least eighteen (18) years of age and
that you have been advised of the risks associated with the use of the Device.
You further conrm that you will not consume any alcohol that may aect your
alertness or any mind-altering substance, and will not carry, use or consume
these substances before or during the use of the Device.
4. You fully acknowledge our warnings and understand that: (a) risks and dangers
exist in using the Device while in trac, including but not limited to injury or
illness, strains, fractures, partial and/or total paralysis, death or other ailments
that could cause serious disability; (b) these risks and dangers may be caused
by the negligence of the manufacturers or its agents or any third party involved
in designing or manufacturing the Device; (c) these risks and dangers may arise
from foreseeable or unforeseeable causes. You hereby assume all risks and
dangers and all responsibility for any losses and/or damages, whether caused
in whole or in part by the negligence or other conduct of others, including the
Company.
5. You conrm that you have read this release of liability and fully understand its
terms and that you have given up substantial rights by not returning the Device
for a full refund (see refund option below).
Disclaimer of Warranty
CARDO DISCLAIMS ALL EXPRESS AND IMPLIED WARRANTIES WITH REGARD
TO THE ENCLOSED DEVICE, INCLUDING WITHOUT LIMITATION ANY IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE,
AND NON-INFRINGEMENT. THE DEVICE AND ITS ACCESSORIES ARE PROVIDED
“AS IS” AND “AS AVAILABLE” WITHOUT WARRANTY OF ANY KIND BEYOND
THOSE ASSUMED IN THE ENCLOSED MANUAL.
Limitation of Liability
IN NO EVENT SHALL CARDO BE LIABLE FOR ANY SPECIAL, INDIRECT, PUNITIVE,
INCIDENTAL, EXEMPLARY OR CONSEQUENTIAL DAMAGES, OR ANY DAMAGES
WHATSOEVER RESULTING FROM THE USE OF THE DEVICE, WHETHER BASED ON
BREACH OF CONTRACT, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY
OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. YOU
ACKNOWLEDGE AND AGREE THAT THE LIMITATIONS SET FORTH ABOVE ARE
FUNDAMENTAL ELEMENTS OF THIS AGREEMENT AND THE DEVICE WOULD NOT
BE PROVIDED TO YOU ABSENT SUCH LIMITATIONS. SOME STATE STATUTES MIGHT
APPLY REGARDING LIMITATION OF LIABILITY.
RETURN FOR FULL REFUND
IF YOU ARE UNWILLING TO ACCEPT AND AGREE TO THE ABOVE CONDITIONS,
YOU MAY RETURN THIS DEVICE TO CARDO FOR A FULL REFUND, PROVIDED
THAT YOU DO SO NO LATER THAN 7 BUSINESS DAYS FOLLOWING THE PUR-
CHASE OF THE DEVICE (proof of purchase required) AND SUBJECT TO THE
WRAPPING BEING INTACT. WHEN DOING SO, PLEASE REFER TO THIS SECTION.
BY NOT RETURNING THE DEVICE FOR REFUND WITHIN THE PERIOD PROVIDED,
YOU ARE EXPLICITLY IN AGREEMENT WITH THE ABOVE, AND RENOUNCE ALL
RIGHTS TO FUTURE CLAIMS AND DEMANDS AGAINST CARDO AS DEFINED
ABOVE.
www.cardosystems.com
12
scala rider
®
TeamSet
™
3 …

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Cardo-scala-rider-TeamSet

  • Ik heb sinds kort mijn Samsung Galaxy Young vervangen door een Note 3. Met de eerste kon ik altijd prima met de teamset via Bluetooth pairen en vervolgens telefoneren én muziek streamen (hoewel het geluid niet om over naar huis te schrijven was). Met de Note3 echter kan ik alleen nog maar telefoneren maar ik krijg met geen mogelijkheid muziek gestreamd. Volgens de beschrijving van de Note3 moet de teamset het A2DP protocol ondersteunen en volgens sommige websites doet hij dat ook.

    Iemand een een idee hoe (en met welke app) ik dit kan oplossen?

    Bij voorbaat dank
    RIck Gesteld op 2-4-2014 om 13:47

    Reageer op deze vraag Misbruik melden

    • Ik heb hetzelfde tussen een Scala Rider QZ en Samsung Galaxy S4. Een enkele keer lukt et wel, meestal niet. Geen idee waar hem dat in zit. Geantwoord op 13-7-2015 om 08:06

      Waardeer dit antwoord (1) Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Cardo scala-rider TeamSet bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Cardo scala-rider TeamSet in de taal/talen: Engels als bijlage per email.

De handleiding is 0,58 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Cardo scala-rider TeamSet

Cardo scala-rider TeamSet Gebruiksaanwijzing - Nederlands - 12 pagina's

Cardo scala-rider TeamSet Snelstart handleiding - Nederlands - 20 pagina's

Cardo scala-rider TeamSet Gebruiksaanwijzing - Deutsch - 12 pagina's

Cardo scala-rider TeamSet Gebruiksaanwijzing - Français - 12 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info