816467
45
Verklein
Vergroot
Pagina terug
1/52
Pagina verder
8988
Error message / error Possible cause Troubleshooting Personnel
High segment wear! Segment bonding is
too so
Use cutting wheels with
harder seg ments or reduce
feeding pressure
Operating personnel
Segments are too thin
in relation to the mo tor
capacity and feeding
pressure
Reduce the feeding
pressure , or use cutting
wheels with thicker
segments
Segment number is too
small
Use cutting wheels with seg-
ments, or reduce the feeding
pressure
The cutting wheel runs
out
Use a new cutting
wheel , have the old one
straightened , check the
cutting sha , use a new one
if necessary
The cutting wheel
deviates
Check the table guides,
replace if necessary
Abrasive aggregates Use cutting wheels with
harder seg ments
Feeding pressure is too
high
Reduce the feeding pressure
Cutting blade shows side
and radial run-out
Cutting blade is bent or
damaged
Have the cutting blade
straightened, solder the
segments to a new blade or
use a new blade
Manufacturer
Flange is polluted or
damaged
Clean or replace the flange Operating personnel
Motor sha is
bent
Replace the electric motor Qualified electricians
Zero performance when
cutting, cutting blade is
blunt
The cutting blade does
not match the material
Use a proper cutting blade Operating personnel
The cutting blade does
not match the machine
capacity
The cutting blade is too
hard
Diamond on the segment
are blunt
sharpen Specialist personnel
Suboptimal blade course Blunt segments sharpen Specialist personnel
Cutting blade is
overloaded
Use an appropriate cutting
blade
Operating personnel
Poor tension of cutting
blade
Return the cutting blade Manufacturer
Mounting bore of the
cutting blade is worn out
The cutting blade rotates
on the motor sha
Check the mounting flange,
replace if necessary
Manufacturer
The mounting bore must
be hollowed out and a ring
fitted in
Specialist personnel
Error message / error Possible cause Troubleshooting Personnel
The cutting blade is oxide-
coated
The cutting blade is
overheating, too little
cooling water
Check the cooling water Operating personnel
Lateral friction in the cut Lower the feed rate, pull the
material slowly
Cracks on steel core;
eccentrical wear of the
cutting blade
The cutting blade is too
hard
Use a soer cutting blade Operating personnel
Motor sha bearing Replace the motor sha
bearing
STEPS AFTER TROUBLESHOOTING
Aer completion of the troubleshooting and before switching on, follow the following steps:
1. Check for tightness all threaded joints previously detached.
2. Check proper installation of all previously removed protective devices and covers.
3. Make sure that all tools, materials and other equipment have been removed from the working zone.
4. Clean the working zone and remove any spilled substances such as liquids, processing materials or similar.
5. Make sure that all safety devices of the machine function properly.
45

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Carat T-4010 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Carat T-4010 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans, Pools, Deens, Zweeds als bijlage per email.

De handleiding is 4.81 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info