816467
12
Verklein
Vergroot
Pagina terug
1/52
Pagina verder
2322
ENGLISH
packaging on a regular basis. If necessary, renew or replace
conservation materials.
. TRANSPORT
ATTENTION!
Damage through improper transportation!
Improper transportation can result in considerable
damage of the machine and objects in the vicinity.
Before every transport:
- The cutter head must be locked.
- The cutter head must be lowered and locked.
- The cutting table must be secured by the table lock
(for table saw machines).
- The machine must be disconnected from power supply.
Due to two transport rollers, the machine can be
transported by one or two persons who can use transport
handles.
Instruction of using crane liing eyes
The machine is designed for crane transport by means of
the liing eye.
Always check the tighteness of the liing eyes before using
it to transport the machine. To avoid damage, also check
that the liing straps do not touch the motor when liing.
CAUTION:
Risk of injury due to improper handle when it is
transported by crane.
CAUTION:
Risk of injury by standing under the machine when
it is transported by crane.
CAUTION:
Risk of injury of falling material from the working
table, it is not allowed to have any material on working
table when it is transported.
Crane liing eyes MS400A / MS500A / MS600A
. INSTALLATION
5.1 Connection
Before connecting the machine to the power source,
make sure that:
- Voltage / phase of the power supply, match the date on
the type plate of the motor and machine.
- The power supply line is grounded according to the safety
provisions.
- The wire size of the extension cord is suicient, H07RNF
3x2.5 mm² up to 50m for 230V.
5.2 Mounting a diamond blade
To mount a new diamond blade or replace the used one,
proceed as follows:
1. Switch o the machine and interrupt the power supply
by pulling the mains cable from the mains outlet.
2. Loosen the screws on the diamond blade guard so as to
be able to remove the front half of the diamond blade
guard. For T-7010, aer loosening the screw on back
of blade guard, disconnect the quick release of water
connector on top of blade guard, then remove the blade
guard.
3. Loosen the nut of the motor sha and remove the outer
cutter flange.
4. Clean the cutter flange, nut and motor sha.
5. Check the parts for signs of wear.
6. Mount or replace the diamond blade. While doing so,
pay attention to the correct rotation direction of the
diamond blade and motor sha.
7. Replace the outer cutting flange on the motor sha.
8. Screw the nut onto the motor sha again and tighten it
firmly.
9. Replace the front half of the cutting wheel guard to
connect it with the rear half.
10. Tighten firmly the screws on the cutting wheel guard.
NOTE!
The arrow on the cutting wheel indicates
correct rotation direction.
NOTE!
The cutting wheel, irrespective of its position or
the position of the cutter head, may not touch the table!
5.3 Mounting the transport handles and wheels
Mount the transport handles at the appropriate places on
the base frame using the supplied washers (4x A8,4 ISO
7089) and the screws (4x M8x30 ISO 4017), the spring wash-
ers (4x A8 DIN 127) and the screws (4x M8x20 ISO 4017).
Do the same with the transport wheels. Mount the trans-
port wheels at the appropriate places on the base frame
using the supplied washers (4x A,8,4 ISO 7090), the spring
washers (4x A8 DIN127), the screws (4x M8x25 ISO 4017)
and the nuts (4x M8 ISO 4032).
Mounting the extension table
If you want to work with the extension table, proceed as
follows:
Insert the extension table into the lateral grommets on the
base frame and tighten it with the star grip screws
5.4 Fill the water tank
The water tank must be filled before the machine is
started. Use clear, clean water for this.
ATTENTION!
The water pump may not run without water,
otherwise it can be damaged.
. OPERATION
6.1 Intended working position of the operator
For table saw machines the operator takes position in
front of the machine to be able to slide the cutting table
forwards/backwards and to adjust the cutter head.
6.2 Start-up preparation
To safely use the machine as intended, the following
preconditions must be met:
- The machine stands firmly.
- The water tank is filled with clean, clear water.
- The machine has been checked for damage, loose screw
connections and integrity.
- The water supply is functional.
- Rotation direction arrows on the cutting wheel and guard
match.
- An appropriate cutting wheel must be installed, which
meets optimum conditions.
6.3 Start-up
The machine is switched on by the main switch. For this
purpose, press the green button to start
Aer the start, check the following:
The cooling water must be pumped to the cutting wheel
by the water pump in the suicient quantities and drain o
on both sides. If this is not the case, stop the machine im-
mediately! The motor is equipped with thermal insulation
activated when the temperature rises too high.
Wait approx. 30 minutes before restarting the machine
until the motor cools down
6.4 Cutting operation
6.4.1 Normal cutting in 90° position
When cutting in 90° position, the cutter head remains at a
fixed point. For adjustment, proceed as follows:
1. Switch o the machine -> the cutting wheel must stop
rotating!
2. Loosen the adjusting screw.
3. Set the cutter head in the desired position.
4. Tighten the adjusting screw -> check if the cutter head
is adjusted in height and make sure that it cannot
move.
5. Put the material to be cut onto the table (for table saw
machine position it directly at the material stop).
6. Check the position of the material using the angle stop.
7. Start the motor and the water pump and open the
water tap.
8. Put one hand on the cutter head handle.
9. Then slowly drag the cutter head without pressure over
the material on the table. The blade cuts the material.
NOTE!
The cutting wheel, irrespective of its position or
the position of the cutter head, may not touch the table!
12

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Carat T-4010 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Carat T-4010 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans, Pools, Deens, Zweeds als bijlage per email.

De handleiding is 4.81 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info