816477
40
Verklein
Vergroot
Pagina terug
1/104
Pagina verder
GB
40
load on the motor and increase wear on the mechanism. Repeat for the other guide tensioner.
7. Use the T-handle wrench on the arbor bolt and rotate it back and forth while tightening the drive
tensioner knob until there is just enough tension so that the drive wheel is turning the blade without
skidding. Then tighten a further 1/4 turn. Do not over tension.
8. Slide the drive wheel cover plate into position over the drive wheel and tighten the thumb knob.
9. The drive tension will need to be periodically adjusted because, over time, the drive wheel and blade
interface will wear. When this happens, tighten the drive tensioner slightly, just enough to keep the blade
from slipping.
WARNING: Never adjust the drive tension while the saw is running.
NOTE: Always replace the drive wheel with a new one when replacing a worn blade. The drive wheel and
blade wear together and should be replaced as a set.
Inspect the blade before use. It must not be cracked, warped or damaged in any way that would cause a hazard
in operation. Loose diamond segments can be ejected at high speed, causing possible injury. Always check
that the diamond segments are not under cut. If the diamond segments are thinner or nearly thinner than the
blade core, the kerf will be too tight fitting and could easily lead to kickback.
Inspect the blades for segment damage, or any other damage which could cause hazardous operation.
SPLASH GUARDS
The spring-loaded splash guards are useful to help contain slurry which splashes toward the back. The upper
guard has an over-center spring which will lock into the fully open position if it is pulled all the way back. The
lower guard has a clip which can be used to lock the guard in the fully open position.
WATER CONNECTION
Water is a basic requirement for this tool. The water also serves as a coolant to avoid the working surface of
the diamond segments from overheating. Water also keeps down dust and flushes away abrasive particles.
WARNING: Check all connections of the water feed system to ensure there are no leaks. Inspect hoses
and other critical parts which could deteriorate.
WARNING: The maximum water pressure should not exceed 70 psi (4 bar).
Note: Use a wet vacuum to collect cooling water if nearby objects could be damaged by water.
40

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Carat RS-3300 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Carat RS-3300 in de taal/talen: Nederlands, Duits, Engels, Frans, Deens, Zweeds, Noors als bijlage per email.

De handleiding is 2.95 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info