816452
24
Verklein
Vergroot
Pagina terug
1/92
Pagina verder
24
9. Then slowly slide the cutter head through the material
to be cut, without pressure. The cutting wheel then cuts
through the material on the table.
NOTE!
The cutting wheel, irrespective of its position or
the position of the cutter head, may not touch the table!
NOTE!
In emergency, press the red stop button on the
switch by the le hand.
Cutting method: 45° bevel cuts
The machine oers the possibility of performing 45° bevel
cuts. To perform 45° bevel cuts, proceed as follows:
1. Switch o the machine -> the cutting wheel must stop
rotating!
2. Loosen the star grip screws on the bridge on both sides
of the machine.
3. Pivot the complete cutter head including the bridge into
the desired position. Orientate yourselves on the lateral
scale.
4. Tighten again the star grip screws.
5. Then loosen the adjusting screw.
6. Adjust the depth stop and x this setting.
7. Put the material to be cut on the table. Check the
material’s position using the angle stop.
8. Start the motor and the water pump and open
the water tap.
9. Grab the cutter head’s chain driven hand crank with
the right hand and the transport handle on the frame
with the le hand.
NOTE!
In emergency, press the red stop button on the
switch by the le hand.
NOTE!
The cutting wheel, irrespective of its position or
the position of the cutter head, may touch neither the
table, nor the back square!
To bring back the guiding bridge and the cutter head to the
90° position aer the cutting operation, proceed as follows:
1. Switch o the machine -> the cutting wheel must
stop rotating!
2. Loosen the star grip screws on the bridge on both
sides of the machine.
3. Pivot the complete cutter head including the bridge
into the desired position. Orientate yourselves on the
lateral scale.
4. Firmly tighten again the star grip screws.
NOTE!
Hold firmly the cutter head with the hand
in the 90°¬ position. Tightening the nut can turn the
square back so that the angle of the cutter head is
not exactly 90°.
NOTE!
The cutting wheel, irrespective of its position
or the position of the cutter head, may not touch the
cutting table!
6.4.2 Water supply
Heavily polluted water decreases the service life of the
water pump and cutting wheel.
For frequent use, change water several times a day, and
collect, lter and dispose of the cutting mud
Clean the suction strainer of the water pump every time
the water is changed
6.5 Stop cutting operation
Use the red stop switch on the motor to stop the machine.
. MAINTENANCE & CLEANING
Before performing any maintenance, make sure the
machine is disconnected from electrical power.
For long-term quality, please perform the following
maintenance actions aer using the machine
- Visually inspect the entire machine.
- Clean the ange and blade mounting.
- Clean engine (housing + cooling fans), water tank, water
pump, water pump lter, water hoses and nozzles, table
guide rails, table wheels.
- Make sure all bolts and screws are tightened.
Before using the machine, make sure that all the above
actions have been performed.
een korte rustpauze.
. DISPOSAL
If no return or disposal agreement was made, send the
dismantled components for recycling:
- Scrap metal parts.
- Hand over plastic parts for recycling.
- Dispose of other components assorted according to
material characteristics.
EU countries only
Electric waste is recyclable and must not be
disposed of in the household waste!!
According to the European directive 2012/19/EU on
electrical and electronic waste and version transposed
into national law, used power tools must be collected
separately and sent for recycling in an environmental-
friendly manner.
24

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Carat CARACOUP 104 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Carat CARACOUP 104 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans, Pools, Deens, Zweeds als bijlage per email.

De handleiding is 3.7 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info