562773
35
Verklein
Vergroot
Pagina terug
1/48
Pagina verder
35
Problem Possible cause Solution
Subwoofer
does not turn
on
1. The power cable is not connected from the socket to the
subwoofer
Check connection
2. The power has not been turned on Switch to “ON”
3. The switch for automatic switching on is not in the “ON”
position or the “AUTO” or “AUTO HIGH” positions
Check switch setting
4. The subwoofer is not connected with the amplifier (re-
ceiver) through its speaker outlet (High Level) or subwoofer
outlet (cinch) cable
Check connection
5. Defective signal line (cinch) Test with another cinch cable and change cable if necessary
6. The volume of the amplifier has been set too low
Increase volume level to test
7. With a “Dolby Digital” receiver (amplier): the receiver is
not set for subwoofer operation (operating method “Small”
or “ActiveSub = On”)
Check operating mode
8. The outlet level on the amplifier is set too low for the
subwoofer outlet (cinch outlet)
Increase the outlet level of the amplifier
9. The microfuse in the subwoofer has blown (fused) Get a specialist to change the microfuse
Subwoofer
does not
switch off
1. Switch for automatic switching on (Standby) set to “ON” Switch to “Auto” or “OFF”
2. Constant humming at inlet of subwoofer
Use a shorter signal line from the amplifier to the subwoofer or remove any possible sources of
interference (see “Subwoofer hums”)
Subwoofer
hums
1. Signal line from amplifier to subwoofer too long
Use shorter signal line
2. Signal line used is not fault-protected or the protection
has been damaged (defective)
Change signal line for a fault-protected line
3. Ground loop (ripple pickup) generated A ground loop can be generated when two or more devices connected via a signal line (cinch)
are plugged into separate sockets (e. g. amplifier and computer). All devices connected to the
amplifier should be plugged into the same multiple socket outlet
4. Another piece of equipment on the same circuit has no
interference suppression (e. g. fridge)
Switch off possible sources of interference to test; unplug the device concerned to see if the
humming noise disappears or connect the source of interference to a different circuit (L1, L2
or L3). (Where necessary take advice from your electrician.) Insert a special “ferrite common
mode lter” (available from specialist retailers) between the amplier and the subwoofer to
eliminate the humming. Disconnect and rotate the mains plug to reduce the so-called ripple
voltage. (Particularly important if the amplifier is not earthed)
Subwoofer
does not
respond to
remote control
1. The battery is flat Change the battery
2. The remote control is not registered on the subwoofer Turn the subwoofer off, wait for 30 seconds then turn it back on. Activate the remote control
and press the “- Phase”, “+ Phase” and “Power/Auto” buttons in quick succession. The sub-
woofer and the remote control are now synchronised
ENG
35

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Canton SUB8.2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Canton SUB8.2 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans, Pools, Zweeds als bijlage per email.

De handleiding is 1,08 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info