709292
210
Verklein
Vergroot
Pagina terug
1/231
Pagina verder
Troubleshooting
210
Invalid operation
- The following are not valid operations and cannot be performed.
Trying to add a shot mark to a frame that already has one.
Trying to add an $ mark and a % mark to the same clip.
•Pressing the REC button when no cards are inserted in the camcorder.
Management file error
- Cannot record because the camcorder cannot write to the file control information. This may occur if the files on the
card were accessed using another device. Save your clips (A 151) and initialize the card (A 35).
May not be possible to record clips on this media
- The card selected for recording has a Speed Class rating lower than 10. Use a recommended card (A 33).
Media full
-The S D card is full. Replace the card or delete some recordings (A 140, 182) to free some space on the card.
Media is almost full
- The amount of available space on the SD card is low. Replace the card or delete some recordings (A 140, 18
2) to free
some space.
- The amount of available space on SD card A and SD card B combined is low. Replace the card that is not selected.
Media is not supported
- 512 MB or smaller SD cards cannot be used with the camcorder. Use a recommended card (A 33).
Memory card is write-protected
- The LOCK switch on the SD card is set to prevent accidental erasure. Change the position of the LOCK switch.
Number of clips already at maximum
- The card selected for recording already contains the maximum number of clips (999 clips). Replace the card.
Number of Shot Marks at maximum
-The shot mark could not be added because the clip already contains 100 shot marks.
Recorded at 50.00 Hz/59.94 Hz SD Card A / SD Card B: Recommend checking the data and initializing
- The card contains clips that were recorded using a system
frequency different from the one currently used by the
camcorder. Save the content of the card if necessary and initialize the card with this camcorder (A 35).
Recording was stopped.
- The file control information is corrupted or there was an encoder error. Turn the camcorder off and then on again.
Then, remove the card being used and reinsert it. Alternatively, replace the card. If this does not solve the problem,
consult a Canon Service Center.
SD Card A / SD Card B: Check the data.
- Cannot access the card. Check the card and make sure it is inserted correctly.
- A card error occurred. The camcorder cannot record or display the image. Try removing and reinserting the card, or
use a different card.
-You inserted a MultiMedia Card (MMC) into the camcorder. Use a recommended SD card (A 33).
- If after the message disappears,
or appears in red, perform the following: Turn off the camcorder and remove
and reinsert the card. If
6
or
7
turns back to green you can resume recording/playback. If the problem persists,
save your clips (A 151) and initialize the card (A 35).
SD Card A / SD Card B: Recommend checking the data and initializing
- The card cannot be used for any of the following reasons. Save your clips (A 151) and initialize the card (A 35).
•A problem has occurred with the card.
The camcorder cannot read the data on the card.
•The card was initialized using a computer.
•The card is partitioned.
-The card was initialized using a camcorder with a different firmware version. To be able to record on the card, save the
recordings it contains and then initialize it using this camcorder.
SD Card ASD Card B / SD Card BSD Card A Switched
- The camcorder switched to recording on the other card after you pressed the SLOT SELECT button or automatically
due to relay recording.
SD Card ASD C
ard B / SD Card BSD Card A Will switch in a moment
-The selected card is almost full so the camcorder will switch to recording on the other card in approximately 1 minute
(relay recording).
Some clips require data recovery.
-The power may have been suddenly turned off or the card may have been removed while the camcorder was
recording. As a result, one or more clips contain corrupted data. You can try to recover the clips (A 37).
210

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Canon XF705 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Canon XF705 in de taal/talen: Engels als bijlage per email.

De handleiding is 17,49 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Canon XF705

Canon XF705 Gebruiksaanwijzing - Nederlands - 229 pagina's

Canon XF705 Gebruiksaanwijzing - Deutsch - 238 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info