596283
10
Verklein
Vergroot
Pagina terug
1/19
Pagina verder
Basic Wireless E-TTI. Autoflash O~eration
(5)
Taking the picture and
flash
confirmation
When you press the shutter but-
ton
con~pletely,
a
wirrlcss signal
is transmitted
to
the slave, then
the slave fires a preflash and then
the main flash when the picture is
taken.
The subject's flash cxposurc reading
is obtained with the
preflash and
used to set the main flash output.
Wireless flash photography is there
-
by executed with an optimum flash
ou1put.
When the correct flash exposure is
obtained, the
ST-E2's flash confir
-
mation lamp lights for about 3 sec.
immediately after the flash fires. If
it does not light, the picture might
be underexposed. In this case, use a
larger aperture or place the slave
28
closer to the subject and repeat
steps
(2) to
(5).
With the EOS
-
3, the model-
Ing flash can be fired to see
B
,'
the lighting effects before
the piclure is taken. See
page 32.
The slave must be properly
positioned to receive the
wireless transmission.
After the picture is taken.
the slave's operation result
is displayed on the slave's
display panel.
If
the slave is in the SE
(Save Energy) mode, press-
ing the
ST-E2's test trans-
mission button will cancel it.
When you press the shutter
button halfway and activate
the camera's exposure
meter, the ST
-
E2 cannot be
used to cancel the slave's
SF:
mode or to execute a test
transmission. The camera's
exposure meter must turn
off (viewfinder's
exposure
setting display turns off)
before the SE mode can be
canceled or a test transmis-
sion executed.
AF
-
assist beam
Under low-light or low-contrast
conditions, the
ST-E2's
AF
-
assist beam
is
emitted to assist
autofocusing.
The
AF
-
assist
beam is compatible with the
EOS-3's Area AF. The AF-assist
beam's effective range
is
about
0.6
meter to
10
meters
at
the
center and
0.6
meter to
5
meters along the periphery.
The ST-E2's AF
-
assist bran>
can
he
emitted only while the ST-E:! is
attached to the EOS-3. In
the
case
of
EOS
cameras with a built
-
in AF
-
assist beam emitter, the beam will
be emitted by the camera.
The slave's AF
-
assist beam is not
emitted (except when the flash is
ready).
44
To prevent overheating, limit
the number of consecutive
wireless transmissions to
50.
After
50
consecutive wireless
transmissions, allow the ST
-
EP
to rest for
10
minutes.
COPY
10

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Canon Speedlite Transmiter ST-E2 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Canon Speedlite Transmiter ST-E2 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,85 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info