809437
102
Verklein
Vergroot
Pagina terug
1/254
Pagina verder
Setting the Time Code
102
Selecting Drop or Non-Drop Frame
When the frame rate is set to 59.94P, 59.94i or 29.97P, you can select between a drop frame (DF) or non-drop
frame (NDF) time code, depending on how you plan to use your recordings.
With all other frame rates, the time code is set to non-drop frame (NDF) and cannot be changed.
Select > [
B
System Setup] > [Time Code DF/NDF] > Desired option.
The time code display will change depending on the setting. When you select [DF], the time code will appear
as [00:00:00.00]; when you select [NDF], it will appear as [00:00:00:00].
About the time code display
A letter may appear next to the time code depending on the setting/status. Refer to the following table.
NOTES
NOTES
The frames value of the time code runs from 0 to 23 (frame rate set to 23.98P or 24.00P), from 0 to 24 (frame
rate set to 25.00P, 50.00i or 50.00P), or from 0 to 29 (all other frame rates).
When slow & fast motion recording/frame recording/interval recording is activated, you cannot select the [Free
Run] running mode. Conversely, when pre-recording is activated, [Free Run] is set automatically and cannot be
changed.
When slow & fast motion recording/frame recording/interval recording is activated, the time code signal will not
be output from any of the terminals.
When you mix drop frame and non-drop frame time codes, there might be a discontinuity in the time code at
the point where the recording starts.
When you are using the [Free Run] running mode, the time code will continue running as long as the built-in
backup battery has some charge left, even if you disconnect all other power sources.
If you set an assignable button to [Time Code] (A125), you can press the button to open the
[B System Setup] menu page with the time code settings.
Setting the User Bit
You can set a user bit composed of the date or the time of recording or an identification code consisting of
8 characters in the hexadecimal system. There are sixteen possible characters: the numbers 0 to 9 and the
letters A to F.
The user bit is recorded with clips and can be output from the TIME CODE terminal/HDMI OUT terminal. It can
be used freely to categorize and manage recordings or to keep additional information about them.
1Select > [
B
System Setup] > [User Bit Type] > [Setting], [Date] or [Time].
If you select [Time] or [Date] the rest of the procedure is not necessary.
2Select [Change].
To reset the user bit to [00 00 00 00], select [Reset] instead.
3 Enter the user bit using the data entry screen (A25).
Letter Description
RThe time code mode is set to [Regen.].
PThe time code mode is set to [Preset] and the running mode is set to [Rec Run].
FThe time code mode is set to [Preset] and the running mode is set to [Free Run].
EThe time code signal is coming from an external source.
No letter Time code during clip playback.
102

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Canon EOS R5 C bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Canon EOS R5 C in de taal/talen: Engels als bijlage per email.

De handleiding is 13.28 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

loading

Andere handleiding(en) van Canon EOS R5 C

Canon EOS R5 C Gebruiksaanwijzing - Deutsch - 263 pagina's

Canon EOS R5 C Gebruiksaanwijzing - Deutsch - 815 pagina's

Canon EOS R5 C Gebruiksaanwijzing - English - 797 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info