683260
252
Verklein
Vergroot
Pagina terug
1/255
Pagina verder
Digital Cinema Camera
Instruction Manual
Firmware ver. 1.0.7.1.00 (Z[)
ver. 1.0.5.1.00 (])
ver. 1.0.1.1.00 (qr)
PUB. DIE-0494-001A
2
Important Usage Instructions
WARNING
TO REDUCE THE RISK OF ELECTRIC SHOCK AND TO REDUCE ANNOYING INTERFERENCE, USE THE
RECOMMENDED ACCESSORIES ONLY.
COPYRIGHT WARNING
Unauthorized recording of copyrighted materials may infringe on the rights of copyright owners and be
contrary to copyright laws.
FCC NOTICE
Digital Cinema Camera, EOS
C700 Systems.
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
NOTE: This equipment has been tested and
found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide
reasonable protection against harmful
interference when the equipment is operated
in a commercial environment. This equipment
generates, uses, and can radiate radio
frequency energy and, if not installed and used
in accordance with the instruction manual, may
cause harmful interference to radio
communications. Operation of this equipment in
a residential area is likely to cause harmful
interference in which case the user will be
required to correct the interference at his own
expense.
Do not make any changes or modifications to
the equipment unless otherwise specified in the
manual. If such changes or modifications should
be made, you could be required to stop
operation of the equipment.
Only for European Union and EEA (Norway, Iceland and Liechtenstein)
These symbols indicate that this product is not to be disposed of with your household
waste, according to the WEEE Directive (2012/19/EU), the Battery Directive (2006/66/EC)
and/or national legislation implementing those Directives.
If a chemical symbol is printed beneath the symbol shown above, in accordance with the
Battery Directive, this indicates that a heavy metal (Hg = Mercury, Cd = Cadmium, Pb = Lead) is present in
this battery or accumulator at a concentration above an applicable threshold specified in the Battery
Directive.
This product should be handed over to a designated collection point, e.g., on an authorized one-for-one
basis when you buy a new similar product or to an authorized collection site for recycling waste electrical
and electronic equipment (EEE) and batteries and accumulators. Improper handling of this type of waste
could have a possible impact on the environment and human health due to potentially hazardous
substances that are generally associated with EEE. Your cooperation in the correct disposal of this product
will contribute to the effective usage of natural resources.
For more information about the recycling of this product, please contact your local city office, waste
authority, approved scheme or your household waste disposal service or
visit www.canon-europe.com/weee
, or www.canon-europe.com/battery.
CAN ICES-3(A)/NMB-3(A)
WARNING
This is a class A product. In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.
3
Trademark Acknowledgements
SD, SDHC and SDXC Logos are trademarks of SD-3C, LLC.
Canon is an authorized licensee of the CFast 2.0 trademark, which may be registered in various
jurisdictions.
Microsoft and Windows are trademarks or registered trademarks of Microsoft Corporation in the United
States and/or other countries.
Apple and macOS are trademarks of Apple Inc., registered in the U.S. and other countries.
The Apple ProRes codec module is used under license from Apple Inc.
Avid and Media Composer are trademarks or registered trademarks of Avid Technology, Inc. or its
subsidiaries in the United States and/or other countries.
IDX, the IDX logo, V-mount are trademarks or registered trademarks of IDX Company, Ltd.
Wi-Fi is a registered trademark of the Wi-Fi Alliance.
Wi-Fi Certified, WPA, WPA2, and the Wi-Fi Certified logo are trademarks of the Wi-Fi Alliance.
WPS as used on the camera’s settings, onscreen displays and in this manual signifies Wi-Fi Protected Setup.
The Wi-Fi Protected Setup Identifier Mark is a mark of the Wi-Fi Alliance.
JavaScript is a trademark or registered trademark of Oracle Corporation, its affiliates or subsidiaries in the
United States and other countries.
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of
HDMI Licensing Administrator, Inc. in the United States and other countries.
DaVinci Resolve™ is the trademark of Blackmagic Design Pty Ltd.
Other names and products not mentioned above may be trademarks or registered trademarks of their
respective companies.
This device incorporates exFAT technology licensed from Microsoft.
This product is licensed under AT&T patents for the MPEG-4 standard and may be used for encoding
MPEG-4 compliant video and/or decoding MPEG-4 compliant video that was encoded only (1) for a personal
and noncommercial purpose or (2) by a video provider licensed under the AT&T patents to provide MPEG-4
compliant video. No license is granted or implied for any other use for MPEG-4 standard.
ANY USE OF THIS PRODUCT OTHER THAN CONSUMER PERSONAL USE IN ANY MANNER THAT
COMPLIES WITH THE MPEG-2 STANDARD FOR ENCODING VIDEO INFORMATION FOR PACKAGED
MEDIA IS EXPRESSLY PROHIBITED WITHOUT A LICENSE UNDER APPLICABLE PATENTS IN THE MPEG-2
PATENT PORTFOLIO, WHICH LICENSE IS AVAILABLE FROM MPEG LA, L.L.C., 250 STEELE STREET,
SUITE 300, DENVER, COLORADO 80206.
4
Highlights of the Camera
The Canon Digital Cinema Camera EOS C700 / EOS C700 PL / EOS C700 GS PL / EOS C700 FF /
EOS C700 FF PL has been designed to meet the demanding needs and highest expectations of industry
professionals. The following are just some of the many features that will help turn your creative vision into reality.
4K Recording System with Cinema Quality
Advanced CMOS sensor
The camera features a Super 35mm-equivalent
CMOS sensor (
Z[
), a Super 35mm-
equivalent CMOS sensor with global electronic
shutter (
]
) or full-frame CMOS sensor
(
qr
). With the sensor’s effective
pixel count of 8.85 megapixels (
Z[
]
) or 18.69 megapixels (
q
r
) and the Triple DIGIC DV5 imaging
engine, this camera delivers superb images.
Because the camera uses oversampling to produce
4K video from the 18.69-megapixel sensor
(
qr
), the image quality is
outstanding. Thanks to Canon’s high sensitivity and
low-noise technology, the camera can record at a
wide range of sensitivity settings, from ISO 160 to
ISO 25600
1
. Using one of the Canon Log gamma
curves you can make the most of the image
sensor’s characteristics to obtain a very wide
dynamic range.
1
The ISO speed range depends on the model and can be
extended.
Interchangeable lenses
With some models featuring different lens mounts
and shutter mechanisms, the camera offers the
freedom to use the lens you want in order to achieve
exactly the look you want. With the models featuring
an EF lens mount (
Zq
), you can use over
100 high-quality lenses from Canon’s EF and EF
Cinema lens series. Whereas the models featuring a
PL lens mount (
[]r
) let
you use a variety of industry-standard PL lenses.
Using the global shutter model (
]
), you
can shoot fast-moving subjects without worrying
about rolling shutter distortions or artifacts. And
using compatible broadcast lenses
2
and EF Cinema
lenses (A 240), you will be able to control the
aperture and zoom using the camera
3
. The camera
also supports the use of anamorphic lenses
(A 122).
2
The optional MO-4E or MO-4P B4 Mount Adapter is
required.
3
Depending on the lens used, you may need to connect
the 12-pin camera interface cable to the camera.
Choose your format – XF-AVC or ProRes
Using the XF-AVC format, the camera can use two
codecs (H.264 Intra-frame and H.264 Long GOP) so
you can select the video configuration from YCbCr
4:2:2, 10 bit, RGB 4:4:4, 10 or 12 bit, or YCbCr
4:2:0, 8 bit, to suit your creative needs. Using
Apple’s ProRes format, you have the choice of the
10-bit ProRes 422 HQ codec, 12-bit ProRes 4444
codec and 10-bit ProRes 422 codec.
RAW recording and output exceeding 4K
You can use a recorder docked with the camera
(A 21) to record RAW video at over 4K
4
. At the
same time, you can apply a LUT that meets the
ACES standard to video output from the MON.
terminals or the HDMI OUT terminal to use this video
output for on-set color grading (A 22).
4
The resolution of RAW recordings depends on the model.
Recording media
The camera features two CFast card slots and an
SD card slot. It records main recording clips
(XF-AVC or ProRes) on the CFast cards. When you
insert two CFast cards in the camera, the camera
can record simultaneously on both cards (double
slot recording), or it can switch automatically to
recording on the other CFast card when a CFast
card becomes full (relay recording) (A 52). In
addition to the main recording, you can activate the
simultaneous sub recording (A 71). Sub recording
clips can be recorded on the CFast card (XF-AVC
Intra) or on the SD card (XF-AVC Proxy).
Operability and Adaptability
Expandable modular design
The sturdy camera body was designed with ease of
use and expandability in mind. It features a multitude
of screw holes of different diameters on its top and
bottom plates to offer a large number of options for
attaching additional accessories to the camera.
Using the optional EVF-V70 OLED Electronic
Viewfinder (17 mm (0.7 in.), 1920x1080 pixels/
approx. 6.22 million dots), OU-700 Remote
Operation Unit, SU-15 Shoulder Support Unit and
SG-1 Shoulder Style Grip Unit, you can quickly
optimize the camera for one-person operation or for
team operation from both sides, depending on your
needs (A 38).
The camera offers assignable buttons and a
customizable USER screen (using the screen
buttons) that you can customize to your preferences
from a large number of convenient functions
(A 127). Optional accessories offer additional
assignable buttons. Assign functions that you use
often to the assignable buttons you find most
convenient to personalize the camera to your needs
and preferences.
5
Power options
You can power the camera using commercially
available V-mount batteries or power sources
connected to the DC IN 12V terminal (XLR 4-pin
jack) (A 26). The camera also offers power outputs
(24 V DC, 12 V DC or D-Tap) to supply power to
connected accessories (A 28).
Remote operation
You can attach the optional RC-V100 Remote
Controller to the camera to control it from a
distance. The remote controller lets you control a
wide range of camera settings (A 123).
Connect the camera to a network (Wi-Fi
5
or wired)
to operate it remotely from a network device using
the Browser Remote application (A 170). Browser
Remote lets you check the live view image from the
camera, adjust main camera settings and change
the metadata embedded with XF-AVC clips.
5
The optional WFT-E6 or WFT-E8 Wireless File Transmitter
is required.
Versatile Artistic Expression
Slow & fast motion (A 68)
Change the shooting frame rate to create a slow
motion effect or fast motion effect.
Custom picture settings
Select one of the preset color settings or set the
combination of gamma curve, color space and color
matrix that you wish to use. Then, you can adjust a
number of other image-related parameters in detail.
With wide color space options such as BT.2020
Gamut and Cinema Gamut, and the Canon Log 3
gamma curve, which keeps the characteristics of
the Canon Log gamma while expanding the
dynamic range, you can be sure that the camera
covers your creative needs.
Other Functions
IP streaming and FTP transfer
Connect the camera to a network (Wi-Fi
6
or wired)
to stream live transmissions or breaking images via
IP and to transfer sub recordings (XF-AVC Proxy
clips) from the SD card to a remote server using the
FTP protocol.
6
The optional WFT-E6 or WFT-E8 Wireless File Transmitter
is required.
Software for aiding production workflow
Canon XF Utility (A 161) lets you copy the XF-AVC
clips you recorded from your recording media to a
computer, play back the clips and organize them.
Cinema RAW Development (A 161) can develop
RAW data and export it as a standard file type such
as DPX or OpenEXR. You can also import an EDL to
recreate an edit created on NLE software. This helps
make a smooth transition to the color grading
process.
Dual Pixel CMOS AF and autofocus functions
(
Zq
)
The camera features Dual Pixel CMOS AF
technology, which covers almost 80% of the
recording area, and offers various autofocus
functions (A 89): continuous AF, one-shot AF (to
use autofocus only when you choose) or
AF-boosted MF (to let you focus manually most of
the way and let the camera finish focusing
automatically). Using AF-boosted MF the camera
does not perform unreliable focus adjustments,
resulting in a smoother focusing operation than with
continuous AF.
The camera also features face detection (A 96),
tracking of moving subjects (A 97) and the Dual
Pixel Focus Guide function (A 90), a visual, intuitive
guide that you can use to check if the image is in
focus. This can be very helpful to ensure you always
get amazingly sharp video when shooting with
resolutions 4K and higher.
Assistance functions
The camera offers a number of assistance functions,
such as peaking and magnification (A 90),
onscreen markers (A 98), zebra patterns (A 99),
B&W image (A 195), false color display (A 100)
and waveform monitor (A 115) that you can
display on an optional viewfinder or on external
monitors connected to the MON. terminals or HDMI
OUT terminal. When using a logarithmic gamma
curve, you can also apply a LUT (A 155) for easier
monitoring.
Other helpful features
Five levels of ND filter (A 78).
Z[qr
Flash band
correction (A 75).
In-camera correction for peripheral illumination
and chromatic aberration (A 47).
Built-in level (electronic horizon) (A 40).
Illuminated buttons for night time or black-out
operation.
Monaural built-in microphone for note taking.
Customizable onscreen displays (A 139).
Three sets of customizable My Menu submenus
(A 35).
Menu settings file that can be saved in the camera
or on an SD card to restore all the menu settings
or replicate them perfectly on another C700 series
camera (A 140).
Improved clip name format with more information
for easier identification and organization of clips
(A 62).
Metadata and geotagging (A 118, 120, 180).
6
1. Introduction 11
About this Manual 11
Conventions Used in this Manual 11
Supplied Accessories 12
Names of Parts 13
Microphone Holder 18
Handle Unit 18
Clamp Base 19
EVF-V70 OLED Electronic Viewfinder
(optional) 20
4K Workflow Overview 21
Color Grading with the ACES Workflow 22
2. Preparations 23
Preparing the Backup Battery 23
Removing an Extension Module 23
Inserting the Lithium Button Battery 24
Installing an Extension Module 24
Preparing the Main Power Supply 26
Acceptable Power Sources 26
Using a Battery 26
Using the DC IN 12V Terminal 27
Checking the Camera’s Power Levels 27
Power Outputs 28
Turning the Camera On and Off 28
Date, Time and Language Settings 29
Setting the Date and Time 29
Changing the Language 29
Changing Camera Settings with the Screen
Buttons 30
Using the Menus 32
Selecting an Option from the Camera Menu 32
Selecting an Option from the Monitoring Menu 33
Using the Customized Submenu (My Menu) 35
Preparing the Camera 38
Shooting Configurations 38
Attaching the Handle Unit 40
Using a Tripod 40
Using the Optional EVF-V70 OLED Electronic
Viewfinder 41
Attaching the Microphone Holder 43
Preparing the Lens 44
In-Camera Lens Correction 47
Preparing Recording Media 48
Compatible Recording Media 48
Inserting a CFast Card 49
Removing a CFast card 49
Inserting and Removing an SD Card 50
Initializing Recording Media 51
Switching Between the CFast Card Slots 52
Relay Recording and Double Slot Recording 52
Checking the Remaining Recording Time on
Recording Media 53
Recovering Clips 53
Adjusting the Black Balance 54
3. Recording 55
Recording Video 55
Recording 55
Onscreen Displays on the HOME Screen 57
Onscreen Displays on the Shooting Screen 59
Setting the Clip File Name 62
Using the Fan 64
Video Configuration: Video Format, Sensor Mode,
System Frequency, Frame Rate, Resolution
and Bit Rate 65
Selecting the Main Recording Format 65
Selecting the Sensor Mode 65
Selecting the System Frequency 65
Selecting the Frame Rate 65
Selecting the Resolution and Color Sampling
Settings 66
Selecting the Bit Rate 66
Slow & Fast Motion Recording 68
Simultaneous Sub Recordings 71
Changing Main Camera Functions with the FUNC
Button 73
Using the Direct Setting Mode 73
Shutter Speed 74
Changing the Shutter Speed Mode and Value 75
ISO Speed/Gain 76
Changing the ISO Speed or Gain Value 77
Using the Control Dial 77
ND Filter 78
Table of Contents
7
Adjusting the Aperture 79
Manual Aperture 80
Momentary Automatic Aperture - Push Auto
Iris 81
Automatic Aperture 81
Exposure Compensation - AE Shift 82
Light Metering Mode 82
Gamma Curve and Main Color Settings 84
Preset Color Settings 84
White Balance 86
Selecting the White Balance Mode/Setting 86
Auto White Balance (AWB) 87
Registering a Custom White Balance 87
Adjusting the Color Temperature or CC Value 88
Renaming User-Set White Balance Settings 88
Adjusting the Focus 89
Manual Focus 90
Zq
One-Shot AF 92
Zq
AF-Boosted MF 93
Zq
Continuous AF 94
Zq
Changing the AF Frame Size and
Position 95
Zq
Face Detection 96
Zq
Tracking a Specific Subject 97
Onscreen Markers, Zebra Patterns and False
Color 98
Displaying Onscreen Markers 98
Displaying Zebra Patterns 99
Using the False Color Display 100
Setting the Time Code 101
Selecting the Time Code Mode 101
Selecting Drop or Non-Drop Frame 102
Putting the Time Code Display on Hold 102
Setting the User Bit 104
Synchronizing with an External Device 105
Connecting an External Device 105
Reference Video Signal Input (Genlock
Synchronization) 106
Time Code Signal Input 106
Reference Video Signal Output 107
Time Code Signal Output 107
Recording Audio 108
Audio Settings and Recorded Audio
Channels 108
Connecting an External Microphone or External
Audio Input Source to the Camera 109
Setting the Audio Input Type for the INPUT 1/
INPUT 2 Terminals 110
Selecting the Audio Input Source for Audio
Channels 111
Adjusting the Audio Recording Level 111
Additional Settings for External Analog
Microphones 112
Monitoring the Audio with Headphones 113
Colors Bars/Audio Reference Signal 114
Color Bars 114
Audio Reference Signal 114
Waveform Monitor 115
Displaying the Waveform Monitor 115
Configuring the Waveform Monitor 115
Adding an $ Mark or % Mark to a
Recording 117
Using Metadata 118
Setting a User Memo Created with Canon XF
Utility 118
Entering Information About the Recording 119
Recording GPS Information (Geotagging) 120
Using Anamorphic Lenses 122
Using the Optional RC-V100 Remote
Controller 123
Taking Photos 125
Taking Photos 125
Photo Numbering 125
8
4. Customization 127
Assignable Buttons and Customizable USER
Screen 127
Changing the Assigned Function and Using an
Assignable Button 127
Assignable Functions 128
Customizing and Using the USER Screen 130
Custom Picture Settings 131
Selecting Custom Picture Files 131
Editing a Custom Picture File’s Detailed
Settings 131
Resetting Custom Picture Files 132
Renaming Custom Picture Files 132
Protecting Custom Picture Files 132
Copying Custom Picture Files 133
Embedding Custom Picture Settings in a
Clip 133
Available Custom Picture Settings 134
Customizing Onscreen Displays 139
Saving and Loading Camera Settings 140
Saving Camera Settings 140
Loading Camera Settings 140
5. Playback 141
Playback 141
The PLAY (Playback Control) Screen 141
Selecting the Recording Media and Format to Play
Back 142
Playing Back Clips 142
Onscreen Displays During Playback 144
Clip/Photo Operations 145
Displaying Clip Information 145
Adding and Deleting $ Marks or % Marks 146
Deleting Clips and Photos 147
Deleting the User Memo and GPS
Information 147
Copying a Custom Picture File Embedded in a
Clip 148
6. External Connections 149
Video Output Configuration 149
Main Recording Video Configuration and Video
Output Configuration from
the SDI OUT Terminals 149
Main Recording Video Configuration and Video
Output Configuration from the
MON. Terminals and HDMI OUT
Terminal 150
Playback Video Configuration and Video Output
Configuration by Terminal 151
Connecting to an External Monitor or
Recorder 152
Connection Diagram 152
Using the SDI OUT Terminals 152
Using the MON. Terminals 153
Using the HDMI OUT Terminal 154
Superimposing Onscreen Displays on Video
Outputs 154
Applying a LUT to Video Outputs 155
Using a User LUT 157
Audio Output 160
Working with Clips on a Computer 161
Saving Clips to a Computer 161
Developing RAW Clips 161
7. Network Functions 163
About the Network Functions 163
Connecting to a Wi-Fi Network 164
Attaching the Optional Wireless File
Transmitter 164
Camera Access Point 165
Connecting in Infrastructure Mode 165
Wi-Fi Protected Setup (WPS) 166
Searching for Access Points 167
Connecting to a Wired (Ethernet) Network 168
Checking the Network’s Status and Settings 169
Checking and Changing Network Settings 169
Browser Remote: Controlling the Camera from a
Network Device 170
Setting Up Browser Remote 170
Starting Browser Remote 171
Using Browser Remote 173
9
IP Streaming 182
Preparations 182
Streaming Video over IP 183
FTP File Transfer 185
Preparations 185
Transferring Clips (FTP Transfer) 186
8. Camera Menus 187
Setup Screens and Menu Options 187
Setup screens 187
Camera Menu and Monitoring Menu 190
9. Using the CDX-36150 Recorder 203
Preparations 203
Attaching the CDX-36150 Recorder to the
Camera 203
Removing the CDX-36150 Recorder 204
Powering the CDX-36150 Recorder 204
Initializing a Capture Drive 205
Recording with the CDX-36150 Recorder 206
Video Configuration 206
Shooting frame rates during slow & fast
motion 207
Main Recording Video Configuration and Video
Output Configuration from
the SDI OUT Terminals 209
Main Recording Video Configuration and Video
Output Configuration from the MON.
Terminals and HDMI OUT Terminal 210
Sub Recording on a CFast or SD Card 211
Playing Back Recordings from the Capture
Drive 211
10. Additional Information 215
Displaying the INFO Screens 215
Troubleshooting 219
List of Messages 224
Handling Precautions and Safety Instructions 229
Maintenance/Others 232
Optional Accessories 233
Specifications 235
Appendix: Compatible Lenses and Functions 240
Appendix: Camera Dimensions 242
Approximate Recording Times 247
Index 249
10
1
11
Introduction
About this Manual
Thank you for purchasing the Canon EOS C700 / EOS C700 PL / EOS C700 GS PL / EOS C700 FF /
EOS C700 FF PL. Please read this manual carefully before you use the camera and retain it for future reference.
Should the camera fail to operate correctly, refer to
Troubleshooting
(A 219).
Conventions Used in this Manual
IMPORTANT: Precautions related to the camera’s operation.
NOTES: Additional topics that complement the basic operating procedures.
A: Reference page number.
[]qr: Text that applies only to the model shown in the icon.
The following terms are used in this manual.
“Monitoring screen” refers to the screen of a monitoring device (either the optional EVF-V70 OLED Electronic
Viewfinder or an external monitor connected to one of the camera’s MON. terminals or HDMI OUT terminal).
“SD card” refers to an SD, SDHC or SDXC memory card.
“Recording media” refers to CFast cards, SD cards and Codex Capture Drive 2.0 media.
“The optional viewfinder” refers to the optional EVF-V70 OLED Electronic Viewfinder.
“CDX-36150 Recorder” refers to the commercially available CDX-36150 Codex Recorder for Canon EOS
C700.
Photographs in the manual are simulated pictures taken with a still camera. Screenshots in the manual are
from the C700 or C700 FF. Furthermore, some screenshots have been altered to make them easier to read.
Illustrations in the manual show the Canon EOS C700 camera with a Canon EF50mm f/1.4 USM lens
attached.
The following style is used to represent menu selections. The first word (in the thick, bold typeface) indicates
the button you need to press on the camera (in the case of “EVF”, on an optional EVF-V70 OLED Electronic
Viewfinder connected to the camera) to open the required menu. For a detailed explanation on how to use the
menus, refer to
Using the Menus
(A 32). For a summary of all available menu options and settings, refer to
the appendix
Setup Screens and Menu Options
(A 187).
Selecting the Main Recording Format
1 Open the [Main Rec Format] submenu.
[Rec/Media Setup] (3) > [Main Rec Format]
Alternatively, from the camera menu: [S&F FPS] > [OPTIONS] > [Main Rec Format].
2 Select [XF-AVC (CFast)] or [ProRes (CFast)] and then press SET.
This indicates to press the
MENU button on the camera
or EVF button on the optional
viewfinder.
Brackets [ ] indicate text as it appears on the
camera’s control display or on the screen of a
monitoring device.
This arrow indicates a deeper
level in the menu hierarchy or
the next step in a procedure.
Supplied Accessories
12
Supplied Accessories
The following accessories are supplied with the camera.
1
Comes pre-attached to the camera.
2
Used to secure the optional WFT-E6 or WFT-E8 Wireless File Transmitter or optional GP-E1 GPS Receiver when it is attached to
the camera.
3
Used to secure the CDX-36150 Codex Recorder for Canon EOS C700 when it is docked with the camera.
Battery Adapter for
V-Mount Batteries
1
Handle Unit Microphone Holder Clamp Base
Control Display Cover
1
Body Cap
1
Tape Measure Hooks
1
(x 2) Extension Unit Attachment Bracket
2
Reinforcement Plate for the
CDX-36150 Recorder
3
including 0.64 cm,
1/4" fixation screws (x 2)
Hex Wrenches (x 2)
(for 0.64 cm, 1/4" screws/
for M4 bolts)
CR2025 Lithium Button Battery Rubber Anti-Slip Feet (x 4)
13
Names of Parts
Names of Parts
811
*
12
*
18
*
21
*
22
*
12
*
23
*
24 25
*
19
13 14
*
15
*
16
*
17
*
769
*
10
*
1
*
2
*
3
*
4
*
5
*
20
* Illuminated buttons (A 199).
1 MAGN. (magnification) button (A 92)/
Assignable button Camera 1 (A 127)
2 PEAKING button (A 91)/
Assignable button Camera 2 (A 127)
3 ND FILTER +/– buttons (A 78)
4 FALSE COLOR button (A 100)/
Assignable button Camera 3 (A 127)
5 WFM (waveform monitor) button (A 115)/
Assignable button Camera 4 (A 127)
6 Tape measure hook and focal plane mark
7 Control dial (A 77, 80)
8 CUSTOM (customize the control dial’s function)
switch (A 77)
9 PUSH AUTO IRIS (momentary automatic aperture)
button (A 81)
10 USER (user-defined setup screen) button
(A 130)
11 ALT (alternative setup screen) button (A 188)
12 Screen buttons (A 30)
13 Control display (A 30)
14 HOME (home setup screen) button (A 30, 187)
15
Q
button (A 28)
16 C (key lock) button (A 56)
17 MENU (camera menu) button (A 32)
18 REC (start/stop recording) button (A 55)
19 Tally lamp (A 55)
20 Speaker (A 56)
21 PLAY (playback mode) button (A 141)
22 TC (time code) button (A 101, 189)
23 BACK (go back to previous screen) button
(A 30, 32)
24 SELECT dial/SET button (A 30, 32)
25 INFO (information screens) button (A 215)
Names of Parts
14
p15
13 4
13 14 15 16 17 18 19 20 21
5
67 910
11 12
82
1D-TAP terminal (A 28)
2 Cable clamp
3 Exhaust ventilation outlet (A 64)
4 Tally lamp (A 55)
5 System extension terminal (A 120, 164)
6 REC (start/stop recording) button (A 55)
7 SLOT SEL. (CFast card selection) button
(A 52, 142)
8Serial number
9 Air intake vent (A 64)
10 Tape measure hook and focal plane mark
11 Audio input selection switches: for INPUT 1 (top),
for INPUT 2 (bottom) (A 108, 110)
12 ANALOG (analog audio source selection)
switches: for INPUT 1 (top), for INPUT 2 (bottom)
(A 108, 110)
13 SD card slot cover switch (A 50)
14 SD CARD access indicator (A 50)
15 CFast (CFast card slot A) and CFast (CFast
card slot B) access indicators (A 49)
16 CFast card slot cover switches: for CFast (top),
for CFast (bottom) (A 49)
17 SD card slot cover (A 50)
18 SD card slot (A 50)
19 CFast card slot covers: for CFast (top), for
CFast (bottom)
20 CFast card slots: for CFast (top), for CFast
(bottom) (A 49)
21 CFast card release switches: for CFast (top),
for CFast (bottom) (A 49)
15
Names of Parts
Removing and Attaching the Terminal Covers
You can remove the covers of the camera’s terminals to access them more easily. The terminal cover of the
terminals below the MIC terminal (on the camera’s front side) is common to all 6 terminals. Terminal covers for
other terminals can be removed by removing the small screw using a Phillips head (“crosshead”) screwdriver.
Be careful not to lose the terminal covers or fixation screws once removed.
1
78 9 10
11 12 13
2
3
4
5
6
17
15 10
1311 16
14
Zq
EF lens mount with Cinema Lock (A 44)
[]r
PL lens mount (A 46)
1 MIC (microphone) terminal (A 109)
2VIDEO terminal (A 41)
For connecting the optional EVF-V70 OLED
Electronic Viewfinder.
3 DC OUT 24V 2A (power output) terminal (A 28)
4 DC OUT 12V 2A (power output) terminal (A 28)
5 CTRL (controller) terminal (A 38)
For connecting the optional OU-700 Remote
Operation Unit.
6LENS terminal (A 44)
7 EF-S lens mount index (A 44)
8 EF lens mount index (A 44)
9 Lens mount handles
10 Built-in monaural microphone (A 110)
11 REC (start/stop recording) button (A 55)
12 EF lens contacts (A 44)
13 ONE-SHOT AF (focus automatically once) button
(A 92)/Assignable button Camera 5 (A 127)
14 Bayonet ring handles
15 PL lens index pin (A 46)
16 PL lens contacts (A 46)
17 Bayonet ring
Names of Parts
16
MON. 1
MON. 2
GENLOCK/
SYNC OUT
TIME CODE
IN/OUT
HDMI
OUT
1
2
3
4
9810111213
16
15
14
17
18
19 20
7
6
5
(with the supplied battery adapter attached to the camera)
(with no extension module attached to the camera)
1 V-mount battery plate (A 26)
2 V-shaped battery mount (V-mount)
3 Battery release latch (A 26)
4 Battery contacts
5 Extension module mounting unit (A 23, 24)
6 Extension module connector
7 Compartment cover for the lithium button battery
(A 24)
8 Cable clamp
9 TIME CODE IN/OUT terminal (A 105, 106, 107)
10 GENLOCK terminal (A 105, 106)/
SYNC OUT (synchronizing signal output) terminal
(A 105, 107)
11 MON. terminals: MON. 1 (top), MON. 2 (bottom)
(A 149, 153)
12 SDI OUT terminals: from top to bottom SDI OUT 1
to SDI OUT 4 (A 149, 152)
13 REMOTE B terminal
14 REMOTE A terminal
For connecting the optional RC-V100 Remote
Controller (A 123) or commercially available
remote controllers.
15 (Ethernet) terminal (A 168)
16 (Ethernet) indicator
17
×
(headphone) terminal (A 113, 143)
18 INPUT terminals (XLR): INPUT 1 (top), INPUT 2
(bottom) (A 109, 110)
19 HDMI OUT terminal (A 149, 154)
20 DC IN 12V terminal (A 27)
17
Names of Parts
1234 5 678
23 79
1 Tape measure hooks and focal plane marks
Use the hooks to accurately measure the distance
from the focal plane.
2 Screw holes for 1/4"-20 mounting screws (10 mm
(0.39 in.) deep)
Total of 36 on the top plate and 16 on the bottom
plate.
3 Screw holes for 3/8"-16 mounting screws
(12 mm (0.47 in.) deep)
Total of 10 on the top plate and 5 on the bottom
plate.
4 Screw holes for 1/4"-20 mounting screws (10 mm
(0.39 in.) deep)
Recommended mounting position for the optional
OU-700 Remote Operation Unit.
5 Socket for the extension unit attachment bracket
(A 120, 164)
6 Battery adapter release switch (A 23, 24)
7 Battery adapter’s fixation screws (2 on the top
plate, 2 on the bottom plate; M4) (A 23, 24)
8 Battery adapter for V-mount batteries
(A 23, 24, 26)
9 Rubber anti-slip feet
The screw holes on the bottom can be used to
attach the supplied rubber anti-slip feet as shown
in the illustration.
Names of Parts
18
Microphone Holder (A 109)
Handle Unit
(A 40)
1 Microphone lock screw
2 Microphone holder
3 Microphone cable clamp
4 Hex socket head fixation bolts (0.64 cm,
1/4"; 2 in total)
5 Through-holes for fixation bolts
11
*
2
32
*
1
2
* One more in the same location on the opposite side.
1 Screw holes for 1/4"-20 mounting screws
(10 mm (0.39 in.) deep, 9 in total)
2 Screw holes for 3/8"-16 mounting screws
(12 mm (0.47 in.) deep, 8 in total)
3 Hex socket head fixation bolts
(0.64 cm, 1/4"; 4 in total)
19
Names of Parts
Clamp Base (A 41)
12 3
1 Slider for an optional viewfinder’s clamp rail
2 Clamp rail locking screw
3 Hex socket head fixation bolts (0.64 cm, 1/4";
4 in total)
Names of Parts
20
EVF-V70 OLED Electronic Viewfinder (optional) (A 41)
1
*
12 10 14 15 16
2
*
3
*
45 768
*
9
*
10 11
13
* Illuminated buttons (A 199).
1 FUNC (main functions) button (A 73)/
Assignable button EVF 1 (A 127)
2 EVF (open the monitoring menu) button (A 33,
190)/Assignable button EVF 2 (A 127)
3 BACK (go back to previous screen) button
(A 30, 32)
4 Viewfinder (A 41)
5Eye sensor (A 42)
6Eyecup
7 Dioptric adjustment ring (A 42)
8 MAGN. (magnification) button (A 92)/
Assignable button EVF 3 (A 127)
9 FALSE COLOR button (A 100)/
Assignable button EVF 4 (A 127)
10 Swing arm locking screw (A 41)
11 Swing arm
12 VIDEO terminal (A 42)
13 Screw hole for 1/4"-20 mounting screws
(25 mm (0.98 in.) deep)
14 SELECT dial/SET button (A 32)
15 Joystick (A 32)/SET button (A 32)
16 Swing arm slider (A 41)
17 18
19 20
17 Clamp rail: cable clamps
18 Screw holes for the clamp rail’s cable clamps
19 Clamp rail: rail end caps (A 41)
20 Clamp rail: slider locking pin (A 43)
21
4K Workflow Overview
4K Workflow Overview
The following illustrates the typical 4K workflow for this camera.
Shoot in 4K mode (A 65).
You can record RAW data on a CDX-36150 Recorder docked with the camera. You can also record
Intra-frame (YCbCr 4:2:2) 4K data on a CDX-36150 Recorder or on a CFast card in the camera.
In addition to the main RAW recording, you can record simultaneously an additional sub recording
in the camera (A 71). You can use the CFast card (XF-AVC clips, 4K or 2K) or SD card (XF-AVC
Proxy clips, 2K), depending on the type of sub recording clips you need or how you intend to use
them in post-production.
After recording RAW data, you can develop the RAW data using the Cinema RAW Development
software (A 161) to generate full-quality data. Using the Canon RAW Plugin, you can work with
RAW recordings directly from supported NLE applications.
You can also generate proxy data with the software.
YCbCr 4:2:2 clips recorded on the CFast card can be treated as full-quality data without any additional
processing.
Transfer the 2K clips recorded in the camera or CDX-36150 Recorder, or proxy data generated by
the software, to your NLE system and edit offline (A 161).
Perform color grading based on the full-quality data.
Recording Post-production
YCbCr
4:2:2 data
SD card
EDL
NLE software
Cinema
RAW
Development
Color
grading
2K recording
(XF-AVC Proxy)
RAW data
Proxy data
Full-quality
data
Proxy
data
CFast card
4K or 2K recording
(XF-AVC/ProRes)
CDX-36150
Recorder
4K recording
(RAW)
Extension module
connector (docking)
Internal recording
Internal recording
NLE Software
RAW
Plugin
Extension module
connector (docking)
4K or 2K recording
(ProRes)
CDX-36150
Recorder
4K Workflow Overview
22
Color Grading with the ACES Workflow
ACESproxy: ACESproxy video data that is output from the MON. terminals or HDMI OUT terminal when
performing on-set color grading. Select the [ACESproxy] option for the LUT setting of the
appropriate terminal (A 155) to enable ACESproxy output.
Input Transform: Refers to the table used for converting color information of the input device to ACES2065-1
color space.
Output Transform: Refers to the table used for mapping ACES2065-1 color space information to the specific
color information scheme used by the display device.
ASC-CDL: Refers to the list that contains color grading adjustment data. This step requires equipment
compatible with ASC-CDL.
Extension
module
connector
(docking)
CDX-36150
Recorder
Cinema RAW
Development
Color grading
Post-production
On-set Color Grading
ACES
proxy
Inverse log
ASC-CDL
MON. or HDMI OUT
output
RAW
data
OpenEXR
(ACES 1.0)
Input
Transform
ASC-
CDL
4K recording
(RAW)
Output
Transform
Output
Transform
2
23
Preparations
Preparing the Backup Battery
The camera uses a CR2025 lithium button battery as a backup battery to ensure that the camera’s settings are
not lost when no other power source is connected to the camera. To install the supplied lithium button battery,
you will need to remove any extension modules attached to the camera*.
* The camera is shipped with the battery adapter for V-mount batteries attached.
Removing an Extension Module
The following procedure is explained using the battery adapter for V-mount batteries supplied with the camera
as example.
1 Use the supplied hex wrench to remove the four fixation screws from the top and bottom of the
battery adapter.
2 Slide the battery adapter release switch in the direction of the arrow.
The locking lever will pop out.
3 Pull the locking lever all the way up and pull the top of the battery adapter away from the camera.
4 Lift up the battery adapter and remove it from the camera.
5 Push down the locking lever until it clicks.
Preparing the Backup Battery
24
Inserting the Lithium Button Battery
The camera features a built-in backup battery so the camera settings are not lost while you replace the lithium
button battery.
1 Make sure no power supply is connected to the DC IN 12V
terminal.
2 Turn the lithium battery compartment cover to the OPEN
position and remove the cover.
Use a coin or a similar tool. If you keep turning the cover beyond
the OPEN point, the cover will rise a little, making it easier to grab.
3 Insert the supplied lithium button battery with the + side
facing out.
4 Replace the cover and turn it to the LOCK position to lock it.
NOTES
The built-in backup battery will be completely depleted if you do not
use the camera for about 1 month. Replacing the lithium button
battery in such case will reset all the camera’s settings to default
values. To avoid losing the settings, you can save them on an SD
card in advance (A 140).
To recharge the built-in backup battery, turn off the camera and connect a sufficiently charged power source
(battery or DC IN 12V terminal). The built-in backup battery will be fully charged in about 24 hours.
Installing an Extension Module
The following procedure is explained using the battery adapter for V-mount batteries supplied with the camera
as example.
1 Slide the battery adapter release switch in the direction of the arrow.
The locking lever will pop out. Once it does, pull the locking lever all the way up.
2 Attach the battery adapter to the camera and slide it down.
Align the positioning protrusions on the battery adapter with the holes on the camera’s body.
3 Gently press the battery adapter toward the camera.
25
Preparing the Backup Battery
4 Push down the locking lever until it clicks.
5 Using the supplied hex wrench, attach the four fixation screws to the top and bottom of the battery
adapter to secure it in place.
NOTES
When tightening the screws, tighten them lightly at first and then turn the supplied hex wrench about 45
degrees further. Applying a torque of 250 N·cm (2.5 N·m) or more may damage the screw threads.
Preparing the Main Power Supply
26
Preparing the Main Power Supply
You can power the camera using a commercially available V-mount battery or the DC IN 12V terminal. Even
when a battery is attached, if a power source is connected to the DC IN 12V terminal, the camera will not draw
power from the battery.
Acceptable Power Sources
When selecting commercially available batteries and power adapters, make sure the external power source
meets the following specifications and all the safety standards of the country/region where it is used. Closely
follow the manufacturer’s instructions regarding the use and maintenance of power sources.
Using a Battery
The battery adapter for V-mount batteries comes attached to the camera. If it was removed, attach the battery
adapter in advance (A 24).
Attaching a Battery
1 Make sure the camera is turned off.
2 Align the V-shaped wedge on the battery to the V-mount on the
battery plate.
3 Gently press the battery down until it clicks in place.
Removing a Battery
1 Press the
Q
button to turn off the camera.
2 While holding the battery release latch pressed down, slide the
battery up and remove it.
Power source Specifications
Battery V-mount battery, 12 V to 20 V DC
Power adapter
(DC IN 12V terminal)
4-pin XLR plug (female connector), 11.5 V to 20 V DC, 10 A (acceptable maximum load current)
27
Preparing the Main Power Supply
Using the DC IN 12V Terminal
1Press the
Q
button to turn off the camera.
2 Connect the 4-pin XLR connector of the external power
supply to the camera’s DC IN 12V terminal.
IMPORTANT
Make sure to turn off the camera before connecting or
disconnecting an external power source to/from the
camera’s DC IN 12V terminal.
Checking the Camera’s Power Levels
You can check the voltage level of the power source used on the camera’s HOME screen, the shooting screen
that appears on monitoring devices (A 57, 59) and the [SYSTEM] screen* (
qr
).
You can use the [System Setup] > [Low Power Warning] settings to set a critical power level
independently for the DC IN 12V terminal and battery. When the power input to the camera reaches the
predetermined level, the onscreen power indicator will change to red and a message will appear in the
[LIVE] screen. When using a battery compatible with BMS (battery management system), you can even set the
warning level as a percentage of the remaining battery charge instead of voltage.
* This screen shows only the voltage of the CDX-36150 Recorder’s power supply (DC IN or battery).
NOTES
If the power supplied to the camera is at or below the level set for the power level warning (A 199), the
camera will not start recording.
Preparing the Main Power Supply
28
Power Outputs
The camera features three power outputs for accessories: the DC OUT 24V 2A terminal, the DC OUT 12V 2A
terminal and the D-TAP terminal on the battery adapter.
* Actual levels may vary depending on the power source supplying the camera.
IMPORTANT
Be sure to use the camera’s power outputs within the specifications given.
When supplying power to external accessories, be careful of the polarity of the power connections.
Connecting the power supply incorrectly can cause malfunctions.
Turning the Camera On and Off
After connecting an appropriate power source to the camera, press
the
Q
button to turn on the camera. While the camera is
starting up, the tally lamp will illuminate in red. When the camera is
ready to start recording, the tally lamp will change to green and the
HOME screen will be displayed on the camera’s control display.
To turn off the camera, press and hold the
Q
button. After
the countdown that appears on the control display ends, the
camera will start the shutting down process and will turn off after a
few seconds.
Power output Specifications*
DC OUT 24V 2A terminal Fischer 3-pin connector, 24 V DC, 2.0 A (max.)
DC OUT 12V 2A terminal LEMO 2-pin connector, 12 V DC, 2.0 A (max.)
D-TAP terminal D-Tap connector, 50 W (max.)
Tall y l a m p
29
Date, Time and Language Settings
Date, Time and Language Settings
Setting the Date and Time
You will need to set the date and time on the camera before you can start using it. When you turn on the camera
for the first time or after the camera’s settings were reset, the [Date/Time] screen will appear automatically on the
control display with the time zone selected so you can set the camera’s internal clock.
1 Turn the SELECT dial to select the desired time
zone and then press SET to move to the next
field.
The default time zone is [UTC-05:00] (New York)
or [UTC+01:00] (Central Europe), depending on
the country/region of purchase. Time zones are
based on Coordinated Universal Time (UTC).
2 Change the rest of the fields in the same way.
You can also press the [<] and [>] screen buttons
to move between the various fields.
3 After correctly setting the date and time, press
the [OK] screen button to start the clock and
close the screen.
NOTES
With the [System Setup] > [Set Clock] settings, you can change the time zone, date and time also
after the initial setup. You can also change the date format.
If the lithium button battery and built-in backup battery are both completely depleted, all menu settings will be
lost. In such case, replace the lithium button battery (
A 23) and perform the initial setup again.
Using the optional GP-E1 GPS Receiver, you can have the camera adjust settings automatically according to
the UTC date/time information received from the GPS signal (A 120).
Changing the Language
The camera’s default language is English. You can change it to German, Spanish, French, Italian, Polish,
Portuguese, Russian, Simplified Chinese, Korean or Japanese. Please note that some settings and screens will
be displayed in English, regardless of the language setting.
1 Press the MENU button.
2 Turn the SELECT dial to select [System Setup] and then press SET.
3 Select [Language
H
] in a similar fashion and then press SET.
4 Turn the SELECT dial to select a language.
5 Press SET to change the language and then press the HOME button to close the menu.
Changing Camera Settings with the Screen Buttons
30
Changing Camera Settings with the Screen Buttons
There are three basic ways to change the various camera settings: Using the screens that appear on the
camera’s control display and the screen buttons, using the camera menu displayed on the control display, and
using the monitoring menu displayed on monitoring devices along with the camera’s image. The menus will be
explained in the following section (A 32). This section will explain the use of the control display screens and
screen buttons. When an optional OU-700 Remote Operation Unit is connected to the camera, using the
OU-700 is identical to using the camera’s control display and buttons.
Unlike the menus, the function of the screen buttons changes dynamically depending on the button pressed on
the camera and the screen currently displayed on the control display. The current function of the screen buttons
is displayed in the gray area immediately above/below the screen button. If applicable, the current setting is
displayed within the white enclosure connected to it.
The HOME, USER, ALT, TC and PLAY buttons, each opens a different setup screen where you can change
settings or perform actions (A 187).
Options
HOME screen: This screen is displayed by default when you turn on the camera. In this screen you can change
the frame rate, aperture and ND filter settings, shutter speed, ISO speed/gain, custom picture
settings and white balance. You can also check the status of the camera, clip name, recording
format, information about recording media and power supply.
USER screen: You can customize this screen to your needs by assigning the functions you prefer to the 6
screen buttons.
ALT screen: In this screen you can change settings related to autofocus (
Zq
) and the focus
assistance functions, audio, the camera’s electronic level and network functions.
TC screen: In this screen you can change time code related settings.
PLAY screen: In this screen you can control the playback of your recordings (playback mode).
SELECT dial: Turn to move
between options.
SET button: Confirm the
selected option.
BACK button: Return to the
previous screen without
changing the setting.
Screen button. In this example, pressing the button will open
a screen where you can change the shutter speed.
Current function of the screen button. In the
manual pressing this screen button will be
referred to as “Press [SHUTTER]”.
Current value of the shutter speed.
31
Changing Camera Settings with the Screen Buttons
Following is a step-by-step example of how to change a setting using the screen buttons. In the manual, these
will be abbreviated in most cases. For example, the instruction below stands for the procedure following it.
[SHUTTER] > Desired shutter value > Press SET
1 Press the HOME button.
The HOME screen will appear.
2 Press the [SHUTTER] screen button.
The shutter speed selection screen will appear with the current shutter
speed value marked with an orange selection frame.
3 Turn the SELECT dial to select the desired value and then press
SET.
The selected value will be applied and the previous screen will be
displayed. If necessary, press the HOME button to return to the
HOME screen.
You can press the BACK button instead of the SET button to return
to the previous screen without changing the current value.
Adjusting the Control Display
You can adjust the brightness of the control display on the camera or on an optional OU-700 Remote Operation
Unit connected to the camera. This adjustment will not affect your recordings.
1 Open the control display's [Brightness] submenu.
[Monitoring Setup] (
¢
) > [Control Display] > [Camera] or [Remote OU-700] > [Brightness]
2 Select the desired level ([5] is the brightest) and then press SET.
Alternatively, you can adjust the control display’s brightness from the HOME screen by turning the SELECT
dial while holding the BACK button pressed down.
NOTES
If necessary, you can remove the control display’s protective cover inserting a fingernail or other thin object
under the bottom center of the cover and pulling it. After cleaning the control display place back the protective
cover on the control display and push all four corners to secure it in place.
With the [Monitoring Setup] > [Control Display] > [Camera] > [Turn Off Display] setting, you can
set the camera so the camera’s control display is turned off automatically whenever an optional OU-700
Remote Operation Unit is connected to the camera.
If you set an assignable button to [Control Display Setup] (A 127), you can press the button to open the
monitoring menu’s [Control Display] submenu. If you set an assignable button to [Control Display] (A 127),
you can press the button to turn the control display on/off.
You can use the [System Setup] > [LED] > [Button Illumination] setting to turn on the buttons’
illumination and change their brightness. Alternatively, you can do so from the HOME screen by turning the
SELECT dial while holding the HOME button pressed down.
About the control display and optional viewfinder: The screens are produced using extremely high-precision
manufacturing techniques, with more than 99.99% of the pixels operating to specification. Very rarely, pixels
may misfire or may light up permanently as white dots. This has no effect on the recorded image and does not
constitute a malfunction.
Using the Menus
32
Using the Menus
You can change the camera’s settings using the camera menu displayed on the control display or the
monitoring menu displayed on the screen of connected monitoring devices. You can also register frequently
used menu settings in 6 customized submenus (My Menu 1 to 3 that can be set up independently for the
camera menu and the monitoring menu) (A 35). For detailed tables of all the available menu options and
settings, refer to
Setup Screens and Menu Options
(A 187).
Selecting an Option from the Camera Menu
The camera menu appears on the control display and is limited, for the most part, to functions that cannot be set
using the screen buttons. You can press the MENU button to open the camera menu regardless of the setup
screen currently displayed.
Following is a step-by-step explanation of how to change a setting using the camera menu. In the manual, such
instructions will be abbreviated and will omit the closing of the menu in most cases. For example, the instruction
below stands for the procedure following it.
[System Setup] > [Firmware]
1 Press the MENU button.
2 Turn the SELECT dial to select the desired submenu (in the example [System Setup]) and then press
SET.
The orange selection frame will appear on a menu item in the submenu.
If a submenu contains many menu items, a scroll bar will appear on the right side of the submenu indicating
that you must scroll up or down to see other menu items.
Press the BACK button to return to the previous submenu.
3 Turn the SELECT dial to select the desired menu item (in the example [Firmware]) and then press
SET.
A [>] mark to the right of a menu item indicates another submenu. Repeat this step until you get to the
desired menu item.
A list of setting options will appear with the orange selection frame around the current setting.
Press the BACK button to return to the previous submenu without changing the setting.
SELECT dial:
Turn to move the orange selection frame
between menu settings/options.
SET button:
Confirm the selected menu setting/option.
MENU button:
Open the camera menu.
BACK button:
Return to the previous menu level without changing
the setting.
From the main menu, it closes the camera menu.
33
Using the Menus
4 Turn the SELECT dial to select the desired setting option and then press SET.
Depending on the menu item, additional selections may be necessary.
5 Press the HOME button to close the menu and return to the HOME screen.
Selecting an Option from the Monitoring Menu
The monitoring menu appears on the screen of external monitors connected to one of the camera’s MON.
terminals or to the HDMI OUT terminal and on the optional EVF-V70 OLED Electronic Viewfinder connected to
the camera’s VIDEO terminal. The monitoring menu contains almost all of the camera’s settings and can be
operated using the optional viewfinder or an optional RC-V100 Remote Controller connected to the camera
(A 123). For simplicity’s sake, the instructions throughout this manual will assume the use of the optional
viewfinder.
EVF button: Open the monitoring menu. On the RC-V100, press the MENU button instead.
BACK button: Return to the previous menu level without changing the setting. Pressing the button when one of
the icon tabs is highlighted in orange will close the monitoring menu. On the RC-V100, press the
CANCEL button instead.
SELECT dial: Turn to move the orange selection frame between menu settings/options.
Joystick: Push the joystick to move the orange selection frame between menu settings/options. On the
RC-V100, press the Up/Down/Left/Right buttons instead. Press the joystick itself to confirm the
selected menu setting/option.
SET button: Confirm the selected menu setting/option. (In the manual, “Press SET” includes also pressing
the joystick.)
Following is a step-by-step explanation of how to change a setting with the monitoring menu. In the manual,
such instructions will be abbreviated and will omit the closing of the menu. For example, the instruction below
stands for the procedure following it.
[System Setup] (
B
) > [Language
H
] > Desired language
1 On the optional viewfinder, press the EVF button. On an optional RC-V100 Remote Controller, press
the MENU button.
The monitoring menu appears on the screen.
If you used the EVF button, the [EVF-V70] submenu will appear on the optional viewfinder’s screen with the
[Brightness] setting selected. To change other settings, press the BACK button twice to return to the
monitoring menu’s top level (with one of the icon tabs highlighted in orange).
2 Push the joystick up/down or turn the SELECT dial to select the desired submenu (in the
example highlight the
B
tab corresponding to [System Setup]).
3 Push the joystick right or press SET.
Using the Menus
34
The orange selection frame will appear on a menu item in the submenu.
Press the BACK button to return to the previous submenu.
4 Push the joystick up/down or turn the SELECT dial to select the desired menu item (in the example
[Language
H
]).
If a submenu contains many menu items, a scroll bar will appear on the right side of the submenu indicating
that you must scroll up or down to see other menu items.
•A
Ð
mark to the right of a menu item indicates another submenu. Repeat steps 3 and 4.
5 Push the joystick right or press SET.
The orange selection frame will appear on a setting option.
Press the BACK button to return to the previous submenu.
6 Push the joystick up/down or turn the SELECT dial to select the desired setting option and then
press SET.
Depending on the menu item, additional selections may be necessary.
7 Press the EVF button twice* (optional viewfinder only) or the MENU button once (RC-V100 only) to
close the menu.
* Only once when the [EVF-V70] submenu is being displayed.
NOTES
Unavailable items may appear grayed out.
On some screens, the or icon may appear with some guidance text. Press SET or press the BACK
button, respectively, to perform the action displayed.
You can check some of the current settings on the camera’s information screens (A 215).
When the HDMI OUT terminal’s resolution is set to 4096x2160 or 3840x2160, the monitoring menu will not be
displayed on the monitor connected to the HDMI OUT terminal.
35
Using the Menus
Using the Customized Submenu (My Menu)
You can register up to 15 frequently used menu settings under a My Menu submenu for easy access. You can
save up to 6 separate sets of My Menu settings (3 each for the camera menu and monitoring menu) so you can
customize different options for different shooting situations. Furthermore, if you set an assignable button to [My
Menu] (A 127), you can press the button to access your registered monitoring menu settings even faster and
more easily.
Selecting a My Menu Set
1 Open the My Menu [Select] screen.
[My Menu]* > [Select]
* The icon and submenu name will reflect the My Menu set currently selected. By default this is [My Menu 1] ( ).
2 Select the desired My Menu set and then press SET.
Adding Menu Settings
1 Open the My Menu [Register] screen.
[My Menu]* > [Edit] > [Register]
* The icon and submenu name will reflect the My Menu set currently selected. By default this is [My Menu 1] ( ).
The menu’s title bar will change to blue to indicate you are selecting menu settings to add to the My Menu
submenu.
Press the BACK button to cancel the operation and return to the regular menu.
2 Navigate the menus to find the menu setting you want to add and then press SET.
3 Camera menu: Press [OK].
Monitoring menu: Select [OK] and then press SET.
The menu setting you registered will now appear under the currently selected My Menu set.
4 When the confirmation screen appears, press [OK] (camera menu) or press SET (monitoring menu).
Rearranging Menu Settings
1 Open the My Menu [Move] screen.
[My Menu]* > [Edit] > [Move]
* The icon and submenu name will reflect the My Menu set currently selected. By default this is [My Menu 1] ( ).
2 Turn the SELECT dial to select the setting you want to move and then press SET.
An orange
]
icon will appear next to the setting you selected to move.
3 Move the setting to the desired position and then press SET.
4 Camera menu only: Press [OK].
Removing Menu Settings
1 Open the My Menu [Delete] screen.
[My Menu]* > [Edit] > [Delete]
* The icon and submenu name will reflect the My Menu set currently selected. By default this is [My Menu 1] ( ).
2 Select the setting you want to remove and then press SET.
3 Camera menu: Press both [DELETE] buttons simultaneously.
Monitoring menu: Select [OK] and then press SET.
4 When the confirmation screen appears, press [OK] (camera menu) or press SET (monitoring menu).
Using the Menus
36
Resetting the My Menu Submenu
1 Reset all the menu settings registered to the currently selected My Menu set.
[My Menu]* > [Edit] > [Reset All]
* The icon and submenu name will reflect the My Menu set currently selected. By default this is [My Menu 1] ( ).
2 Camera menu: Press both [RESET] buttons simultaneously.
Monitoring menu: Select [OK] and then press SET.
3 When the confirmation screen appears, press [OK] (camera menu) or press SET (monitoring menu).
Renaming the Selected My Menu Set
You can give each of the My Menu sets a more descriptive name to make them easier to identify.
1 Open the My Menu [Rename] screen.
[My Menu]* > [Edit] > [Rename]
* The icon and submenu name will reflect the My Menu set currently selected. By default this is [My Menu 1] ( ).
2 Monitoring menu only: Select [Input] and then press SET.
3 Enter the desired name (up to 8 characters) using the keyboard screen (A 37).
37
Using the Menus
Using the keyboard screen
1 Turn the SELECT dial (camera menu) or push the joystick in any direction (monitoring menu) to select a
character and press SET to add it to the text.
Camera menu only: Press [Aa1] to change the keyboard between capital letters, small letters and
numbers/special characters.
2 Repeat to keep adding characters to the text as necessary.
You can press [<]/[>] (camera menu) or select one of the  arrows and press SET (monitoring menu)
to move the cursor.
•Press [
] (camera menu) or select [
] and press SET (monitoring menu) to delete the character to the
left of the cursor (backspace).
Camera menu only: Press [CLEAR] to delete all the text and start over.
3 Press [OK] (camera menu) or select [OK] and press SET (monitoring menu) to confirm the text/value
entered.
Press the BACK button to return to the previous screen without changing the current text.
Short text/numbers version
For short text fields and numeric values, a shorter version of the keyboard may appear.
*
1 Turn the SELECT dial (camera menu) or push the joystick up/down (monitoring menu) to select the first
character or digit and press SET to move to the next.
2 Change the rest of the characters/digits in the same way.
You can also press [<]/[>] (camera menu) or push the joystick left/right (monitoring menu) to move
between characters/digits.
Camera menu only: Press [RESET] to reset the text or value to its initial setting.
3 Press [OK] (camera menu) or select [Set] and press SET (monitoring menu) to confirm the text/value
entered.
Press the BACK button to return to the previous screen without changing the current text/value.
Current text length/Character limit
Camera menu keyboard
Monitoring menu keyboard
Preparing the Camera
38
Preparing the Camera
This section presents various shooting configurations of the camera and explains how to attach a lens and
different accessories to the camera such as the supplied handle unit, the optional EVF-V70 OLED Electronic
Viewfinder, etc.
Shooting Configurations
You can use the camera with a number of modular units, supplied accessories and optional accessories to set
up the configuration that best matches your shooting needs. Following are some examples of shooting
configurations.
Configuration for Team Operation
You can attach the optional OU-700 Remote Operation Unit to the right side of the camera to allow one person
to use the camera menu while another uses the optional EVF-V70 OLED Electronic Viewfinder.
*
Supplied accessory.
**
Requires the removal of the supplied battery adapter for V-mount batteries.
Clamp rail
EVF-V70 OLED Electronic
Viewfinder
Microphone holder*
Clamp base*
Handle unit*
WFT-E6 or WFT-E8
Wireless File Transmitter/
GP-E1 GPS Receiver
UN-5 or UN-10
Unit Cables
MO-4E or MO-4P
B4 Mount Adapter
UC-V75 or UC-V1000
Remote Operation Unit Cable
OU-700 Remote Operation Unit
RC-V100 Remote Controller
V-Mount Batteries/
AC Adapters
(commercially available)
CDX-36150 Codex Recorder
for Canon EOS C700**
RR-10 or RR-100
8-pin Remote
Cable
39
Preparing the Camera
Configuration for One-Person Operation
* Supplied accessory.
IMPORTANT
Be careful not to drop the camera or modular units when attaching, removing or adjusting the various
accessories. Use a table or other stable surface to change the camera’s configuration.
NOTES
For a more convenient one-person operation, you can use the optional SG-1 Shoulder Style Grip Unit and
connect the 12-pin interface cable to the camera’s LENS terminal to be able to start/stop recording, operate
the zoom and aperture, access the monitoring menu, and more, directly from the grip unit.
For details about docking the CDX-36150 Recorder with the camera and using it to record, refer to
Using the
CDX-36150 Recorder
(A 203).
Clamp base*
Clamp rail
Microphone holder*
Handle unit*
EVF-V70 OLED Electronic
Viewfinder
V-Mount Batteries/
AC Adapters
(commercially available)
SG-1 Shoulder Style
Grip Unit
SU-15 Shoulder
Support Unit
UN-5 or UN-10
Unit Cables
Preparing the Camera
40
Attaching the Handle Unit
You can adjust the position of the handle considering the total weight
and center of gravity of the camera with the lens and all the accessories
used attached.
Attach the handle unit to the desired position on top of the
camera.
Use the supplied hex wrench to secure it firmly with the 4 hex socket
head bolts.
NOTES
The handle unit has screw holes for 1/4"-20 mounting screws
(10 mm (0.39 in.) deep) and for 3/8"-16 mounting screws (12 mm
(0.47 in.) deep), giving you the option to attach the supplied
microphone holder or other commercially available accessories.
Using a Tripod
Along its central axis, the camera’s bottom plate has 4 screw holes
for 1/4"-20 mounting screws (10 mm (0.39 in.) deep) and 5 screw
holes for 3/8"-16 mounting screws (12 mm (0.47 in.) deep) that can
be used to mount the camera on a tripod, dolly or other rigs.
Decide on the best position to use considering the total weight and
center of gravity of the camera with the lens and all the accessories
used attached.
IMPORTANT
Do not use tripods with mounting screws exceeding the depth of
the screw holes on the camera as this may damage the camera.
Checking that the Camera is Horizontal
You can use the camera’s electronic level to make sure the shooting plane is truly horizontal. On the control
display you can check the camera’s tilt (the degree of rotation of the optical axis up and down) and roll (the
degree of rotation sideways along the optical axis) as numerical values. On the monitoring screen you can
display an indicator that shows graphically the camera’s sideways roll (only).
1 Press the ALT button.
The camera’s inclination (tilt and roll) will be displayed on the control display.
2 If necessary, set the current camera position as the electronic horizon.
[CAM LVL] > Press both [SET] buttons simultaneously
NOTES
To display the visual level on the monitoring screen set [Monitoring Setup] > [Custom Display 2] >
[Level] to [On]. You can also use the [System Setup] > [Level Sensitivity] setting to adjust the
sensitivity of the camera’s electronic level.
You can reset only the electronic level to factory settings (without affecting other camera settings) with the
[System Setup] > [Reset] > [Level] setting.
Screw holes for
3/8"-16 screws
Screw holes for
1/4"-20 screws
41
Preparing the Camera
Using the Optional EVF-V70 OLED Electronic Viewfinder
After attaching the supplied clamp base to the camera, you can attach the optional EVF-V70 OLED Electronic
Viewfinder to the clamp base. An optional UN-5 or UN-10 Unit Cable is required to connect the optional
viewfinder to the camera. You can adjust the viewfinder’s swing arm and clamp rail sliders to set the viewfinder
to a comfortable viewing angle. To protect the viewfinder’s OLED panel, the viewfinder will be dimmed
automatically when it is not in use.
Throughout the manual, the EVF-V70 will be referred to simply as “the optional viewfinder”.
Attaching the Optional Viewfinder
1 Press the
Q
button to turn off the camera.
2 On the optional viewfinder, loosen the swing arm’s locking
screw (clamp rail side).
3 Remove the clamp rail’s end cap.
4 Insert the swing arm’s slider into the clamp rail with the “TOP”
label facing up.
5 Attach the end cap to the clamp rail.
6 Attach the supplied clamp base to the desired position on top
of the camera and loosen the clamp rail locking screw.
Use the supplied hex wrench to secure it firmly with the 4 hex
socket head bolts.
7 Remove the end cap from the other arm of the
clamp rail and insert the slider at the front of the
clamp base into the clamp rail.
8 Attach the end cap to the clamp rail.
9 Loosen the other swing arm’s locking screw
(viewfinder side).
10 Adjust the optional viewfinder to the desired position
(up/down, front/back) and fasten all the screws.
Be sure to firmly hold the viewfinder with one hand as
you adjust its position.
Fasten the two locking screws of the swing arm and the
clamp rail locking screw on the clamp base.
,
Preparing the Camera
42
Connecting and Adjusting the Optional Viewfinder
You can adjust the brightness, contrast, color, sharpness, and luminance level of the optional viewfinder. These
adjustments will not affect your recordings.
1 Connect the camera’s VIDEO terminal to the
optional viewfinder’s VIDEO terminal using an
optional UN-5 or UN-10 Unit Cable.
•Align the
Í
marks on the cable’s plugs and the
terminals.
2 Put the unit cable through one of the cable
clamps on the clamp rail.
The clamp rail has 4 screw holes for the cable
clamps so you can adjust their position as needed.
3 Turn on the camera and turn the dioptric adjustment
ring until the viewfinder’s image is sharp.
4 Press the EVF button on the optional viewfinder.
The monitoring menu will open with the [EVF-V70] submenu selected.
Alternatively, you can press an assignable button set to [EVF-V70 Setup] (A 127).
5 Select [Brightness], [Contrast], [Color], [Sharpness] or [Luminance] and then press SET.
6 Select the desired level and then press SET.
Repeat steps 5 and 6 to adjust other settings as necessary.
NOTES
The optional viewfinder displays in color by default. You can set [Monitoring Setup] (
¢
) >
[B&W Image] > [VIDEO Output] to [On] to set the viewfinder to black and white.
By default, the optional viewfinder’s screen will be dimmed automatically when it is not being used. You can
set [Eye Sensor] to [Off] to keep the optional viewfinder’s screen always bright.
When using one of the Canon Log gamma curves, you can apply a LUT to the image displayed on the optional
viewfinder (A 155).
43
Preparing the Camera
Removing the Optional Viewfinder
1 Press the
Q
button to turn off the camera.
2 Disconnect the unit cable from the camera and viewfinder.
3 Remove the end cap from the clamp rail’s arm attached to
the clamp base and loosen the clamp rail locking screw.
4 While pulling out the locking pin at the other side of the
clamp rail, remove the clamp rail from the clamp base.
The slider will stop at the end of the rail. Pull out the locking
pin at the other side of the clamp rail to be able to take the
slider completely out of the rail.
5 Attach the end cap to the clamp rail.
6 If you wish to remove the clamp rail from the optional
viewfinder, repeat steps 3 to 5 with the clamp rail’s arm
attached to the viewfinder.
In that case, loosen the swing arm’s locking screw (clamp rail
side).
Attaching the Microphone Holder
Attach the supplied microphone holder to the desired
position on the handle unit or the top plate of the camera.
Use the supplied hex wrench to secure it firmly with the 2 hex
socket head bolts.
,
Preparing the Camera
44
Preparing the Lens
As much as possible, attach and remove the lens quickly and in a clean environment free of dust. Refer also to
the instruction manual of the lens used.
IMPORTANT
Make sure to turn off the camera before attaching/removing a lens and before connecting/disconnecting a
lens’s 12-pin interface cable to/from the camera’s LENS terminal. Failing to do so can cause a malfunction of
the camera or lens.
When attaching/removing a lens, avoid direct sunlight or strong light sources. Also, be careful not to drop the
camera or lens.
NOTES
After removing a lens/When a lens is not attached to the camera:
- Do not touch the lens’s surfaces, the lens mount or any components inside the lens mount area.
- Place the body cap back on the lens mount and the dust caps back on the lens. Clean any dust or dirt from
the body cap and dust caps before using them.
Zq
Attaching an EF Lens
1 Press the
Q
button to turn off the camera.
2 Turn the mount handle clockwise until it stops.
3 Remove the body cap from the camera and any dust
caps from the lens.
4 Check that the mount handle is at the correct position
for attaching a lens.
5 Align the lens and mount making sure that the index
marks are aligned.
EF lenses: Align the red dot on the lens with the red EF
lens mount index mark on the camera.
EF-S lenses: Align the white square on the lens with
the white EF-S lens mount index mark on the camera.
6 After the lens is attached to the camera, without turning
the lens, turn the mount handle counter-clockwise until it
is tightened firmly.
Only when using a lens with a 12-pin camera interface cable:
7 Connect the lens’s 12-pin cable to the camera’s LENS
terminal.
This allows the camera to power the lens’s drive unit.
8 Press the
Q
button to turn on the camera.
9 If necessary, change the lens’s settings to allow control
from the camera.
Only when using a CN7x17 KAS S/E1 or CN20x50
IAS H/E1 lens: In the lens’s Info screen, set [I/Fprior] to
[Mount].
For details, refer to the instruction manual of the lens
used.
45
Preparing the Camera
Zq
Removing an EF Lens
1Press the
Q
button to turn off the camera.
If the lens is connected to the camera’s LENS
terminal, disconnect the 12-pin cable after turning off
the camera.
2 While holding the bottom of the lens, turn the mount
handle clockwise until it stops.
Make sure not to drop the lens when removing it.
3 Place the body cap back on the lens mount and the
dust caps back on the lens.
NOTES
Turning on the image stabilization function of an EF lens may reduce the effective usage time of the battery.
When image stabilization is not necessary, for example if the camera is fixed to a tripod, it is recommended to
turn it off.
Depending on the lens used, you may experience one or more of the following limitations.
- The lens model name may be shortened when displayed on the screen.
- You may not be able to focus manually when the focus mode switch is set to AF.
- You may not be able to use the focus preset function on super telephoto lenses.
- You may not be able to use the power zoom function on lenses with that function.
This camera’s sensor is larger than the sensor size for which EF-S lenses are designed (APS-C). When using
EF-S lenses with this camera, you may notice peripheral illumination fall-off or vignetting.
When using a compatible lens, you can use the [System Setup] > [Retract Lens] setting to retract
the lens automatically when the camera’s power is turned off.
Zq
Updating the Firmware of an EF Lens
You can update the lens firmware of the EF lens attached to the camera. For details about firmware updates for
EF lenses, visit your local Canon Web site.
1 Download the lens firmware update file from the Canon Web site and save it on an SD card. Insert the SD card
containing the lens firmware update into the SD card slot.
2 Attach the lens you wish to update to the camera and open the lens firmware submenu.
[System Setup] (
B
) > [Firmware] > [Lens]
The current lens firmware version will be displayed.
If the [Lens] option is grayed out, the attached lens may not support firmware updates or the SD card used
may not contain a valid lens firmware file. Check the lens and SD card and repeat the procedure from the
beginning.
3 Press [OK] (camera menu) or select [OK] and press SET (monitoring menu).
4 Select the lens firmware file (file extension .LFU) and then press SET.
5 Press [OK] (camera menu) or select [OK] and press SET (monitoring menu).
The lens firmware will be updated. Once in progress, the lens firmware update cannot be canceled.
6 When the confirmation message appears, press [OK] (camera menu) or press SET (monitoring menu).
Preparing the Camera
46
IMPORTANT
Be sure to observe the following precautions while the lens firmware is being updated. Failing to do so can
cause malfunctions.
- Do not remove the power source or turn off the camera.
- Do not remove the lens.
- Do not operate any buttons or controls on the camera.
- Do not open the SD card slot cover and do not remove the SD card.
NOTES
We recommend that you power the camera from a power outlet using an AC adapter or use a sufficiently
charged battery.
When using an optional EF extender, remove the extender before performing the procedure.
[]r
Attaching a PL Lens
1 Press the
Q
button to turn off the camera.
2 Hold a bayonet ring handle and turn the bayonet ring
counter-clockwise to remove the body cap and remove any
dust caps from the lens.
3 Attach the lens to the camera aligning a groove on the lens
with the PL lens index pin on the mount.
4 Turn the bayonet ring clockwise to fix the lens in place.
Only when using a lens with a 12-pin camera interface cable:
5 Connect the lens’s 12-pin cable to the camera’s LENS
terminal.
This allows the camera to power the lens’s drive unit.
6 Press the
Q
button to turn on the camera.
7 If necessary, change the lens’s settings to allow control
from the camera.
For details, refer to the instruction manual of the lens
used.
NOTES
When a B4 lens is attached to the camera (using the optional MO-4E or MO-4P B4 Mount Adapter)
- Set [Camera Setup] > [Sensor Mode] to [Super 16mm (Cropped)]. Next, set [Camera
Setup] > [Mount Adapter] to [MO-4E] (
Zq
) or [MO-4P] (
[]r
).
- If you connect the lens’s 12-pin camera interface cable to the camera’s LENS terminal, you will be able to
zoom and use the push auto iris function from the camera.
- When using a B4 lens compatible with the L.C.A.C. (automatic lens chromatic aberration correction)
function, if the 12-pin interface cable is connected to the camera, the lens’s chromatic aberration can be
corrected. In such case, will appear at the left of the monitoring screen.
PL lens index pin
47
Preparing the Camera
[]r Removing a PL Lens
1Press the
Q
button to turn off the camera.
If the lens is connected to the camera’s LENS terminal,
disconnect the 12-pin cable after turning off the camera.
2 Turn the bayonet ring handles counter-clockwise.
3 Remove the lens and place the body cap back on the lens
mount and the dust caps back on the lens.
In-Camera Lens Correction
Depending on the characteristics of the lens used, the corners of an image frame may be darker than the center
due to light fall-off (peripheral illumination drop), or color shift/color fringing may be visible along high-contrast
edges in the image (chromatic aberration). If the camera has correction data available for the lens used, it can
apply this correction data to compensate as necessary.
Peripheral illumination correction is available for EF lenses. Chromatic aberration correction is available for EF
lenses and broadcast lenses, including automatic correction for broadcast lenses compatible with L.C.A.C
(A 46).
1 Attach the lens you want to use.
2 Open the desired correction screen.
[Camera Setup] (
v
) > [Periph. Illum. Corr.] or [Chrom. Aberr. Corr.]
If correction data is not available, or if the broadcast lens attached is not compatible with L.C.A.C., the
corresponding menu option will appear grayed out. In the case of an EF lens, visit your local Canon Web site
and check if there is correction data available for the lens you are using. If so, download the necessary
update package and upgrade the camera’s firmware following the instructions supplied therein.
3 Select [On] and then press SET.
As long as [Periph. Illum. Corr.] or [Chrom. Aberr. Corr.] is set to [On], the camera will automatically apply the
appropriate correction data.
NOTES
About in-camera lens correction data: The camera contains a register of correction data for compatible EF lenses
that were available at the time the camera went on sale. Correction data for future lenses will be made
available as part of the regular updates released for the camera’s firmware. For more details, visit your local
Canon Web site.
No peripheral illumination/chromatic aberration correction will be applied in the following cases:
- When the appropriate correction data is not available for the EF lens attached.
- When using non-Canon lenses. Even if the corresponding menu setting is available (not grayed out), setting
it to [Off] is recommended.
When peripheral illumination correction is activated:
- Depending on the recording conditions, noise may appear in the periphery of the image as a result of the
correction.
- The level of correction will be lower for lenses that cannot provide distance information.
- The level of correction will be lower the higher the ISO speed/gain setting used.
- Due to the difference in sensor size, when using EF-S lenses, peripheral illumination fall-off may be more
pronounced.
Preparing Recording Media
48
Preparing Recording Media
The camera records main recording clips (XF-AVC or ProRes) and sub recording clips (XF-AVC Intra) on CFast
cards, and sub recording proxy clips (XF-AVC Proxy) and photos on SD cards*. The camera features two CFast
card slots. When you insert two CFast cards in the camera, the camera can record 4K clips simultaneously on
both cards, or it can switch automatically to recording on the other CFast card when a CFast card becomes full.
Initialize recording media (A 51) when you use them with this camera for the first time.
* The SD card is used also to save custom picture files, menu settings files and user memo files created with the Canon XF Utility
software (A 161) for later use on the camera.
Compatible Recording Media
The following types of memory card can be used with this camera. For the latest information about recording
media tested for use with this camera, visit your local Canon Web site.
CFast cards
CFast 2.0-compliant cards.
SD cards*
*
As of May 2018, the clip recording function has been tested using SD cards made by Panasonic, Toshiba and SanDisk.
**
SD Speed Class is a standard that indicates the minimum guaranteed data transfer rate of SD cards.
IMPORTANT
CFast cards can become hot due to the high operating temperature inside the camera. Removing a CFast
card immediately after using it for recording may cause burns or cause you to drop the CFast card, resulting in
damage to the card.
After repeatedly recording, deleting and editing clips (if the memory is fragmented), you may notice slower
writing speeds to the recording media and recording may even stop. In such case, save your recordings and
initialize the recording media with the camera (using the [Complete] initialization option for SD cards). Be sure
to initialize recording media especially before shooting important scenes.
About CFast and SDXC cards: You can use CFast and SDXC cards with this camera but these types of cards are
initialized by the camera using the exFAT file system.
- When using exFAT-formatted cards with other devices (digital recorders, card readers, etc.), make sure that
the external device is compatible with exFAT. For more information on compatibility, contact the computer,
operating system or memory card manufacturer.
- If you use exFAT-formatted cards with a computer OS that is not exFAT-compatible, you may be prompted
to format the card. In such case, cancel the operation to prevent data loss.
NOTES
Proper operation cannot be guaranteed for all recording media.
SD card type:
SD cards SDHC cards SDXC cards
SD Speed Class**:
49
Preparing Recording Media
Inserting a CFast Card
You can insert a CFast card into CFast card slot A or slot B. If you have two CFast cards, you can use both slots.
1 Slide the CFast card slot cover switch in the direction of the
arrow.
The CFast card slot cover will open upward (slot A) or
downward (slot B).
2 Insert the CFast card straight, with the label facing up, all
the way into the slot.
3 Close the CFast card slot cover.
Do not force the cover closed if the CFast card is not correctly
inserted.
CFast card access indicators
If you set [System Setup] > [LED] > [Media Access] to [Off], the card access indicators will not
illuminate.
Removing a CFast card
1 To remove the CFast card currently selected, wait until the CFast
card access indicator is illuminated in green.
A CFast card not currently selected (CFast card access indicator is
off) can be removed at any time.
2 Slide the CFast card slot cover switch in the direction of the
arrow.
The CFast card slot cover will open upward (slot A) or downward
(slot B).
The card access indicator will illuminate in red momentarily. Wait until the indicator is off.
3 Push the CFast card release button.
4 Pull out the CFast card and close the CFast card slot cover.
CFast /CFast
indicator
CFast card status
Red Accessing the CFast card.
Green
Recording/playback is possible and the CFast card slot is
selected for recording/playback.
Off
A CFast card is not inserted or the CFast card slot is not
currently selected.
CFast /CFast
indicator
Preparing Recording Media
50
IMPORTANT
Observe the following precautions while a CFast card access indicator is illuminated in red. Failure to do so
may result in permanent data loss.
- Do not remove the power source or turn off the camera.
- Do not open the cover of the CFast card slot being accessed.
Inserting and Removing an SD Card
1 Wait until the SD card access indicator is off or is illuminated in
green.
2 Slide the SD card slot cover switch in the direction of the arrow.
The SD card slot cover will open to the left.
3 Insert the SD card straight, with the label toward the back of
the camera, all the way into the SD card slot until it clicks.
To remove the SD card, wait until the access indicator is off and
then push the SD card once to release it. When the SD card
springs out, pull it all the way out.
4 Close the SD card slot cover.
Do not force the cover closed if the SD card is not correctly inserted.
SD card access indicator
If you set [System Setup] > [LED] > [Media Access] to [Off], the card access indicators will not
illuminate.
IMPORTANT
Observe the following precautions while the SD card access indicator is illuminated in red. Failure to do so may
result in permanent data loss.
- Do not remove the power source or turn off the camera.
- Do not remove the SD card.
SD cards have front and back sides that are not interchangeable. Inserting an SD card facing the wrong
direction can cause a malfunction of the camera. Be sure to insert the SD card as described in step 3.
NOTES
SD cards have a physical switch to prevent writing on the card so as to avoid the accidental erasure of the
card’s content. To write-protect the SD card, set the switch to the LOCK position.
SD card access indicator SD card status
Red Accessing the SD card.
Green
Simultaneous sub recording of XF-AVC Proxy clips is
activated and the SD card is ready for recording, or
playback of XF-AVC Proxy clips and photos is possible.
Off
An SD card is not inserted, the SD card is not being
accessed, or the SD card is write-protected with the LOCK
switch.
SD card access indicator
51
Preparing Recording Media
Initializing Recording Media
The first time you use a recording media with this camera, initialize it first. You can also initialize a recording
media to permanently delete all the data it contains. For details about initializing the CDX-36150 Recorder’s
Capture Drive, refer to
Initializing a Capture Drive
(A 205).
When initializing an SD card, you can select quick initialization, which clears the file allocation table but does not
physically erase the stored data, or complete initialization, which deletes all data completely.
1 Open the [Initialize Media] submenu.
[Rec/Media Setup] (
3
) > [Initialize Media]
Alternatively, you can press an assignable button set to [Initialize Media] (A 127).
2 Select [CFast A], [CFast B] or [SD Card] and then press SET.
To initialize a CFast card
3 Camera menu: Press both [FORMAT] buttons simultaneously.
Monitoring menu: Select [OK] and then press SET.
The CFast card is initialized and all the data it contains is erased.
4 When the confirmation message appears, press [OK] (camera menu) or press SET (monitoring
menu).
To initialize an SD card
3 Select [Complete] (complete initialization) or [Quick] (quick initialization) and then press SET.
4 Camera menu: Press both [FORMAT] buttons simultaneously.
Monitoring menu: Select [OK] and then press SET.
The SD card is initialized and all the data it contains is erased.
If you are using the [Complete] initialization option, press [CANCEL] (camera menu) or press SET (monitoring
menu) to cancel the operation while it is in progress. You can use the SD card but all data will be erased.
5 When the confirmation message appears, press [OK] (camera menu) or press SET (monitoring
menu).
IMPORTANT
Initializing a recording media will permanently erase all data, including clips with an
$
mark, photos and
protected custom picture files. Lost data cannot be recovered. Make sure you save important recordings in
advance.
Be sure to observe the following precautions while the initialization is in progress. Failing to do so may result in
permanent data loss.
- Do not remove the power source or turn off the camera.
- Do not open the card slot cover of the recording media being initialized and do not remove the recording
media.
Depending on the SD card, the complete initialization may take up to a few minutes.
NOTES
While recording on a CFast card, you can initialize another CFast card in the other CFast card slot.
Preparing Recording Media
52
Switching Between the CFast Card Slots
The camera features two CFast card slots, CFast (CFast card
slot A) and CFast (CFast card slot B). If both slots contain a
CFast card, you can switch between them as necessary.
Press the SLOT SEL. button.
The access indicator of the selected CFast card slot will illuminate
in green. On the HOME screen and at the bottom left of the
monitoring screen, the CFast card currently selected is indicated
with a Ð mark next to the CFast card icon.
NOTES
If both CFast card slots contain a CFast card and you open the cover of the selected slot, the camera will
automatically switch to the other slot.
You cannot use the SLOT SEL. button to switch between CFast card slots while recording.
You can also perform this function remotely using Browser Remote on a connected network device
(
A
170, 174).
Relay Recording and Double Slot Recording
The camera features two convenient recording methods that can be used when both CFast card slots contain a
CFast card: double slot recording and relay recording (XF-AVC clips only).
Double slot recording: This function records the same clip simultaneously to both CFast cards, which is a
convenient way to make a backup copy of your recording while you record.
Relay recording: When the main recording format is set to [XF-AVC (CFast)], this function allows you to continue
recording on another CFast card without interruption if the CFast card you are using becomes full. Relay
recording is available from CFast card slot A to CFast card slot B, and vice versa.
To use double slot recording
1 Open the [Double Slot Rec] submenu.
[Rec/Media Setup] (
3
) > [Double/Relay Rec] > [Double Slot Rec]
2 Select [On] and then press SET.
4
appears on the HOME screen and at the bottom left of the monitoring screen.
To use relay recording
1 Open the [Relay Recording] submenu.
[Rec/Media Setup] (
3
) > [Double/Relay Rec] > [Relay Recording]
2 Select [On] and then press SET.
NOTES
Relay recording is disabled (the camera will not switch to the other CFast card) when slow & fast motion
recording is activated.
If a CFast card becomes full during double slot recording, recording on both cards will stop. On the other
hand, if an error occurs with one of the CFast cards, recording will continue on the other card.
Double slot recording cannot be used together with relay recording or slow & fast motion recording.
qr
Double slot recording is not available when the main recording format is set to [RAW
( Capture Drive)], the sensor mode is set to [Full Frame], and the frame rate is set to 59.94P or 50.00P.
53
Preparing Recording Media
Checking the Remaining Recording Time on Recording Media
The recording media icons and the approximate remaining recording time* (in minutes) on each card are
displayed on the HOME screen and at the bottom left of the monitoring screen. Additionally, on the
[MEDIA] screen (A 218), you can check the total space, used space, and remaining recording time* on each
recording media.
* The approximate available recording time is based on the current bit rate (A 65).
Recovering Clips
Some actions, such as suddenly turning off the camera or removing the recording media while data is being
recorded, can cause data errors in the recorded XF-AVC or ProRes clip. If an error message appears in the
[LIVE] screen indicating that clips need recovering, you may be able to recover XF-AVC clips with data
errors with the following procedure.
1 Press the PLAY button and select the recording media that contains the clip that needs to be
recovered (A 142).
Select [CFast (XF-AVC)], [CFast (ProRes)] or [SD Card (XF-AVC)] as the playback media/format. In the case
of a CFast card, select the correct CFast card slot.
2 Press [CLIP LIST] to open the list of clips.
3 Turn the SELECT dial to find the clip that needs to be recovered and then press SET.
The message [Clip requires data recovery] appears instead of the clip details.
4 Open the recovery screen.
[OPTIONS] > [Recover Clip]
5 Press both [RECOVER] buttons simultaneously.
The camera will attempt to recover the corrupted data.
NOTES
This procedure may delete XF-AVC clips shorter than 0.5 seconds in length.
In some cases, it may not be possible to recover the data. This is more likely when the file system is corrupted
or the recording media is physically damaged.
Only clips recorded with this camera can be recovered. Photos cannot be recovered.
Adjusting the Black Balance
54
Adjusting the Black Balance
You can have the camera adjust the black balance automatically when the ambient temperature changes
considerably or if there is a noticeable change in a true black video signal.
1 Attach the body cap to the lens mount.
If a lens was attached, turn off the camera and remove the lens. Place the body cap back on the lens mount
and turn on the camera.
2 Open the [ABB] screen.
[Camera Setup] > [ABB]
Complete the procedure following the messages on the cameras control display.
3 Press [OK].
The automatic black balance procedure will start. It will take approximately 50 seconds (
q
r
) or 40 seconds (
Z[]
).
During the procedure, the monitoring screen will turn black.
4 When the confirmation message appears, press [OK].
If the sensor is not completely shielded from light, [Error] will appear on the control display. Press [OK] and
repeat the procedure from the beginning.
NOTES
Adjusting the black balance is necessary in the following cases:
- When using the camera for the very first time or after a long period of not using it.
- After sudden or extreme changes in ambient temperature.
- After changing the ISO speed/gain settings.
- After changing the sensor mode.
- After resetting all the camera’s settings.
During the adjustment of the black balance, you may notice some irregular displays appear on the monitoring
screen. This is not a malfunction.
3
55
Recording
Recording Video
This section explains the basics of recording clips*. Before making important recordings for the first time, make
test recordings using the video configuration(s) you plan to use to check that the camera operates correctly.
Should the camera fail to operate correctly, refer to
Troubleshooting
(A 219).
* “Clip” refers to a single movie unit recorded with a single recording operation. Some clips can include custom picture settings
(A 131) and metadata (A 118).
Recording
1 Press the Q button to turn on the camera.
The camera turns on in record standby mode.
The access indicators of card slots with a card inserted will illuminate momentarily in red. Then, the access
indicator of the CFast card slot selected for recording will change to green.
2 Press the REC button to begin recording.
Recording starts. The recording indicator on the HOME screen and at the bottom of the monitoring screen
changes from [STBY] to [
Ü
REC]. While recording on a CFast card, the tally lamp will illuminate in red.
You can also perform this function remotely using Browser Remote on a connected network device (
A
170,
174).
For details about sub recordings refer to
Simultaneous Sub Recordings
(A 71).
3 Press the REC button to stop recording.
The clip is recorded to the recording media and the camera returns to record standby mode. The tally lamp
will change back to green.
CFast card access
indicators
Tally la m p
SD card access
indicator
Ta l l y l a m p
Recording Video
56
IMPORTANT
Observe the following precautions while an access indicator is illuminated in red. Failure to do so may result in
permanent data loss.
- Do not open the card slot cover of the card being accessed and do not remove the card.
- Do not remove the power source or turn off the camera.
Be sure to save your recordings regularly (A 161), especially after making important recordings. Canon shall
not be liable for any loss or corruption of data.
NOTES
NOTES
If the power supplied to the camera is at or below the level set for the power level warning (A 199), the
camera will not start recording.
If you record XF-AVC clips using the custom picture and metadata settings, those settings will be recorded
with the XF-AVC clip. For more details, refer to
Custom Picture Settings
(A 131) and
Using Metadata
(A 118).
If the camera switches to the other CFast card while recording video due to the relay recording function
(A 52), the two parts (before/after the switch) will be recorded as separate clips.
A single XF-AVC clip can be recorded continuously for up to 6 hours. At that point, a new clip will be created
automatically and recording will continue on a separate clip.
You can use the [System Setup] > [Rec Operation Beep] setting to make the camera emit a sound
when you start/stop recording.
If you set an assignable button to [Add
$
Mark] or [Add
%
Mark] (A 127), you can press the button to add
an
$
mark or
%
mark to the last XF-AVC clip recorded.
When you use a commercially available lens adapter and the image on the screen is inverted, you can use the
[System Setup] > [Scan Reverse Rec] > [Setting] setting to return the image to the correct
orientation.
Key lock: Locking the camera’s controls
To activate the key lock function, press and hold the C button. After the countdown that appears on the
control display ends, all the physical controls (buttons, switches, etc.) will be locked except for the Q,
REC and C buttons*. This is useful in preventing settings from being changed due to inadvertently pressing
the camera’s buttons and controls. Press and hold the C button again for about 3 seconds to reactivate the
controls.
Even when the camera’s controls are locked, you can operate the camera using Browser Remote (A
170
),
an optional RC-V100 Remote Controller connected to the camera (A 123) or the controls on the lens. When
an optional OU-700 Remote Operation Unit is connected to the camera, you can select whether its controls
are locked along with those of the camera with the [System Setup] > [
C
Button] setting.
* You can also choose to lock the REC buttons using the [System Setup] > [REC Button] setting.
57
Recording Video
Onscreen Displays on the HOME Screen
Refer to this section for an explanation of the various controls and onscreen displays on the HOME screen,
which appears on the camera’s control display.
Screen buttons
Information area (by groups, from left to right, top to bottom)
Icon/Display Description
000.00, 000 Frame rate (A 65)
When slow & fast motion recording is activated, the shooting frame rate is displayed as an integer
instead (A 68).
F0.0 / F00, T0.0 / T00, closed
00 stops
Aperture value (A 79) and ND filter setting (A 78)
000.00°, 1/0000, 000.00Hz Shutter speed (A 74)
000000, 00.0 dB ISO speed/Gain (A 76)
Canon Log 3, Canon Log 2, Canon Log,
Wide DR, Normal 1 to Normal 4
[Gamma] setting in the custom picture file (A 134)
C.Gamut, BT.2020, DCI-P3, BT.709 [Color Space] setting in the custom picture file (A 134)
, 0000±0 White balance (A 86)
Icon/Display Description
TC 00:00:00.00, TC 00:00:00:00 Time code (A 101)
Depending on the operation, a letter may appear after the time code (A 102).
U
Genlock (A 106)
Recording operation:
STBY,
Ü
REC Clip recording: record standby, recording.
S&F STBY,
Ü
S&F REC Slow & fast motion recording (A 68): record standby, recording.
` Output recording command (A 193): in white – record standby, in red – recording.
4
Double slot recording (A 52)
, ,
and
,
Network connection status (A 169)
Recording Video
58
Recording media status for the main recording ([Main]) and sub recording ([Sub])
, ,
8
, and 0000 min,
SDI-OUT RAW
Recording media: in green – can record; in white – reading the recording media; in yellow* – the
recording media is almost full. The CFast card selected for recording is indicated with a
Ð
mark.
*
//
8
only.
, ,
9
, (in red) No recording media or cannot record on the recording media.
0000x0000 Resolution (A 66)
00.00P, 00.00i Frame rate (A 65)
XF-AVC(YCC), XF-AVC(RGB),
ProRes(YCC), ProRes(RGB), RAW
Main recording format (A 65)
Audio level indicators CH1 to CH4 (A 111)
æ
Audio limiter (A 111)
REEL A000 Camera index/reel number (A 62)
CLIP C000 Clip number (A 62)
DC IN 00.0V, BATT 00.0V
(000%)
()
Power supply voltage (DC IN and battery) (A 26): in red – low power warning. : Appears when
the power supply is connected to the CDX-36150 Recorder.
The power source currently in use is indicated with a
Ð
mark.
The percentage is displayed only when using a battery compatible with BMS (battery management
system).
C
Key lock (A 56)
b
Temperature warning (A 64)
(in yellow) The INFO icon appears when there is an important notice or error message in the [LIVE]
screen (A 215).
GPS signal (A 120): continuously on – satellite signal acquired; flashing – satellite signal not
acquired.
Displayed only when an optional GP-E1 GPS Receiver is connected to the camera.
{
(in green), (in red)
Photo recorded (A 125) or no photo can be recorded.
Icon/Display Description
59
Recording Video
Onscreen Displays on the Shooting Screen
Refer to this section for an explanation of the various onscreen displays that appear on the shooting screen that
is displayed on monitoring devices (optional viewfinder or external monitors). You can use the custom display
function (A 139) to turn off individual onscreen displays if they are not required. The menu item that controls
each display is given in the following table (1: indicates a menu item under [Custom Display 1] and 2: indicates a
menu item under [Custom Display 2]).
Zq
AF frames
Depending on the focus function used you may see some of the following AF frames.
Continuous AF frame – always in white (A 94)
AF-Boosted MF frame – in yellow: manual adjustment range; in white: automatic adjustment range (A 93)
One-shot AF frame (A 92)
Face AF: Main subject (A 96)
Face AF:
Other face detection frames
Tracking: Subject selection (A 97)
Tracking: During tracking
Recording Video
60
Left side of the screen
Top of the screen
Icon/Display Description Custom Display
0000 mm Approximate focal length of the lens 1: [Focal Length]
C
Key lock (A 56) 1: [Key Lock]
, ,
and ,
Network connection status (A 169) 2: [Network Functions]
GPS signal (A 120): continuously on - satellite signal acquired; flashing - satellite
signal not acquired.
Displayed only when an optional GP-E1 GPS Receiver is connected to the camera.
2: [GPS]
Z[qr
Flash band correction (A 75) 1: [Flash Band Corr.]
, B4 mount adapter (A 191) 1: [Mount Adapter]
Automatic lens chromatic aberration correction for broadcast lenses (A 46)
A
,
@
Zq
Focus mode (A 89) 1: [Focus Mode]
,
Zq
Face AF (A 96)
, , ,
, , ,
,
[Gamma] setting in the custom picture file (A 134) 1: [Custom Picture]
, , , [Color Space] setting in the custom picture file (A 134)
Editing of the custom picture file’s detailed settings ([Other Settings] > [Activate]) is
enabled (A 135).
, Light metering mode (A 82) 1: [Light Metering]
b
Temperature warning (A 64) 2: [Temperature/Fan]
`
Fan operation (A 64)
i
(in red)
Zq
Lens error warning (A 220) 1: [Lens]
(in red) Lithium button battery not inserted (A 24) 2: [DC IN / Battery]
A viewing LUT has been applied to at least one video output (A 155)
The icon will appear on all active display devices regardless of the video output to
which the LUT was applied.
1: [LUT]
Icon/Display Description Custom Display
FPS, S&F FPS,
000.00, 000
Frame rate (A 65)
When slow & fast motion recording is activated, the shooting frame rate ([S&F FPS])
is displayed as an integer instead (A 68).
2: [Frame Rate]
E
, F0.0 / F00, T0.0 / T00,
closed
Aperture value (A 79)
[]r
Only displayed when an EF Cinema lens
compatible with aperture adjustment from the camera (A 240), a compatible
broadcast lens, or a PL lens compatible with Cooke's /i Technology metadata
protocol is attached to the camera.
1: [Iris]
00 stops ND filter (A 78) 1: [ND Filter]
000.00°, 1/0000,
000.00Hz
Shutter speed (A 74) 1: [Shutter]
ISO 000000, GAIN 00.0dB ISO speed/Gain (A 76) 1: [ISO/Gain]
,
Å
A,
Å
B,
¼, É, to and
00000K ±00
White balance (A 86) 1: [White Balance]
61
Recording Video
Right side of the screen
Bottom of the screen
DC IN 00.0V,
BATT 00.0V
Power supply voltage (DC IN and battery) (A 26)
The power source currently in use is indicated with a
Ð
mark.
2: [DC IN / Battery]
A to Z
Camera index (A 63) 2: [Camera Index]
Exposure bar (A 82)
Only displayed when the gain, aperture and shutter are all set to manual
adjustment.
1: [Exposure]
AE ±0.00 AE Shift (A 82)
Icon/Display Description Custom Display
{
(in green),
(in red)
Photo recorded (A 125) or no photo can be recorded. 2: [Remaining Photos]
T
(in red) Output onscreen displays (A 154)
The icon can appear in the VIDEO area (optional viewfinder) or in the MON./HDMI
area (external monitors).
2: [OSD Output]
J
,
K
(in yellow)
Peaking (A 91)
The icon can appear in the VIDEO area (optional viewfinder) or in the MON./HDMI
area (external monitors).
1: [Peaking]
^
(in yellow),
(in red)
Magnification (A 92)
The icon can appear in the VIDEO area (optional viewfinder) or in the MON./HDMI
area (external monitors).
1: [Magnification]
æ
,
Audio limiter (A 111) 2: [Audio Lvl Indicator]
Audio level meter and monitor channels (A 111, 160)
Icon/Display Description Custom Display
4
Double slot recording (A 52) 2: [Recording Mode]
Camera level (A 40) 2: [Level]
Headphone volume (A 143)
Recording media status and estimated remaining recording time 2: [Remaining Rec Time]
, ,
8
and
0000 min
Recording media status: in green - can record; in white - reading the recording media;
in yellow - the recording media is almost full. The CFast card selected for recording is
indicated with a
Ð
mark.
, ,
9
(in red)
No recording media or cannot record on the recording media.
Capture Drive status
0000 min In green – can record; In white – reading the Capture Drive.
(in red) No Capture Drive inserted or cannot record on the Capture Drive.
Recording operation: 2: [Recording Mode]
STBY,
Ü
REC Clip recording: record standby, recording.
S&F STBY,
Ü
S&F
REC
Slow & fast motion recording (A 68): record standby, recording.
`
Output recording command (A 193): in white – record standby, in red – recording. 2: [Rec Command]
Icon/Display Description Custom Display
Recording Video
62
NOTES
NOTES
You can use the [Monitoring Setup] > [Surrounding Area] settings to show on the monitoring
screen more of the periphery around the area that is actually recorded by the camera.
You can use the [Monitoring Setup] > [OSD Output] > [VIDEO] or [MON.+HDMI] > [Peripheral
Border] setting to change whether the camera’s onscreen displays appear on the image or in the margins
around the image (the default setting).
You can also choose not to output the onscreen displays to monitoring devices (A 154).
Setting the Clip File Name
The camera allows you to change several settings that determine the file name of the recorded clips. Personalize
the clip file name according to your preferences or organizational conventions to create files that are easier to
identify and organize.
The basic file name structure is as follows. When the simultaneous sub recording of XF-AVC Proxy clips is
activated, the file names of the main and sub recording clips will be identical for the most part (components
1 to 6).
A001C001 to Z999D999 Clip identification. Includes the camera index, reel number and clip number
components of the clip file name (A 62).
2: [Reel/Clip Number]
00:00:00.00, 00:00:00:00 Time code (A 101)
Depending on the operation, a letter may appear after the time code (A 102).
2: [Time Code]
U
Genlock (A 106) 2: [Genlock]
Icon/Display Description Custom Display
A001C001_yymmddXX_CANON_01P
1 2 3 4 675
1 Camera index: One character (A to Z) that
identifies the camera used.
2 Reel number: 3 characters (001 to 999) that
identify the recording media used. The number is
assigned automatically but you can set the initial
number. After you insert a new recording media
(one that was just purchased or initialized), the
number advances by one when the first recording
is made.
3 Clip number: 4 characters (C001 to D999). The
clip number advances automatically with each
clip recorded (switching to D001 after C999), but
you can set the initial clip number and select the
clip numbering method.
4 Recording date (set automatically by the camera).
5 Random component: 2 characters (numbers 0 to
9 and capital letters A to Z) that change randomly
with each clip.
6 User defined field: 5 characters (numbers 0 to 9
and capital letters A to Z) for any other
identification purposes.
7 The camera will automatically add the suffix “_P”
to the file name of XF-AVC Proxy clips.
Additionally, when an SDHC card is used to
record XF-AVC Proxy clips, a stream number (01
to 99) will be added before the “P”. The stream
number will advance every time the video (stream)
file within the clip is split and recording continues
on a separate stream file.
63
Recording Video
Setting the components of the clip file name
To set the camera index
1 Open the [Camera Index] screen.
[Rec/Media Setup] (
3
) > [Metadata] > [Camera Index]
2 Turn the SELECT dial to select the desired camera index.
3 Press [OK] (camera menu) or press SET twice (monitoring menu).
To set the clip numbering method
1 Open the [Clip Numbering] screen.
[Rec/Media Setup] (
3
) > [Metadata] > [Clip Numbering]
2 Select [Reset] or [Continuous] and then press SET.
Options
[Reset]: Clip numbers will restart from 001 every time you insert a new recording media.
[Continuous]: Clip numbers will start from the initial number set with [Clip Number] (following procedure) and
continue across different recording media.
To set the reel number or initial clip number
The initial clip number can only be set when [Clip Numbering] is set to [Continuous].
1 Open the [Reel Number] or [Clip Number] screen.
[Rec/Media Setup] (
3
) > [Metadata] > [Reel Number] or [Clip Number]
2 Monitoring menu only: Select [Set] and then press SET.
To reset the reel/clip number to [001], select [Reset] instead.
3 Set the desired reel/clip number using the keyboard screen (A 37).
Camera menu only: Press [RESET] to reset the reel/clip number to [001].
NOTES
NOTES
If XF-AVC clips and ProRes clips are recorded on the same recording media, their reel numbers will differ.
To set the user-defined field
1 Open the [User Defined] screen.
[Rec/Media Setup] (3) > [Metadata] > [User Defined]
2 Set the desired text/number using the keyboard screen (A 37).
Camera menu only: Press [RESET] to reset the user-defined field to [CANON].
Recording Video
64
Using the Fan
The camera uses an internal cooling fan to reduce the camera’s internal heat. In shooting mode, you can change
the fan’s operation mode and speed. In playback mode, the fan runs at all times but you can select its speed.
Setting the Fan’s Operation in Shooting Mode
In addition to the fan’s operation mode, you can select independently the fan speed used while recording and in
record standby mode.
1 Open the fan’s [Mode] submenu.
[System Setup] (B) > [Fan] > [Mode]
2 Select the desired option and then press SET.
If you selected [Automatic]:
3 To set the fan speed to be used while recording, select [Fan Speed (REC)] and then press SET.
4 Select the desired fan speed and then press SET.
Repeat steps 3 and 4, selecting [Fan Speed (STBY)] to set the fan speed in record standby mode.
The [Maximum] option offers the maximum cooling effect but is available only for [Fan Speed (STBY)], as it is
noisier.
If you selected [Always On]:
3 Select [Fan Speed (Always)] and then press SET.
4 Select the desired fan speed and then press SET.
Options
[Automatic]: The fan runs while the camera is not recording and is automatically turned off while the camera
is recording. However, if the internal temperature of the camera is too high (
b
appears in red on
the HOME screen and at the left of the monitoring screen), the fan will be activated automatically
(in that case,
`
will appear under the
b
icon on the monitoring screen only). When the
camera’s temperature has decreased sufficiently, the fan will be turned off. Use this setting when
you do not want the camera to pick up the fan’s operating sound.
[Always On]: The fan runs at all times.
Setting the Fan Speed in Playback Mode
1 Press the PLAY button to open the playback control screen.
2 Open the [Fan Speed] submenu.
[System Setup] (B) > [Fan Speed]
3 Select the desired fan speed and then press SET.
IMPORTANT
While the fan is running, the exhaust vent will emit warm air.
Be careful not to obstruct in any way the fan’s air vents (A 14).
NOTES
NOTES
Depending on the ambient temperature and other shooting conditions, the fan may not turn off even if you set
its operating mode to [Automatic].
65
Video Configuration: Video Format, Sensor Mode, System Frequency, Frame Rate, Resolution and Bit Rate
Video Configuration: Video Format, Sensor Mode, System
Frequency, Frame Rate, Resolution and Bit Rate
With the following procedures you can set the video configuration used for main recording clips recorded on a
CFast card in the camera. Select the video format, resolution (frame size) and color sampling settings, bit rate
and frame rate that best match your creative needs. If necessary, you can also select the sensor mode. Available
options for some settings may change depending on previous selections for other settings. See the tables
following the procedures for a summary.
For details about the video configuration of sub recordings (XF-AVC Intra or XF-AVC Proxy clips), refer to
Simultaneous Sub Recordings
(A 71). For available video configurations when using a CDX-36150 Recorder
docked with the camera, refer to
Recording with the CDX-36150 Recorder
(A 206). For available video
configurations when using an external recorder connected to one of the SDI OUT terminals, refer to
Video
Output Configuration
(A 149).
Selecting the Main Recording Format
1 Open the [Main Rec Format] submenu.
[Rec/Media Setup] (3) > [Main Rec Format]
Alternatively, using the HOME screen: [S&F FPS] > [OPTIONS] > [Main Rec Format].
2 Select [XF-AVC (CFast)] or [ProRes (CFast)] and then press SET.
Selecting the Sensor Mode
This allows you to select the image area used by the CMOS sensor. Based on your selection, available video
configuration options will differ. When using the optional MO-4E or MO-4P B4 Mount Adapter, or to shoot in slow
& fast motion recording mode using a cropped frame, make sure to select [Super 16mm (Cropped)].
1 Open the [Sensor Mode] submenu.
[Camera Setup] (
v
) > [Sensor Mode]
Alternatively, using the HOME screen: [S&F FPS] > [OPTIONS] > [Sensor Mode].
2 Select the desired option and then press SET.
Selecting the System Frequency
1 Open the [System Frequency] submenu.
[Rec/Media Setup] (3) > [System Frequency]
Alternatively, using the HOME screen: [S&F FPS] > [OPTIONS] > [System Frequency].
2 Select the desired option and then press SET.
The camera will reset and restart in the selected mode.
Selecting the Frame Rate
This procedure is not necessary when the system frequency is set to [24.00 Hz].
1 Open the [Frame Rate] submenu.
[Rec/Media Setup] (3) > [Frame Rate]
Alternatively, using the HOME screen: [S&F FPS] > [OPTIONS] > [Frame Rate].
2 Select the desired option and then press SET.
Video Configuration: Video Format, Sensor Mode, System Frequency, Frame Rate, Resolution and Bit Rate
66
Selecting the Resolution and Color Sampling Settings
1 Open the [Resolution/Sampling] submenu.
[Rec/Media Setup] (3) > [Resolution/Sampling]
Alternatively, using the HOME screen: [S&F FPS] > [OPTIONS] > [Resolution/Sampling].
2 Select the desired option and then press SET.
Selecting the Bit Rate
1 Open the [Bit Rate] submenu.
[Rec/Media Setup] (3) > [Bit Rate]
Alternatively, using the HOME screen: [S&F FPS] > [OPTIONS] > [Bit Rate].
2 Select the desired option and then press SET.
Available sensor modes by camera model
Available video configuration settings (XF-AVC)
Sensor mode
qr
Z[]
Full frame Ü
Super 35mm Ü
Super 35mm (cropped) Ü
Super 16mm (cropped) Ü Ü
Sensor mode Resolution and color sampling Bit rate and compression
1
System frequency/Frame rate
59.94 Hz
59.94P 59.94i
2
29.97P 23.98P
Full frame
Super 35mm
Super 35mm (cropped)
4096x2160
3840x2160
YCbCr 4:2:2, 10 bit
810 Mbps, Intra-frame Ü –––
410 Mbps, Intra-frame ÜÜ
2048x1080
1920x1080
RGB 4:4:4, 12 bit
440 Mbps, Intra-frame Ü –––
225 Mbps, Intra-frame ÜÜ
RGB 4:4:4, 10 bit
410 Mbps, Intra-frame Ü –––
210 Mbps, Intra-frame ÜÜ
Full frame
Super 35mm
Super 35mm (cropped)
Super 16mm (cropped)
2048x1080
1920x1080
YCbCr 4:2:2, 10 bit
310 Mbps, Intra-frame Ü –––
160 Mbps, Intra-frame ÜÜ
50 Mbps, Long GOP Ü
3
Ü
3
ÜÜ
Sensor mode Resolution and color sampling
Bit rate and
compression
1
System frequency/Frame rate
50.00 Hz 24.00 Hz
50.00P 50.00i
2
25.00P 24.00P
Full frame
Super 35mm
Super 35mm (cropped)
4096x2160
3840x2160
YCbCr 4:2:2, 10 bit
810 Mbps, Intra-frame Ü
410 Mbps, Intra-frame Ü Ü
2048x1080
1920x1080
RGB 4:4:4, 12 bit
440 Mbps, Intra-frame Ü
225 Mbps, Intra-frame Ü Ü
RGB 4:4:4, 10 bit
410 Mbps, Intra-frame Ü
210 Mbps, Intra-frame Ü Ü
Full frame
Super 35mm
Super 35mm (cropped)
Super 16mm (cropped)
2048x1080
1920x1080
YCbCr 4:2:2, 10 bit
310 Mbps, Intra-frame Ü
160 Mbps, Intra-frame Ü Ü
50 Mbps, Long GOP Ü
3
Ü
3
Ü Ü
67
Video Configuration: Video Format, Sensor Mode, System Frequency, Frame Rate, Resolution and Bit Rate
1
The camera uses a variable bit rate (VBR). Intra-frame options compress the image after analyzing each frame separately and are
more appropriate for editing. Long GOP options compress the image after analyzing also changes across a group of pictures
and offer better compression (smaller data size). qr When [Camera Setup] > [Sensor Mode] is set to
[Super 16mm (Cropped)], only [310 Mbps Intra-frame], [160 Mbps Intra-frame] and [50 Mbps Long GOP] are available.
2
Only when the resolution is set to 1920x1080.
3
qr Only when [Camera Setup] > [Sensor Mode] is set to an option other than [Full Frame].
Available video configuration settings (ProRes)
1
Selected with the [Rec/Media Setup] > [Bit Rate] setting.
2
The alpha channel is not used.
NOTES
NOTES
A single CFast card cannot be used to record XF-AVC clips using different system frequencies.
For details on the signal output from each terminal, refer to
Video Output Configuration
(A 149).
While IP streaming is activated, the video configuration (main recording format, system frequency, frame rate,
resolution/color sampling) cannot be changed.
Sensor mode Resolution, codec
1
and color sampling
System frequency/Frame rate
59.94 Hz 50.00 Hz 24.00 Hz
59.94P 29.97P 23.98P 50.00P 25.00P 24.00P
Full frame
Super 35mm
Super 35mm (cropped)
4096x2160
3840x2160
ProRes 422 HQ, 10 bit Ü Ü Ü Ü
2048x1080
1920x1080
ProRes 4444
2
, 12 bit Ü Ü Ü Ü Ü Ü
Full frame
Super 35mm
Super 35mm (cropped)
Super 16mm (cropped)
2048x1080
1920x1080
ProRes 422 HQ, 10 bit Ü Ü Ü Ü Ü Ü
Slow & Fast Motion Recording
68
Slow & Fast Motion Recording
The camera can record using a progressive frame rate (shooting frame rate) that is different from the playback
frame rate. Recording a clip at a higher frame rate than the [Frame Rate] setting will result in a slow motion effect
during playback. Conversely, a lower frame rate will result in a fast motion effect.
In most cases, sound is not recorded when slow & fast motion recording is activated. However, sound will be
recorded if the main recording format is set to [XF-AVC (CFast)] and the shooting frame rate is the same as the
frame rate in the video configuration.
For details about slow & fast motion recording when using a CDX-36150 Recorder docked with the camera,
refer to
Recording with the CDX-36150 Recorder
(A 206).
Z[]
Available shooting frame rates (XF-AVC)
1
When the shooting frame rate is higher than 30 fps, the bit rate will change to 360 Mbps if the frame rate is 23.98P or 24.00P.
2
When the shooting frame rate is 125 fps or higher, the bit rate will change to 170 Mbps if the frame rate is 59.94P or 50.00P.
3
When the shooting frame rate is 125 fps or higher, the bit rate will change to 90 Mbps for other frame rate settings.
Sensor mode Resolution
Color
sampling
Available range based on resolution/color sampling
Super 35mm
4096x2160
3840x2160
YCbCr 4:2:2
10 bit
Ü
1
2048x1080
1920x1080
RGB 4:4:4
12 or 10 bit
Ü
2048x1080
1920x1080
YCbCr 4:2:2
10 bit
Ü Ü
Super 16mm (cropped)
2048x1080
1920x1080
Ü Ü Ü
2, 3
Frame rate Shooting frame rate (fps)
59.94P 1, 2, 3, 6, 15, 30, 60 90, 120 150, 180, 210, 240
29.97P
1, 2, 3, 6, 15, 30, 32, 36, 40, 44,
48, 52, 56, 60
90, 120 150, 180, 210, 240
23.98P
24.00P
1, 2, 3, 6, 12, 24, 26, 28, 30, 32,
36, 40, 44, 48, 52, 56, 60
72, 96, 120
144, 168, 192, 216, 240
50.00P 1, 5, 15, 25, 50
54, 58, 75, 100
125, 150, 175, 200
25.00P
1, 5, 15, 25, 26, 28, 30, 34, 38,
42, 46, 50
54, 58, 75, 100
125, 150, 175, 200
69
Slow & Fast Motion Recording
qr
Available shooting frame rates (XF-AVC)
1
When the shooting frame rate is higher than 30 fps, the bit rate will change to 360 Mbps if the frame rate is 23.98P or 24.00P.
2
Only when [Camera Setup] > [Sensor Mode] is set to [Super 35mm (Cropped)].
3
When the shooting frame rate is 125 fps or higher, the bit rate will change to 170 Mbps if the frame rate is 59.94P or 50.00P.
4
When the shooting frame rate is 125 fps or higher, the bit rate will change to 90 Mbps for other frame rate settings.
Available shooting frame rates (ProRes)
1
Selected with the [Rec/Media Setup] > [Bit Rate] setting.
2
When the frame rate is a setting other than 59.94P or 50.00P.
3
qr only.
4
Z[] only.
Sensor mode Resolution
Color
sampling
Available range based on resolution/color sampling
Full frame
Super 35mm (cropped)
4096x2160
3840x2160
YCbCr 4:2:2
10 bit
Ü
1
2048x1080
1920x1080
RGB 4:4:4
12 or 10 bit
Ü
2048x1080
1920x1080
YCbCr 4:2:2
10 bit
Ü Ü
2
Super 16mm (cropped)
2048x1080
1920x1080
Ü Ü Ü
3, 4
Frame rate Shooting frame rate (fps)
59.94P 1, 2, 3, 6, 15, 30, 60 90, 120, 150
29.97P
1, 2, 3, 6, 15, 30, 32, 36, 40, 44,
48, 52, 56, 60
90, 120, 150
23.98P
24.00P
1, 2, 3, 6, 12, 24, 26, 28, 30, 32,
36, 40, 44, 48, 52, 56, 60
72
96, 120, 144, 168
50.00P 1, 5, 15, 25, 50
54, 58, 75
100, 125, 150
25.00P
1, 5, 15, 25, 26, 28, 30, 34, 38,
42, 46, 50
54, 58, 75
100, 125, 150
Sensor mode Resolution Codec
1
Available range based on resolution/codec
Full frame
Super 35mm
Super 35mm (cropped)
4096x2160
3840x2160
ProRes 422 HQ Ü
2
2048x1080
1920x1080
ProRes 4444 Ü Ü
2048x1080
1920x1080
ProRes 422 HQ Ü Ü
Super 16mm (cropped)
2048x1080
1920x1080
ProRes 422 HQ
3
ProRes 422
Ü Ü Ü
Frame rate Shooting frame rate (fps)
59.94P 1, 2, 3, 6, 15, 30, 60 90, 120, 150, 180
4
29.97P 1, 2, 3, 6, 15, 30
32, 36, 40, 44, 48,
52, 56, 60
90, 120, 150, 180
4
23.98P
24.00P
1, 2, 3, 6, 12, 24, 26, 28, 30
32, 36, 40, 44, 48,
52, 56, 60
72, 96, 120, 144, 168
50.00P 1, 5, 15, 25, 50 54, 58, 75, 100, 125, 150
25.00P 1, 5, 15, 25
26, 28, 30, 34, 38,
42, 46, 50
54, 58, 75, 100, 125, 150
Slow & Fast Motion Recording
70
Available shooting frame rates (RAW; SDI OUT output)
1 Open the slow & fast motion selection screen/submenu.
Home screen: [S&F FPS] > [ACTIVATE]
Monitoring menu: [Rec/Media Setup] (3) > [Slow & Fast Motion]
2 Select [On] and then press SET.
Z[]
When [Camera Setup] > [Sensor Mode] is set to [Super 16mm
(Cropped)], you can select a shooting frame rate up to 240 fps but the resolution is lowered to 2K
(2048x1080 or 1920x1080) and the color sampling is changed to YCbCr 4:2:2, 10 bit.
HOME screen: The current shooting frame rate appears on the control display marked with an orange
selection frame.
Monitoring menu: Close the menu. On the monitoring screen, the recording operation indicator changes to
[S&F STBY].
3 Select the desired shooting frame rate.
HOME screen: Turn the SELECT dial to select the desired frame rate and then press SET.
Monitoring menu: Set the shooting frame rate using the direct setting mode (A 73).
Available shooting frame rates will vary depending on the video configuration (frame rate, resolution, color
sampling, etc.) in use.
The selected shooting frame rate appears on the HOME screen and at the top left of the monitoring screen.
4 Press the REC button to begin recording.
The tally lamp illuminates in red and [S&F STBY] changes to [
Ü
S&F REC] while recording.
The clip is recorded at the selected frame rate.
5 Press the REC button again to stop recording.
The tally lamp will change back to green and the recording operation indication will change back to
[S&F STBY].
6 When you have finished recording, turn off the slow & fast motion recording mode.
Repeat steps 1 and 2, selecting [Off] instead.
NOTES
NOTES
The shooting frame rate cannot be changed while recording.
The time code signal will not be output from the TIME CODE IN/OUT terminal or MON. terminals.
For slower shooting frame rates, it may take a few seconds to stop recording.
If the system frequency is changed, slow & fast motion recording will be canceled and the shooting frame rate
will be reset to its default value.
Frame rate Resolution Shooting frame rate
59.94P
4096x2160
1, 2, 3, 6, 15, 30, 60
29.97P 1, 2, 3, 6, 15, 30, 32, 36, 40, 44, 48, 52, 56, 60
23.98P
24.00P
1, 2, 3, 6, 12, 24, 26, 28, 30, 32, 36, 40, 44, 48, 52, 56, 60
50.00P 1, 5, 15, 25, 50
25.00P 1, 5, 15, 25, 26, 28, 30, 34, 38, 42, 46, 50
71
Simultaneous Sub Recordings
Simultaneous Sub Recordings
You can record the same scene as the main recording also as a sub recording – a secondary recording with a
lower video configuration and smaller file sizes. For example, you can record XF-AVC clips on a CFast card or
XF-AVC Proxy clips on the SD card while the camera records or outputs RAW data, or record XF-AVC Proxy
clips on the SD card while using the CFast card for the main recording.
The video configuration of XF-AVC (Intra) sub recordings on the CFast card can be selected but that of XF-AVC
Proxy sub recordings on the SD card cannot be changed. XF-AVC Proxy clips have a video configuration of 2K
with YCbCr 4:2:0, 8-bit color sampling and a bit rate of 24 Mbps or 35 Mbps*, which makes them very
convenient for offline editing. Additionally, by specifying a LUT, you can obtain XF-AVC Proxy clips with different
color space/gamma characteristics from those of the main recording.
* Determined automatically depending on the video configuration of the main recording.
Video configuration of sub recording clips
1
The frame rate and audio recording settings will be the same as those used for the main recording.
2
Determined automatically for XF-AVC Proxy clips on the SD card. Selected with the [Rec/Media Setup] >
[Sub Rec (XF-AVC)] > [Resolution/Sampling] setting for XF-AVC clips on the CFast card.
3
Not available when the resolution of the main recording is 4512x1920.
4
qr Only when [Camera Setup] > [Sensor Mode] is set to an option other than [Full Frame].
1 Open the sub recording [Recording Media] submenu.
[Rec/Media Setup] (3) > [Sub Rec (XF-AVC)] > [Recording Media]
2 Select [CFast] (XF-AVC clips) or [SD Card] (XF-AVC Proxy clips) and then press SET.
[CFast] is only available when the main recording format is set to one of the RAW options.
Recording
media
Main recording video configuration Sub recording video configuration
1
Resolution Frame rate Resolution
2
Color sampling
Bit rate and
compression
SD card
(XF-AVC Proxy)
4512x2376 (Z)
4512x1920 (Z)
4096x2160
2048x1080
59.94P
4
, 50.00P
4
2048x1080
YCbCr 4:2:0, 8 bit
35 Mbps, Long GOP
4272x2376 (])
3840x2160
1920x1080
1920x1080
5952x3140 (qr)
5952x2532 (qr)
4512x2376 (Z)
4512x1920 (Z)
4096x2160
2048x1080
29.97P, 25.00P,
24.00P, 23.98P
2048x1080
24 Mbps, Long GOP
4272x2376 (])
3840x2160
1920x1080
1920x1080
1920x1080 59.94i
4
, 50.00i
4
1920x1080
CFast
(XF-AVC)
5952x3140 (qr)
5952x2532 (qr)
4512x2376 (Z)
4272x2376 (])
4512x1920 (Z)
4096x2160
2048x1080
59.94P
4
, 50.00P
4
4096x2160
3840x2160
3
YCbCr 4:2:2, 10 bit
810 Mbps, Intra-frame
2048x1080
1920x1080
3
310 Mbps, Intra-frame
29.97P, 25.00P,
24.00P, 23.98P
4096x2160
3840x2160
3
410 Mbps, Intra-frame
2048x1080
1920x1080
3
160 Mbps, Intra-frame
Simultaneous Sub Recordings
72
For XF-AVC sub recordings ([CFast]) only:
3 To change the resolution of the XF-AVC clips, select [Resolution/Sampling] from the same submenu.
4 Select the desired option and then press SET.
For XF-AVC Proxy sub recordings ([SD Card]) only, when using one of the Canon Log gamma curves:
3 To apply a LUT to the XF-AVC Proxy clips, open the LUT selection screen.
HOME screen: [COLOR] > [LUT] > [
8
XF-AVC]
Monitoring menu: From the same submenu select [Apply LUT].
4 Select the desired LUT and then press SET.
5 Press the REC button to start and stop recording.
The sub recording clip will be recorded on the CFast or SD card simultaneously with the main recording.
IMPORTANT
Observe the following precautions while an access indicator is illuminated in red. Failure to do so may result in
permanent data loss.
- Do not open the card slot cover of the card being accessed and do not remove the card.
- Do not remove the power source or turn off the camera.
NOTES
NOTES
If the main recording stops during simultaneous recording, the sub recording will stop as well.
Sub recording clips are not recorded during slow & fast motion recording.
During relay recording, if the camera switches from recording on one CFast card to the other (main recording),
the recording of the XF-AVC Proxy clip on the SD card (sub recording) will be interrupted as well and continue
as a separate XF-AVC Proxy clip.
When an SDHC card is used to record XF-AVC Proxy clips, the video (stream) file in an XF-AVC Proxy clip will
be split approximately every 4 GB for clips with long recording times. Still, playback on the camera will be
continuous.
Available LUT options may vary depending on the current [Gamma] and [Color Space] settings in the custom
picture file (A 134). Also, when those settings are changed, the LUT will be removed ([Apply LUT] will be
reset to [Off]).
When simultaneous sub recording is activated but no CFast card is inserted in the camera:
- If the main recording format is set to [XF-AVC (CFast)], only the sub recording (XF-AVC Proxy) clips are
recorded on the SD card.
- If the main recording format is set to [ProRes (CFast)], sub recording clips will not be recorded either.
73
Changing Main Camera Functions with the FUNC Button
Changing Main Camera Functions with the FUNC Button
With the direct setting mode you can adjust the following main functions using the optional viewfinder’s FUNC
button or an assignable button set to [FUNC] while checking the effect on the image on a monitoring device. This
section will explain the basic operation of the direct setting mode with the optional viewfinder. For details about
the functions, refer to each function’s section.
Available functions (pushing the joystick right to cycle)
Shooting frame rate for slow & fast motion recording* (A 68) Shutter speed (A 74) ISO speed/gain
(A 76) White balance (mode, color temperature value and color compensation, A 86)
* Only when slow & fast motion recording is activated.
Using the Direct Setting Mode
1 Press the FUNC button on the optional viewfinder or an assignable button set to [FUNC] (A 127).
On the monitoring screen, the icon or onscreen display of the function selected to be adjusted will be
highlighted with an orange underline.
Press the FUNC button/assignable button repeatedly or push the joystick left/right to select the function you
wish to adjust.
Alternatively, you can press an assignable button set to [Slow&Fast Frame Rate], [Shutter], [ISO/Gain] or
[White Balance] (A 127) to start the direct setting mode with the respective function already underlined.
2 Turn the SELECT dial or push the joystick up/down to select the desired value or white balance
mode and then press SET.
The selected value/mode will be set and the camera will exit the direct setting mode (the orange underline
will disappear).
You can press the BACK button instead to end the direct setting mode without changing the current value/
mode.
Shutter Speed
74
Shutter Speed
Set the shutter speed based on the recording conditions. For example, you may want to set slower shutter
speeds in darker environments. The camera offers the following modes.
You can also perform this function remotely using Browser Remote on a connected network device (A 170,
176).
[Speed]: Allows you to set the shutter speed (in fractions of a second). You can select the increment to use when
adjusting the shutter speed between 1/3-stop and 1/4-stop increments.
[Angle]: You can set the shutter angle to determine the shutter speed.
[Clear Scan]: Set the frequency in order to record CRT computer monitors without black bands or flicker on the
screen.
[Slow]: You can set slower shutter speeds to obtain brighter recordings in places with insufficient lighting. This
mode is not available during slow & fast motion recording.
[Off]: The camera uses a standard shutter speed based on the frame rate.
Available shutter speeds
The available shutter speeds vary depending on the system frequency and frame rate used.
1
When slow & fast motion recording is activated, available values will vary depending on the selected shooting frame rate.
2
Not available when slow & fast motion recording is activated.
Shutter speed mode
System frequency/Frame rate
59.94 Hz 24.00 Hz 50.00 Hz
59.94P / 59.94i 29.97P 23.98P 24.00P 50.00P/ 50.00i 25.00P
[Speed]
1
1/3-stop
increments
1/1 to 1/2000 (34 settings in total)
1/4-stop
increments
1/1 to 1/2000 (45 settings in total)
[Angle]
1
360.00°, 240.00°, 180.00°, 120.00°, 90.00°, 60.00°, 45.00°, 30.00°, 22.50°, 15.00°, 11.25°
Also angle values equivalent to the following shutter speeds: 1/120, 1/100, 1/60, 1/50, 1/40, 3/100, 1/30, 1/25.
[Clear Scan]
1
23.98 Hz to 250.38 Hz 24.00 Hz to 250.40 Hz
[Slow]
2
1/4, 1/8,
1/15, 1/30
1/4, 1/8, 1/15 1/3, 1/6, 1/12
1/3, 1/6,
1/12, 1/25
1/3, 1/6, 1/12
[Off]
1
1/60 1/30 1/24 1/50 1/25
75
Shutter Speed
Changing the Shutter Speed Mode and Value
1 Open the shutter speed [Mode] submenu.
HOME screen: [SHUTTER] > [OPTIONS] > [Mode]
Monitoring menu: [Camera Setup] (v) > [Shutter] > [Mode]
2 Select the desired mode and then press SET.
If you selected [Speed], continue the procedure to select the increment scale to use when adjusting the
shutter speed; otherwise, skip to step 5.
3 From the same submenu select [Shutter Increment].
4 Select [1/3 stop] or [1/4 stop] and then press SET.
5 HOME screen: Press the BACK button.
Monitoring menu: Press the EVF button twice to close the menu.
The current shutter speed (or angle value or clear scan frequency) appears on the control display marked
with an orange selection frame and also at the top of the monitoring screen.
6 Set the desired shutter speed.
Camera menu: Turn the SELECT dial to select the desired value and then press SET.
Monitoring menu: Set the shutter speed value using the direct setting mode (A 73).
The selected shutter speed value appears on the HOME screen and at the top of the monitoring screen.
NOTES
NOTES
Z[qr
When recording under artificial light sources such as fluorescent, mercury
or halogen lamps, the screen may flicker depending on the shutter speed. You may be able to avoid flicker by
setting the shutter speed mode to [Speed] and the shutter speed to a value matching the frequency of the
local electrical system: 1/25, 3/100, 1/50 or 1/100 for 50 Hz systems; 1/30, 1/40, 1/60 or 1/120 for 60 Hz
systems. You can also set an angle value corresponding to the shutter speeds mentioned above.
Closing down the aperture when recording under bright conditions may cause the picture to appear soft or out
of focus. To avoid the loss of sharpness due to diffraction, use a faster shutter speed, a denser ND filter
(A 78) or open up the aperture.
Z[qr
When the frame rate is set to 59.94i, 59.94P, 50.00i or 50.00P, if the
shutter speed mode is set to [Off] and slow & fast motion is not activated, you can use the [Camera
Setup] > [Flash Band Corr.] setting to have the camera detect partial flash banding on consecutive frames
and correct this to minimize the number of unusable frames. The flash band correction will be deactivated in
the following cases.
- When the frame rate, resolution/color sampling or shutter speed mode is changed.
- When slow & fast motion is activated.
- When the camera is turned off or the PLAY button is pressed (switching to playback mode).
When the shutter speed mode is set to [Slow], bright red, green or blue dots may appear on the monitoring
screen. In such case, use a faster shutter speed or select a lower ISO speed or gain value (A 76).
When using slow shutter speeds, if a very bright subject moves in the image or the brightness increases
suddenly due to a flash or other strong light, some color may appear in the brightest areas of the image.
Increasing the ISO speed/gain value may solve this.
When an optional RC-V100 Remote Controller is connected to the camera, you can change the shutter speed
mode with the remote controller’s SHUTTER SELECT button and the shutter speed value with the remote
controller’s SHUTTER
Í
/
Î
buttons.
Using Slow Shutter Mode
When recording in dark surroundings, you can obtain a brighter picture by using the slow shutter mode. You
can also use this mode when you wish to add certain effects to your recordings, such as blurring the
background during panning shots or recording a moving subject with an afterimage trail.
Image quality may not be as good as when using faster shutter speeds in brighter surroundings.
ISO Speed/Gain
76
ISO Speed/Gain
Depending on the shooting conditions, you may want to adjust the brightness of the image. You can do so by
changing the ISO speed or gain value to adjust the sensitivity of the sensor. You can also perform this function
remotely using Browser Remote on a connected network device (A 170, 176).
The minimum sensitivity needed to obtain the recommended dynamic range depends on the camera model and
other settings.
Available ISO speed and gain settings
* Sensitivity settings that are outside the recommended range but can still be used by setting [ISO/GAIN] > [OPTIONS] >
[Extended Range] to [On].
**Available only when the extended range is not activated.
Camera model
[Gamma] setting in the custom picture file (A 134)
[Canon Log] or [Wide DR] [Canon Log 2] or [Canon Log 3]
Z[qr
ISO 400 / 6 dB ISO 800 / 12 dB
]
ISO 1600 / 6 dB ISO 3200 / 12 dB
Z[
q
r
ISO/Gain increment Normal range Extended range*
ISO speed
[1 stop]
(1-stop increments)
160**, 200, 400, 800, 1600, 3200, 6400, 12800, 25600 100, 51200, 102400
[1/3 stop]
(1/3-stop increments)
160, 200, 250, 320, 400, 500, 640, 800, 1000, 1250, 1600,
2000, 2500, 3200, 4000, 5000, 6400, 8000, 10000, 12800,
16000, 20000, 25600
100, 125, 32000, 40000, 51200,
64000, 80000, 102400
Gain
[Normal]
(3-dB increments)
–2 dB**, 0 dB to 42 dB –6 dB, –3 dB, 45 dB to 54 dB
[Fine]
(0.5-dB increments)
–2 dB to 42 dB 42.5 dB to 54 dB
]
ISO/Gain increment Normal range Extended range*
ISO speed
[1 stop]
(1-stop increments)
640**, 800, 1600, 3200, 6400, 12800, 25600 400, 51200, 102400
[1/3 stop]
(1/3-stop increments)
640, 800, 1000, 1250, 1600, 2000, 2500, 3200, 4000, 5000,
6400, 8000, 10000, 12800, 16000, 20000, 25600
400, 500, 32000, 40000, 51200,
64000, 80000, 102400
Gain
[Normal]
(3-dB increments)
–2 dB**, 0 dB to 30 dB –6 dB, –3 dB, 33 dB to 42 dB
[Fine]
(0.5-dB increments)
–2 dB to 30 dB 30.5 dB to 42 dB
77
ISO Speed/Gain
Changing the ISO Speed or Gain Value
1 Open the ISO speed/gain [Select] submenu.
HOME screen: [ISO/GAIN] > [OPTIONS] > [Select]
Monitoring menu: [Camera Setup] (v) > [ISO/Gain] > [Select]
2 Select [ISO] or [Gain] and then press SET.
3 From the same submenu, select [ISO Increment] or [Gain Increment] to select the adjustment
increment to use when adjusting the ISO speed or gain, respectively.
4 Select the desired option and then press SET.
5 HOME screen: Press the BACK button.
Monitoring menu: Press the EVF button twice to close the menu.
The current ISO speed/gain value appears on the control display marked with an orange selection frame
and also at the top of the monitoring screen.
6 Set the desired ISO speed/gain value.
HOME screen: Turn the SELECT dial to select the desired value and then press SET.
Monitoring menu: Set the ISO speed/gain value using the direct setting mode (A 73).
The selected ISO speed/gain value appears on the HOME screen and monitoring screen.
Using the Control Dial
You can adjust the ISO speed or gain value using the control dial
on the left side of the camera. The function of the control dial is
determined by the position of the CUSTOM switch next to it. You
can set in advance the functions that are assigned to each
position of the CUSTOM switch.
1 Open the [CUSTOM Switch] submenu.
[System Setup] (B) > [CUSTOM Switch]
2 Select [1] or [2] depending on the switch position to which
you want to assign the ISO speed/gain function and then
press SET.
[1] is the top position (initially assigned to the aperture
function); [2] is the bottom position (initially unassigned).
3 Select [ISO/Gain] and then press SET.
4 Close the menu and set the CUSTOM switch to the
position set to [ISO/Gain].
5 Turn the control dial to change the ISO speed/gain value.
NOTES
NOTES
When high ISO speeds or gain levels are set, the image on the monitoring screen may flicker slightly.
When high ISO speeds or gain levels are set, bright red, green or blue dots may appear on the monitoring
screen. In such case, use a faster shutter speed (A 74) or select a lower ISO speed or gain value.
When the ISO speed or gain level is changed, some noise may appear momentarily on the monitoring screen.
Do not adjust the ISO speed/gain level while recording.
You can use the [System Setup] > [Control Dial Dir.] > [Camera] setting to change the direction of
the adjustment when you turn the control dial.
When an optional RC-V100 Remote Controller is connected to the camera, you can adjust the ISO speed or
gain value with the remote controller’s ISO/GAIN
Í
/
Î
buttons.
Control dial
CUSTOM Switch
ND Filter
78
ND Filter
Using the ND filter allows you to open up the aperture to obtain a shallower depth of field even when recording in
bright surroundings. You can also use the ND filter to avoid the soft focus caused by diffraction when using small
apertures. By default, you can select one of 3 density levels (2 to 6 stops) and, if you enable the extended ND
range, you can select one of 5 density levels (2 to 10 stops).
You can also perform this function remotely using Browser Remote on a connected network device (A 170,
176).
Press the ND FILTER + or button to select the desired ND filter setting.
Alternatively, using the HOME screen: [IRIS] > [ND +] and [ND –]. Or, you can press an assignable
button set to [ND +] or [ND –] (A 127).
Repeatedly pressing the ND FILTER + button will change the ND filter setting in the following order:
[2 stops] [4 stops] [6 stops] [8 stops]* [10 stops]* ND filter off.
(The ND FILTER
button cycles through the settings in reverse order.)
The selected ND filter setting appears on the HOME screen and at the top of the monitoring screen.
* Only when [IRIS] > [OPTIONS] > [Extended ND Range] is set to [On].
NOTES
NOTES
Depending on the scene, the color may change when turning the ND filter on/off. Setting a custom white
balance (A 87) may be effective in such case.
About the extended ND range: When you switch to or from a density level in the extended range (8 or 10 stops),
you may notice one or both of the following circumstances.
- The focus may shift, affecting also the indication on the lens’s focus distance scale.
- Depending on the lens, the camera may not be able to focus at infinity focus.
You can use the [System Setup] > [ND FILTER Button] setting to deactivate the ND FILTER
buttons.
About changing the ND filter setting using the optional RC-V100 Remote Controller:
- When the remote controller is connected to the camera, you can use the remote controller’s ND button in
the same way as the camera’s ND FILTER + button.
- For settings between 2 and 8 stops, the corresponding ND filter indicator (1 to 4, respectively) will illuminate
in orange. When the ND filter is set to 10 stops, indicators 1 and 4 will both illuminate.
79
Adjusting the Aperture
Adjusting the Aperture
You can affect the brightness of your recordings or change the depth of field by adjusting the aperture. By
default, the camera is set to manual aperture but, depending on the lens used, the camera offers 3 ways to
adjust the aperture. For a list of compatible lenses and functions that can be used, refer to the appendix
(A 240).
Available aperture values will vary depending on the lens attached. You can select the adjustment increment and
even use the smallest iris increment allowed by the lens.
When the optional SG-1 Shoulder Style Grip Unit is attached to the camera, you can also adjust the aperture
using the grip.
[]r
only: When a PL lens is attached to the camera, if you connect
the 12-pin camera interface cable to the camera, you can adjust the aperture from the camera.
Manual aperture: Adjust the aperture value manually using the control dial on the camera, the camera menu, or
remotely, using Browser Remote on a connected network device (A 170, 176).
Push auto iris: Momentary automatic aperture. During manual aperture, press an assignable button or use
Browser Remote (A 170, 176) to temporarily adjust the aperture automatically.
Automatic aperture: The camera adjusts the aperture automatically.
Required settings on EF Cinema lenses and broadcast lenses
To adjust the aperture from the camera, you will need to enable automatic adjustment using the controls on the
lens. Required settings vary depending on the lens. Refer to the following table and the instruction manual of the
lens used.
NOTES
NOTES
When the optional SG-1 Shoulder Style Grip Unit is attached to the camera: To adjust the aperture from the camera,
set the SG-1’s IRIS (aperture control) switch to the A position. For details refer to the SG-1’s instruction
manual.
Lens Part used on the lens Setting for automatic adjustment
CN7x17 KAS S/E1, CN7x17 KAS S/P1,
CN20x50 IAS H/E1, CN20x50 IAS H/P1,
compatible broadcast lenses (A 240)
Iris operation change-over switch A
CN-E18-80mm T4.4 L IS KAS S,
CN-E70-200mm T4.4 L IS KAS S
Iris auto/manual change-over switch A
Adjusting the Aperture
80
Manual Aperture
With the control dial on the left side of the camera you can adjust the aperture value of a compatible lens using
the smallest iris increment allowed by the lens. The function of the control dial is determined by the position of
the CUSTOM switch next to it. By default, the top position is assigned to iris control but you can set in advance
the functions that are assigned to each position of the CUSTOM switch.
1 Open the aperture [Mode] submenu.
HOME screen: [IRIS] > [OPTIONS] > [Mode]
Monitoring menu: [Camera Setup] (v) > [Iris] > [Mode]
Alternatively, you can press an assignable button set to [Iris
Mode] (A 127).
This setting is available only when an EF lens compatible with
automatic aperture is attached to the camera. For non-
compatible lenses, the aperture mode will be set to [Manual]
and cannot be changed. Skip to step 3.
2 Select [Manual] and then press SET.
When using a compatible EF Cinema/broadcast lens, enable
automatic adjustment on the lens (A 79).
3 From the same submenu select [Iris Increment].
4 Select [1/2 stop] or [1/3 stop] and then press SET.
You can further select [Fine Increment] from the same submenu and set it to [On] to use the smallest iris
increment allowed by the lens attached. Nevertheless, the aperture value displayed on the HOME screen
and monitoring screen will be the closest value in the selected increment scale.
To use the HOME screen:
5 Press the BACK button once or press [IRIS].
The current aperture value appears on the control display marked with an orange selection frame.
6 Turn the SELECT dial to select the desired value and then press SET.
Alternatively, you can press an assignable button set to [Iris +] or [Iris –] (A 127).
The selected aperture value appears on the HOME screen and at the top of the monitoring screen.
To use the control dial:
5 Close the menu and set the CUSTOM switch to the top position “1 (IRIS)”.
The iris function is assigned to position 1 by default. If it has been changed, assign [Iris] to one of the
CUSTOM switch’s positions (steps 1 to 3 selecting [Iris] instead of [ISO/Gain], A 77) and set the CUSTOM
switch to the position set to [Iris].
6 Turn the control dial to change the aperture value.
The selected aperture value appears on the HOME screen and at the top of the monitoring screen.
NOTES
NOTES
You can use the [System Setup] > [Control Dial Dir.] > [Camera] setting to change the direction of
the adjustment when you turn the control dial.
When using an EF lens with no lens contacts or most EF Cinema lenses*, you cannot adjust the aperture using
the camera. Adjust the aperture using the lens.
* Select EF Cinema lenses and broadcast lenses (A 240) support iris adjustment from this camera.
When using an EF lens that can correct the aperture value according to the position of the zoom, you can use
the [IRIS] > [OPTIONS] > [Zoom-Iris Correct.] setting to activate this correction.
When an optional RC-V100 Remote Controller is connected to the camera, you can adjust the aperture with
the remote controller’s IRIS dial. At default settings, turn the dial right to open up the aperture and left to close
the aperture.
Control dial
CUSTOM Switch
81
Adjusting the Aperture
When using a compatible EF Cinema lens, you can change the displays to T values instead of F values with
the [IRIS] > [OPTIONS] > [Iris Indicator] setting.
The aperture value (F value or T value) displayed on the screen may differ from the indication on the lens’s
aperture scale.
When using an EF Cinema lens or broadcast lens compatible with iris adjustment from the camera, when the
iris is almost fully closed, the aperture value displayed on the monitoring screen may appear in gray.
When using an EF Cinema lens or broadcast lens compatible with iris adjustment from the camera, when you
change the aperture value from a position of fully open or fully closed iris, multiple adjustment operations may
be required until the aperture changes.
Momentary Automatic Aperture - Push Auto Iris
During manual aperture, you can press the PUSH AUTO IRIS button to have the camera temporarily take control
and automatically adjust the aperture for an optimal exposure.
You can also perform this function remotely using Browser Remote on a connected network device (A 170,
176).
1 Set the iris mode to [Manual] (steps 1-2, A 80).
When using a compatible EF Cinema/broadcast lens, enable automatic adjustment on the lens (A 79).
2 Press and hold the PUSH AUTO IRIS button.
Alternatively, using the HOME screen: [IRIS] > [AUTO IRIS].
The camera will automatically adjust the aperture to obtain optimal exposure. As long as you hold the button
pressed down,
E
will appear on the monitoring screen next to the aperture value.
When you release the button, automatic aperture mode will end and the
E
icon will disappear. The selected
aperture value will appear on the HOME screen and at the top of the monitoring screen.
NOTES
NOTES
You can use the [IRIS] > [OPTIONS] > [AE Response] setting to change how quickly the aperture
changes during automatic aperture mode.
Push auto iris is not available when slow & fast motion recording is activated.
Automatic Aperture
When a compatible EF lens is attached to the camera, you can have the camera automatically adjust the
aperture.
1 Open the aperture [Mode] submenu.
HOME screen: [IRIS] > [OPTIONS] > [Mode]
Monitoring menu: [Camera Setup] (
v
) > [Iris] > [Mode]
Alternatively, you can press an assignable button set to [Iris Mode] (A 127).
2 Select [Automatic] and then press SET.
When using a compatible EF Cinema/broadcast lens, enable automatic adjustment on the lens (A 79).
The camera will automatically adjust the aperture to obtain optimal exposure.
The selected aperture value will appear on the HOME screen and at the top of the monitoring screen with an
E
icon next to it.
Adjusting the Aperture
82
NOTES
NOTES
Automatic aperture is not available when slow & fast motion recording is activated.
qr
When [Camera Setup] > [Sensor Mode] is set to [Full Frame] and an EF-S lens
or Super 35mm lens is attached to the camera, the camera will not achieve optimal exposure.
The aperture value may change in the following cases.
- While using the built-in extender or iris compensation function of an EF Cinema lens, when you switch from
automatic aperture to manual aperture.
- When the aperture’s onscreen display is changed between T values/F values.
- When the aperture controls on the lens are switched between automatic/manual mode.
When using EF lenses/broadcast lenses that let you adjust the aperture gain, if the aperture gain is set too
high, the aperture adjustment may not be stable (aperture hunting), depending on the shooting conditions. In
such case, reset the lens’s aperture gain to its initial value.
Exposure Compensation - AE Shift
Use AE shift to compensate the exposure that was set using automatic aperture, in order to darken or lighten the
image.
You can also perform this function remotely using Browser Remote on a connected network device (A 170,
176).
1 Open the [AE Shift] submenu.
HOME screen: [IRIS] > [OPTIONS] > [AE Shift]
Monitoring menu: [Camera Setup] (
v
) > [AE] > [AE Shift]
2 Select an AE shift level and then press SET.
Alternatively, you can press an assignable button set to [AE Shift +] or [AE Shift –] (A 127).
You can select one of 17 AE shift levels from –2.0 to +2.0.
The selected AE shift level will be displayed on the monitoring screen, next to the exposure bar, and the
camera will attempt to adjust the exposure accordingly.
Light Metering Mode
Select the light metering mode to match the recording conditions. Using the appropriate setting will ensure that
the camera obtains the most suitable exposure level when automatic aperture is used.
1 Open the [Light Metering] submenu.
[Camera Setup] (
v
) > [Light Metering]
2 Select the desired option and then press SET.
Alternatively, you can press an assignable button set to [Backlight] or [Spotlight] (A 127).
The icon of the selected mode ( or , no icon for [Standard]) appears at the left of the monitoring
screen.
The Exposure Bar
The
Î
on top of the exposure bar indicates optimal exposure without any shift
(AE±0); the scale markings indicate the deviation from optimal exposure in
1/2 EV increments. The indicator inside the exposure bar represents the current
exposure. When the difference between current and optimal exposure is larger
than ±2 EV, the indicator will flash at the edge of the exposure bar. Optimal
exposure will change depending on the light metering mode used.
Optimal exposure AE±0
Current exposure
83
Adjusting the Aperture
Options
[Backlight]: Suitable when recording backlit scenes.
[Standard]: Averages the light metered from the entire screen, giving more weight to the subject in the
center.
[Spotlight]: Use this option when recording a scene in which only a certain part of the picture is lit, for
example, when the subject is lit by a spotlight.
Gamma Curve and Main Color Settings
84
Gamma Curve and Main Color Settings
The basic color management with this camera is determined by the main settings of the custom picture file:
gamma curve, color space and color matrix. You can select one of the preset color settings offered by the
camera or set each setting individually. For details about the custom picture file and settings, refer to
Custom
Picture Settings
(A 131).
When the main recording format is set to RAW, a special gamma curve optimized for RAW video is used,
regardless of these settings.
Preset Color Settings
The camera offers the following preset color settings (combinations of gamma curve, color space and color
matrix). You can also set each of the main settings individually or edit the custom picture file (A 131) to adjust
to your preference every detailed aspect of the custom picture settings (A 134).
* [COLOR] > [CP MAIN] > [Preset], [Gamma], etc.
NOTES
NOTES
About the logarithmic gamma curves (Canon Log settings)
These gamma curves assume the need for post-production processing. They were designed to make the
most of the imaging sensor characteristics in order to obtain impressive levels of dynamic range.
- You can apply a LUT to video output from the camera’s various terminals (A 155) to use gamma curve/
color space settings more suitable for viewing on the optional viewfinder or an external monitor screen.
- There are also other LUTs available that can be applied for processing in post-production. For the latest
information on available LUTs, please visit your local Canon Web site.
[Preset]* [Gamma]* [Color Space]* [Color Matrix]* Characteristics
[Canon Log 3 :
C.Gamut]
[Canon Log 3]
[Cinema Gamut]
[Neutral]
These settings use Canon Log 3 gamma and presume a
workflow that includes post-production processing.
This gamma curve keeps the characteristics of the [Canon
Log] setting while expanding its dynamic range. The color
space can be selected from 4 options.
[Canon Log 3 :
BT.2020]
[BT.2020 Gamut]
[Canon Log 3 :
DCI-P3]
[DCI-P3 Gamut]
[Canon Log 3 :
BT.709]
[BT.709 Gamut]
[Canon Log 2 :
C.Gamut]
[Canon Log 2]
[Cinema Gamut]
[Neutral]
These settings use Canon Log 2 gamma and presume a
workflow that includes post-production processing.
They achieve an even wider dynamic range than with the
[Canon Log] setting and superior gradation in the shadows
(dark areas of the image). The color space can be selected
from 4 options.
[Canon Log 2 :
BT.2020]
[BT.2020 Gamut]
[Canon Log 2 :
DCI-P3]
[DCI-P3 Gamut]
[Canon Log 2 :
BT.709]
[BT.709 Gamut]
[Canon Log] [Canon Log] [BT.709 Gamut]
[Cinema EOS
Original]
This setting uses Canon Log gamma and presumes a
workflow that includes post-production processing.
It can obtain an impressive dynamic range and color tones
appropriate for post-production.
[BT.2020]
[Wide DR]
[BT.2020 Gamut]
[Neutral]
These settings produce the widest dynamic range possible
without requiring post-production. The color space can be
selected from 2 options.
[BT.709] [BT.709 Gamut]
85
Gamma Curve and Main Color Settings
1 Open the custom picture file’s selection screen.
HOME screen: [COLOR] > [CP OTHERS] > [File] > [Select]
Monitoring menu: [Custom Picture] (
/
) > [File] > [Select]
2 Turn the SELECT dial to select the desired file and then press [OK] (HOME screen) or press SET
(monitoring menu).
Select one of the custom picture files saved in the camera (C1 to C20). To use the settings of a custom
picture file saved on an SD card, copy the file to the camera in advance (A 133).
3 Open the [Preset] submenu.
HOME screen: [COLOR] > [CP MAIN] > [Preset]
Monitoring menu: Press the BACK button to return to the [Custom Picture] submenu and then select [Preset].
4 Select the desired setting and then press SET.
To select the gamma curve, color space or color matrix individually, select [Off] and continue the procedure
with step 5. To use one of the preset settings as is, the rest of the procedure is not necessary.
5 Open the [Gamma] submenu.
HOME screen: From the same submenu select [Gamma].
Monitoring menu: From the same submenu select [Main Settings] and then select [Gamma].
6 Select the desired gamma curve (A 134) and then press SET.
Repeat steps 5 and 6, selecting [Color Space] to select the color space, and/or [Color Matrix] to select the
color matrix in the same way.
White Balance
86
White Balance
The camera uses an electronic white balance process to calibrate the picture and produce accurate colors under
different lighting conditions. There are 4 methods of setting the white balance.
You can also perform this function remotely using Browser Remote on a connected network device (A 170,
175).
Auto white balance (AWB): The camera automatically adjusts the white balance to the optimal level.
Custom white balance: You can use a gray card or white object with no pattern to calibrate the white balance
and set it to one of two custom white balance positions,
Å
A or
Å
B. You can further adjust the color
temperature value (K) and the color compensation (CC*) value.
Preset white balance: Set the white balance to
¼
(daylight) or
É
(tungsten lamp). You can further adjust the
color temperature value (K) and the color compensation (CC*) value.
User-set color temperature: The camera offers 5 white balance settings ( to ), each of which you can set
independently to a color temperature between 2,000 K and 15,000 K and further adjust the color compensation
(CC*) value.
* The CC value adjusts the balance of the image along the green/magenta gradation.
NOTES
NOTES
The [Color Matrix Tuning] and [White Balance] settings in the custom picture file (A 137) take precedence
over the white balance set with these procedures.
You can use the [WB] > [OPTIONS] > [Shockless WB] setting to make the transition look
smoother when you change the white balance settings.
You can use the [WB] > [OPTIONS] > [C. Temp. Increment] setting to set the units for the color
temperature to [Mired] (in 5-mired increments) or [Kelvin] (in 100-kelvin increments). Even with the [Mired]
option, the color temperature is converted to and displayed in kelvins. Note that changing the aforementioned
setting may alter the white balance.
When an optional RC-V100 Remote Controller is connected to the camera, you can adjust the white balance
with the remote controller’s AWB button, A button, B button, PRESET button and
Å
button.
The color temperatures displayed on the control display and monitoring screen are approximate. Use them
only as a reference.
Selecting the White Balance Mode/Setting
1 Open the [White Balance] screen.
HOME screen: [WB]
You can also select the white balance mode/setting using the direct setting mode (A 73).
2 Turn the SELECT dial to select the desired white balance setting.
The color temperature and CC value for the highlighted setting are displayed on the right side of the control
display and at the top of the monitoring screen.
Alternatively, you can press an assignable button set to [ AWB], [
Å
Set A], [
Å
Set B], [
¼
Daylight],
[
É
Tungsten] or one of the settings [ USER_01] to [ USER_05] (A 127).
To register a custom white balance, adjust the color temperature/CC value or rename a user setting,
continue with the following procedures.
87
White Balance
Auto White Balance (AWB)
The camera constantly adjusts the white balance automatically to achieve an optimal level. The camera will
adjust the white balance if the light source changes.
1 Select the [ AWB] setting and press SET (A 86).
The icon and the current color temperature and CC value set automatically by the camera will appear
on the HOME screen and at the top of the monitoring screen.
NOTES
NOTES
Custom white balance may provide better results in the following cases:
- Changing lighting conditions
-Close-ups
- Subjects in a single color (sky, sea or forest)
- Under mercury lamps and certain types of fluorescent and LED lights
You can use the [WB] > [OPTIONS] > [AWB Response] setting to change how quickly the white
balance changes in auto white balance (AWB) mode.
If you set an assignable button to [AWB Lock] (A 127), you can press the button to lock the current white
balance settings set automatically by the camera. To cancel the lock, press the button again (resume auto
white balance mode) or select a different white balance setting.
Registering a Custom White Balance
1 Select the [
Å
Set A] or [
Å
Set B] setting (A 86).
To apply the stored color temperature and CC value without changes, press SET. The rest of the procedure
is not necessary.
2 HOME screen only: Press [WB SET].
3 Point the camera at a gray card or white object so that it fills the center of the monitoring screen.
Use the same lighting conditions you plan to use when recording.
4 Press [OK] (HOME screen) or press an assignable button set to [Set White Balance] (A 127)
(monitoring screen/direct setting mode).
•The
Å
icon will flash on the control display. The
Å
A or
Å
B icon will flash quickly at the top of the
monitoring screen.
Make sure the gray card or white object fills the center of the monitoring screen until the procedure is
completed.
When the procedure is completed, the [White Balance] screen will appear on the control display and the
icon will stop flashing on the monitoring screen. The color temperature and CC value registered by the
camera will appear on the HOME screen and at the top of the monitoring screen, next to the
Å
A or
Å
B
icon. These settings are saved even if you turn off the camera.
If necessary, adjust the color temperature or CC value (A 88).
NOTES
NOTES
Readjust the custom white balance if the light source changes.
Very rarely and depending on the light source, the icon will not stop flashing. Even so, the white balance is
correctly calibrated and you can continue shooting.
After the camera registers a custom white balance the color temperature or CC value may appear in gray. This
indicates that the value registered exceeds the range of values that can be displayed but the white balance is
correctly calibrated and you can continue shooting.
White Balance
88
Adjusting the Color Temperature or CC Value
1 Select a white balance setting other than [ AWB] (A 86).
2 Press [ADJUST].
The current color temperature value and CC value appear on the control display. The color temperature will
be marked with an orange selection frame.
You can also change the color temperature and CC value using the direct setting mode (A 73).
3 Turn the SELECT dial to select the desired value and then press SET.
Press [ ] or [ ] to skip 10 values backwards/forwards.
Press SET or [< >] to move the selection frame between the color temperature and CC value and repeat this
step to adjust the other value.
Press [RESET] to reset the color temperature and CC value to their default settings.
4 After adjusting the white balance settings as necessary press [OK].
The selected color temperature and CC value will appear on the HOME screen and at the top of the
monitoring screen, next to the white balance icon.
Adjustment ranges
NOTES
NOTES
If after registering a custom white balance, the color temperature and CC value appear in gray, you will not be
able to adjust the color temperature or CC value.
Renaming User-Set White Balance Settings
1 Select [ USER_01] to [ USER_05] (A 86).
2 Press [RENAME].
Enter the desired name (up to 8 characters) using the virtual keyboard (A 37).
White balance mode/setting
Adjustment range
Color temperature (K) Color compensation (CC) value
[
¼
Daylight] 4,300 K to 8,000 K
–5 to +5
[
É
Tungsten] 2,700 K to 3,700 K
[
Å
Set A], [
Å
Set B],
[ USER_01] to [ USER_05]
2,000 K to 15,000 K –20 to +20
89
Adjusting the Focus
Adjusting the Focus
Depending on the lens used, the camera offers several ways to focus and incorporates Dual Pixel CMOS AF
technology for advanced autofocus performance. For a list of compatible lenses and functions that can be used,
refer to the appendix (A 240). You can also adjust the focus remotely using Browser Remote on a connected
network device (A 170, 177).
Manual focus: Turn the focus ring on the lens to adjust the focus. The camera offers several focus assistance
functions (A 90) to help you focus more accurately when using the manual focus.
One-shot AF*: With the lens’s focus mode switch set to AF, you will be able to focus manually but still have the
option to press the ONE-SHOT AF button to let the camera focus automatically once on the subject inside the
AF frame.
AF-Boosted MF*: Focus manually most of the way and let the camera finish focusing automatically.
Continuous AF*: The camera continuously focuses on the subject inside the AF frame. You can use the AF lock
function (A 95) to change the composition of the picture while keeping the focus on the selected spot.
Face AF*: The camera automatically detects a person’s face, focuses on it and can track it if that person moves.
Tracking*: After you select a subject, the camera keeps focusing it and tracks the subject if it moves.
*
Zq
only. Not available when a manual focus lens is attached to the camera.
Focusing methods and required settings
1
For the necessary settings on compatible EF Cinema lenses and broadcast lenses, see the table below.
2
[AF] > [OPTIONS] > [AF Mode] setting.
3
Depending on the lens, the focus ring may be disabled when the focus mode switch is set to AF.
4
You can activate this mode with the [AF] > [FACE] setting.
5
You can activate this mode with the [AF] > [TRACKING] setting.
Required settings on EF Cinema lenses and broadcast lenses
To adjust the focus from the camera, you will need to change the focus mode using the controls on the lens.
Required settings vary depending on the lens. Refer to the following table and the instruction manual of the lens
used.
Focusing method
Focus mode switch
on an EF lens
1
AF mode
2
Manual focus
Focus ring
MF
AF
3
[One Shot]
Browser Remote AF
One-shot AF
ONE-SHOT AF button
AF [One Shot]
Browser Remote
AF-Boosted MF
Focus ring
Camera (automatic)
AF [AF-Boosted MF]
Browser Remote
Camera (automatic)
Continuous AF
Automatic
(camera or Browser Remote)
AF [Continuous]
Face AF
4
/Tracking
5
Camera or Browser Remote AF
Lens Part used on the lens
Setting for automatic
adjustment
Setting for manual
adjustment
CN7x17 KAS S/E1, CN7x17 KAS S/P1,
CN20x50 IAS H/E1, CN20x50 IAS H/P1,
compatible broadcast lenses (A 240)
Focus operation
change-over knob
SERVO MANU.
CN-E18-80mm T4.4 L IS KAS S,
CN-E70-200mm T4.4 L IS KAS S
Autofocus/Manual Focus
change-over switch
AF MF
Adjusting the Focus
90
Manual Focus
Focus manually using the focus ring on the lens. You can also perform this function remotely using Browser
Remote on a connected network device (A 170, 177).
The autofocus mode is set to [One Shot] by default. If you need to change the setting, start the procedure from
the beginning. Otherwise, you can start from step 3 below.
1 Open the focus [AF Mode] submenu.
Setup screen: [AF] > [OPTIONS] > [AF Mode]
Monitoring menu: [Camera Setup] (
v
) > [Focus] > [AF Mode]
2 Select [One Shot] and then press SET.
On an EF lens, you can set the lens’s focus mode switch to MF. On a compatible EF Cinema/broadcast lens,
you can enable manual adjustment on the lens (A 89).
3 Turn the focus ring to adjust the focus.
Alternatively, open the [AF] screen ( > [AF]) and turn the SELECT dial to adjust the focus.
NOTES
NOTES
With some EF lenses, you may be able to operate the focus ring even when the focus mode switch is set to
AF.
If you operate the zoom after focusing, the focus on the subject may be lost.
If you focus manually and then leave the camera with the power turned on, the focus on the subject may be
lost after a while. This possible slight shift in focus is a result of the internal temperature rising in the camera
and lens. Check the focus before resuming shooting.
When adjusting the focus, be careful not to touch the front of the lens or moving parts on the lens except for
the focus ring.
When an optional RC-V100 Remote Controller is connected to the camera, you can adjust the focus with the
remote controller’s FOCUS dial. At default settings, turn the dial right to focus farther and left to focus nearer.
To be able to adjust the focus using an accessory connected to a lens (itself connected to the camera using
the 12-pin interface cable), you will need to change the [Camera Setup] > [Focus Control] setting to
give priority to the lens.
Using the Focus Assistance Functions
In order to focus more accurately, you can use the following focus assistance functions: Dual Pixel Focus Guide
(
Zq
only), an onscreen guide that shows you if the picture is in focus; peaking, which creates a
clearer contrast by emphasizing the outlines of the subject; and magnification, which enlarges the image on the
screen. You can use peaking and the focus guide or peaking and magnification simultaneously for greater effect.
Zq
Dual Pixel Focus Guide
The focus guide gives you an intuitive visual indication of the current focus distance and the direction and
amount of adjustment necessary to bring the picture into full focus. When used in combination with face
detection (A 96), the guide will focus on the vicinity of the eyes of the person detected as the main subject.
1 Activate the focus guide.
Setup screen: [F. ASSIST.] > [GUIDE] (set it to [On])
Monitoring menu: [Assist. Functions] (
A
) > [Focus Guide] > [Activate] > [On]
Alternatively, you can press an assignable button set to [Focus Guide] (A 127).
2 If necessary, move the focus guide frame.
Setup screen: Press [ FRAME] and then press [
Í
], [
Î
], [
Ï
], [
Ð
].
Monitoring menu: Use the joystick or SELECT dial on the optional viewfinder.
The frame cannot be moved when tracking is activated or a face detection frame is displayed.
91
Adjusting the Focus
Press [CENTER] (setup screen) or press the BACK button on the optional viewfinder to return the frame to
the center position.
3 You can also display a second frame around a different subject.
Setup screen: From the [Focus Assistance Functions] screen in step 1, [OPTIONS] > [Focus Guide] >
[Display 2nd Frame] > [On]
Monitoring menu: From the same submenu, [Display 2nd Frame] > [On]
When the following screens are displayed on the control display, you can press SET to switch the focus
guide display from one frame to the other.
- The [AF] screen ( [AF]) and its [Move frame] screen ( [AF] > [ FRAME])
- The [Focus Assistance Functions] screen ( [F. ASSIST.]) and its [Move frame] screen (
[F. ASSIST.] > [ FRAME])
NOTES
NOTES
With subjects or in situations where autofocus may not work well (A 94), the focus guide may not work
correctly.
The focus guide cannot be used in the following cases:
- While the focus is being adjusted automatically using one-shot AF or continuous AF.
- When the aperture value used is F11 or larger.
- When a manual focus lens is attached to the camera, except for compatible EF Cinema lenses (A 240).
When the focus guide and face detection functions are used together, the focus guide may not focus the main
subject’s eyes correctly, depending on the direction in which the face is turned.
Peaking
The camera offers two peaking levels.
1 Press the PEAKING button.
Alternatively, you can press [F. ASSIST.] > [PEAKING] to turn peaking on and off. From the
monitoring menu you can use the [Assist. Functions] (
A
) > [Peaking] > [VIDEO Output] and
[MON.+HDMI Output] settings to turn the peaking on and off separately on the optional viewfinder or on
external monitors.
On monitors connected to one of the MON. terminals or the HDMI OUT terminal, the peaking icon (
J
or
K
) appears at the right of the monitoring screen and the outlines in the image will be emphasized,
depending on the focus.
Press the button again to turn off peaking.
2 Open the peaking’s [Select] submenu to select the peaking level.
Setup screen: [F. ASSIST.] > [OPTIONS] > [Peaking] > [Select]
Monitoring menu: [Assist. Functions] (
A
) > [Peaking] > [Select]
3 Select the desired level and then press SET.
In focusFocus farther
(large adjustment)
Focus farther
(small adjustment)
Focus closer
(small adjustment)
Focus closer
(large adjustment)
Cannot determine
adjustment
Adjusting the Focus
92
Magnification
You can select from two levels of magnification, which depend on the sensor mode.
1 Press the MAGN. button.
Alternatively, you can press [F. ASSIST.] > [MAGN.] to turn the magnification on and off. From the
monitoring menu you can use the [Assist. Functions] (
A
) > [Magnification] > [VIDEO Output] and
[MON.+HDMI Output] settings to turn the magnification on and off separately on the optional viewfinder or
on external monitors.
On monitors connected to one of the MON. terminals or the HDMI OUT terminal, the
^
appears at the
top right of the monitoring screen and the center of the screen* is magnified approximately 2x
(
qr
3x, when the sensor mode is set to [Full Frame]).
The orange frame displayed on the top right of the screen (magnification frame) shows the approximate part
of the image shown magnified.
2 If necessary, move the magnification frame to check other parts of the image.
Setup screen: [F. ASSIST.] > [ FRAME] and then press [
Í
], [
Î
], [
Ï
], [
Ð
].
Monitoring menu: Use the joystick or SELECT dial on the optional viewfinder.
Press [CENTER] (setup screen) or press the BACK button on the optional viewfinder to return the
magnification frame to the center position.
3 Press SET (setup screen) or the joystick (monitoring menu) to change the magnification level.
Press repeatedly to switch back and forth between approx. 2x and 4x magnification (
qr
approx. 3x or 6x, when the sensor mode is set to [Full Frame]).
4 Press the MAGN. button again to cancel the magnification.
* If one of the AF frames or a face detection frame is displayed on the screen, the area around the active frame will be magnified
instead.
NOTES
NOTES
About Peaking/Magnification:
- You can use the [F. ASSIST.] > [OPTIONS] > [Peaking] > [Peaking 1] and [Peaking 2] settings to
set the color, gain and frequency of the two peaking levels independently of each other.
- You can select individually through which terminals to output (on which monitoring devices to display) the
assistance functions with the output settings under [F. ASSIST.] > [OPTIONS] > [Peaking] and
[Magnification]. When the HDMI OUT terminal’s resolution is set to 4096x2160 or 3840x2160, the
assistance functions will not be displayed on the monitor connected to the HDMI OUT terminal.
- You can also use the [Focus Assist. B&W] setting under [F. ASSIST.] > [OPTIONS] > [Peaking]
and [Magnification] to display the camera’s image in black & white while using the respective assistance
function.
- The assistance functions will not affect your recordings.
- You can set [F. ASSIST.] > [OPTIONS] > [Magnification] > [Available While Rec] to [On] to be
able to use magnification while recording a clip. However, in such case, you will not be able to use face
detection and tracking, or display the camera’s live view image on the Browser Remote screen.
Zq
One-Shot AF
In this focus mode, you will focus manually in most situations but still have the option to have the camera focus
automatically only once on the subject inside the AF frame that appears on the monitoring screen. You can also
change the size and position of the AF frame.
1 Set the focus mode switch on the lens to AF.
On a compatible EF Cinema/broadcast lens, enable automatic adjustment on the lens (A 89).
@
will appear at the left of the monitoring screen.
93
Adjusting the Focus
2 Open the focus [AF Mode] submenu.
Setup screen: [AF] > [OPTIONS] > [AF Mode]
Monitoring menu: [Camera Setup] (
v
) > [Focus] > [AF Mode]
3 Select [One Shot] and then press SET.
4 If necessary, change the size and position of the AF frame (A 95).
5 Press and hold the ONE-SHOT AF button.
A white AF frame will appear on the monitoring screen and the camera will focus automatically. When you
are using Face AF, the face detection frame around the face of the person who has been determined to be
the main subject will turn white.
When correct focus has been achieved, the AF frame turns green. If the camera cannot focus automatically,
the AF frame will turn red.
The AF frame will disappear when you release the ONE-SHOT AF button.
NOTES
NOTES
One-shot AF will not work in the following cases.
- When slow & fast motion recording is activated.
- When the shutter speed mode is set to [Slow] and the shutter speed is set to 1/4 or 1/3.
- When Face AF is set to [Face Only] and a face has not been detected.
- When a broadcast lens (A 240) is attached to the camera.
When the aperture value used is F11 or higher, Dual Pixel CMOS AF will not work and the camera will focus
using contrast-detection autofocus.
Zq
AF-Boosted MF
In this focus mode, you can focus manually most of the way and let the camera finish focusing automatically.
This is very convenient when you want to make certain that your clips shot at 4K and higher are in sharp focus.
Additionally, with this mode, if the camera cannot evaluate how to adjust the focus, it will not perform unreliable
focus adjustments. This results in an overall smoother focusing operation than with continuous AF.
1 Set the focus mode switch on the lens to AF.
On a compatible EF Cinema/broadcast lens, enable automatic adjustment on the lens (A 89).
@
will appear on the left of the monitoring screen.
2 Open the focus [AF Mode] submenu.
Setup screen: [AF] > [OPTIONS] > [AF Mode]
Monitoring menu: [Camera Setup] (
v
) > [Focus] > [AF Mode]
3 Select [AF-Boosted MF] and then press SET.
When the focus is in the manual adjustment range, a yellow focus frame will appear on the monitoring
screen.
4 If necessary, change the size and position of the AF frame (A 95).
5 Turn the focus ring to adjust the focus.
Focus manually to bring the subject closer into focus. When the focus enters the automatic adjustment
range, the focus frame will turn white and the camera will then finish focusing automatically.
While the focus stays within the automatic adjustment range, the camera will keep the subject in focus
automatically.
Adjusting the Focus
94
Zq
Continuous AF
The camera will focus automatically on a subject inside the main area of the image (approximately 80% of the
recording area).
1 Set the focus mode switch on the lens to AF
On a compatible EF Cinema/broadcast lens, enable automatic adjustment on the lens (A 89).
@
will appear on the left of the monitoring screen.
2 Open the focus [AF Mode] submenu.
Setup screen: [AF] > [OPTIONS] > [AF Mode]
Monitoring menu: [Camera Setup] (
v
) > [Focus] > [AF Mode]
3 Select [Continuous] and then press SET.
A white AF frame will appear on the monitoring screen. If necessary, change the size and position of the AF
frame (A 95).
When you are using Face AF, a white detection frame will appear around the face of the person who has
been determined to be the main subject.
NOTES
NOTES
About the autofocus (AF) functions:
The point where the camera focuses may change slightly depending on shooting conditions, such as subject,
brightness and zoom position. Check the focus before resuming shooting.
When the desired focus point (subject) is closer than the minimum focusing distance, the AF frame will turn red
at the end of the lens’s focusing range.
Autofocus may take longer in the following cases.
- When the frame rate set in the video configuration is set to 29.97P, 25.00P, 24.00P or 23.98P.
- With some EF lenses, the camera may take longer to focus automatically or may not be able to focus
correctly. Visit your local Canon Web site for the latest information.
When using autofocus with compatible EF lenses, you can change various aspects of the autofocus function
with the following settings. Visit your local Canon Web site for the latest information on lenses that support
these settings.
- [AF] > [OPTIONS] > [AF Speed] to set the AF speed (the speed at which the focus is adjusted) to
one of 10 levels.
- [AF] > [OPTIONS] > [AF Speed Limit] to select whether the selected AF speed is applied at all
times or only while recording.
- [AF] > [OPTIONS] > [AF Response] to set the responsiveness of the autofocus function to one of
7 levels.
- While using continuous AF, you can hold the ONE-SHOT AF button pressed down to temporarily adjust the
focus using the maximum AF speed and AF response. This is helpful when you want to focus quickly after
focus was lost or to keep a subject in focus while you follow it.
Continuous AF will not work in the following cases.
- When using an EF lens that does not have a focus mode switch.
- While adjusting the aperture, except when using an EF lens compatible with automatic aperture (A 240).
- While adjusting the focus using a remote controller attached to one of the REMOTE terminals.
- When slow & fast motion recording is activated.
- When a broadcast lens (A 240) is attached to the camera.
Autofocus may not work well on the following subjects or in the following cases. In such case, focus manually.
- When an ISO speed or gain value in the extended range is selected (A 76).
- Reflective surfaces
- Subjects with low contrast or without vertical lines
- Fast moving subjects
- Through dirty or wet windows
-Night scenes
- Subjects with a repetitive pattern
95
Adjusting the Focus
- When the [Gamma] setting in the custom picture file (A 134) is set to one of the Canon Log settings or
[Wide DR].
- When using small apertures.
- When subjects at different distances appear inside the AF frame.
AF Lock
While using continuous AF or AF-Boosted MF, you can lock the focus on a certain subject and then move the
camera to change the composition.
While the autofocus is active, press [AF] > [AF LOCK].
Alternatively, you can press an assignable button set to [AF Lock] (A 127).
The focus will be locked and
@
and the AF frame on the monitoring screen will turn gray. When you are
using Face AF, the face detection frame around the main subject will turn gray.
Press [AF LOCK] again to cancel the AF lock.
NOTES
NOTES
AF lock will be canceled automatically in the following cases:
- If the camera is turned off or the camera’s system frequency is changed.
- If the lens is removed or replaced.
- If the [AF] > [OPTIONS] > [AF Mode] setting is changed to [One Shot].
- If slow & fast motion recording is activated.
Zq
Changing the AF Frame Size and Position
You can change the size and position of the AF frame that appears on the monitoring screen while using one of
the autofocus functions. The size and position of face detection frames and tracking frames will change
automatically as the subject moves and its relative size changes within the frame.
1 Open the [AF Frame Position] submenu.
Setup screen: [AF] > [OPTIONS] > [AF Frame Position]
Monitoring menu: [Camera Setup] (
v
) > [Focus] > [AF Frame Position]
2 Select the desired option and then press SET.
3 From the same submenu select [AF Frame Size].
4 Select the desired option and then press SET.
Options for [AF Frame Position]
[Selectable]: You can move the AF frame using the joystick or SELECT dial on the optional viewfinder or by
pressing [F. ASSIST.] > [ FRAME] and then pressing [
Í
], [
Î
], [
Ï
], [
Ð
] on the
camera. Press [CENTER] (setup screen) or press the BACK button on the optional viewfinder to
return the AF frame to the center position.
[Center Frame]: A fixed AF frame appears at the center of the screen.
Options for [AF Frame Size]
[Large]: Standard AF frame size.
[Small]: Smaller AF frame size (about 1/3 the standard size).
Adjusting the Focus
96
Zq
Face Detection
When the face detection function is activated, the camera will detect people’s faces. When there are a number of
people in the picture, one person will be determined to be the main subject but you have the option to select a
different person as the main subject. The camera will keep tracking the main subject even when it moves.
You can use face detection with one of the autofocus functions to let the camera focus on the main subject
automatically (Face AF). You can also combine face detection with the focus guide (A 90) to help you focus on
the main subject manually.
1 Activate the face detection function.
Setup screen: [AF] > [FACE] (set it to [On])
Monitoring menu: [Camera Setup] (
v
) > [Focus] > [Face Detection] > [On]
Alternatively, you can press an assignable button set to [Face Detection] (A 127).
Press [FACE] again (setup screen) or select [Off] instead (monitoring menu) to turn off the function.
2 Open the [Face AF] submenu.
Setup screen: From the same [AF] screen select [OPTIONS] > [Face AF]
Monitoring menu: From the same submenu select [Face AF]
3 Select the desired option and then press SET.
Alternatively, you can press an assignable button set to [Face AF] (A 127).
or will appear at the left of the monitoring screen.
4 Point the camera at the subject.
A face detection frame will appear around all detected faces. The person identified as main subject will have
a face detection frame with small arrows (
Þ
) on the sides.
When the [Face Only] option is used, @ will appear in white when a face is detected and in gray when a
face is not detected.
During continuous AF, the camera will keep focusing on the main subject’s face. During one-shot AF, the
camera will focus on the main subject’s face while you hold the ONE-SHOT AF button pressed down.
If you use face detection together with the tracking function (A 97), the camera will be able to track the
selected main subject more reliably.
5 If necessary, change the main subject when there is more than one person detected in the frame.
Setup screen: In the [AF] screen’s or [Focus Assistance Functions] screen’s [Move frame] screen ( [AF]
or [F. ASSIST.] > [ FRAME]), press [
Ï
] or [
Ð
].
Monitoring screen: Push the joystick (left/right) or turn the SELECT dial on the optional viewfinder.
Options
[Face Priority]: When there is no face detected, the camera focuses automatically according to the AF mode
currently selected.
[Face Only]: When there is no face detected, the camera locks the focus.
Face AF operation by AF mode
[AF Mode] setting and focus operation
[Face AF] setting
[Face Priority] [Face Only]
Face detected No face detected Face detected No face detected
[One Shot] while the ONE-SHOT AF button is not pressed Manual focus
[One Shot] while the ONE-SHOT AF button is held pressed down
Focus on the
detected face
Focus on the
subject inside
the AF frame
Focus on the
detected face
Manual focus
[Continuous] (autofocus),
[AF-Boosted MF] within the automatic adjustment range
[AF-Boosted MF] within the manual adjustment range
(yellow AF frame)
Manual focus
97
Adjusting the Focus
NOTES
NOTES
In certain cases, faces may not be detected correctly. Typical examples include:
- Faces extremely small, large, dark or bright in relation to the frame.
- Faces that are turned to the side, at a diagonal, partially hidden or upside-down.
Face detection cannot be used in the following cases:
- When the shutter speed used is slower than 1/30 (59.94 Hz recordings), 1/25 (50.00 Hz recordings) or 1/24
(24.00 Hz recordings).
- When slow & fast motion recording is activated.
- When the second frame of the focus guide function is displayed.
- When a manual focus lens is attached to the camera.
- When [F. ASSIST.] > [OPTIONS] > [Magnification] > [Available While Rec] is set to [On].
The camera may mistakenly detect the faces of non-human subjects. In such case, turn face detection off.
Zq
Tracking a Specific Subject
You can have the camera track other moving subjects that are not faces and also combine the tracking function
with one of the autofocus functions to let the camera focus on the desired subject automatically.
1 Press [AF] > [TRACKING] to activate the tracking function.
Alternatively, you can press an assignable button set to [Tracking] (A 127).
The subject selection mark
I
will appear on the monitoring screen.
Press the BACK button to end the tracking function’s standby mode.
2 Place the center of the
I
mark on the subject you wish to track.
Setup screen: Press [
Í
], [
Î
], [
Ï
], [
Ð
].
Monitoring menu: Use the joystick on the optional viewfinder.
Press [CENTER] (setup screen) or press the BACK button on the optional viewfinder to return the
I
mark
to the center position.
3 Press [START
£
] (setup screen) or press SET on the optional viewfinder to start tracking the
subject.
If the tracking failed, the
I
mark will turn red momentarily. Select the subject again.
4 The face detection frame or
I
mark changes to a tracking frame and the camera will start tracking
the selected subject.
During continuous AF, the camera will keep focusing on the selected subject. During one-shot AF, the
camera will focus on the selected subject while you hold the ONE-SHOT AF button pressed down.
You can turn the SELECT dial on the camera to adjust the focus manually.
Press [CANCEL
£
] (setup screen) or press the BACK button on the optional viewfinder to end the tracking
function and return the camera to the focus mode that was used previously.
You can also press the assignable button set to [Tracking] to return to the tracking standby mode (subject
selection screen).
NOTES
NOTES
The camera may start tracking the incorrect subject if there is another subject in the picture with similar color/
pattern characteristics. In that case, select the desired subject again.
The tracking function cannot be used in the same cases as face detection (A 97).
Onscreen Markers, Zebra Patterns and False Color
98
Onscreen Markers, Zebra Patterns and False Color
Using onscreen markers allows you to make sure your subject is correctly framed and is within the appropriate
safe area. The zebra patterns help you identify areas that are overexposed. The false color display allows you to
check if the exposure is correct. You can choose to activate these assistance displays independently on the
optional viewfinder or on external monitors. The assistance displays will not affect your recordings.
Displaying Onscreen Markers
The camera offers 6 types of onscreen markers. You can display multiple onscreen markers simultaneously.
1 Open the [Markers] submenu.
[Assist. Functions] (
A
) > [Markers]
2 Select [VIDEO Output] and/or [MON.+HDMI Output], select [On] and then press SET.
Alternatively, you can press an assignable button set to [Markers: VIDEO] (optional viewfinder only),
[Markers: MON.+HDMI] (external monitors only) or [Markers] (all monitoring devices at once) (A 127).
Onscreen markers are activated on all video outputs by default. Select [Off] instead to not display the
onscreen markers on the respective video outputs.
3 Select a marker you wish to display, select the desired marker color and then press SET.
Select [Off] to turn off the selected marker.
You can display multiple markers simultaneously. Repeat this step as necessary.
If you selected [Safe Area] or [Aspect Marker], select the desired safe area or aspect ratio with the following
procedures (A 99).
Options
[Center]: Displays a small marker that indicates the center of the frame.
[Horizontal]: Displays a horizontal line to help you compose level shots.
[Grid]: Displays a grid that allows you to frame your shots correctly (horizontally and vertically).
[Aspect Marker]:Displays markers that indicate various aspect ratios to help you keep your shot within that area.
Available options for [Aspect Ratio] are [4:3], [13:9], [14:9], [16:9], [1.375:1], [1.66:1], [1.75:1],
[1.85:1], [1.90:1], [2.35:1], [2.39:1] and [Custom], a free aspect ratio set by the user.
[Safe Area]: Displays indicators that show various safe areas, such as the action safe area and text safe area.
You can select the core area used as the basis for calculating the safe area and a percentage
([80%], [90%], [92.5%] or [95%]), relative to that core area.
[Sub Rec Area]: Displays a marker that indicates the area covered by the sub recording.
Aspect guide 4:3
Center marker
Grid
Level marker
Safe area 80%
out of the whole
picture
Area covered by
the sub recording
99
Onscreen Markers, Zebra Patterns and False Color
To set the aspect ratio
1 Select [Aspect Ratio], select the desired option and then press SET.
If you selected one of the preset aspect ratios, the rest of the procedure is not necessary. If you selected
[Custom], continue the procedure to set the desired aspect ratio.
2 Select [Custom Ratio] and then press SET.
3 Set the desired aspect ratio using the keyboard screen (A 37).
To set the safe area
If an aspect marker is not selected, the safe area will be calculated as a percentage of the whole image ([Whole
Picture]) and you can only select the percentage (step 2). To calculate the safe area as a percentage of an aspect
ratio marker ([Selected Aspect Marker]), select an aspect ratio marker in advance and perform the procedure
from the beginning.
1 Select [Basis for Safe Area], select the desired option and then press SET.
2 Select [Safe Area %], select the desired percentage and then press SET.
NOTES
NOTES
The aspect ratio marker will not be displayed when the marker’s ratio (including custom ratios) matches that of
the resolution set in the video configuration.
Displaying Zebra Patterns
The camera has a zebra pattern function that shows black and white diagonal stripes over areas that
are overexposed. There are two types of zebra patterns and you can display both simultaneously.
Zebra 1 lets you identify areas within a certain range (±5% of a specified level from 5% to 95%) while
zebra 2 lets you identify areas that are over a specified level (from 0% to 100%). When you display
both simultaneously and they overlap, only the zebra 1 pattern will be displayed in those areas.
1 Open the [Zebra] submenu.
[Assist. Functions] (
A
) > [Zebra]
2 Select [VIDEO Output] and/or [MON.+HDMI Output], select [On] and then press SET.
Alternatively, you can press an assignable button set to [Zebra: VIDEO] (optional viewfinder only), [Zebra:
MON.+HDMI] (external monitors only) or [Zebra] (all monitoring devices at once) (A 127).
Select [Off] instead to not display the onscreen markers on the respective video outputs.
3 From the same submenu select [Select] to set the zebra pattern type.
4 Select [Zebra 1], [Zebra 2] or [Zebra 1+2] and then press SET.
5 From the same submenu select [Zebra 1 Level] or [Zebra 2 Level] to set the trigger level.
6 Select the desired value/range and then press SET.
NOTES
NOTES
When the HDMI OUT terminal’s resolution is set to 4096x2160 or 3840x2160, zebra patterns will not be
displayed on the monitor connected to the HDMI OUT terminal.
Zebra 1
Zebra 2
Onscreen Markers, Zebra Patterns and False Color
100
Using the False Color Display
The false color display is an assistance display mode that turns the image from the camera to black and white
and overlays on it 6 different colors to indicate important brightness ranges.
Press the FALSE COLOR button on the camera to turn on the false color display on external monitors
connected to the MON. terminals or the HDMI OUT terminal. Press the FALSE COLOR button on the
optional viewfinder to turn on the false color display on the viewfinder.
You can also set [Assist. Functions] > [False Color] > [VIDEO Output], [MON.1 Output],
[MON.2 Output] or [HDMI Output] to [On] to activate the false color display on the respective monitoring
devices.
Alternatively, you can press an assignable button set to [False Color: VIDEO] (optional viewfinder only), [False
Color: MON.+HDMI] (external monitors only), [False Color: MON.1], [False Color: MON.2], [False Color: HDMI]
(individual monitors) or [False Color] (all monitoring devices at once) (A 127).
NOTES
NOTES
You can use the [Assist. Functions] > [False Color] > [Color Index] setting to display an index of
the colors used in the false color display on the control display.
The false color display will not be output in the following cases.
- When the HDMI OUT terminal’s resolution is set to 4096x2160 or 3840x2160, the false color display will not
be displayed on the monitor connected to the HDMI OUT terminal.
- While color bars are being displayed (A 114).
Color Meaning
Red White clipping
Yellow Just below white clipping
Pink One stop over 18% gray
Green 18% gray
Blue Just above black clipping
Purple Black clipping
101
Setting the Time Code
Setting the Time Code
In shooting mode, the camera generates a time code signal and records it with the recorded clips. The time
code signal can be output from the SDI OUT terminals, MON. terminals and TIME CODE IN/OUT terminal. In
playback mode, the time code embedded in the clip being played back can be output from the SDI OUT
terminals and MON. terminals. You can also synchronize the camera’s time code with an external device
(A 106, 107).
Depending on the frame rate used, you may be able to select between a drop frame an non-drop frame time
code signal (A 102). The default mode varies depending on the country/region of purchase and, though the
time code display style is different for DF and NDF, in this section the NDF display style is used for simplicity’s
sake.
Selecting the Time Code Mode
1 Open the time code [Mode] submenu.
Setup screen: [OPTIONS] > [Mode]
Monitoring menu: [System Setup] (
B
) > [Time Code] > [Mode]
2 Select the desired option and then press SET.
Options
[Preset]: The time code starts from an initial value you can select in advance. The default initial time code
is 00:00:00:00.
See the following procedures to select the time code running mode and set the initial time code.
[Regen.]: The camera will read the selected recording media and the time code will continue from the last
time code recorded on the recording media. The time code runs only while recording so clips
recorded consecutively on the same recording media will have continuous time codes.
NOTES
NOTES
When the main recording format is set to [ProRes (CFast)] and a CFast card is not inserted in the camera, sub
recording clips will not be recorded even if an SD card is inserted in the camera. For this reason, when the time
code running mode is set to [Regen.], the last time code recorded on the SD card will not be read.
Setting the Time Code Running Mode
If you set the time code mode to [Preset], you can select the time code running mode.
1 Open the time code [Run] submenu.
Setup screen: [OPTIONS] > [Run]
Monitoring menu: [System Setup] (
B
) > [Time Code] > [Run]
2 Select the desired option and then press SET.
Options
[Rec Run]: The time code runs only while recording so clips recorded consecutively on the same recording
media will have continuous time codes.
[Free Run]: The time code starts running the moment you press SET and keeps running regardless of the
camera’s operation.
Setting the Time Code
102
Setting the Time Code’s Initial Value
If you set the time code mode to [Preset], you can set the initial value of the time code.
1 Open the time code setting screen.
Setup screen: [SET TC]
Monitoring menu: [System Setup] (
B
) > [Time Code] > [Setting] > [Set]*
* To reset the time code to [00:00:00.00], select [Reset] instead.
The time code setting screen appears with an orange selection frame indicating the hours.
2 Set the desired time code using the keyboard screen (A 37).
Camera menu only: Press [RESET] to reset the time code to [00:00:00.00].
If the running mode is set to [Free Run], the time code will start running from the selected time code the
moment you confirm the time code.
Selecting Drop or Non-Drop Frame
When the frame rate is set to 29.97P, 59.94i, or 59.94P, you can select between a drop frame (DF) or non-drop
frame (NDF) time code, depending on how you plan to use your recordings.
With all other frame rates, the time code is set to non-drop frame (NDF) and cannot be changed.
1 Open the [DF/NDF] submenu.
Setup screen: [OPTIONS] > [DF/NDF]
Monitoring menu: [System Setup] (
B
) > [Time Code] > [DF/NDF]
2 Select [DF] or [NDF] and then press SET.
The time code display will differ depending on the setting. When you select [DF], the time code will appear
as [00:00:00.00]; when you select [NDF], it will appear as [00:00:00:00].
Putting the Time Code Display on Hold
If you set an assignable button to [Time Code Hold] (A 127), you can press the button to freeze the display of
the time code*. While the time code display is put on hold, [H] will appear next to the time code on the HOME
screen and at the bottom right corner of the monitoring screen.
The time code continues to run normally while the time code display is on hold. When you resume the time code
display, the current time code will be displayed.
* The time code signal output from the SDI OUT terminals, MON. terminals and TIME CODE IN/OUT terminal will not be put on
hold. However, the time code displayed on a monitor connected to the HDMI OUT terminal will be put on hold.
About the Time Code Display
A letter may appear next to the time code depending on the operation. Refer to the following table.
Letter Description
R The time code mode is set to [Regen.].
P The time code mode is set to [Preset] and the running mode is set to [Rec Run].
F The time code mode is set to [Preset] and the running mode is set to [Free Run].
E Time code signal is coming from an external source.
H Time code display is on hold.
None Time code during clip playback.
103
Setting the Time Code
NOTES
NOTES
The frames value of the time code runs from 0 to 23 (frame rate set to 23.98P or 24.00P), from 0 to 24 (frame
rate set to 25.00P, 50.00i or 50.00P), or from 0 to 29 (all other frame rates).
When you mix drop frame and non-drop frame time codes, there might be a discontinuity in the time code at
the point where the recording starts.
When you are using the [Free Run] running mode, the time code will continue running as long as the lithium
button battery has some charge left, even if you disconnect all other power sources.
If you set an assignable button to [Time Code] (A 127), you can press the button to open the [Time Code]
submenu in the monitoring menu.
Setting the User Bit
104
Setting the User Bit
The user bit display can be selected from the date or the time of recording, or an identification code consisting of
8 characters in the hexadecimal system. There are sixteen possible characters: the numbers 0 to 9 and the
letters A to F. That user bit information can then be recorded with XF-AVC clips. If the camera is set to output the
time code (A 107), it will output also the user bit information.
If user bit information is being received along with an external time code, you can also record the external user bit
with XF-AVC clips (A 106).
1 Open the user bit setting screen.
Setup screen: [UB] > [SET UB]
Monitoring menu: [System Setup] (
B
) > [User Bit] > [Type] > [Setting] > [Set]*
* To reset the user bit to [00 00 00 00], select [Reset] instead.
The user bit setting screen appears with an orange selection frame on the leftmost character.
2 Set the desired user bit using the keyboard screen (A 37).
Setup screen only: Press [RESET] to reset the user bit to [00 00 00 00].
To use the date or time as user bit
1 Open the user bit [Type] submenu.
Setup screen: [UB] > [OPTIONS] > [Type]
Monitoring menu: [System Setup] (
B
) > [User Bit] > [Type]
2 Select [Time] or [Date] and then press SET.
105
Synchronizing with an External Device
Synchronizing with an External Device
Using Genlock synchronization, you can synchronize this camera’s video signal to that of an external video
device. Similarly, using an external time code signal, you can synchronize this camera’s time code to the external
signal. Using the external time code signal with multiple cameras allows you to set up a multi-camera recording.
You can also output the time code signal from this camera to achieve the same result. If you output the time
code from the SDI OUT terminals or MON. terminals to an editing device, the editor can create video with the
same time code.
Connecting an External Device
When synchronizing the camera using a reference video signal*, use the GENLOCK/SYNC OUT terminal. When
synchronizing a time code signal, use the TIME CODE terminal. Be sure to set either terminal to input or output
in advance.
Connect the external device to the camera as shown in the following diagram.
* As reference video signal (input signal) for Genlock synchronization, you can use an analog blackburst or tri-level HD signal. The
reference video output signal will be a tri-level HD signal.
Connection Diagram
GENLOCK/SYNC OUT
terminal
TIME CODE
IN/OUT
terminal
BNC cables
(commercially
available)
Synchronizing with an External Device
106
Reference Video Signal Input (Genlock Synchronization)
When a reference sync signal (tri-level HD signal or analog blackburst) is input through the GENLOCK/
SYNC OUT terminal, the phases of the camera’s V and H sync will automatically be synchronized to it. The
phase difference between the external Genlock signal and the camera is initially set to 0. The H phase can be
adjusted within the range of approximately ±0.4 H.
1 Open the GENLOCK/SYNC OUT terminals [Terminal Function] submenu.
[System Setup] (
B
) > [GENLOCK/SYNC OUT] > [Terminal Function]
2 Select [Genlock Input] and then press SET.
3 From the same submenu select [Genlock Adjustment].
4 Set the desired H phase adjustment value using the keyboard screen (A 37).
Camera menu only: Press [RESET] to reset the H phase adjustment to its previous value before the
adjustment.
NOTES
NOTES
When a suitable Genlock signal is input, the Genlock synchronization stabilizes after approximately
10 seconds.
When a suitable Genlock signal is detected, the
U
icon will flash on the HOME screen and at the bottom
right corner of the monitoring screen. When the camera locks on the external Genlock signal, the icon will stay
on.
If the external Genlock signal is incorrect, the synchronization may not be stable. In such case, the recorded
time code may be incorrect.
Time Code Signal Input
An external SMPTE-standard LTC timing signal received from the TIME CODE IN/OUT terminal can be recorded
as the time code. The user bit of the external timing signal can also be recorded with clips. Before connecting the
device, set the TIME CODE IN/OUT terminal to input with the procedure below and make sure the time code
running mode is set to [Free Run] (A 101).
1 Open the [TC In/Out] submenu.
Setup screen: [OPTIONS] > [TC In/Out]
Monitoring menu: [System Setup] (
B
) > [Time Code] > [TC In/Out]
2 Select [In] and then press SET.
Recording the User Bit of an External Signal
The user bit of an external time code signal can also be recorded with clips, along with the time code itself.
1 Open the user bit [Recording Mode] submenu.
Setup screen: [UB] > [OPTIONS] > [Recording Mode]
Monitoring menu: [System Setup] (
B
) > [User Bit] > [Recording Mode]
2 Select [External] and then press SET.
NOTES
NOTES
Synchronize the camera’s time code with an external time code signal that matches the camera’s system
frequency. Use a 24-frame time code signal when the frame rate is set to 23.98P or 24.00P, a 25-frame time
code signal when it is set to 25.00P, 50.00i or 50.00P and a 30-frame time code signal for other frame rates.
When a suitable external time code signal is received, the camera’s own time code will be synchronized to it
and the synchronization will be maintained even if you disconnect the cable from the TIME CODE IN/OUT
terminal.
107
Synchronizing with an External Device
When the camera locks on an external time code signal, [E] will appear next to the time code on the control
display and at the bottom right corner of the monitoring screen.
If the external time code signal is incorrect or there is no input signal, the internal time code set in the camera
will be recorded instead.
While a DF time code signal is being received, the external time code’s drop-frame bit will be used.
Performing any of the following actions while the cable is not connected will cause the synchronization to be
disrupted; the correct time code will be restored once you reconnect the cable.
- Turning the camera off or pressing the PLAY button (switching to playback mode)
- Changing the video configuration
Reference Video Signal Output
You can output the camera’s video signal as a reference sync signal (tri-level HD signal) to synchronize an
external device to this camera. The reference video signal output will have the same frequency as the signal
output from the SDI OUT terminals.
1 Open the GENLOCK/SYNC OUT terminal’s [Terminal Function] submenu.
[System Setup] (
B
) > [GENLOCK/SYNC OUT] > [Terminal Function]
2 Select [HD Sync Output] and then press SET.
If necessary, change the scan mode (P or PsF) with the [SYNC Scan Mode] setting in the same submenu.
Synchronization signals
* When slow & fast motion recording is activated, the signal output will change depending on the system frequency used:
1080/59.94i (59.94 Hz), 1080/50.00i (50.00 Hz) or 1080/60.00i (24.00 Hz). When slow & fast motion recording is activated while
[Camera Setup] > [Sensor Mode] is set to [Super 16mm (Cropped)], the signal output will always be 1080/60.00i.
Time Code Signal Output
The time code will be output from the TIME CODE IN/OUT terminal as a SMPTE-standard LTC timing signal. The
user bit will also be output. Additionally, the time code will be output from the SDI OUT terminals and MON.
terminals.
To output the time code signal from the TIME CODE IN/OUT terminal, set [OPTIONS] > [TC In/Out] to
[Out] to change the terminal’s function to output (A 106).
NOTES
NOTES
The time code will not be output when slow & fast motion recording is activated or during playback.
When the sensor mode is set to [Full Frame] and the frame rate is set to 59.94P or 50.00P, the time code will
not be output from the MON. terminals.
Video output from the SDI OUT terminals
Signal output from the SYNC OUT
terminal (tri-level HD signal)
Resolution Frame rate
4096x2160
3840x2160
2048x1080
1920x1080
29.97P 1080/29.97 (P/PsF)
25.00P 1080/25.00 (P/PsF)
24.00P 1080/24.00 (P/PsF)*
23.98P 1080/23.98 (P/PsF)
4096x2160
3840x2160
2048x1080
1920x1080
59.94i / 59.94P 1080/59.94i
50.00i / 50.00P 1080/50.00i
Recording Audio
108
Recording Audio
The camera features 4-channel linear PCM (24 bit, 48 kHz) audio recording and playback. You can record audio
using the INPUT terminals (commercially available microphones, analog line-in audio sources, AES/EBU digital
audio sources), the MIC terminal (commercially available microphones) or the built-in monaural microphone*.
The audio signal will be output with the video signal from the SDI OUT terminals, MON. terminals and HDMI OUT
terminal. You can record this audio signal on an external recorder.
* Only for recording notes while shooting.
Audio Settings and Recorded Audio Channels
Which audio inputs are recorded to which audio channels is determined by a combination of menu settings and
audio-related controls on the camera.
The following table gives an overview of the possible combinations.
I
[CH1/2 IN]* [CH3/4 IN]*
Audio input selection
switches
[CH2 Input]**
Recorded audio channels/audio sources
for INPUT 1 for INPUT 2 CH1 CH2 CH3 CH4
[INPUT
Terminals]
[MIC Terminal] AES/EBU
INPUT 1 terminal (digital audio) MIC terminal (L) MIC terminal (R)
[INPUT
Terminals]
[INPUT
Terminals]
AES/EBU AES/EBU
INPUT 1 terminal (digital audio) INPUT 2 terminal (digital audio)
[INPUT
Terminals]
[INPUT
Terminals]
AES/EBU ANALOG
INPUT 1 terminal (digital audio)
INPUT 2 terminal
[INPUT
Terminals]
[Monaural Mic] AES/EBU
INPUT 1 terminal (digital audio)
Built-in microphone
(mono)
Built-in microphone
(mono)
[INPUT
Terminals]
[MIC Terminal] ANALOG
[INPUT 2] INPUT 1 terminal INPUT 2 terminal MIC terminal (L) MIC terminal (R)
[INPUT
Terminals]
[MIC Terminal] ANALOG
[INPUT 1] INPUT 1 terminal INPUT 1 terminal MIC terminal (L) MIC terminal (R)
[INPUT
Terminals]
[INPUT
Terminals]
ANALOG AES/EBU [INPUT 1] INPUT 1 terminal INPUT 1 terminal INPUT 2 terminal (digital audio)
[INPUT
Terminals]
[INPUT
Terminals]
ANALOG AES/EBU [INPUT 2] INPUT 1 terminal
INPUT 2 terminal (digital audio)
[INPUT
Terminals]
[INPUT
Terminals]
ANALOG ANALOG [INPUT 2] INPUT 1 terminal INPUT 2 terminal INPUT 1 terminal INPUT 2 terminal
[INPUT
Terminals]
[INPUT
Terminals]
ANALOG ANALOG [INPUT 1] INPUT 1 terminal INPUT 1 terminal INPUT 1 terminal INPUT 2 terminal
INPUT terminals’ audio
input selection switches
ANALOG switches
(INPUT terminals’
analog audio source
selection)
109
Recording Audio
*
[AUDIO] > [CH1/2 IN] and [CH3/4 IN] settings.
**
[AUDIO] > [OPTIONS] > [Audio Input] > [CH2 Input] setting.
NOTES
NOTES
On the [AUDIO] screen, you can check the audio input source, audio level adjustment mode
(A – automatic/M – manual) and audio level indicator for each of the audio channels.
Connecting an External Microphone or External Audio Input Source to the Camera
To each of the INPUT terminals you can attach commercially available microphones, digital audio sources (AES/
EBU), or analog line in sources with an XLR connector. To the MIC terminal you can attach commercially
available condenser microphones with their own power supply, and a 3.5 mm stereo mini plug.
Using the supplied microphone holder, you can fix external microphones with a diameter of 19 mm to 24 mm.
Follow the procedure below to attach a microphone (refer also to the following illustration). To connect an
external audio device to the camera, plug the device’s cable into the desired INPUT terminal (). The following
procedure and illustrations assume that the supplied microphone holder is attached to the camera (A 43).
1 Loosen the microphone lock screw (), open the
microphone holder and insert the microphone ().
2 Tighten the lock screw and put the microphone
cable through the cable clamp under the
microphone holder ().
3 Plug the microphone cable into the desired INPUT
terminal () or the MIC terminal ().
[INPUT
Terminals]
[Monaural Mic] ANALOG
[INPUT 2] INPUT 1 terminal INPUT 2 terminal
Built-in microphone
(mono)
Built-in microphone
(mono)
[INPUT
Terminals]
[Monaural Mic] ANALOG
[INPUT 1] INPUT 1 terminal INPUT 1 terminal
Built-in microphone
(mono)
Built-in microphone
(mono)
[MIC Terminal]
[INPUT
Terminals]
ANALOG
MIC terminal (L) MIC terminal (R) INPUT 1 terminal INPUT 2 terminal
[MIC Terminal]
[INPUT
Terminals]
AES/EBU
MIC terminal (L) MIC terminal (R) INPUT 2 terminal (digital audio)
[MIC Terminal] [MIC Terminal]
MIC terminal (L) MIC terminal (R) MIC terminal (L) MIC terminal (R)
[MIC Terminal] [Monaural Mic]
MIC terminal (L) MIC terminal (R)
Built-in microphone
(mono)
Built-in microphone
(mono)
[Monaural Mic]
[INPUT
Terminals]
ANALOG
Built-in microphone
(mono)
Built-in microphone
(mono)
INPUT 1 terminal INPUT 2 terminal
[Monaural Mic] [MIC Terminal]
Built-in microphone
(mono)
Built-in microphone
(mono)
MIC terminal (L) MIC terminal (R)
[Monaural Mic]
[INPUT
Terminals]
AES/EBU
Built-in microphone
(mono)
Built-in microphone
(mono)
INPUT 2 terminal (digital audio)
[Monaural Mic] [Monaural Mic]
Built-in microphone
(mono)
Built-in microphone
(mono)
Built-in microphone
(mono)
Built-in microphone
(mono)
[CH1/2 IN]* [CH3/4 IN]*
Audio input selection
switches
[CH2 Input]**
Recorded audio channels/audio sources
for INPUT 1 for INPUT 2 CH1 CH2 CH3 CH4
Microphone
lock screw
Recording Audio
110
Setting the Audio Input Type for the INPUT 1/INPUT 2 Terminals
Using the INPUT 1/INPUT 2 terminals, you can record audio independently to two audio channels from a
microphone or audio input source.
On the camera, set the audio-related switches for the INPUT terminal you wish to use according to the type of
audio input you wish to use.
1 Set the audio input selection switch for the desired INPUT terminal to AES/EBU (digital audio) or
ANALOG (analog audio).
2 If you selected analog audio, set the INPUT terminal’s ANALOG (analog source selection) switch to
MIC (microphone) or LINE (audio device).
To supply a microphone with phantom power, set the switch to MIC+48V instead. Make sure to connect the
microphone first, before turning the phantom power on. Keep the microphone connected when turning off
the phantom power.
When using the INPUT terminals to record to only one channel, use the INPUT 1 terminal.
MIC terminal
Cable clamp
INPUT 1 terminal
INPUT 2 terminal
About the monaural microphone
The monaural microphone allows you to add comments while shooting,
which can be synchronized to the audio and video during editing.
NOTES
NOTES
The audio recording level of the monaural microphone is adjusted
automatically and cannot be changed.
Monaural
microphone
111
Recording Audio
IMPORTANT
When connecting an analog microphone or device that does not support phantom power, make sure to set
the corresponding INPUT switch to MIC or LINE, respectively. If you set the switch to MIC+48V, the
microphone or device may be damaged.
Selecting the Audio Input Source for Audio Channels
You can select the audio input source that will be recorded on CH1/CH2 or CH3/CH4, independently for each
pair of audio channels. For details refer to the
Audio Settings and Recorded Audio Channels
table (A 108).
1 Select the desired pair of audio channels.
Setup screen: [AUDIO] > [CH1/2 IN] or [CH3/4 IN]
Monitoring menu: [Audio Setup] (
¡
) > [Audio Input] > [Select CH1/2 Input] or [Select CH3/4 Input]
2 Select [INPUT Terminals] (external microphone or audio device), [MIC Terminal] (external
microphone) or [Monaural Mic] (built-in microphone) and then press SET.
If necessary, repeat steps 1 and 2 to select the audio input source for the other pair of audio channels.
Recording a Single Analog Audio Input to Two Audio Channels
By default, when using analog audio sources (line in or microphone) connected to the INPUT terminals, each
audio input is recorded to a separate audio channel (INPUT 1 to CH1 and INPUT 2 to CH2).
If necessary (for example, as an audio backup recording), you can record the same analog audio source
connected to the INPUT 1 terminal to both audio channels, CH1 and CH2. In that case, you can adjust the audio
recording levels of each channel independently of each other.
1 Open the [CH2 Input] submenu.
Setup screen: [AUDIO] > [OPTIONS] > [Audio Input] > [CH2 Input]
Monitoring menu: [Audio Setup] (¡) > [Audio Input] > [CH2 Input]
2 Select the desired option and then press SET.
Options
[INPUT 2]: Records audio to each channel separately. Analog audio input into INPUT 1 is recorded to CH1,
while audio input into INPUT 2 is recorded to CH2.
[INPUT 1]: Analog audio input into INPUT 1 is recorded to both channels. Audio input into INPUT 2 will not
be recorded.
Adjusting the Audio Recording Level
When a channel is set to an analog audio input, you can select the automatic audio recording level adjustment or
adjust the audio level manually, independently for each channel. When a channel is set to a digital audio source
or the built-in monaural microphone, the audio recording level cannot be adjusted.
Repeat the following procedure as necessary to adjust the audio recording level for the audio channels used.
1 Open the [Audio Rec Level] screen/submenu of the desired audio channel.
Setup screen: [AUDIO] >[REC LEVEL] > Desired audio channel(s) ([CH1] to [CH4], [CH1/2],
[CH3/4])
Monitoring menu: [Audio Setup] (
¡
) > [Audio Input] > [Audio Rec Level CH1] to
[Audio Rec Level CH4], [Audio Rec Level CH1/2] or [Audio Rec Level CH3/4]
Recording Audio
112
2 Select automatic or manual audio level adjustment.
Setup screen: Press [A M] to switch between A (automatic) and M (manual) adjustment mode.
Monitoring menu: Select [Automatic] or [Manual] and then press SET.
If you selected automatic audio level, the rest of the procedure is not necessary.
If you selected manual audio level, continue the procedure to adjust the audio recording level. On the control
display the current audio level will be marked with an orange selection frame.
3 Monitoring menu only: From the same submenu select [CH1 Level] to [CH4 Level], [CH1/2 Level] or
[CH3/4 Level] according to the audio channel selected in step 1.
4 Turn the SELECT dial to set the audio recording level and then press SET.
For reference, 0 corresponds to –G, 50 corresponds to 0 dB, and 100 corresponds to +18 dB.
As a guideline, adjust the audio recording level so that the audio level meter will go to the right of the –18 dB
mark (one mark right of the –20 dB mark) only occasionally.
NOTES
NOTES
When both CH1 and CH2, or CH3 and CH4, are set to the INPUT terminals and to the same type of analog
audio source (external microphone or external line input), if both channels are also set to automatic audio level
adjustment, you can use the [AUDIO] > [OPTIONS] > [Audio Input] > [CH1/CH2 ALC Link] and
[CH3/CH4 ALC Link] settings to link the audio level adjustment of both channels.
If at least one of the channels is set to the INPUT terminals, an analog audio source and manual audio level
adjustment, you can activate the audio limiter to prevent audio distortions. When activated, the audio limiter
will limit the amplitude of audio input signals when they start to distort. Use the [AUDIO] > [OPTIONS]
> [Audio Input] > [INPUT 1&2 Limiter] setting.
We recommend using headphones when adjusting the audio level. If the input level is too high, audio may
become distorted even if the audio level indicator shows an appropriate level.
If you set an assignable button to [Audio Lvl Indicator] (A 127), you can press the button to turn on and off
the audio level indicator that appears at the right of the monitoring screen.
Additional Settings for External Analog Microphones
Microphone Sensitivity (INPUT Terminals)
When the audio input selection switch for INPUT 1 or INPUT 2 is set to ANALOG and the corresponding
ANALOG (analog source selection) switch is set to MIC or MIC+48V, you can select the external microphone’s
sensitivity.
1 Open the desired INPUT terminal’s sensitivity submenu.
Setup screen: [AUDIO] > [OPTIONS] > [Audio Input] > [INPUT 1 Mic Trim] or [INPUT 2 Mic Trim]
Monitoring menu: [Audio Setup] (
¡
) > [Audio Input] > [INPUT 1 Mic Trim] or [INPUT 2 Mic Trim]
2 Select the desired level and then press SET.
You can select one of 5 sensitivity levels from –12 dB to +12 dB.
113
Recording Audio
Microphone Attenuator (INPUT Terminals)
When the audio input selection switch for INPUT 1 or INPUT 2 is set to ANALOG and the corresponding
ANALOG (analog source selection) switch is set to MIC or MIC+48V, you can activate the external microphone’s
attenuator (20 dB).
1 Open the desired INPUT terminal’s microphone attenuator submenu.
Setup screen: [AUDIO] > [OPTIONS] > [Audio Input] > [INPUT 1 Mic Att.] or [INPUT 2 Mic Att.]
Monitoring menu: [Audio Setup] (
¡
) > [Audio Input] > [INPUT 1 Mic Att.] or [INPUT 2 Mic Att.]
2 Select [On] and then press SET.
Low Cut Filter (MIC Terminal)
When an audio channel is set to the MIC terminal, you can activate the low-cut filter, for example to reduce the
sound of wind in the background when recording outdoors.
1 Open the [MIC Low Cut] submenu.
Setup screen: [AUDIO] > [OPTIONS] > [Audio Input] > [MIC Low Cut]
Monitoring menu: [Audio Setup] (
¡
) > [Audio Input] > [MIC Low Cut]
2 Select [On] and then press SET.
When you select [On], some low-frequency sounds may be suppressed along with the sound of wind.
Microphone Attenuator (MIC Terminal)
When an audio channel is set to the MIC terminal, if the audio level is too high and the sound sounds distorted,
you can activate the microphone attenuator (20 dB).
1 Open the [MIC Att.] submenu.
Setup screen: [AUDIO] > [OPTIONS] > [Audio Input] > [MIC Att.]
Monitoring menu: [Audio Setup] (
¡
) > [Audio Input] > [MIC Att.]
2 Select [On] and then press SET.
Monitoring the Audio with Headphones
Connect headphones with a 3.5 mm stereo mini-plug to the
×
(headphone) terminal to monitor the recorded
audio.
NOTES
NOTES
You can adjust the headphone volume using the [AUDIO] > [
×
] setting (in shooting mode) or
> [Audio Setup] > [Headphone Volume] setting (in playback mode).
If you set an assignable button to [Headphones +] or [Headphones –] (A 127), you can press the button to
adjust the headphone volume without using the menu.
Colors Bars/Audio Reference Signal
114
Colors Bars/Audio Reference Signal
You can have the camera generate color bars and a 1 kHz audio reference signal and output them from the
VIDEO terminal (optional viewfinder, color bars only), SDI OUT terminals, MON. terminals, HDMI OUT terminal
and × (headphone) terminal (audio reference signal only). If the main recording format is set to [XF-AVC (CFast)],
the color bars and audio reference signal are recorded on clips recorded on a CFast card or SD card.
Color Bars
The camera offers 3 types of color bars (SMPTE, EBU or ARIB).
1 Open the [Activate] submenu to activate the color bars.
[Camera Setup] (
v
) > [Color Bars] > [Activate]
Alternatively, you can press an assignable button set to [Color Bars] (A 127).
2 Select [On] and then press SET.
The selected color bars appear on the monitoring screen.
3 From the same submenu select [Type] and then press SET.
4 Select the type of color bars and then press SET.
Turning off the camera or pressing the PLAY button (switching to playback mode) will deactivate the color
bars.
NOTES
NOTES
When the main recording format is set to one of the ProRes or RAW options, color bars will not be displayed
or output.
Audio Reference Signal
The camera can output a 1 kHz audio reference signal with the color bars.
1 Open the [1 kHz Tone] submenu.
Setup screen: [AUDIO] > [OPTIONS] > [Audio Input] > [1 kHz Tone]
Monitoring menu: [Audio Setup] (
¡
) > [Audio Input] > [1 kHz Tone]
2 Select the desired level (–12 dB, –18 dB or –20 dB) and then press SET.
Select [Off] to turn off the signal.
115
Waveform Monitor
Waveform Monitor
The camera can display a simplified waveform monitor on the monitoring screen. You can select one of 6 types
of monitors and also adjust the waveform amplification.
Displaying the Waveform Monitor
Press the WFM button.
The waveform monitor window will appear at the right of the monitoring screen on external monitors
connected to one of the MON. terminals or the HDMI OUT terminal.
You can also set [Assist. Functions] > [Waveform Monitor] > [VIDEO Output] and/or
[MON.+HDMI Output] to [On] to display the waveform monitor on the respective monitoring devices.
Alternatively, you can press an assignable button set to [WFM: VIDEO] (optional viewfinder only), [WFM:
MON.+HDMI] (external monitors only), or [Waveform Monitor] (all monitoring devices at once) (A 127).
You can use the [Assist. Functions] (
A
) > [Waveform Monitor] > [Position] setting to select
the position of the waveform monitor on the screen (left or right side).
Configuring the Waveform Monitor
1 Open the waveform monitor’s [Type] submenu.
[Assist. Functions] (
A
) > [Waveform Monitor] > [Type]
2 Select the desired option and then press SET.
If you selected [Select Line], continue the procedure to set the Y coordinate of the line you wish to display.
Otherwise, skip to step 5 to change the gain.
3 From the same submenu, select [Select Line] and then press SET.
4 Enter the Y coordinate of the desired line using the keyboard screen (A 37).
While recording, when the vertical resolution (number of horizontal lines) is 1080, you can select a value
between 0 and 1079 (1-line increments); when the vertical resolution is a value other than 1080, you can
select a value between 0 and the <vertical resolution – 2> (2-line increments).
During playback, depending on the clip’s resolution, you can select a value from one of the following ranges.
0 to 1079 (1-line increments)
0 to 2158 (2-line increments)
0 to 3138 (2-line increments)*
* qr only.
5 From the same submenu select [Gain] and then press SET.
6 Select the desired amplification ratio and then press SET.
If you selected [1x], the rest of the procedure is not necessary. If you selected [2x], the display range of the
waveform monitor’s Y axis will be reduced by half. Continue the procedure to select the minimum luminance
value (in %) shown on the Y axis.
7 From the same submenu select [Y Position] and then press SET.
8 Select the desired percentage and then press SET.
Options
[Line]: Sets the waveform monitor to line display mode.
[Line+Spot]: The waveform of the area in the red frame is displayed in red on top of the [Line] mode
waveform.
[Select Line]: The selected horizontal line will be displayed along with its waveform.
[Field]: Sets the waveform monitor to field display mode.
Waveform Monitor
116
[RGB]: Functions like an RGB parade scope.
[YPbPr]: Functions like a YPbPr parade scope.
NOTES
NOTES
The waveform monitor will not be affected even if a LUT is applied to the video output.
The waveform monitor cannot be displayed while magnification is activated.
If the [Knee] settings in the custom picture file (A 135) were changed, a horizontal line will appear on the
waveform monitor indicating the luminance (Y) level corresponding to the knee point.
117
Adding an $ Mark or % Mark to a Recording
Adding an
$
Mark or
%
Mark to a Recording
After making an important recording, you can add an OK mark (
$
) or check mark (
%
) to the clip (XF-AVC clips
on the CFast card only) to flag it and set it apart. You can use the
$
mark to protect important clips, as clips
with an
$
mark cannot be deleted using the camera.
To add an
$
mark or
%
mark to a clip, you must first set in advance an assignable button to [Add
$
Mark] or
[Add
%
Mark].
1 Set an assignable button to [Add
$
Mark] or [Add
%
Mark] (A 127).
To add both types of clip marks (to different clips), set one assignable button to [Add
$
Mark] and another
assignable button to [Add
%
Mark].
2 When you finish recording a clip you wish to mark, press the assignable button.
A message indicating the clip mark will appear on the monitoring screen and the selected clip mark will be
added to the XF-AVC clip.
NOTES
NOTES
A clip cannot have both an
$
mark and a
%
mark at the same time.
Using Metadata
118
Using Metadata
The camera automatically adds metadata to XF-AVC clips while they are being recorded. You can use Canon XF
Utility to check and search for specific metadata. You can also create and transfer a user memo remotely using
Browser Remote on a connected network device (A 170, 180).
Metadata components
1
User memo files need to be created using the software and saved on an SD card in advance.
2
Only when an optional GP-E1 GPS Receiver is attached to the camera. While recording, GPS information is recorded
automatically by the camera (A 120).
3
GPS information can only be added to clips already recorded.
4
Recording data is logged automatically by the camera.
Setting a User Memo Created with Canon XF Utility
Before you can add a user memo, you must first download and install Canon XF Utility (A 161). Next, create
the user memo and then save it to an SD card. Once you insert the SD card in the camera and select the user
memo, it will be added to clips you record.
1 Use Canon XF Utility to save a user memo file to an SD card.
For details, refer to
Managing User Memo Profiles
in the Canon XF Utility Instruction Manual.
2 Insert the SD card into the camera’s SD card slot.
3 Open the metadata [Setting] submenu.
[Rec/Media Setup] (
3
) > [Metadata] > [Setting]
4 Select [SD Card] and then press SET.
5 From the same submenu select [User Memo] and select the file name of the desired user memo file.
Select [Off] to record clips without a user memo.
6 Press [OK] (camera menu) or press SET (monitoring menu).
NOTES
NOTES
After you set a user memo, do not remove the SD card while you are recording. If the SD card is removed, the
user memo will not be added to the clip.
You must set the user memo before you start recording for it to be added to the clip. You cannot change the user
memo already added to a clip using the camera but you can do so with Canon XF Utility.
When the optional GP-E1 GPS Receiver is attached to the camera and the GPS function is activated, the user
memo information will not be recorded, even if you have selected a user memo file from the SD card.
Metadata
Entering content Checking content
Camera Canon XF Utility Browser Remote Canon XF Utility
User Memo: clip title, creator, location and description. Ü
1
Ü Ü
GPS information: altitude, latitude and longitude. Ü
2
Ü
3
Ü Ü
Information about the recording: scene and take. Ü Ü
Information about camera settings: shutter speed, ISO
speed/gain value, etc.
4
Ü
Unique Material Identifiers (UMID): country, organization
and user codes based on the SMPTE standard.
Ü
(A 194)
119
Using Metadata
Entering Information About the Recording
You can enter scene and take information to help identify the recording later on.
1 Open the [Scene] or [Take] submenu.
Camera menu: [Rec/Media Setup] > [Metadata] > [Scene] or [Take]
Monitoring menu: [Rec/Media Setup] (3) > [Metadata] > [Scene] or [Take] > [Set]*
* To clear the scene/take information, select [Reset] instead.
2 Enter the desired text using the keyboard screen (A 37).
Recording GPS Information (Geotagging)
120
Recording GPS Information (Geotagging)
When the optional GP-E1 GPS Receiver is attached to the camera’s system extension terminal, the camera will
automatically record GPS information (latitude, longitude and altitude) as part of the metadata of XF-AVC clips
(A 118). Later, the GPS information can be used to organize and search clips using Canon XF Utility (A 161).
For details about attaching and configuring the receiver, refer to the GP-E1’s instruction manual.
Attaching the GPS Receiver
1 Press the
Q
button to turn off the camera.
2 Attach the optional GP-E1 GPS Receiver to the camera’s
system extension terminal.
3 Fasten the GPS receiver’s locking screw.
4 Attach the supplied extension unit attachment bracket to
secure the GPS receiver.
NOTES
NOTES
Do not lay cables connected to the SDI OUT terminals,
MON. terminals or HDMI OUT terminal near the GPS
receiver. Doing so may negatively affect the GPS signal
reception.
Activating the GPS Receiver
1 Open the GPS [Activate] submenu.
[System Setup] (
B
) > [GPS] > [Activate]
2 Select [On] and then press SET.
The icon appears on the HOME screen and at the top left of the monitoring screen. It will flash as the
receiver tries to acquire satellite signals.
When satellite signals are correctly acquired, the icon will stay continuously on. GPS functions will be
activated and clips recorded thereafter will be geotagged.
IMPORTANT
In certain countries/regions, the use of GPS may be restricted. Be sure to use the GPS receiver in accordance
with local laws and regulations of the country/region where the receiver is used. Be particularly careful when
traveling outside of your home country.
Be careful about using the GPS receiver in places where the use of electronic devices is restricted.
The GPS information recorded with clips may contain data that can lead others to locate or identify you. Be
careful when sharing geotagged recordings with others or when uploading them to the Web.
Do not leave the GPS receiver near strong electromagnetic fields such as near powerful magnets and motors.
Adjusting the date/time automatically according to GPS position
You can set [System Setup] > [GPS] > [Auto Time Setting] to [On], to have the camera
automatically adjust its date and time settings according to the information received from the GPS signal. The
date and time will be updated automatically the first time a correct GPS signal is acquired after turning on the
camera.
While the automatic date/time adjustment is activated, the [System Setup] > [Set Clock] submenu
will not be available.
121
Recording GPS Information (Geotagging)
NOTES
NOTES
You can use the [System Setup] > [GPS] > [Display Info] setting to display the information
received from the GPS signal.
After replacing the power source or when first turning on the camera, it may take longer for the GPS receiver
to start receiving the GPS signal.
The GPS information recorded with clips corresponds to the location at the start of the recording.
Using Anamorphic Lenses
122
Using Anamorphic Lenses
You can attach an anamorphic lens to the camera and set the anamorphic desqueeze ratio used to display the
image from the camera on monitoring devices while shooting or during playback.
1 Open the [Anamorphic] submenu.
[Monitoring Setup] (
¢
) > [Anamorphic]
2 Select [VIDEO Output] and/or [MON.+HDMI Output], select [On] and then press SET.
Alternatively, you can press an assignable button set to [Anamorphic: VIDEO] (optional viewfinder only),
[Anamorphic: MON.+HDMI] (external monitors only) or [Anamorphic] (all monitoring devices at once)
(A 127).
3 From the same submenu select [Desqueeze Ratio].
4 Select the desired option and then press SET.
You can select a fixed desqueeze factor (x1.3 or x2.0) or use the lens’s squeeze factor as defined in the
metadata ([Lens Squeeze Factor]).
NOTES
NOTES
You can record the lens’s squeeze factor in the clip’s metadata with the [Rec/Media Setup] >
[Metadata] > [Lens Squeeze] setting.
In the following cases the image from the camera will not be desqueezed.
- When the HDMI OUT terminal’s resolution is set to 4096x2160 or 3840x2160, the image will not be
desqueezed on the monitor connected to the HDMI OUT terminal.
- During photo playback.
- The camera’s live view image in the Browser Remote application.
123
Using the Optional RC-V100 Remote Controller
Using the Optional RC-V100 Remote Controller
You can connect the optional RC-V100 Remote Controller to the camera’s REMOTE A terminal or REMOTE
B terminal in order to control the camera (including advanced recording functions) from a distance. In addition to
turning the camera on and off and navigating the menu, you can control various shooting related functions such
as aperture and shutter speed, and custom picture settings like knee and sharpness. When you use the
REMOTE B terminal to connect the RC-V100, the camera can receive and process multiple simultaneous
commands from the remote controller.
For details on how to connect and use the remote controller, refer to its instruction manual.
1 Turn off the camera and connect the optional RC-V100 Remote Controller to the camera.
Make sure that the remote controllers terminal selection switch is set to match the terminal to be used on
the camera.
2 Turn on the camera and open the [REMOTE Term.] submenu.
[System Setup] (
B
) > [REMOTE Term.]
3 Select [RC-V100 (REMOTE A)] or [RC-V100 (REMOTE B)] depending on the terminal used and then
press SET.
Options
[RC-V100 (REMOTE A)] or [RC-V100 (REMOTE B)], depending on the terminal used:
Select this option to use the optional RC-V100 Remote Controller connected to the
corresponding REMOTE terminal.
[Standard]: Select this option to use commercially available remote controls.
NOTES
NOTES
The following controls on the remote controller will not operate the camera: AGC button and AUTO KNEE
button.
The AUTO IRIS button on the remote controller will have an effect only when a compatible EF lens (A 240) is
attached to the camera.
The ZOOM dial on the remote controller will have an effect only when a compatible EF Cinema/broadcast lens
(A 240) is attached to the camera.
Adjusting custom picture related settings with the remote controller will have an effect only when the editing of
the custom picture file’s detailed settings ([Other Settings] > [Activate]) is enabled (A 131).
The REMOTE A and REMOTE B terminals cannot be used at the same time.
RR-10 or RR-100 8-pin
Remote Cable (optional)
To the RC-V100’s
REMOTE A terminal
To the RC-V100’s
REMOTE B terminal
Remote cable
(supplied with the RC-V100)
Using the Optional RC-V100 Remote Controller
124
If you plan on connecting the remote controller to the camera using the optional RR-10 or RR-100 8-pin
Remote Cable, check the serial number of the RC-V100. If the serial number starts with “01 xxxx” (where xxxx
represents other digits), you will need to update the remote controller’s firmware. Canon will perform this
feature upgrade, and requires that the remote controller be sent to an accredited Canon Service Center.
Shipping and handling charges may apply. Contact a Canon Customer Support Center for details.
125
Taking Photos
Taking Photos
You can take photos when the camera is in record standby mode. Photos are saved onto the SD card and their
size depends on the video configuration currently in use.
Taking Photos
To take a photo, set an assignable button to [Photo] in advance.
1 Set an assignable button to [Photo] (A 127).
2 When the camera is in record standby mode, press the assignable button to take a photo.
{
will appear momentarily on the HOME screen and at the top right of the monitoring screen.
The SD card access indicator will illuminate in red as the photo is being recorded.
IMPORTANT
Observe the following precautions while the SD card access indicator is illuminated in red. Failure to do so may
result in permanent data loss.
- Do not remove the power source or turn off the camera.
- Do not remove the SD card.
NOTES
NOTES
If the LOCK switch on the SD card is set to prevent writing, you will not be able to record photos. Change the
position of the LOCK switch in advance.
Photo Numbering
Photos are automatically assigned consecutive numbers and stored on the SD card in folders. You can select
the photo numbering method to be used.
1 Open the [Photo Numbering] submenu.
[Rec/Media Setup] (
3
) > [Photo Numbering]
2 Select the desired option and then press SET.
Options
[Reset]: Photo numbers will restart from 100-0001 every time you insert a new SD card. If an SD card
already contains previous recordings, photo numbers will continue from the number following
that of the last photo on the SD card.
[Continuous]: Photo numbers will continue from the number following that of the last photo recorded with the
camera. This setting is the most convenient for managing files on a computer. We recommend
using the [Continuous] setting.
Resolution Photo size Approximate file size per image
qr
5952x3140,
Z[
4512x2376,
]
4272x2376,
4096x2160, 2048x1080
2048x1080 930 KB
qr
5952x2532,
Z[
4512x1920
2048x872 820 KB
3840x2160, 1920x1080 1920x1080 880 KB
Taking Photos
126
NOTES
NOTES
Each folder can contain up to 500 files. When that number is exceeded, a new folder is created automatically.
Understanding folder names
An example folder name is “101_1103”. The first 3 digits indicate the folder number (from 100 to 999) and
the last 4 digits indicate the month and day when the folder was created. In the example, the folder
numbered 101 was created on November 3.
Understanding photo numbers
An example photo number is “101-0107”. The first 3 digits indicate the folder number where the photo is
stored and the last 4 digits indicate the consecutive number assigned to the photo (from 0001 to 9999).
The photo number also indicates the name and location of the file on the SD card. For example, a photo
numbered 101-0107 that was recorded on November 3, is located in the “DCIM\101_1103” folder as the
file “IMG_0107.JPG”.
4
127
Customization
Assignable Buttons and Customizable USER Screen
The camera offers a number of physical buttons to which you can assign various functions (assignable buttons).
Additionally, the control display offers the USER screen that you can customize by assigning various functions to
each of the 6 screen buttons. Assign often-used functions to the buttons/screen buttons you find most
convenient, to personalize the camera to your needs and preferences.
You can find 5 assignable buttons on the camera’s body. The following optional accessories offer additional
assignable buttons that can be used when the accessory is attached to the camera: EVF-V70 OLED Electronic
Viewfinder – 4 assignable buttons, SG-1 Shoulder Style Grip Unit – 1 assignable button, RC-V100 Remote
Controller – 4 assignable buttons. In most cases, the names of the buttons printed on the camera and optional
accessories also indicate their default settings.
Changing the Assigned Function and Using an Assignable Button
1 Press the MENU button and, while holding it pressed down, press the assignable button whose
function you wish to change.
A list of available functions appears with the current function assigned to the button highlighted.
You can also open the submenu corresponding to the button whose function you wish to change under
[System Setup] (
B
) > [Assignable Buttons] > [Camera], [EVF-V70], [Grip SG-1] or
[Remote RC-V100].
Assignable Buttons and Customizable USER Screen
128
2 Select the desired function and then press SET.
The selected function will be assigned to the selected button.
If you selected one of the preset functions, the rest of the procedure is not necessary. If you selected [User
Setting], the menu’s title bar will change to blue to indicate you are selecting a menu setting to register.
Continue the procedure to register a menu setting.
3 Navigate the menus to find the menu setting you want to register and then press SET.
The selected menu setting will be assigned to the selected button. User-selected settings will be indicated
with a
¥
in the assignable buttons’ submenu.
4 Close the menu and press the assignable button to use the assigned function.
NOTES
Depending of the function assigned, when you press an assignable button, the monitoring menu may open on
the monitoring screen with a submenu already selected. In such case, select the desired option and then
press SET.
You can reset only the functions assigned to the assignable buttons, without affecting other camera settings,
with the [System Setup] >[Reset] > [Assignable Buttons] function. All the assignable buttons will
return to their default functions.
Assignable Functions
Refer to the following table for assignable functions. During playback mode, only the assignable buttons on the
optional viewfinder or optional RC-V100 Remote Controller can be used and they can be set to different
functions from those assigned in shooting mode.
Function name Description A
[(NONE)] No function assigned – the button is disabled.
Zq
[One-Shot AF] The camera focuses automatically one time only (one-shot AF function). 92
Zq
[AF Lock] Locks the focus during continuous AF or AF-boosted MF mode. 95
Zq
[Face AF] Toggles the [Face AF] setting between [Face Priority] and [Face Only].
96
Zq
[Face Detection] Turns the face detection function on/off.
Zq
[Tracking] Turns the tracking function on/off. 97
Zq
[Focus Guide] Turns the Dual Pixel Focus Guide function on/off. 90
[Peaking] Turns peaking on/off.
91
[Peaking: VIDEO],
[Peaking: MON.+HDMI]
Turns peaking on/off on the optional viewfinder (VIDEO) or on all external monitors connected to
the MON. terminals or HDMI OUT terminal, respectively.
[Magnification] Turns magnification on/off.
92
[Magn.: VIDEO],
[Magn.: MON.+HDMI]
Turns the magnification on/off on the optional viewfinder (VIDEO) or on all external monitors
connected to the MON. terminals or HDMI OUT terminal, respectively.
[Push Auto Iris]
1
The camera automatically adjusts the aperture only while the button is held pressed down. 81
[Iris Mode]
1
Switches the aperture adjustment mode between automatic and manual. 79
[Iris +]
1
, [Iris –]
1
Opens up/closes the aperture, respectively. 80
[ND +], [ND –]
Cycles through ND filter settings in increasing/decreasing (higher/lower density) order,
respectively.
78
[AE Shift +]
1
, [AE Shift –]
1
Compensates the exposure making the image brighter/darker, respectively. 82
[Backlight], [Spotlight] Toggles the light metering mode between [Standard] and [Backlight]/[Spotlight], respectively. 82
[Zebra] Turns zebra patterns on/off.
99
[Zebra: VIDEO],
[Zebra: MON.+HDMI]
Turns the zebra patterns on/off on the optional viewfinder (VIDEO) or on all external monitors
connected to the MON. terminals or HDMI OUT terminal, respectively.
129
Assignable Buttons and Customizable USER Screen
[False Color] Turns the false color display on/off.
100
[False Color: VIDEO],
[False Color: MON.+HDMI]
Turns the false color display on/off on the optional viewfinder (VIDEO) or on all external
monitors connected to the MON. terminals or HDMI OUT terminal, respectively.
[False Color: MON.1],
[False Color: MON.2],
[False Color: HDMI]
Turns the false color display on/off on an individual external monitor connected to the
respective terminal.
[False Color Index] Displays/hides the false color index on the monitoring screen.
[Waveform Monitor]
2
Turns the waveform monitor on/off.
115
[WFM: VIDEO]
2
,
[WFM: MON.+HDMI]
2
Turns the waveform monitor’s on/off on the optional viewfinder (VIDEO) or on all external
monitors connected to the MON. terminals or HDMI OUT terminal, respectively.
[LUT] Turns on/off the application of the selected LUT to all monitoring devices.
155
[LUT: VIDEO], [LUT: MON.1],
[LUT: MON.2], [LUT: HDMI]
Turns on/off the application of the selected LUT to the optional viewfinder (VIDEO) or the
individual external monitor connected to the respective terminal.
[LUT: SDI OUT 1/2/3/4],
[LUT: SDI OUT 1/2],
[LUT: SDI OUT 3/4]
Turns on/off the application of the selected LUT to video output from all the SDI OUT terminals,
to video output only from the SDI OUT 1 and SDI OUT 2 terminals, or to video output only from
the SDI OUT 3 and SDI OUT 4 terminals, respectively.
[Set White Balance] Starts the white balance calibration for a custom white balance setting. 87
[AWB Lock] While using auto white balance (AWB), locks the current white balance settings. 87
[ AWB], [Å Set A],
[Å Set B], [¼ Daylight],
[É Tungsten],
[
USER_01] to
[
USER_05]
Changes the white balance mode/setting to the respective option.
86
[Control Display Setup]
2
Opens the monitoring menu’s [Control Display] submenu (setup of the camera’s control display
or the control display on an optional OU-700 Remote Operation Unit connected to the camera).
31
[Control Display]
2
Turn the camera’s control display on/off.
[EVF-V70 Setup]
2, 3, 4
Opens the monitoring menu’s [EVF-V70] submenu (setup of the optional viewfinder). 42
[OSD Output]
2
Turns on/off the camera’s onscreen displays on/off.
154
[OSD Output: VIDEO]
2
,
[OSD Output: MON.+HDMI]
2
Turns on/off the camera’s onscreen displays on the optional viewfinder (VIDEO) or on all
external monitors connected to the MON. terminals or HDMI OUT terminal, respectively.
[Markers] Turns onscreen markers on/off.
98
[Markers: VIDEO],
[Markers: MON.+HDMI]
Turns onscreen markers on/off on the optional viewfinder (VIDEO) or on all external monitors
connected to the MON. terminals or HDMI OUT terminal, respectively.
[Anamorphic] Turns the anamorphic desqueeze on/off.
122
[Anamorphic: VIDEO],
[Anamorphic: MON.+HDMI]
Turns on/off the application of the anamorphic desqueeze on the optional viewfinder (VIDEO) or
on all external monitors connected to the MON. terminals or HDMI OUT terminal, respectively.
[Color Bars] Turns color bars on/off. 114
[Photo] Records a photo. 125
[Time Code]
3, 4
Displays the monitoring menu’s [Time Code] submenu. 101
[Time Code Hold]
2
Puts the time code display on hold or resumes it. 102
[Add $ Mark]
2
Adds an
$
mark to the clip.
146
[Add % Mark]
2
Adds a
%
mark to the clip.
[Headphones +]
2
,
[Headphones –]
2
Increases/reduces the headphone volume, respectively. 113,
143
[Monitor Channels]
2
Switches the audio output channel. 160
[Audio Lvl Indicator]
2
Displays/hides the audio level meter on the monitoring screen. 111
[FUNC]
3, 4
Enters the direct setting mode, replicating the function of the optional viewfinder’s FUNC
button.
73
[Slow&Fast Frame Rate]
3, 4
When slow & fast motion recording is activated, enters the direct setting mode with the
shooting frame rate underlined and ready to be adjusted.
68
Function name Description A
Assignable Buttons and Customizable USER Screen
130
1
This function cannot be assigned to the optional SG-1 Shoulder Style Grip Unit.
2
This function can be used also in playback mode (assignable buttons only).
3
This function opens the monitoring menu or can only be operated from that menu.
4
This function is not available for the USER screen.
Customizing and Using the USER Screen
In addition to the USER screen that can be used with the camera’s control display, the optional OU-700 Remote
Operation Unit offers an additional USER screen that can be customized and used separately from that of the
camera. You can customize three screens’ worth of USER buttons on the camera.
1 Press the USER button and then press SET.
Screen buttons not yet assigned will appear as [(NONE)]. The
first available screen button position will be highlighted with
an orange selection frame.
After pressing the USER button, you can press the USER
button repeatedly or turn the SELECT dial to cycle through
the USER screens and select the desired one.
2 Turn the SELECT dial to select the screen button you wish
to assign or edit and then press SET.
A list of available functions appears with the current function
assigned to the screen button highlighted.
The functions that can be assigned are mostly the same as
for assignable buttons (A 128).
3 Select the desired function and then press SET.
The selected function will be assigned to the selected screen
button.
4 Whenever necessary, press the USER button to open the
desired USER screen and press the desired screen button
to use the functions you customized.
[Shutter]
3, 4
Enters the direct setting mode with the shutter speed underlined and ready to be adjusted. 75
[ISO/Gain]
3, 4
Enters the direct setting mode with the ISO speed or gain value underlined and ready to be
adjusted.
77
[White Balance]
3, 4
Enters the direct setting mode with the white balance underlined and ready to be adjusted. 86
[Custom Picture]
3, 4
Opens the monitoring menu’s [Custom Picture] (
/
) submenu. 131
[My Menu]
Opens the [My Menu] customized submenu. (The [My Menu] screen in the monitoring menu
when using an assignable button; the [My Menu] screen in the camera menu when using a
screen button in the USER screen.)
35
[Initialize Media]
2,
3
Opens the monitoring menu’s [Initialize Media] submenu. 51
[¥ User Setting]
3, 4
Customizable slot. Assign to the button any monitoring menu setting you would like to register.
Function name Description A
131
Custom Picture Settings
Custom Picture Settings
The camera lets you change many settings (A 134) that control various aspects of the image produced. As a
set, all these settings are treated as a single custom picture file. After adjusting the desired settings to your
preference, you can save up to 20 custom picture files (in the camera or on an SD card), and load them later to
apply exactly the same settings (A 133). You can also save the custom picture file as part of the metadata
recorded with XF-AVC clips (A 133).
Custom picture settings have no effect during RAW video recording/output.
NOTES
Custom picture files are exclusively compatible for use only with C700 / C700 PL / C700 GS PL / C700 FF /
C700 FF PL cameras.
Selecting Custom Picture Files
Select a custom picture file to apply its settings to your recordings or to edit, rename, protect, or transfer it.
1 Open the custom picture file’s selection screen.
HOME screen: [COLOR] > [CP OTHERS] > [File] > [Select]
Monitoring menu: [Custom Picture] (
/
) > [File] > [Select]
2 Turn the SELECT dial to select the desired file and then press [OK] (HOME screen) or press SET
(monitoring menu).
Select one of the custom picture files saved in the camera (C1 to C20). To use the settings of a custom
picture file saved on an SD card, copy the file to the camera in advance (A 133).
When you close the menu, the selected custom picture file’s settings will be applied. The [Gamma] and
[Color Space] settings currently in use are displayed under [COLOR] in the HOME screen and their icons will
appear at the left of the monitoring screen.
If editing of the custom picture file’s detailed settings ([Other Settings] > [Activate]) was enabled (A 131),
will appear at the left of the monitoring screen.
NOTES
About changing custom picture related settings using the optional RC-V100 Remote Controller
- When an optional RC-V100 Remote Controller is connected to the camera, you can press the remote
controller’s CUSTOM PICT. button to open the monitoring menu’s [Custom Picture] (
/
) submenu.
- If a protected custom picture file is selected on the camera, custom picture related settings cannot be
changed using the remote controller.
- Adjusting custom picture related settings using the remote controller will change the settings registered
under the currently selected custom picture file. If you want to keep an important custom picture file, copy it
in advance to an SD card or select in advance a custom picture file you do not mind changing.
Editing a Custom Picture File’s Detailed Settings
1 Turn off the preset color settings.
HOME screen: [COLOR] > [CP MAIN] > [Preset] > [Off]
Monitoring menu: [Custom Picture] (
/
) > [Preset] > [Off]
2 If necessary, change the gamma curve, color space and/or color matrix (A 134).
HOME screen: From the same submenu select [Gamma]/[Color Space]/[Color Matrix]; select the desired
setting and then press SET.
Custom Picture Settings
132
Monitoring menu: Select [Main Settings] > [Gamma] /[Color Space]/[Color Matrix]; select the desired setting
and then press SET.
3 Press the BACK button.
4 Enable the editing of the custom picture file’s detailed settings.
HOME screen: [CP OTHERS] > [Other Settings] > [Activate] > [On]
Monitoring menu: [Other Settings] > [Activate] > [On]
5 From the same submenu select a detailed setting you wish to adjust and then press SET.
6 Change the setting to the desired level and then press SET.
Refer to
Available Custom Picture Settings
(A 134) for details on the various settings.
Repeat steps 5 and 6 for other settings, as necessary.
When you close the menu, the new custom picture settings will be applied.
Resetting Custom Picture Files
1 Select a custom picture file (A 131).
2 Open the [Reset] submenu.
HOME screen: [COLOR] > [CP OTHERS] > [File] > [Reset]
Monitoring menu: [Custom Picture] (
/
) > [File] > [Reset]
3 Press both [RESET] buttons simultaneously (HOME screen) or select [OK] and then press SET
(monitoring menu).
Renaming Custom Picture Files
1 Select a custom picture file (A 131).
2 Open the [Rename] submenu.
HOME screen: [COLOR] > [CP OTHERS] > [File] > [Rename]
Monitoring menu: [Custom Picture] (
/
) > [File] > [Rename] > [Input]
3 Enter the desired file name (up to 8 characters) using the keyboard screen (
A
37).
Protecting Custom Picture Files
Protecting a custom picture file prevents its settings from being accidentally changed.
1 Select a custom picture file (A 131).
2 Open the [Protect] submenu.
HOME screen: [COLOR] > [CP OTHERS] > [File] > [Protect]
Monitoring menu: [Custom Picture] (
/
) > [File] > [Protect]
3 Select [Protect] and then press SET.
i
will appear next to the file name.
To remove the protection settings, select [Unprotect] instead.
133
Custom Picture Settings
Copying Custom Picture Files
You can transfer custom picture files between the camera and SD card.
Copying a File from the Camera to an SD Card
1 Select a custom picture file (A 131).
2 Open the [Copy to
8
] submenu.
HOME screen: [COLOR] > [CP OTHERS] > [File] > [Transfer] > [Copy to 8]
Monitoring menu: [Custom Picture] (
/
) > [File] > [Transfer] > [Copy to
8
]
3 Select the destination file and then press [OK] (HOME screen) or press SET (monitoring menu).
Select an existing custom picture file to overwrite it or [New File] to save the settings as a new custom
picture file on the SD card.
4 Press both [COPY] buttons simultaneously (HOME screen) or select [OK] and then press SET (monitoring
menu).
The file on the SD card will be overwritten or a new file will be created on the SD card.
5 When the confirmation message appears, press [OK] (HOME screen) or press SET (monitoring menu).
Replacing a File in the Camera with a File on an SD Card
1 Select the custom picture file that you wish to replace (A 131).
2 Open the [Load from
8
] submenu.
HOME screen: [COLOR] > [CP OTHERS] > [File] > [Transfer] > [Load from 8]
Monitoring menu: [Custom Picture] (
/
) > [File] > [Transfer] > [Load from
8
]
3 Select the file with the settings that you want to replicate and then press [OK] (HOME screen) or press SET
(monitoring menu).
4 Press both [LOAD] buttons simultaneously (HOME screen) or select [OK] and then press SET (monitoring
menu).
The file in the camera will be overwritten by the one on the SD card.
5 When the confirmation message appears, press [OK] (HOME screen) or press SET (monitoring menu).
NOTES
You can also copy to the camera a custom picture file embedded in a clip (A 148).
Embedding Custom Picture Settings in a Clip
When you record an XF-AVC clip using custom picture settings, you can have the custom picture file embedded
in the metadata and saved along with the clip. Later, you can copy the custom picture file embedded in the clip
to the camera (A 148) and use the same custom picture settings to record additional clips.
1 Open the [Add
/
File] submenu.
[Rec/Media Setup] (
3
) > [Metadata] > [Add
/
File]
2 Select [On] and then press SET.
Custom Picture Settings
134
Available Custom Picture Settings
Preset and Main Settings
Submenu levels / Menu items Options / Additional information
[Preset] [Canon Log 3 : C.Gamut], [Canon Log 3 : BT.2020], [Canon Log 3 : DCI-P3], [Canon Log 3 : BT.709],
[Canon Log 2 : C.Gamut], [Canon Log 2 : BT.2020], [Canon Log 2 : DCI-P3], [Canon Log 2 : BT.709],
[Canon Log], [BT.2020], [BT.709], [Off]
The camera offers a number of preset color settings (combinations of color space, gamma curve and
color matrix). For details, refer to
Preset Color Settings
(A 84).
[Off]: Select this setting when you want to set a different combination of custom picture settings with
the individual custom picture settings described below.
[Main Settings]
[Gamma] [Canon Log 3], [Canon Log 2], [Canon Log], [Wide DR], [Normal 1 (Standard)], [Normal 2 (x4.0)],
[Normal 3 (BT.709)], [Normal 4 (x5.0)]
Changes the overall look of the image.
[Canon Log 3]: Logarithmic gamma curve that keeps the characteristics of the [Canon Log] setting
while expanding its dynamic range. Requires image processing in post-production.
[Canon Log 2]: Logarithmic gamma curve that obtains a richer color gradation in the dark areas of
the image. Requires image processing in post-production.
[Canon Log]: Logarithmic gamma curve that obtains an impressive dynamic range. Requires image
processing in post-production.
[Wide DR]: Gamma curve with a very wide dynamic range. Optimized for playback on TV monitors.
[Normal 1 (Standard)]: Standard picture for playback on TV monitors.
[Normal 2 (x4.0)]: Setting suitable for playback on TV monitors. Produces brighter highlights (bright
areas of the image) than with the [Normal 1 (Standard)] setting.
[Normal 3 (BT.709)]: Setting suitable for playback on TV monitors. Produces a more faithful black
gradation in the shadows (dark areas of the image) than with the [Normal 2 (x4.0)] setting.
[Normal 4 (x5.0)]: Setting suitable for playback on TV monitors. Produces even better black gradation
in the shadows (dark areas of the image) than with the [Normal 3 (BT.709)] setting.
[Color Space] [Cinema Gamut], [BT.2020 Gamut], [DCI-P3 Gamut], [BT.709 Gamut]
Determines the color space of the image.
[Cinema Gamut]: Color space developed by Canon based on the specific characteristics of the
camera’s imaging sensor. It covers a wider color gamut than that of BT.2020. Use this setting
with workflows that require ACES2065-1 color space.
[BT.2020 Gamut]: Color space that meets ITU-R BT.2020 standards, which defines parameters for
ultra-high-definition television (4K/8K).
[DCI-P3 Gamut]: Color space that meets the guidelines established by DCI (Digital Cinema Initiatives).
[BT.709 Gamut]: Standard color space that is compatible with sRGB specifications.
Input
Output
Input
Output
Input
Output
Normal 2/3/4
Normal 1
Normal 4
Normal 3
Normal 1/2
Normal 1
Wide DR
Canon Log
Normal 1
Canon Log
Canon Log 2
Canon Log 3
Visual range
BT.709
DCI-P3
Cinema Gamut
BT.2020
135
Custom Picture Settings
Other Settings
[Color Matrix] [Neutral], [Production Camera], [Cinema EOS Original], [Video], [Off]
The color matrix affects the overall color tonality of the image.
[Neutral]: Reproduces neutral colors.
[Production Camera]: Reproduces colors more suitable for motion picture production.
[Cinema EOS Original]: Color matrix developed by Canon, designed to reproduce the 4K output of an
EOS C500 camera using the BT.709 color space.
[Video]: Reproduces the colors of an EOS C300/EOS C500 camera with no custom picture settings
applied.
[Off]: Colors are not adjusted.
Submenu levels / Menu items Options / Additional information
[Other Settings]
[Activate] [On], [Off]
Set this setting to [On] to enable the editing of the custom picture’s detailed settings explained in this
table.
[Black]
[Master Pedestal] –50 to 50 (±0)
Increases or decreases the black level. Higher settings will make dark areas brighter but decrease
contrast. When [Gamma] is set to one of the Canon Log settings, this setting has no effect on the
picture.
[Master Black Red],
[Master Black Green],
[Master Black Blue]
–50 to 50 (±0)
These settings correct the color cast in blacks. When [Gamma] is set to one of the Canon Log
settings, these settings have no effect on the picture.
[Black Gamma]
[Level] –50 to 50 (±0)
[Range], [Point] –20 to 50 (±0)
These settings control the lower part of the gamma curve (dark areas of the image). When [Gamma]
is set to one of the Canon Log settings or [Wide DR], these settings have no effect on the picture.
[Level]: Raises or lowers the lower part of the gamma curve.
[Range]: Selects the adjustment range from the selected [Point].
[Point]: Determines the shape of the lower part of the gamma curve.
[Low Key Satur.]
[Activate] [On], [Off]
Set this setting to [On] to enable the adjustment of color saturation in dark areas with the [Level]
setting.
[Level] –50 to 50 (±0)
Specifies how saturated colors are in dark areas.
[Knee]
[Activate] [On], [Off]
Set this setting to [On] to enable the adjustment of the knee point with the following settings.
Submenu levels / Menu items Options / Additional information
Input
Output
[Point]
[Range]
[Level]
Custom Picture Settings
136
[Slope] –35 to 50 (±0)
[Point] 50 to 109 (95)
[Saturation] –10 to 10 (±0)
These settings control the upper part of the gamma curve (highlights of the image). By compressing
the highlights, you can prevent parts of the image from being overexposed. When [Gamma] is set to
one of the Canon Log settings or [Wide DR], these settings have no effect on the picture.
[Slope]: Determines the slope of the gamma curve above the knee point.
[Point]: Sets the knee point of the gamma curve.
[Saturation]: Adjusts the color saturation in the highlights.
[Sharpness]
[Level] –10 to 50 (±0)
Sets the sharpness level of the video output signal and the recorded signal.
[H Detail Freq.] –8 to 8 (±0)
Sets the center frequency of horizontal sharpness. Setting higher values increases the frequency,
which, in turn, increases the sharpness.
[Coring Level] –30 to 50 (±0)
Sets the level of correction of artifacts caused by high sharpness levels (coring). Higher values
prevent sharpness from being applied to minute details, resulting in less noise.
[Coring D-Ofst] 0 to 50 (0)
Sets the coring level of the minimum brightness level (level-dependent offset).
[Coring D-Curve] 0 to 8 (0)
Sets the curve of coring adjustment, in other words, how the coring level changes from the value set
for [Coring Level] to that set for [Coring D-Ofst] (level-dependent curve).
[HV Detail Bal.] –8 to 8 (±0)
Adjusts the ratio between horizontal and vertical detail. Higher values emphasize vertical detail while
lower values emphasize horizontal detail.
[Limit] –50 to 50 (±0)
Restricts how much sharpness is applied.
[Select] 0 to 15 (0)
In addition to the sharpness set by [Level], [Select] sets the sharpness for areas with higher
frequencies. Higher values apply more sharpness to areas with higher frequencies. Use this for
subjects in which normal sharpening is not effective.
[Knee Aperture Gain] 0 to 9 (0)
[Knee Aperture Slope] 0 (no slope), 1 (steep slope) to 3 (gradual slope) (1)
These settings allow you to adjust the sharpness of only the areas above the knee point. When
[Gamma] is set to one of the Canon Log settings or [Wide DR], these settings have no effect on the
picture.
[Knee Aperture Gain]: Determines the amount of sharpness.
[Knee Aperture Slope]: Sets the slope of the sharpness.
[Level Depend Level] 0 to 50 (0)
Sets the brightness of the dark areas of the image that will be affected.
Submenu levels / Menu items Options / Additional information
Input
OutputOutput
Input
[Slope]
[Point]
137
Custom Picture Settings
[Level Depend Slope] 0 (no slope), 1 (steep slope) to 3 (gradual slope) (0)
Determines the slope of the area between the upper and lower parts of the gamma curve.
[Level Depend Offset] 0 to 50 (0)
Adjusts the sharpness level of dark areas in the image. Setting higher values will lower the sharpness
level.
[Noise Reduction] –1 (noise reduction not applied), [Off], 1 (lowest level) to 12 (highest level)
Reduces the amount of noise that appears in the image.
Even when this setting is set to [Off], a very low level of NR filter is applied. Select [–1] to
completely turn off the NR filter.
[Skin Detail]
[Effect Level] [High], [Middle], [Low], [Off]
[Hue] –16 to 16 (±0)
[Chroma], [Area], [Y Level] 0 to 31 (16)
The camera applies a softening filter to areas in the picture with skin tones to give a more pleasant
appearance. By changing these settings, you can determine what areas will be detected as skin
tones. A zebra pattern will appear on the monitoring screen over areas of the image that are detected
as having skin tones.
[Effect Level]: Adjusts the level of the filter.
[Hue]: Adjusts the hue for detection of skin tones.
[Chroma]: Adjusts the color saturation for detection of skin tones.
[Area]: Adjusts the color range for detection of skin tones.
[Y Level]: Adjusts the brightness for detection of skin tones.
[Selective NR]
[Effect Level] [High], [Middle], [Low], [Off]
[Hue] 0 to 31 (0)
[Chroma], [Area],
[Y Level]
0 to 31 (16)
The camera detects the characteristics of a certain color or tone and applies a noise reduction filter
to the targeted areas. A zebra pattern will appear on the monitoring screen over areas targeted for
noise reduction.
[Effect Level]: Adjusts the level of the noise reduction filter.
[Hue]: Adjusts the hue for the color to be detected.
[Chroma]: Adjusts the color saturation for the color to be detected.
[Area]: Adjusts the color range for the color to be detected.
[Y Level]: Adjusts the brightness for the color to be detected.
[Color Matrix Tuning]
[Gain] –50 to 50 (±0)
[Phase] –18 to 18 (±0)
These settings adjust the color intensity ([Gain]) and color phase ([Phase]) of the color matrix,
affecting the color tones of the whole image.
[R-G], [R-B], [G-R], [G-B],
[B-R], [B-G]
–50 to 50 (±0)
Each matrix changes the tint of the picture along the color gradations detailed below, affecting the
color tones of the whole image.
[R-G]: cyan/green and red/magenta; [R-B]: cyan/blue and red/yellow;
[G-R]: magenta/red and green/cyan; [G-B]: magenta/blue and green/yellow;
[B-R]: yellow/red and blue/cyan; [B-G]: yellow/green and blue/magenta.
[White Balance]
[R Gain], [B Gain] –50 to 50 (±0)
These settings adjust the amount of white balance throughout the whole image by changing the
intensity of red tones ([R gain]) and blue tones ([B Gain]).
Submenu levels / Menu items Options / Additional information
Custom Picture Settings
138
NOTES
If editing of the custom picture file’s detailed settings is enabled ([Other Settings] > [Activate] is set to [On]),
when an optional RC-V100 Remote Controller is connected to the camera, the following custom picture
settings can be changed using the buttons and dials on the remote controller.
- [Other Settings] > [Black] > [Master Pedestal], [Master Black Red], [Master Black Blue]
- [Other Settings] > [Black Gamma] > [Level]
- [Other Settings] > [Knee] > [Slope], [Point] (only when [Knee] > [Activate] is set to [On])
- [Other Settings] > [Sharpness] > [Level]
- [Other Settings] > [White Balance] > [R Gain], [B Gain]
[Color Correction]
[Select Area] [Area A&B], [Area B], [Area A], [Off]
The camera detects areas with certain color characteristics (color phase, chroma, area and Y level)
and corrects them when recording. You can set the color correction for up to two different areas
(A and B) and apply the color correction to either one ([Area A] or [Area B]) or both of them ([Area
A&B]). While color correction is activated, a zebra pattern will appear on the monitoring screen over
areas of the image detected as having the characteristics specified for area A or area B.
[Area A Setting Phase],
[Area B Setting Phase]
0 to 31 (0)
These settings determine the color phase of the area to be corrected (A or B, respectively).
[Area A Setting Chroma],
[Area A Setting Area],
[Area A Setting Y Level],
[Area B Setting Chroma],
[Area B Setting Area],
[Area B Setting Y Level]
0 to 31 (16)
These settings determine the following color characteristics of the area to be corrected (A or B,
respectively).
[Area A Setting Chroma], [Area B Setting Chroma]: Color saturation.
[Area A Setting Area], [Area B Setting Area]: Color range.
[Area A Setting Y Level], [Area B Setting Y Level]: Brightness.
[Area A Revision Level],
[Area B Revision Level]
–50 to 50 (±0)
These settings adjust the amount of correction applied to the color saturation in the corrected area
(A or B, respectively).
[Area A Revision Phase],
[Area B Revision Phase]
–18 to 18 (±0)
These settings adjust the amount of correction applied to the color phase in the corrected area
(A or B, respectively).
[Other Functions]
[Setup Level] –50 to 50 (±0)
Adjusts the black level set by the [Black] > [Master Pedestal] setting. When [Gamma] is set to one
of the Canon Log settings, this setting has no effect on the picture.
[Over 100%] [Through], [Press], [Clip]
Determines how the camera handles video signals exceeding 100%.
[Through]: Leave the signal unchanged.
[Clip]: Clip the signal at 100%.
[Press]: Compress a signal of up to 108% down to 100% levels.
Submenu levels / Menu items Options / Additional information
139
Customizing Onscreen Displays
Customizing Onscreen Displays
You can use the [Custom Display 1] or [Custom Display 2] settings to customize the onscreen displays that
appear on the monitoring in shooting mode and the [Custom Display] settings to customize the onscreen
displays that appear during playback. For details on which onscreen displays can be customized, refer to
Onscreen Displays on the Shooting Screen
(A 59) and
Onscreen Displays During Playback
(A 144).
1 Open the desired customized displays submenu.
Camera menu: [Monitoring Setup] > [Custom Display 1] or [Custom Display 2] or
> [Monitoring Setup] > [Custom Display]
Monitoring menu: [Monitoring Setup] (¢) > [Custom Display 1] or [Custom Display 2] (shooting
mode), or [Custom Display] (playback mode)
2 Select the desired onscreen display.
3 Select the desired option and then press SET.
Saving and Loading Camera Settings
140
Saving and Loading Camera Settings
After you adjust settings in the various menus and setup screens, you can save those settings in the camera or
on an SD card. You can load those settings at a later date between C700 / C700 PL / C700 GS PL cameras or
between C700 FF / C700 FF PL cameras so that you can use the cameras in the exact same way.
Saving Camera Settings
1 Open the [Save] submenu.
[System Setup] (
B
) > [Transfer Menu/
/
] > [Save]
2 Select [To Camera] or [To
8
] and then press SET.
3 Press both [SAVE] buttons simultaneously (camera menu) or select [OK] and press SET (monitoring
menu).
The camera’s settings will be saved to the selected destination. If settings were previously saved, the old file
will be overwritten by the current menu settings.
4 When the confirmation message appears, press [OK] (camera menu) or press SET (monitoring
menu).
Loading Camera Settings
1 Open the [Load] submenu.
[System Setup] (
B
) > [Transfer Menu/
/
] > [Load]
2 Select [From Camera] or [From
8
] and then press SET.
3 Press both [LOAD] buttons simultaneously (camera menu) or select [OK] and press SET (monitoring
menu).
The camera’s settings will be replaced by the settings saved on the selected source. Then, the screen will
turn black momentarily and the camera will restart.
NOTES
The following settings are not saved with this operation.
- The following settings in the HOME screen: aperture value and ND filter setting ([IRIS]), shutter speed
([SHUTTER]), ISO speed and gain value ([ISO/GAIN]) and white balance mode and adjustment settings
([WB]) except for the user-set white balance settings, which are saved.
- Passwords/encryption keys for the various settings that were changed by the user under the
[NETWORK] submenus. (Default passwords are saved.)
When settings are loaded with this operation, even protected custom picture files in the camera will be
replaced.
The camera settings file saved on the camera will be deleted if you reset the camera using the
[System Setup] > [Reset] > [All Settings] option.
Camera settings files are exclusively compatible for use only between C700 / C700 PL / C700 GS PL cameras
or between C700 FF / C700 FF PL cameras. If a C700 FF / C700 FF PL camera loads camera settings saved
with a C700 / C700 PL / C700 GS PL, some settings will be reset to default. Camera settings saved with a
camera using a newer firmware version may not be able to be loaded with a camera using an older firmware
version.
5
141
Playback
Playback
This section explains how to play back clips and photos with the camera. For details on playing back clips
recorded on the CDX-36150’s Capture Drive, refer to
Playing Back Recordings from the Capture Drive
(A 211).
For details on playing back clips using an external monitor, refer to
Connecting to an External Monitor or
Recorder
(A 152).
The PLAY (Playback Control) Screen
Press the PLAY button to switch the camera to playback mode.
The PLAY screen will appear on the camera’s control display showing the information of the last clip recorded in
the camera’s main recording format. The camera will enter playback pause mode (
Ý
will appear on the PLAY
screen and
Ý
PAUSE will appear on top of the monitoring screen).
Pressing the HOME, USER, ALT or TC buttons will switch the camera back to shooting mode and open the
respective setup screen on the control display.
To change the camera’s system frequency
The camera cannot play back recording media that were recorded using a system frequency different from that
of the camera. To play back such recording media, change the camera’s system frequency.
1 Open the [System Frequency] submenu in playback mode.
[Rec/Media Setup] > [System Frequency]
2 Select the system frequency that matches the recordings on the media you wish to play back.
16
12
13
14
15
4
5
6
3
2
1
8
9
7
17
11
10
Playback
142
Selecting the Recording Media and Format to Play Back
When the camera first switches to playback mode, the media and format selected for the main recording will
also be selected for playback. Perform the following procedure to select a different type of recordings or
recordings from a different media.
From the PLAY screen:
1 Press [PB MEDIA].
You can also press [PB MEDIA] while the list of clips is displayed.
2 Select the desired option and then press SET.
If you selected one of the CFast card options: To switch between the CFast cards, press the SLOT SEL.
button.
Playing Back Clips
After selecting the format and recording media of the clips you wish to play back, select the desired clip from the
list of clips recorded on the selected recording media to play it back.
From the PLAY screen:
1 Press [CLIP LIST] to open the clip list.
2 Turn the SELECT dial to select the desired clip.
3 Press SET to return to the PLAY screen and start playback.
Playback will start and the video will appear on the monitoring screen (
Ð
will appear on the PLAY screen
and
Ð
PLAY will appear on top of the monitoring screen). When the last frame of clip is reached, playback
will pause automatically.
Press SET during playback to pause. Press SET again during playback pause to resume the playback.
During playback pause you can turn the SELECT dial to change the playback position. Press [STEP SIZE] to
change the interval used when you turn the SELECT dial.
1 [PB MEDIA] (playback media): Press the screen
button to select the media and format selected
for playback (A 142).
2 Media/format selected for playback
3 Playback operation:
Ý
– pause,
Ð
– play,
Ô
/
Ó
- frame reverse/advance.
4 Time code of the current playback position
5 Playback progress bar
6Start time code
7 Press SET to start/pause the playback.
In playback pause, turn the SELECT dial to
advance/reverse the playback position (A 142).
8[STEP SIZE]: Interval size used to advance/
reverse the playback position.
Press the screen button repeatedly to change the
interval between 1 frame, 1 second or 10% of the
clip’s duration.
9 [OPTIONS]: Press the screen button to open the
clip operations (or photo operations) menu
(A 145).
10 Recording media selected for playback
CFast card (the one currently selected
appears in white). Press the SLOT SEL.
button to switch to the other CFast card.
8
SD card
11 Clip file name (A 62)
12 End time code
13 Clip duration
14
$
mark*/
%
mark* (A 117, 146)
15 Embedded custom picture file* (A 133)
16 Clip number / Total number of clips
17 [CLIP LIST]: Press the screen button to open the
list of clips in the recording media to select
another clip.
* Only for XF-AVC clips.
143
Playback
IMPORTANT
Observe the following precautions while an access indicator is illuminated in red. Failure to do so may result in
permanent data loss.
- Do not remove the power source or turn off the camera.
- Do not open the card slot cover of the card being accessed and do not remove the card.
Adjusting the Volume
You can connect headphones to the
×
(headphone) terminal to listen to the audio during playback. Adjust the
headphone volume with the [Audio Setup] > [Headphone Volume] setting. If you set an
assignable button to [Headphones +] or [Headphones –] (A 127), you can press the button to adjust the
headphone volume without using the menu.
The audio signal will also be output from the SDI OUT terminals, MON. terminals and HDMI OUT terminal.
NOTES
For details on changing the audio channel, refer to
Audio Output
(A 160).
Viewing Photos
After selecting photos as the format to play back, use the SELECT dial to
browse through your photos.
From the PLAY screen:
1 Select [SD Card (Photos)] as the media/format to play back
(A 142).
The last recorded photo on the SD card will appear on the
monitoring screen and the details of the image file will appear on the
PLAY screen (the file name will be highlighted with an orange frame).
2 Turn the SELECT dial to display other photos.
IMPORTANT
Observe the following precautions while the SD card access indicator is illuminated in red. Failure to do so may
result in permanent data loss.
- Do not remove the power source or turn off the camera.
- Do not remove the SD card.
NOTES
The following photos may not be displayed correctly.
- Photos not recorded with this camera.
- Image files that were created, edited or renamed using a computer.
Playback
144
Onscreen Displays During Playback
If the output of onscreen displays is activated for the terminal used (A 154), the following onscreen displays will
appear on the monitoring screen during playback, along with the playback image.
1
For XF-AVC clips recorded using slow & fast motion recording, the shooting frame rate (S&F FPS) and playback frame rate will
both be displayed.
2
Only for XF-AVC clips.
3
You can turn these onscreen displays on and off individually with the corresponding setting in the [Monitoring
Setup] > [Custom Display] submenu.
2
1413
31 46 8
9
10
12
11
5 7
1615 17
1 Temperature warning and fan operation (A 64)
2 Recording media (CFast card, SD card, Capture
Drive)
3 Playback operation:
Ý
– pause,
Ð
– play,
Ô
/
Ó
- frame reverse/advance.
4 Frame rate
1
(A 65)
5 Embedded custom picture file
2
(A 133)
6 Relay recording
2
(A 52)
5
indicates the first part of the recording,
6
indicates the middle part(s) and
7
indicates the
last part.
7
$
mark
2
/
%
mark
2
(A 117, 146)
8Time code (A 101)
9 Camera index (A 63)
Custom display
3
: [Camera Index]
10 Clip number / Total number of clips
11 Onscreen displays output (A 154)
12 Audio level meter and audio output channel
(A 160)
Custom display
3
: [Audio Lvl Indicator]
13 User bit
2
(A 104)
14 Aperture value
2
(A 79), shutter speed
2
(A 74)
and ISO speed/gain value
2
(A 76)
Custom display
3
: [Camera Data]
15 Recording date and time
2
Custom display
3
: [Date/Time]
16 Headphones volume (only while adjusting the
volume)
17 Power supply voltage (DC IN and battery) (A 26)
The power supply currently in use is indicated
with a
Ð
mark.
145
Clip/Photo Operations
Clip/Photo Operations
Using the clip operations menu, you can perform various operations on the clip selected in the PLAY screen or
display additional information about the clip. Available options will depend on the format selected for playback.
The only operation available for photos is [Delete] (A 147) so the following table will show only the clip
operations.
Clip operations menu
* [PB MEDIA] setting.
IMPORTANT
Observe the following precautions while an access indicator is illuminated in red. Failure to do so may result in
permanent data loss.
- Do not remove the power source or turn off the camera.
- Do not open the card slot cover of the card being accessed and do not remove the card.
NOTES
To perform operations on clips/photos recorded on an SD card, make sure the LOCK switch on the SD card is
not set to prevent writing.
Displaying Clip Information
You can display detailed information about the selected clip and the custom picture settings and metadata
recorded with the clip.
1 Select the desired clip (A 142).
2 Open the clip information screen.
[OPTIONS] > [Display Clip Info]
The [Clip Info] screen will appear on the control display. Turn the SELECT dial to scroll through all the
information.
3 Press the PLAY button (or the BACK button twice) to return to the PLAY screen.
Menu item Description
[Playback Media]*
[CFast
(XF-AVC)]
[CFast
(ProRes)]
[SD Card
(XF-AVC)]
[Display Clip Info]
Displays the clip information screen on the control display
(A 145).
Ü Ü Ü
[Add
$
Mark],
[Delete
$
Mark]
Adds or deletes an
$
mark (A 146, 147). Ü
[Add
%
Mark],
[Delete
%
Mark]
Adds or deletes a
%
mark (A 146, 147). Ü
[Delete] Deletes a clip (A 147). Ü Ü Ü
[Delete User Memo] Deletes the user memo and GPS information of a clip (A 147). Ü Ü
[Copy
/
File] Copies the custom picture file from a clip to the camera (A 148). Ü Ü
[Recover Clip] Recovers data from a corrupted clip (A 53). Ü Ü Ü
[FTP Transfer] Copies a clip to the FTP server using FTP protocol (A 186). Ü
Clip/Photo Operations
146
1 Recording date and time
2 Clip file name (A 62)
3 Bit rate and compression (A 66)
4 Frame rate* (A 65)
5 Clip geotagged with GPS information** (A 120, 180)
6 Relay clip** (A 52)
5
indicates the first part of the recording,
6
indicates
the middle part(s) and
7
indicates the last part.
7 Start time code
8 Clip duration
9 Embedded custom picture file** (A 133)
10 Custom picture file’s main settings (A 134)
11 Custom picture file’s detailed settings (A 135)
12 Lens information**
13 User memo information** (A 118)
14 Resolution (A 65)
15 Color sampling (A 65)
16 Custom picture file embedded
17
$
mark**/
%
mark** (A 117, 146)
18 End time code
19 Preset color setting (A 84)
* For XF-AVC clips recorded using slow & fast motion recording, [S&F
REC] and both the shooting frame rate and the playback frame rate will
be displayed.
** Only for XF-AVC clips.
Adding and Deleting
$
Marks or
%
Marks
You can add an OK mark (
$
) or check mark (
%
) to XF-AVC clips recorded on the CFast card in order to tag
them as special clips. Since clips with an
$
mark cannot be deleted with the camera, you can use this mark
also to protect important clips.
1 Select the desired clip (A 142).
Select [CFast (XF-AVC)] as the playback media/format.
2 Add the clip mark (
$
or
%
mark).
[OPTIONS] > [Add
$
Mark] or [Add
%
Mark] > [OK]
Alternatively, you can press an assignable button set to [Add
$
Mark] or [Add
%
Mark] (A 127).
•[
$
Mark] or [
%
Mark] will appear briefly on the monitoring screen and the selected clip mark will be added
to the clip. On the control display,
$
or
%
will appear with the clip details on the PLAY screen.
3 When the confirmation screen appears, press [OK].
NOTES
A clip cannot have both an
$
mark and
%
mark at the same time. When you add a
%
mark to a clip with an
$
mark, the
$
mark will be deleted. Similarly, when you add an
$
mark to a clip with a
%
mark, the
%
mark will be deleted.
14
15
19
16
17
1
2
3
5
7
6
8
9
4
11
10
12
13
18
147
Clip/Photo Operations
Deleting
$
Marks or
%
Marks
1 Select the desired clip (A 142).
In the clip list select a clip with an
$
or
%
mark.
2 Delete the clip mark (
$
or
%
mark).
[OPTIONS] > [Delete
$
Mark] or [Delete
%
Mark] > [OK]
Alternatively, you can press an assignable button set to [Delete
$
Mark] or [Delete
%
Mark] (A 127).
The selected clip mark will be removed from the clip.
3 When the confirmation screen appears, press [OK].
Deleting Clips and Photos
You can delete clips and photos you are not interested in keeping, except for XF-AVC clips with an
$
mark. To
delete such clips, delete the
$
mark beforehand (A 147).
1 Select the desired clip or photo (A 142).
2 Delete the clip or photo.
[OPTIONS] > [Delete]
3 Press both [DELETE] buttons simultaneously.
The clip or photo will be deleted.
4 When the confirmation screen appears, press [OK].
IMPORTANT
Be careful when deleting clips and photos. Deleted recordings cannot be recovered with the camera.
Deleting the User Memo and GPS Information
1 Select the desired clip (A 142).
2 Delete the user memo.
[OPTIONS] > [Delete User Memo]
3 Press both [DELETE] buttons simultaneously.
The user memo and GPS information will be deleted from the clip.
4 When the confirmation screen appears, press [OK].
Clip/Photo Operations
148
Copying a Custom Picture File Embedded in a Clip
You can copy to the camera the custom picture file embedded in an XF-AVC clip.
1 Select the desired clip (A 142).
2 Review the custom picture settings embedded with the clip.
[OPTIONS] > [Copy
/
File]
Turn the SELECT dial to scroll through all the information.
3 Press [FILE] and turn the SELECT dial to select the custom picture file where you want to copy the
settings from the clip.
4 Press both [COPY] buttons simultaneously.
The clip’s custom picture settings will be copied to the selected custom picture file, overwriting any previous
settings.
5 When the confirmation screen appears, press [OK].
NOTES
You cannot copy the custom picture file in a clip to a protected custom picture file.
6
149
External Connections
Video Output Configuration
The video signal output from the SDI OUT terminals, MON. terminals and HDMI
TM
OUT terminal, depends on the
clip’s video configuration and on various menu settings. Refer to the following tables for the video output
configuration from each terminal, depending on the main recording video configuration used.
For details about the video output configuration when using a CDX-36150 Recorder docked with the camera,
refer to
Main Recording Video Configuration and Video Output Configuration from the SDI OUT Terminals
(A 209) and the pages that follow.
Main Recording Video Configuration and Video Output Configuration from
the SDI OUT Terminals
1
[Rec/Media Setup] > [Main Rec Format] setting.
2
The frame rate of the video output will be the same as that used for recording (except when slow & fast motion recording is
activated).
3
The color sampling will be determined by the option selected for the [Rec/Media Setup] > [Resolution/Sampling]
setting.
4
When only one or two SDI connections are required, the other SDI OUT terminals output the same signal as SDI OUT 1 (or SDI
OUT 1 and SDI OUT 2). This is indicated by the gray cells in the table.
5
RGB 4:4:4,10 bit is only available when the main recording format is set to [XF-AVC (CFast)].
6
Only when the resolution is 1920x1080.
Main recording video configuration Output from each terminal
3, 4
Number of
terminals
required
Output
signal
[Main Rec
Format]
1
Resolution/
Color sampling
Frame rate
2
SDI OUT 1 SDI OUT 2 SDI OUT 3 SDI OUT 4
[RAW
(SDI OUT)]
4096x2160
RAW
30P to 60P
(60P inclusive)
Frame-sequential
2
3GRGBA1 RGBA2
30P or lower RGBA 1
[XF-AVC
(CFast)],
[ProRes
(CFast)]
4096x2160
3840x2160
YCbCr 4:2:2, 10 bit
30P to 60P
(60P inclusive)
Square division (Quad HD)
4 3G
Upper left Upper right Lower left Lower right
30P or lower
Square division (Quad HD)
4 HD
Upper left Upper right Lower left Lower right
2048x1080
1920x1080
RGB 4:4:4, 12 or 10 bit
5
30P to 60P
(60P inclusive)
RGB 2
Dual link
3G
30P or lower RGB 1 3G
2048x1080
1920x1080
YCbCr 4:2:2, 10 bit
120P to 240P
(240P inclusive)
Frame sequential
4
3G
YCC1 YCC2 YCC3 YCC4
60P to 120P
(120P inclusive)
Frame sequential
2
YCC1 YCC2
30P to 60P
(60P inclusive)
YCC 1
30P or lower,
59.94i
6
,
50.00i
6
YCC 1 HD
Video Output Configuration
150
Main Recording Video Configuration and Video Output Configuration from the
MON. Terminals and HDMI OUT Terminal
1
[Rec/Media Setup] > [Main Rec Format] setting.
2
The frame rate of the video output will be the same as that used for recording (except when slow & fast motion recording is
activated).
3
Onscreen displays and assistance functions like peaking and zebra pattern can be output to an external monitor (except on a
monitor connected to the HDMI OUT terminal when the terminals output is set to 4K (4096x2160 or 3840x2160)).
4
[System Setup] > [Term. Output Setup] > [MON. Output] setting.
5
When [System Setup] > [Term. Output Setup] > [MON. Output] is set to [Off], the HDMI OUT output will change
depending on the capabilities of the monitor used. When [MON. Output] is set to a setting other than [Off], if the monitor
connected to the terminal does not support the video output configuration, video output from the HDMI OUT terminal will be
turned off. When the horizontal resolution of the recording video configuration is 2048, the sides of the image will be cropped.
6
The color sampling will be set automatically to YCbCr 4:2:2, 10 bit, YCbCr 4:4:4, 8 bit or RGB 4:4:4, 8 bit, depending on the
capabilities of the external monitor. When the output resolution is 4096x2160 or 3840x2160 and the frame rate is 59.94P or
50.00P, the color sampling will be set automatically to YCbCr 4:2:0, 8 bit.
7
[System Setup] > [Term. Output Setup] > [HDMI Max Res.] setting.
[Main Rec Format]
1
Recording video configuration Video output configuration
Frame rate
2
Resolution
MON. terminals
3
HDMI OUT terminal
3, 5, 6
[MON. Output]
4
[HDMI Max Res.]
7
[2048x1080/
1920x1080]
[1920x1080]
[4096x2160/
3840x2160]
[1920x1080]
[RAW
(SDI OUT)]
59.94P
50.00P
29.97P
25.00P
24.00P
23.98P
4096x2160
2048x1080
YCbCr 4:2:2,
10 bit
1920x1080
YCbCr 4:2:2,
10 bit
1920x1080,
720x480
(59.94P),
720x576 (50.00P)
1920x1080,
720x480
(59.94P),
720x576 (50.00P)
[XF-AVC (CFast)],
[ProRes (CFast)]
59.94P
50.00P
29.97P
25.00P
24.00P
23.98P
4096x2160 4096x2160
3840x2160
1920x1080
YCbCr 4:2:2,
10 bit
3840x2160
2048x1080
2048x1080
YCbCr 4:2:2,
10 bit
1920x1080,
720x480
(59.94P),
720x576 (50.00P)
1920x1080
1920x1080
YCbCr 4:2:2,
10 bit
59.94i
50.00i
1920x1080
151
Video Output Configuration
Playback Video Configuration and Video Output Configuration by Terminal
Refer to the following tables for the video output configuration from each terminal, depending on the video
configuration of the clip being played back.
1
During the playback of sub recording (XF-AVC Proxy) clips, if the output of onscreen displays is activated for the MON. terminals,
the onscreen displays will be output also from the SDI OUT terminals.
2
[System Setup] > [Term. Output Setup] > [MON. Output] setting.
3
When [System Setup] > [Term. Output Setup] > [MON. Output] is set to [Off], the HDMI OUT output will change
depending on the capabilities of the monitor used. When [MON. Output] is set to a setting other than [Off], if the monitor
connected to the terminal does not support the video output configuration, video output from the HDMI OUT terminal will be
turned off.
4
The color sampling will be set automatically to YCbCr 4:2:2, 10 bit, YCbCr 4:4:4, 8 bit or RGB 4:4:4, 8 bit, depending on the
capabilities of the external monitor.
5
[System Setup] > [Term. Output Setup] > [HDMI Max Res.] setting.
6
Only available when [System Setup] > [Term. Output Setup] > [SDI OUT Output] is set to [Off].
7
RGB 4:4:4,10 bit is only available when the main recording format is set to [XF-AVC (CFast)].
Video configuration of the clip Video output configuration
Resolution Frame rate SDI OUT terminals
1
MON. terminals HDMI OUT terminal
3, 4
[MON. Output]
2
[HDMI Max Res.]
5
[2048x1080/
1920x1080]
[1920x1080]
[4096x2160/
3840x2160]
[1920x1080]
4096x2160
59.94P
50.00P
29.97P
25.00P
24.00P
23.98P
4096x2160
YCbCr 4:2:2, 10 bit
2048x1080
YCbCr 4:2:2, 10 bit
1920x1080
YCbCr 4:2:2, 10 bit
4096x2160
6
1920x1080,
720x480 (59.94P),
720x576 (50.00P)
3840x2160
3840x2160
YCbCr 4:2:2, 10 bit
1920x1080
YCbCr 4:2:2, 10 bit
3840x2160
6
2048x1080
2048x1080 /
RGB 4:4:4, 12 or 10 bit
7
,
YCbCr 4:2:2, 10 bit
2048x1080
YCbCr 4:2:2, 10 bit
1920x1080,
720x480 (59.94P),
720x576 (50.00P)
1920x1080
1920x1080 /
RGB 4:4:4, 12 or 10 bit
7
,
YCbCr 4:2:2, 10 bit
1920x1080
YCbCr 4:2:2, 10 bit
1920x1080
59.94i
50.00i
1920x1080
YCbCr 4:2:2, 10 bit
Connecting to an External Monitor or Recorder
152
Connecting to an External Monitor or Recorder
When you connect the camera to an external device, be it a monitor (to monitor the recording or for playback) or
an external video recorder (for recording), use the terminal on the camera that matches the one you wish to use
on the external device. Then, check the video signal output configuration (A 149).
Connection Diagram
We recommend that you power the camera from a power outlet using an AC adapter.
Using the SDI OUT Terminals
The digital signal that is output from the SDI OUT terminals includes the video signal, audio signal (4 channels*),
time code, metadata and clip file name information**. You can connect an external video recorder to the
camera’s SDI OUT terminals to record 4K or 2K video.
For details about how to use and configure external recorders or displays, refer to the instruction manual of the
external device used.
* During RAW output, 2-channel 16-bit audio will be output instead (transmitted as 20 bits). You can select which audio channels
to output (A 160).
** If the main recording format is set to [ProRes (CFast)] but no CFast card is inserted in the camera, clip file name information will
not be output.
1 To output RAW video, set the main recording format to [RAW (SDI OUT)] (A 65).
Video output from the SDI OUT terminals will be activated automatically so step 2 is not necessary.
2 When the main recording format is not [RAW (SDI OUT)], activate the SDI OUT terminals.
[System Setup] (
B
) > [Term. Output Setup] > [SDI OUT Output] > [On]
If you have no intention to use the SDI OUT terminals, select [Off] instead.
3 If necessary, select the 3G-SDI mapping level for the output signal (step 2, A 153).
HDMI OUT
terminal
HDMI cable
(commercially available)
SDI OUT terminals
BNC cables
(commercially available)
SDI inputs
External
monitor/
digital video
recorder
HDMI input
MON.
terminals
BNC cables
153
Connecting to an External Monitor or Recorder
NOTES
Depending on the external recorder, you may not be able to record at the desired video configuration.
After you connect the camera to the external recorder, make a test recording first to check that audio and
video are recorded correctly on the external recorder.
You can set [Rec/Media Setup] > [Rec Command] to [On] to use the camera’s REC button to
control also the recording operation of an external recorder connected to the SDI OUT terminals and MON.
terminals.
About RAW output:
- A special gamma curve optimized for RAW video is applied to the video output.
- During RAW output, the audio output signal will be 2-channel linear PCM audio (16 bit). We recommend
using instead the 4-channel linear PCM audio (24 bit) that is recorded in the camera with sub recording
(XF-AVC Intra) clips.
- The output signal mapping will be set to Level B.
When 2K RGB 4:4:4 video is being output from the SDI OUT terminals, video output from the MON. terminals
will be a 2K YCbCr video signal.
Using the MON. Terminals
The digital signal that is output from the MON. terminals includes the video signal, audio signal (4 channels), time
code, metadata and clip file name information*. Additionally, you can output also the camera’s onscreen displays
and various assistance displays (onscreen markers, zebra patterns, peaking, magnification, false color display,
black & white image).
* If the main recording format is set to [ProRes (CFast)] but no CFast card is inserted in the camera, clip file name information will
not be output.
1 Activate the MON. terminals and select the desired output mode.
[System Setup] (
B
) > [Term. Output Setup] > [MON. Output] > [1920x1080] or
[2048x1080/1920x1080]
If you have no intention to use the MON. terminals, select [Off] instead.
2 If you selected 2K output, you can select the 3G-SDI mapping level for the output signal.
From the same submenu: [3G-SDI Mapping] > [Level A] or [Level B]
The options correspond to a video output signal compliant with Level A or Level B of the SMPTE ST 425
standard.
Options
[2048x1080/1920x1080]: Outputs video with a resolution of 2048x1080 or 1920x1080.
[1920x1080]: Outputs 1920x1080 (Full HD) video. When the horizontal resolution of the main recording video
configuration is 4096 or 2048, the sides of the image will be displayed letterboxed.
NOTES
You can set [Rec/Media Setup] > [Rec Command] to [On] to use the camera’s REC button to
control also the recording operation of an external recorder connected to the SDI OUT terminals and MON.
terminals. However, this is not available from the MON. terminals when the sensor mode is set to [Full Frame]
and the frame rate is set to 59.94P or 50.00P.
Connecting to an External Monitor or Recorder
154
Using the HDMI OUT Terminal
The HDMI
TM
OUT terminal also offers a digital connection and outputs both a video and audio signal. You can
select the maximum resolution of the video signal to output up to 4K video. Additionally, you can output also the
camera’s onscreen displays and various assistance displays (onscreen markers, zebra patterns, peaking,
magnification, false color display, black & white image). The audio output signal will be 2-channel linear PCM
audio (16-bit, 48 kHz sampling). You can select which audio channels to output (A 160).
1 Select the HDMI OUT terminal’s maximum resolution.
[System Setup] (
B
) > [Term. Output Setup] > [HDMI Max Res.] > [4096x2160/
3840x2160] or [1920x1080]
NOTES
When [System Setup] > [Term. Output Setup] > [MON. Output] is set to [Off], the HDMI OUT
output will change depending on the capabilities of the monitor used. When [MON. Output] is set to a setting
other than [Off], if the monitor connected to the terminal does not support the video output configuration,
video output from the HDMI OUT terminal will be turned off.
The HDMI OUT terminal is for output only. Do not connect the camera to another device’s output terminal
using the HDMI OUT terminal as this will cause a malfunction.
Correct operation cannot be guaranteed when connecting the camera to DVI monitors.
Video may not be output correctly depending on the monitor. In such case, use another terminal.
Superimposing Onscreen Displays on Video Outputs
You can choose to output the camera’s onscreen displays along with the video output from the VIDEO terminal
(optional viewfinder), MON. terminals or HDMI OUT terminal to show the camera’s onscreen displays on
monitoring devices connected to the corresponding terminals. This will not affect your recordings or video output
from the SDI OUT terminals.
1 Open the [OSD Output] submenu.
[Monitoring Setup] (
¢
) > [OSD Output] > [VIDEO] (optional viewfinder) or [MON.+HDMI]
(external monitors) > [Output]
2 Select [On] and then press SET.
Alternatively, you can press an assignable button set to [OSD Output: VIDEO] (optional viewfinder only),
[OSD Output: MON.+HDMI] (external monitors only) or [OSD Output] (all monitoring devices at once)
(A 127).
T
appears at the right of the monitoring screen (in shooting mode, only if [Monitoring Setup]
> [Custom Display 2] > [OSD Output] is set to [On]).
NOTES
When the HDMI OUT terminal’s resolution is set to 4096x2160 or 3840x2160, the camera’s onscreen displays
will not be displayed on the monitor connected to the HDMI OUT terminal.
155
Applying a LUT to Video Outputs
Applying a LUT to Video Outputs
While recording using special gamma curves, you can apply a LUT to video output from the VIDEO terminal
(optional viewfinder), SDI OUT terminals, MON. terminals or HDMI OUT terminal. You can even create a LUT file
(.cube format) with Blackmagic Design’s DaVinci Resolve and load it in the camera (A 157).
When a LUT is applied, the displayed image will look as if a standard gamma curve and color space were used,
making it easier to check the image on the monitoring device used. To check the image on an external monitor,
you will need a monitor that is compatible with the selected color space.
Available preset LUT options by gamma curve and color space
Available LUTs depend on the combination of gamma curve and color space used, whether it was set through
one of the preset color settings or through the individual main settings in the custom picture file (A 134).
* Only when [COLOR] > [CP MAIN] > [Preset] is set to [Canon Log 2 : C.Gamut] or [Canon Log 3 : C.Gamut].
1 Open the preset LUT selection submenu.
HOME screen: [COLOR] > [LUT]
Monitoring menu: [Monitoring Setup] (
¢
) > [LUT]
2 Select the desired terminal and then press SET.
Using the control display, you can also select [
8
XF-AVC] to apply a LUT to sub recording (XF-AVC Proxy)
clips when the simultaneous sub recording is activated (A 71). From the monitoring menu select the LUT
for XF-AVC Proxy clips with the [Rec/Media Setup] > [Sub Rec (XF-AVC)] > [Apply LUT] setting
instead.
3 Select the desired LUT and then press SET.
Repeat steps 2 and 3 as necessary to select the LUT applied to other output terminals.
The gamma curve and color space of the video output will change.
If a LUT is not needed, select [Off].
[Gamma] [Color Space]
Available LUTs
[BT.709] [BT.2020] [DCI] [ACESproxy] [HDR-PQ] [HDR-HLG]
[HDR 1600%]/
[HDR 400%]
[Canon Log 2]/
[Canon Log 3]
[Cinema Gamut] Ü Ü Ü Ü* Ü Ü Ü
[BT.2020 Gamut] Ü Ü Ü Ü Ü
[DCI-P3 Gamut] Ü Ü
[BT.709 Gamut] Ü
[Canon Log] [BT.709 Gamut] Ü
[Wide DR] [BT.2020 Gamut] Ü
Applying a LUT to Video Outputs
156
Options
1
Not available for the VIDEO terminal (optional viewfinder).
2
For the HDMI OUT terminal, this option is not available when the terminal’s output resolution is set to 4096x2160 or 3840x2160
and the frame rate is set to 59.94P or 50.00P.
3
Only available for the VIDEO terminal (optional viewfinder).
NOTES
When you apply the [ACESproxy] LUT to the SDI OUT terminals, MON. terminals or HDMI OUT terminal, the
selected terminal will output ACESproxy video data. Using a compatible monitor*, you can perform on-set
color grading and check the image after color correction as you continue shooting (A 22).
* When using the HDMI OUT terminal, a monitor that supports full range YCbCr quantization is required.
If you set an assignable button to [LUT] (A 127), you can press the button to turn on and off the LUTs applied
to all video outputs at once.
If you change the [Gamma] or [Color Space] settings in the custom picture file (A 134), all the LUT settings
will be reset to [Off].
Applied LUT
Output Settings with LUT
applied
Description
Gamma curve Color space
[BT.709] Wide DR BT.709
LUT for viewing on the optional viewfinder and external monitors compatible with
BT.709 specifications.
[BT.2020]
1
Wide DR BT.2020
LUT for viewing on external monitors compatible with ITU-R BT.2020 standards,
which define parameters for ultra-high-definition television (4K/8K).
[DCI]
1
DCI DCI-P3
LUT for viewing on external monitors that support color spaces and gamma curves
that follow the guidelines established by DCI (Digital Cinema Initiatives).
[ACESproxy]
1
ACESproxy ACESproxy
LUT for viewing on external monitors compatible with the ACESproxy standard
established by ACES (Academy Color Encoding System). The signal output will use full
range coding.
[HDR-PQ]
1, 2
PQ BT.2020
LUT for viewing HDR (high dynamic range) images on external monitors compatible
with the PQ standard defined by ITU-R BT.2100. The signal output will use narrow
range (video range) coding.
[HDR-HLG]
1, 2
HLG BT.2020
LUT for viewing HDR (high dynamic range) images on external monitors compatible
with the HLG standard defined by ITU-R BT.2100. The signal output will use narrow
range (video range) coding.
[HDR 1600%]
3
Original
gamma curve
BT.709
LUT for viewing HDR (high dynamic range) images on the optional viewfinder and
other monitoring devices. The LUT follows the ITU-R BT.2100 transfer function to
convert a brightness range of 1600% or 400% respectively into a linear brightness
scale.
[HDR 400%]
3
[Off] No LUT applied.
157
Applying a LUT to Video Outputs
Using a User LUT
Once you create a LUT file (.cube format) with Blackmagic Design’s DaVinci Resolve, you can register it in the
camera as a user LUT and then apply it to some video outputs in a similar way to the preset LUTs. When
recording using special gamma curves, you can apply the user LUT to video output from the VIDEO terminal
(optional viewfinder), SDI OUT terminals, MON. terminals or HDMI OUT terminal. Use an SD card to load up to
four LUTs into the camera and register them.
Note that you cannot apply the user LUT to sub recording (XF-AVC Proxy) clips.
Registering a User LUT
1 Insert the SD card containing the LUT file (.cube format) created in Blackmagic Design’s DaVinci Resolve into
the camera’s SD card slot.
2 Open the [Register] submenu.
HOME screen: [COLOR] > [USER LUT] > [Register]
Monitoring menu: [Monitoring Setup] (
¢
) > [LUT] > [User LUT] > [Register]
3 Turn the SELECT dial to select a slot in the camera (user LUT 1 to 4) to which the LUT file will be saved and
then press SET.
4 Select the desired LUT file on the SD card and then press SET.
5 Select the desired output color space and then press SET.
Available options are [BT.709 Gamut] and [BT.2020 Gamut]. To leave the color space unconverted, select
[Do Not Convert].
6 Select the desired output range and then press SET.
Available options are [Narrow Range] and [Full Range].
7 Press both [LOAD] buttons simultaneously (HOME screen) or select [OK] and then press SET (monitoring
menu).
The selected LUT file will be registered in the camera.
8 Press [OK] (HOME screen) or press SET (monitoring menu).
Applying a User LUT to Video Outputs
1 Open the [LUT] submenu.
HOME screen: [COLOR] > [LUT]
Monitoring menu: [Monitoring Setup] (
¢
) > [LUT]
2 Select the desired terminal and then press SET.
3 Select the desired user LUT (user LUT 1 to 4) and then press SET.
Only registered user LUTs are displayed.
The user LUTs are displayed with a icon in front of the name.
Selecting the Output Color Space
If you select an output color space, the color space will be converted when the user LUT is applied.
1 Open the [Color Space(Output)] submenu.
HOME screen: [COLOR] > [USER LUT] > [Color Space(Output)]
Monitoring menu: [Monitoring Setup] (
¢
) > [LUT] > [User LUT] > [Color Space(Output)]
2 Turn the SELECT dial to select the desired user LUT (user LUT 1 to 4) and then press SET.
3 Select the desired output color space and then press SET.
Applying a LUT to Video Outputs
158
Available options are [BT.709 Gamut] and [BT.2020 Gamut]. To leave the color space unconverted, select
[Do Not Convert].
Selecting the Output Range
You can select the output range for the video output.
1 Open the [Range(Output)] submenu.
HOME screen: > [COLOR] > [USER LUT] > [Range(Output)]
Monitoring menu: > [Monitoring Setup] (
¢
) > [LUT] > [User LUT] > [Range(Output)]
2 Turn the SELECT dial to select the desired user LUT (user LUT 1 to 4) and then press SET.
3 Select the desired output range and then press SET.
Available options are [Narrow Range] and [Full Range].
Deleting User LUTs
You can delete user LUTs in the camera either individually or all at once.
1 Open the screen for deleting user LUT files.
HOME screen: [COLOR] > [USER LUT] > [Delete] or [Reset All]
Monitoring menu: [Monitoring Setup] (
¢
) > [LUT] > [User LUT] > [Delete] or [Reset All]
If you intend to delete user LUT files individually, continue to step 2. Otherwise, skip to step 3.
2 Turn the SELECT dial to select the desired user LUT (user LUT 1 to 4) and then press SET.
3 HOME screen: Press both [DELETE] buttons (for the [Delete] option) or [RESET] buttons (for the [Reset All]
option) simultaneously.
Monitoring menu: Select [OK] and then press SET.
Depending on the method chosen in step 1, one or all user LUT files will be deleted.
4 Press [OK] (HOME screen) or press SET (monitoring menu).
Renaming User LUTs
You can rename each of the four user LUT files in the camera.
1 Open the [Rename] submenu.
HOME screen: [COLOR] > [USER LUT] > [Rename]
Monitoring menu: [Monitoring Setup] (
¢
) > [LUT] > [User LUT] > [Rename]
2 Turn the SELECT dial to select the desired user LUT (user LUT 1 to 4).
3 Enter the desired name (up to 8 characters) using the keyboard screen (A 37).
Displaying User LUT Information
1 Open the [Display Info] submenu.
HOME screen: [COLOR] > [USER LUT] > [Display Info]
Monitoring menu: [Monitoring Setup] (
¢
) > [LUT] > [User LUT] > [Display Info]
2 Turn the SELECT dial to select the desired user LUT (user LUT 1 to 4) and then press SET.
NOTES
The camera supports 3D LUT files (.cube format) created with Blackmagic Designs DaVinci Resolve in 33 grid
format. Save the file in the root folder of the SD card.
The following LUT files are not supported.
- Files 2 MB and larger.
159
Applying a LUT to Video Outputs
- Files with a file name containing over 64 characters, including the .cube file extension.
If the correct color space conversion is not selected, clips with a video configuration using YCbCr will not be
output correctly.
The following characters can be used in the file name:
Numbers 0 to 9, upper/lower case letters a to z, underscore (_), hyphen (-), period (.) and single-byte space.
User LUT files in the camera cannot be overwritten. If necessary, delete a user LUT file in the camera before
registering a LUT file.
Audio Output
160
Audio Output
The camera can output audio from the SDI OUT terminals, MON. terminals, HDMI OUT terminal or
×
(headphone) terminal. The audio signal recorded with main recording clips recorded in the camera is 4-channel
linear PCM audio, 24 bit. The number of audio channels output and the audio bit depth depend on the terminal
used and other settings.
SDI OUT terminals: During RAW video output: 2 channels*, 16 bit
During 2K output: 4 channels, 24 bit
MON. terminals: 4 channels, 24 bit
HDMI OUT terminal: 2 channels*, 16 bit
×
(headphone) terminal: 2 channels*
* You can select which two channels of the four audio channels recorded will be output from the terminal.
1 Open the audio channel selection screen/submenu for the desired terminal.
Setup screen: [AUDIO] > [MONITOR] or
[AUDIO] > [OPTIONS] > [Audio Output] > [HDMI Channels] or [RAW (SDI)
Channels]
Monitoring menu: [Audio Setup] (
¡
) > [Audio Output] > [Monitor Channels], [HDMI Channels] or
[RAW (SDI) Channels]
In playback mode: [Audio Setup] > [Monitor Channels] or [HDMI Channels]
[MONITOR]/[Monitor Channels]: audio from the
×
(headphone) terminal; [HDMI Channels]: audio output
from the HDMI OUT terminal; [RAW (SDI) Channels]: audio output from the SDI OUT terminals during RAW
video output.
Alternatively, you can press an assignable button set to [Monitor Channels] (A 127) to cycle among the
audio channel output options for the headphone terminal only.
2 Select the desired option and then press SET.
The options show combinations of audio channels output from the left and right, respectively (L/R). For the
headphones output, options with a “+” sign (for example “CH1+2”) indicate a mix of two audio channels
output from the same side.
The audio channels selected for output from the
×
(headphone) terminal will appear at the right of the
monitoring screen, under the audio level indicators (in shooting mode, only if [Monitoring Setup]
> [Custom Display 2] > [Audio Lvl Indicator] is set to [On]).
161
Working with Clips on a Computer
Working with Clips on a Computer
Canon offers software applications as free downloads that allow you to save XF-AVC clips recorded with the
camera on a computer, develop RAW clips, and more.
Saving Clips to a Computer
You can use Canon XF Utility to save and organize clips on a computer and the Canon XF plugins to easily use
the clips directly from major non-linear editing (NLE) applications. The software and plugins are available as free
downloads from your local Canon Web site. Check the download page for the system requirements and the
latest information about the software.
You will find detailed instructions about installing and uninstalling the software in the “Read This First” PDF file
included in the compressed file you will download from the Web site. For details about using the software, refer
to the instruction manual (PDF file) that is installed with the software.
Canon XF Utility: Software application that allows you to save clips on a computer, check, play back and
organize clips and grab still frames from clips. The software is available for Windows and macOS.
Canon XF Plugin for Avid Media Access: Plugin that allows you to easily import clips from a recording media or a
local folder in the computer to the compatible version of Avid Media Composer (an NLE application compatible
with Avid Media Access), directly from within the application. The plugin is available for the Windows and macOS
versions of Avid Media Composer.
Z[]
Canon XF Plugin for Final Cut Pro X: Plugin that allows you to easily transfer clips
from a recording media or a local folder in the computer to the compatible version of Apple’s Final Cut Pro X,
directly from within the NLE application.
Developing RAW Clips
Use the Cinema RAW Development software to develop RAW clips shot/recorded with the camera. After you
develop the clips and export them to a full-quality standard file type such as DPX, they will be ready for color
grading. Alternatively, you can use the Canon RAW Plugin to easily use RAW clips unaltered (in RAW format)
directly from major non-linear editing (NLE) applications. The software and plugin are available as free downloads
from your local Canon Web site. Check the download page for the system requirements and the latest
information about the software.
You will find detailed instructions about installing and uninstalling the software in the “Read This First” PDF file
included in the compressed file you will download from the Web site. For details about using the software, refer
to the instruction manual (PDF file) that is installed with the software.
Cinema RAW Development: Software application that allows you to develop, play back and export RAW clips.
The software is available for Windows and macOS.
Canon RAW Plugin for Avid Media Access: Plugin that allows you to easily import RAW clips from a storage
device or a local folder in the computer to the compatible version of Avid Media Composer (an NLE application
compatible with Avid Media Access), directly from within the application. The plugin is available for the Windows
and macOS versions of Avid Media Composer.
Working with Clips on a Computer
162
7
163
Network Functions
About the Network Functions
You can attach the optional WFT-E6 or WFT-E8 Wireless File Transmitter to the camera to connect it to a Wi-Fi
network (A 164). You can also use an Ethernet cable to connect the camera to a network using a wired
connection (A 168). After the camera is connected to a network, you can use the following network functions.
Network functions and connection types
1
Connection to a Wi-Fi network via an external access point (wireless router, etc.)
2
Direct connection to one Wi-Fi-enabled device where the camera serves as the Wi-Fi access point.
Before using the network functions
The instructions in this chapter assume you already have a correctly configured and working network, network
device(s) and/or Wi-Fi access point. If necessary, refer to the documentation provided with the network
devices you plan to use.
Configuring the network settings requires adequate knowledge about configuring and using wired (Ethernet)
and/or wireless (Wi-Fi) networks. Canon cannot provide support regarding network configurations.
IMPORTANT
Data transmitted over networks is not encrypted.
Canon shall not be liable for any loss of data or damage resulting from incorrect network configuration or
settings. Additionally, Canon shall not be liable for any loss or damage caused by the use of network functions.
Using an unprotected Wi-Fi network can expose your data to monitoring by unauthorized third parties. Also,
the camera is shipped with default passwords so you can test the network functions as soon as possible.
Changing the initial settings is recommended. Be aware of any data security risks involved.
NOTES
NOTES
Do not open the card slot covers of any recording media while using network functions.
Do not lay cables connected to the SDI OUT terminals, MON. terminal or HDMI OUT terminal near the optional
Wireless File Transmitter. Doing so may negatively affect the wireless communication over Wi-Fi.
Network function Description
Wired
network
Wi-Fi
A
Infrastructure
1
Camera Access
Point
2
Browser Remote
Control the camera remotely from the Web
browser of a connected device.
Ü Ü 170
IP Streaming
Stream the camera’s live video and audio over
IP to a compatible IP video decoder connected
to the same network.
Ü Ü 182
FTP File Transfer
Transfer clips recorded with the camera to
another device connected to the network using
the FTP protocol.
Ü Ü
185
Connecting to a Wi-Fi Network
164
Connecting to a Wi-Fi Network
Attaching the Optional Wireless File Transmitter
Turn off the camera and attach the optional WFT-E6 or WFT-E8
Wireless File Transmitter (hereafter, simply “wireless
transmitter”) to the camera’s system extension terminal.
1 Press the
Q
button to turn off the camera.
2 Attach the optional wireless transmitter to the camera’s
system extension terminal.
3 Fasten the wireless transmitter’s locking screw.
4 Attach the supplied extension unit attachment bracket
to secure the wireless transmitter.
Once the wireless transmitter is correctly attached to the camera, you can connect
the camera in Infrastructure mode, using an access point (wireless router etc.), or in Camera
Access Point mode, directly to a network device. The type of connection you can use, depends
on the network function you wish to use (A 163).
For an Infrastructure connection, the camera offers 3 ways to configure an access point and the method you use
will depend on the type and specifications of the access point and network you plan to use.
Camera Access Point: When shooting in a location where there are no access points available, the camera can
serve as a wireless access point*. Wi-Fi enabled devices will be able to connect to the camera directly.
* Limited only to the connection between the camera and supported Wi-Fi enabled devices. The functionality is not the same as
that of commercially available access points.
Infrastructure connection:
WPS (button): If your wireless router supports Wi-Fi Protected Setup (WPS), setup will be
easy and require minimal configuring and no passwords. To check if your wireless router
has a WPS button and for details about how to activate the Wi-Fi protected setup, refer to
the instruction manual of your wireless router.
WPS (PIN code): Even if your wireless router does not have a dedicated WPS button, it may support WPS using
a PIN code instead. For setup using a PIN code, you will need to know in advance how to activate the wireless
router’s WPS function. For details refer to the instruction manual of your wireless router.
Searching for Access Points: If your access point does not support the WPS function or you cannot activate it,
you can have the camera search for access points in the area.
IMPORTANT
Depending on the country/region of use, some restrictions on outdoor use or camera access point
connections may apply when operating the IEEE802.11a/n wireless standard in the 5 GHz band. For details
see
Areas of Use and Restrictions
(a separate leaflet supplied with the wireless transmitter).
165
Connecting to a Wi-Fi Network
Camera Access Point
In this mode the camera itself serves as a wireless access point to which other Wi-Fi-enabled devices can
connect. Initially, basic settings for a Camera Access Point connection are configured in the camera. Follow the
procedure below to change the initial settings.
1 Open the [Browser Remote] setup screen/submenu.
Setup screen: [NETWORK] > [Browser Remote]
Monitoring menu: [System Setup] (
B
) > [Network Settings] > [Browser Remote]
The current connection configuration appears on the control display. Turn the SELECT dial to scroll through
all the connection settings.
2 Change the connection method.
Setup screen: [OPTIONS] > [Connection Method]
Monitoring menu: From the same submenu select [Connection Method].
3 Select [Camera Access Point] and then press SET.
4 Change the SSID (network name) the camera will use as a Wi-Fi access point.
Setup screen: [SSID] > [EDIT]
Monitoring menu: [SSID] > [Input]
Enter the desired network name using the keyboard screen (A 37).
The network name is needed to connect the network device to the camera. If necessary, write it down.
5 Select the frequency band for the Wi-Fi connection.
[Frequency] > [5 GHz] or [2.4 GHz] > press SET
6 Select the Wi-Fi channel.
[Channel] > desired channel > press SET
Available channels will be different depending on the wireless connection mode selected in the previous step
and the model of wireless file transmitter used. For details, refer to the “Areas of Use and Restrictions” leaflet
supplied with the optional WFT-E6 or WFT-E8 Wireless File Transmitter.
7 Select the encryption method.
[Authn/Encr Method] > [WPA2-PSK/AES] or [Open/No encryption] > press SET
If you selected [Open/No encryption], the rest of the procedure is not necessary.
8 Change the default password.
Setup screen: Select [Password] and press SET.
Monitoring menu: [Password] > [Input] > press SET
Enter the desired text using the keyboard screen (A 37).
This password is needed to connect the network device to the camera. If necessary, write it down.
Connecting in Infrastructure Mode
1 Open the [IP Streaming] or [FTP Transfer] setup screen/submenu.
Setup screen: [NETWORK] > [IP Streaming] or [FTP Transfer]*
Monitoring menu: [System Setup] (
B
) > [Network Settings] > [IP Streaming] or [FTP Transfer]**
* The camera will switch automatically to playback mode when you select [FTP Transfer].
** From the playback screen only.
The current connection configuration appears on the control display. Turn the SELECT dial to scroll through
all the connection settings.
2 Change the connection method.
Setup screen: [OPTIONS] > [Connection Method]
Monitoring menu: From the same submenu select [Connection Method].
Connecting to a Wi-Fi Network
166
3 Select [Infrastructure] and then press SET.
4 Select the desired method to configure the access mode.
[Wi-Fi Setup Method] > desired method > press SET
Continue the setup with the procedure corresponding to the method you wish to use (see the reference
pages below).
[WPS: Button] (A 166) [WPS: PIN Code] (A 166) [Search for Access Points] (A 167)
Wi-Fi Protected Setup (WPS)
Wi-Fi Protected Setup (WPS) is the easiest way to set up a Wi-Fi access point. You can do simply by pushing a
button (if the access point (wireless router) you want to connect to has a WPS button) or using a PIN code
issued by the camera.
Wireless Routers with a WPS Button
1 Press and hold the WPS button on the wireless router.
The length of time required to hold down the WPS button depends on the wireless router. Refer to the
instruction manual of your wireless router and make sure the wireless router’s WPS function is activated.
2 Within 2 minutes, press [OK] (setup screen) or press SET (monitoring menu).
While [Connecting] appears on the screen, you can press [CANCEL] (setup screen) or press SET (monitoring
menu) to cancel the operation.
NOTES
NOTES
The [WPS: Button] method may not work correctly if there are several active access points in the area. In such
case try using [WPS: PIN Code] or [Search for Access Points] (A 167) instead.
WPS using a PIN code
1 After you select [WPS: PIN Code], the camera will generate and display an 8-digit PIN code on the
control display.
2 Enter the PIN code into the wireless router’s WPS (PIN code) setup screen.
For most wireless routers, you must use a Web browser to access the setup screen.
For details about how to access your wireless routers settings and activate the Wi-Fi Protected Setup
(WPS) using a PIN code, refer to the instruction manual of your wireless router.
3 Within 2 minutes, press [OK] (setup screen) or press SET (monitoring menu).
While [Connecting] appears on the screen, you can press [CANCEL] (setup screen) or press SET (monitoring
menu) to cancel the operation.
After the connection is correctly established, the previous menu screen will appear again on the control
display.
167
Connecting to a Wi-Fi Network
Searching for Access Points
The camera will automatically detect access points in the vicinity. After you select the desired access point, you
only need to enter the selected network’s password to connect the camera. For details about the access point’s
network name (SSID) and password refer to the wireless router’s instruction manual or consult the network
administrator in charge of the access point.
1 After you select [Search for Access Points], the camera will search for active access points in the
vicinity and display a list of available options on the control display.
2 Turn the SELECT dial to select the desired access point and then press [OK] (setup screen) or press
SET (monitoring menu).
3 Enter the password of the access point.
Setup screen: Select [Password] and press SET.
Monitoring menu: [Password] > [Input] > Press SET
Enter the desired text using the keyboard screen (A 37).
If the access point is not encrypted (C), this step is not required.
NOTES
NOTES
Valid passwords vary depending on the encryption method.
64-bit WEP encryption: 5 ASCII characters or 10 hexadecimal characters.
128-bit WEP encryption: 13 ASCII characters or 26 hexadecimal characters.
AES / TKIP encryption: 8 to 63 ASCII characters or 64 hexadecimal characters.
* Note: ASCII characters include the numbers 0 to 9, the letters a to z and A to Z and some punctuation marks and special
symbols. Hexadecimal characters comprise the numbers 0 to 9 and the letters a to f and A to F.
Network name (SSID)
Current access point/Total number
of active access points detected
Encrypted access point
Connecting to a Wired (Ethernet) Network
168
Connecting to a Wired (Ethernet) Network
Connect the camera to a router or other device connected to a wired (Ethernet) network using a commercially
available Ethernet cable. Use Category 5e, shielded twisted pair (STP) Ethernet cables compatible with Gigabit
Ethernet (1000BASE-T) and with good shielding capability.
1 Connect a commercially available Ethernet cable to the (Ethernet) terminal on the camera and an
Ethernet port on a network device.
2 Open the [Connection Method] submenu of the desired network function.
Setup screen: [NETWORK] > Desired function* > [OPTIONS] > [Connection Method]
Monitoring menu: [System Setup] (
B
) > [Network Settings] > Desired function** > [Connection
Method]
* The camera will switch automatically to playback mode when you select [FTP Transfer].
** [FTP Transfer] from the playback screen only.
3 Select [Ethernet] and then press SET.
(Ethernet) access
indicator
Ethernet cable
(commercially available)
Ethernet port on a
network device
169
Checking the Network’s Status and Settings
Checking the Network’s Status and Settings
After activating a network function, the camera will connect to the network that was configured in advance. The
icons displayed on the control display and at the top left of the monitoring screen will indicate the type of network
selected and the connection status.
Wi-Fi (Infrastructure): In yellow – the camera is connecting to or disconnecting from the network. In white –
the network function can be used.
Wi-Fi (Camera Access Point): In yellow – starting the camera’s access point. In white – the camera’s access
point is ready. Connect the Wi-Fi enabled device to the camera.
Ethernet: In yellow – the camera is connecting to or disconnecting from the network. In white – the
network function can be used.
The (Ethernet) indicator next to the terminal will flash or illuminate as follows*: Flashing in
green – connecting to the network or streaming video (IP streaming only); illuminated in green –
Browser Remote or FTP transfer active; flashing in red – network error.
: Browser Remote (A 170)
:IP streaming (A 182)
* You can also set [System Setup] > [LED] > [LAN (Ethernet)] to [Off] to disable the indicator.
Checking and Changing Network Settings
The camera’s network functions are optimized to work automatically with minimal setup by the user. Still, you
have the option to change manually more advanced network settings to suit specific needs. Changing settings
manually requires more advanced knowledge of Wi-Fi and network settings.
1 Review the network settings of the desired function.
Setup screen: [NETWORK] > Desired function > [OPTIONS]
Monitoring menu: [System Setup] (
B
) > [Network Settings] > Desired function
The submenu that opens will list all the network settings relevant to the selected network function. Turn the
SELECT dial to scroll and review all the information.
Monitoring menu only: You can select [Display Info] and press SET to view a summary of all the network
settings. Push the joystick up/down to view other pages or press SET to return to the previous submenu.
2 Select the network setting you wish to change and press SET.
3 Select an option and press SET or enter the required text/numbers using the keyboard screen
(A 37).
Browser Remote: Controlling the Camera from a Network Device
170
Browser Remote: Controlling the Camera from a Network Device
After connecting the camera to a network (Wi-Fi or wired using the (Ethernet) terminal), you can operate the
camera remotely via Browser Remote, a Web browser application that can be accessed using the Web browser
on network devices* (via Wi-Fi or with an Ethernet connection). Using Browser Remote, you can check the
camera’s live view image, control various recording settings, set and change metadata** and add marks to the
clip. On the Browser Remote screen, you can also check the remaining recording time on the recording media,
power source levels and the camera’s time code.
* For details about compatible devices, operating systems, Web browsers, etc., please visit your local Canon Web site.
** XF-AVC clips only.
Setting Up Browser Remote
Initially, basic default network settings for a browser connection (camera ID, user names and passwords) are
already saved in the camera*. At default settings, Browser Remote is set up for use by a single user ([Full] – full
control user). With the following procedures you can change the default settings, if you prefer.
* To check the settings: [NETWORK] > [Browser Remote] (camera menu) or [System Setup] (
B
) > [Network
Settings] > [Browser Remote] > [Display Info] (monitoring menu).
Camera Settings
You can set a unique camera identification code and designate the port that Browser Remote will use when
accessing the camera through a network. The port number (HTTP protocol) used by Browser Remote is usually
set to port 80, but you can change it if necessary. The camera ID will appear on the Browser Remote screen,
making it easy to identify which camera the application is controlling in case of a multi-camera shooting setup.
1 Open the Browser Remote’s settings submenu.
Setup screen: [NETWORK] > [Browser Remote] > [OPTIONS]
Monitoring menu: [System Setup] (
B
) > [Network Settings] > [Browser Remote]
2 Change the camera ID.
Setup screen: [Camera ID] > [EDIT]
Monitoring menu: [Camera ID] > [Input] > press SET
Enter the desired text using the keyboard screen (A 37).
3 If necessary, select [Port No.] and press SET to change the port number using the keyboard screen (A 37).
Camera menu only: Press [RESET] to reset the port number to [80].
User Settings
A user name and password are required before the Browser Remote application can access and operate the
camera. You can set up to three different users and select whether you want to allow single-user operation
(full control) or two-user operation (one controlling camera functions and another in charge of metadata input for
XF-AVC clips).
[Full] Can access all 3 Browser Remote screens: [
v
] (main recording screen), [ ] (metadata screen) and
[ ] (basic screen).
[Camera] Can access only the [
v
] (main recording) screen. This would be the main operator controlling the
camera.
[Meta] Can access only the [ ] (metadata) screen. This would be the person in charge of keeping the
XF-AVC clip information up to date.
1 Open the Browser Remote’s settings submenu.
Setup screen: [NETWORK] > [Browser Remote] > [OPTIONS]
Monitoring menu: [System Setup] (
B
) > [Network Settings] > [Browser Remote]
171
Browser Remote: Controlling the Camera from a Network Device
2 Select the number of Browser Remote users.
[Users Settings] > [One User (Full Control)] or [Two Users (Camera/Meta)] > press SET
If you selected [One User (Full Control)], perform steps 3 and 4 for the [Full] user. If you selected [Two Users
(Camera/Meta)], repeat steps 3 and 4 twice, once for the [Camera] user and once for the [Meta] user.
3 Change the user name.
Setup screen: [Full: User Name] / [Camera: User Name] / [Meta: User Name] > [EDIT]
Monitoring menu: [Full: User Name] / [Camera: User Name] / [Meta: User Name] > [Input] > Press SET
Enter the desired text using the keyboard screen (A 37).
4 Change the default password.
Setup screen: Select [Full: Password] / [Camera: Password] / [Meta: Password] and press SET.
Monitoring menu: [Full: Password] / [Camera: Password] / [Meta: Password] > [Input] > Press SET
Enter the desired text using the keyboard screen (A 37).
NOTES
NOTES
The user names for the three different users cannot be the same.
Starting Browser Remote
After connecting the camera to the network, you can start the Browser Remote application on the Web browser*
of any network device** connected to the same network.
* A Web browser that supports JavaScript and is enabled to accept cookies is required.
** For details about compatible devices, operating systems, Web browsers, etc., please visit your local Canon Web site.
Preparations on the camera
1 Activate Browser Remote on the camera.
Setup screen: [NETWORK] > [Browser Remote] > [ACTIVATE] (set it to [On])
Monitoring menu: [System Setup] (w) > [Network Settings] > [Browser Remote] > [Activate] >
[On]
With Camera Access Point connections, the camera will start functioning as a wireless access point. With
Ethernet connections, connect the camera to the desired network.
and the connection type icon will appear on the HOME screen and at the top left of the monitoring
screen. When the icons turn white, the camera is ready to accept commands from the Browser Remote
application.
2 If necessary, you can check the network settings while Browser Remote is activated.
Setup screen: [NETWORK] > [Browser Remote]
Monitoring menu: [System Setup] (w) > [Network Settings] > [Browser Remote] > [Display Info]
Turn the SELECT dial to check all the settings. You will need the camera’s SSID (network name) and
password to connect a Wi-Fi device using a Camera Access Point connection. You will need the camera’s
URL and user names/passwords for the Browser Remote users to use the Browser Remote application.
Only default passwords are displayed. Passwords set by the user will not be displayed (the information
screen will show only whether a password is set or not).
On the connected network device
1 Connect the network device to the camera.
With Camera Access Point connections, select the camera’s SSID (network name) in the Wi-Fi settings.
With Ethernet connections, connect the device to the same access point as the camera.
2 Start the Web browser on the network device.
Browser Remote: Controlling the Camera from a Network Device
172
3 Enter the camera’s URL exactly as shown on the Browser Remote
information screen.
4 Enter the user name and password.
Be sure to log in with the user name and password of one of the users that
were set on the camera (A 170). If necessary, consult the administrator
who configured the camera’s settings.
The Browser Remote screen will appear. The screen displayed will differ
depending on the user information used to log in.
While Browser Remote is correctly connected to the camera, the network
connection indicator’s will turn on one by one and then turn off in an
endless loop.
The camera’s ID and lens information will appear on the Browser Remote
screen while live view is not activated.
5 Select the language for Browser Remote.
Click/touch [
H
] and select the desired language from the list. Most buttons and
controls emulate physical controls on the camera and are labeled in English only,
regardless of the language selected.
6 Use the Browser Remote controls to operate the camera.
Descriptions of the controls are given in the following pages. Detailed operation is given
in each function’s reference page.
7 When you have finished using Browser Remote, turn it off on the camera
Setup screen: [NETWORK] > [Browser Remote] > [ACTIVATE] (set it to [Off])
Monitoring menu: [System Setup] (
B
) > [Network Settings] > [Browser Remote]
> [Activate] > [Off]
The network icons will turn yellow and then disappear from the HOME screen and monitoring screen and
the connection with the application will be terminated.
Example of the login screen. The
screen may differ depending on the
Web browser and version used.
Language selection
Camera ID and lens
information
Network connection
indicator
Screen selection tabs appear only for the [Full] (full control) user
173
Browser Remote: Controlling the Camera from a Network Device
NOTES
NOTES
The live view image will not be displayed in Browser Remote in the following cases.
- While color bars are displayed on the camera.
- When [F. ASSIST.] > [OPTIONS] > [Magnification] > [Available While Rec] is set to [On].
Depending on the network used and the strength of the Wi-Fi signal (for Wi-Fi connections), you may notice
delays in the refreshing of the live view image and other settings.
Using Browser Remote
The Browser Remote application has 3 screens: [
v
] the main screen for controlling the camera remotely in
recording mode, [ ] the metadata screen, and [ ] a basic screen that allows users only to start/stop recording
using a smartphone or other device with a small screen. The screen displayed will differ depending on the user
information used to log in.
The following sections explain how to use the Browser Remote controls. For detailed information and applicable
restrictions about the functions themselves, please refer to each function’s explanation.
NOTES
NOTES
Browser Remote does not support multi-touch gestures.
The Main Remote Recording Screen [
v
]
* [Full]/[Camera] users only.
When using a computer, tablet and other devices with larger screens, this screen offers all the controls available
for operating the camera remotely via Browser Remote.
* Onscreen display/indication only. The content or value cannot be changed using Browser Remote.
768
10
*
119121413
*
1
*
3
4
2
*
5
Browser Remote: Controlling the Camera from a Network Device
174
1 Live view screen
Shows the camera’s live view image. When the live view image is not turned on, the camera ID and lens
information will appear here.
2 Status indicators
3 [LIVE VIEW] button
Touch the button to display the camera’s live view image on the Browser Remote screen.
4[
D
Touch Focus] button
Touch the button to unlock (enable) the touch focus mode.
5 Clip marks buttons
When recording, you can tag important clips by adding clip marks (A 117).
To add a clip mark
: After recording a clip, touch [ Mark] to add an
$
mark to the clip, or [ Mark] to add
a
%
mark to the clip. When the [OK Mark] or [CHECK Mark] message appears, touch .
6 Browser Remote screen selection ([Full] user only)
Tou c h [
v
] to open the main remote recording screen, [ ] to open the metadata screen (A 180) or [ ] to
open the basic screen for devices with a small screen (A 179).
7 Language selection
Changes the language used for controls in the [ ] (metadata input) screen and for error messages. Still,
most of the application’s controls emulate physical buttons on the camera and appear in English only,
regardless of the language selected.
8 Key lock button
Touch the icon to lock the Browser Remote screens in order to prevent settings from being changed
inadvertently.
9 [REC] button
Touch the button to start recording. While recording, the center of the button turns red.
Touch the button again to stop recording.
10 Recording media selection and approximate remaining recording time
The currently selected CFast card is indicated with a
Ð
mark next to the icon.
Remaining recording times are approximate and calculated based on the current video configuration used.
11 [SLOT SELECT] button
Touch the button to select the other CFast card when both CFast card slots contain a CFast card.
12 Current camera settings
This panel displays an overview of the camera settings currently used. You can change camera settings with
the controls in the detailed camera settings panel (14) on the right.
: Wi-Fi connection indicator. While Browser Remote is correctly connected to the camera, the
dots will keep turning on and off in a loop.
STBY, etc. : Recording operation (same as on the camera, A 57).
STBY
`
, REC
`
: Output recording command (A 193).
4
: Appears during double slot recording (A 52).
DC IN 00.0V,
BATT 00.0V:
Camera’s power source (DC IN and battery) (A 26). The power source currently in use is
indicated with a
Ð
mark.
[ND]: ND filter [WB]: White balance
[ISO]/[Gain]: ISO speed or gain value [Iris]: Aperture (F value or T value)
[AE]: AE shift [Shutter]: Shutter speed
175
Browser Remote: Controlling the Camera from a Network Device
13 Time code (same as on the camera)
14 Detailed camera settings panel (A 175)
Touch one of the tabs at the bottom to select the camera settings you wish to adjust:
The Main Remote Recording Screen: Detailed Camera Settings
The following sections explain how to use the controls in the detailed camera settings panel. For detailed
information and applicable restrictions about the functions themselves, please refer to each function’s
explanation.
To change the white balance
Touch the [White Balance] tab in the detailed camera settings panel.
1 Auto white balance button
Touch [ ] to set the camera to auto white balance (AWB) mode.
2 Custom white balance buttons
Touch [
Å
A] or [
Å
B].
To register a custom white balance
: Point the camera at a gray card or
white object with no pattern so it fills the center of the monitoring/live
view screen and touch [
Å
]. Use the same lighting conditions you plan
to use when recording.
During the procedure, the icon in the button will flash quickly. When it
stops flashing, the procedure is completed and the custom white
balance will be applied.
3 Preset and user-set white balance settings
Touch a button to apply the corresponding white balance settings as
shown in the button.
4 [AWB Lock] button
When auto white balance is activated, touch the button to lock the current white balance settings and keep
them when you change the subject.
To adjust the color temperature or color compensation (CC) value
Select a white balance setting other than [ ], [
Å
A] or [
Å
B].
1 Touch the right part of the white balance button (current color temperature and CC value).
2 Touch the [K] tab (color temperature) or [CC] tab (color compensation value) and select the desired value from
the list.
If necessary, repeat this step to adjust the other setting.
[White Balance]: White balance mode and related settings.
[Exposure]: Exposure related settings –aperture, shutter speed and ISO/speed gain–.
[Focus]: Focus related settings.
[Zoom]: Zoom operation (only when using a compatible lens) (A 240).
1
4
2
3
Browser Remote: Controlling the Camera from a Network Device
176
To change exposure related settings
Touch the [Exposure] tab in the detailed camera settings panel.
1 ND Filter buttons
To use the extended ND range options (8 or 10 stops), touch [Extended
Range].
Touch [–] or [+] to change the density of the ND filter (displayed above
the buttons). You can also touch the current ND filter setting and select
the desired setting from a list of options.
2 Aperture related buttons (only when using a compatible lens, A 240)
To let the camera adjust the aperture automatically, touch [Manual] and
select [Automatic] instead. No further settings are necessary.
To adjust the aperture manually, select [Manual] and use the aperture-
related controls as described below.
To change the adjustment increment, touch [1/3] and select the desired
iris increment ([1/2], [1/3], [1/2 Fine] or [1/3 Fine]). With [1/2 Fine] or [1/3
Fine] you can use the smallest aperture increment allowed by the lens.
(However, the aperture value displayed will be the closest value in the selected increment scale.)
Touch [–] or [+] to change the aperture value (displayed above the buttons). You can also touch the current
aperture value and select the desired value from a list of options.
Only when using a compatible EF Cinema lens: To display the aperture values as T values instead of F
values, touch [F] and the select [T]. Select [F] to return the display to F values.
NOTES
During manual aperture adjustment, you can also touch [PUSH AUTO IRIS] to have the camera adjust the
aperture automatically once. (The manual aperture buttons will not be available at this time.)
The aperture cannot be adjusted in the following cases.
- When using a broadcast lens.
- When using a CN7x17 KAS S/P1 or CN20x50 IAS H/P1 lens.
- When using an EF Cinema lens with an optional extender.
3 ISO speed/Gain related buttons
ISO speeds are displayed by default. To adjust the gain instead, touch [ISO] and select [Gain].
To use the ISO speeds/gain values in the extended range, touch [Extended Range].
To change the adjustment increment, touch [1/3] (ISO speed) or [Normal] (gain) and select the desired ISO
increment ([1/3] or [1]) or gain increment ([Normal] or [Fine]).
Touch [–] or [+] to change the ISO speed/gain value (displayed above the buttons). You can also touch the
current ISO speed/gain value and select the desired value from a list of options.
4 Shutter speed related buttons
To change the shutter speed mode, touch [Angle] and select the desired shutter speed mode ([Speed]
(standard shutter speed), [Angle], [Clear Scan], [Slow] (slow shutter speeds), or [Off]).
To change the adjustment increment if you selected [Speed], touch [1/3] and select the desired increment
([1/3] or [1/4]).
Touch [–] or [+] to change the shutter speed (displayed above the buttons). You can also touch the current
shutter speed value and select the desired value from a list of options. You can also change the shutter
speed mode with the tabs at the top of the list of shutter speed values.
5 AE shift buttons
Touch [AE Shift –] or [AE Shift +] to change the AE shift level.
5
2
1
2
3
4
177
Browser Remote: Controlling the Camera from a Network Device
To adjust the focus and use focus-related functions
Touch the [Focus] tab in the detailed camera settings panel. To use the following
functions, make sure that the focus mode on the lens is set to automatic
(
A 89
).
If the focus mode on the lens is set to manual, you will not be able to use
Browser Remote to control the focus. Depending on the lens used, remote
operation may not work correctly.
1 AF mode button
2 AF frame position button
Touch the button to select the position of the AF frame. Select [Center
Frame] for a fixed AF frame at the center of the live view screen, or
[Selectable] to be able to touch the live view screen to select where to
focus (A 178).
3 Face AF mode button
Touch the button to select how the camera will focus when the Face AF
function is activated and no face is detected (A 96).
4 [AF Speed] button
Touch the button to select the adjustment speed of applicable lenses when using autofocus functions.
5 [Face Detection] button
6 [Focus Guide] (Dual Pixel Focus Guide function) button
7 [ONE-SHOT AF] button (A 177) / [AF Lock] button (A 178)
8 Tracking buttons
9 Manual focus buttons
Manual focus
1 Touch the AF mode button and select [One Shot].
2 Touch one of the manual focus buttons on the [Near] side to focus closer or one of the controls on the [Far]
side to focus farther away. There are three levels of adjustment - [ ]/[ ] is the smallest and [ ]/[ ] the
largest.
Zq
Focus Guide
1 Touch the [Focus Guide] button.
2 Touch [On] to display the focus guide (A 90).
Only one focus guide frame can be displayed on the Browser Remote live screen. If the focus guide is
activated and the secondary focus guide frame is activated on the camera, the face detection and tracking
functions cannot be used.
Zq
One-shot AF
1 Touch the AF mode button and select [One Shot].
2 Touch the [ONE-SHOT AF] button.
A white AF frame will appear on the live view screen and the camera will focus automatically.
When correct focus has been achieved, the AF frame turns green. If the camera cannot focus automatically,
the AF frame will turn red.
When the AF frame position is set to [Selectable], you can touch inside the live view screen to select where
to focus (A 178).
If necessary, touch [AF Speed] to change the adjustment speed of the autofocus function.
1
2
3
4
5
6
7
8
9
Browser Remote: Controlling the Camera from a Network Device
178
Zq
AF-Boosted MF
1 Touch the AF mode button and select [AF-Boosted MF].
When the focus is in the manual adjustment range, a yellow focus frame will appear on the live view screen.
When the AF frame position is set to [Selectable], you can touch inside the live view screen to select where
to focus (A 178).
2 Touch one of the manual focus buttons to focus closer ([Near] side) or farther ([Far] side) as necessary.
When the focus enters the automatic adjustment range, the focus frame will turn white and the camera will
then finish focusing automatically.
If necessary, touch [AF Speed] to change the adjustment speed of the autofocus function.
Zq
Continuous AF
1 Touch [AF Speed] to change the adjustment speed of the autofocus function.
2 Touch the AF mode button and select [Continuous].
A white AF frame will appear on the live view screen and the camera will focus automatically.
When the AF frame position is set to [Selectable], you can touch inside the live view screen to select where
to focus (A 178).
During continuous AF mode, the [ONE-SHOT AF] button will change to [AF Lock]. Touch the [AF Lock]
button to lock the focus at its current position and frame the picture as necessary. Touch the button again to
release the AF lock.
Zq
Touching the screen to focus on a subject
You can touch on a subject that appears in the Browser Remote’s live view screen in order to select it for
focusing.
1 Touch the AF frame position button and select [Selectable].
2 Make sure the touch focus function has been unlocked and the
D
icon appears in the button (A 174).
3 Touch the desired subject in the live view screen.
Depending on the focus mode used, a frame may appear on the selected subject and the camera may also
focus on the subject automatically and even start tracking the subject.
Zq
Face AF
When the face detection function is activated, the camera will detect people’s faces and track the main subject
even when it moves. You can use face detection with one of the autofocus functions to let the camera focus on
the main subject automatically (Face AF).
1 Touch [Face Detection] and select [On].
2 If necessary, touch the Face AF mode button and select [Face Only] or [Face Priority].
A face detection frame will appear on the live view screen around all detected faces. The main subject is
indicated with arrows (
Þ
) on the sides. The camera will track the main subject as it moves.
Touch on the face of a different subject to select it as the main subject.
During continuous AF, the camera will keep focusing on the main subject’s face. During one-shot AF, the
camera will focus on the main subjects face when you touch [ONE-SHOT AF].
Zq
Tracking other subjects
In addition to Face AF, you can have the camera track other moving subjects that are not faces and also
combine the tracking function with one of the autofocus functions to let the camera focus on the desired subject
automatically.
1Touch [Tracking].
179
Browser Remote: Controlling the Camera from a Network Device
2 Touch the live view screen to select the subject you wish to track.
A tracking frame will appear on the live view screen and the camera will track the subject as it moves.
During continuous AF, the camera will keep focusing on the selected subject. During one-shot AF, the
camera will focus on the selected subject when you touch [ONE-SHOT AF].
Touch [Cancel Tracking] to select a different subject, or touch [Tracking] again to end the tracking function.
To adjust the zoom
The zoom can be adjusted only when a compatible EF Cinema lens (A 240)
is attached to the camera. Touch the [Zoom] tab in the detailed camera
settings panel.
1 Zoom slider
Drag the zoom slider up/down to zoom in [
T
] or out [
W
], respectively.
NOTES
NOTES
If you operate the zoom slider slowly it may take some time until the lens
starts moving.
The Basic Screen [ ]
* [Full] users only.
When using a smartphone or other device with a smaller screen, this screen
offers only a small live image screen for final confirmation and the [REC] button
to start and stop recording.
To open the basic screen, touch the [ ] icon at the top of the Browser
Remote screen.
1
Browser Remote: Controlling the Camera from a Network Device
180
The Metadata Screen [ ]
* [Full]/[Meta] users only.
Using Browser Remote you can create, edit and transfer to the camera a metadata profile that can be
embedded with the recorded XF-AVC clips. This metadata profile includes the user memo information (clip title,
creator, location and description), as well as GPS information. For details, refer to
Using Metadata
(A 118).
To open the metadata screen, touch the [ ] icon at the top of the Browser Remote screen.
1 Clip title
Touch inside the text box and enter the desired text. To delete the text, touch [Clear All].
2 GPS information
To enter the altitude: Touch inside the [Altitude] text box and enter the desired value.
To enter the latitude
: Touch inside one of the text boxes under [Latitude] and enter (from left to right) the
degrees, minutes and seconds values. To select a southern latitude, touch [North] and select [South] instead.
To enter the longitude
: Touch inside one of the text boxes under [Longitude] and enter (from left to right) the
degrees, minutes and seconds values. To select a western longitude, touch [East] and select [West] instead.
Touch [Clear All] to delete all the GPS-related fields at once.
3 Live view screen
Shows the camera’s live view image. When the live view image is not turned on, the camera ID and lens
information will appear here.
4 [LIVE VIEW] button
Touch the button to display the camera’s live view image on the Browser Remote screen.
5 Clip’s creator
6 Recording location
7 Description of the clip
Touch inside the text box and enter the desired text. To delete the text, touch [Clear All].
981011
1
3
4
2
5
6
7
181
Browser Remote: Controlling the Camera from a Network Device
8 Status indicators
See the descriptions in the section about the [
v
] screen (A 174).
9 [ Activate] button
Touch the button to give priority to the metadata entered in this screen when recording XF-AVC clips. This
overrides the metadata read from a file saved on the SD card.
10 [Overwrite Previous] button/[Overwrite] button
While recording an XF-AVC clip: Touch [Overwrite] to send the metadata entered in this screen to the
camera, replacing any metadata that the clip being recorded might have. When the confirmation message
appears, touch .
After recording a clip an XF-AVC clip
: Touch [Overwrite Previous] to send the metadata entered in this screen
to the camera, replacing any metadata embedded in the last clip recorded. When the confirmation message
appears, touch .
11 [Apply from Next] button
Touch the button to send the metadata entered in this screen to the camera so it is embedded only with
XFHAVC clips that are recorded after the transfer. When the confirmation message appears, touch .
This option does not overwrite the metadata of clips already recorded or being recorded.
NOTES
NOTES
The metadata sent to the camera from Browser Remote will be lost in the following cases.
- If the camera was turned off.
- If the [Rec/Media Setup] > [Metadata] > [Setting] setting was changed.
Using Browser Remote ([ Activate] button), you can give priority to metadata sent from the application.
However, you cannot return the priority back to the SD card. To use a user memo file saved on the SD card
you will need to set [Rec/Media Setup] > [Metadata] > [Setting] to [SD Card] on the camera itself.
Metadata sent to the camera from Browser Remote will not be added to relay clips recorded before the switch
to the current CFast card.
IP Streaming
182
IP Streaming
When the main recording mode is set to [XF-AVC (CFast)], after you connect the camera to a network (Wi-Fi
(Infrastructure) or wired (Ethernet)), you can stream the camera’s live video and audio* over IP to a compatible IP
video decoder** connected to the network. You can use IP streaming for live broadcasts or to send a news flash
report from a location with poor network connectivity, since the configuration of streamed video is lower (so the
data to be transferred is smaller) than that of recorded clips.
* Only 2 channels. When recording main recording clips with 4 audio channels, you can select which two channels to stream over
IP.
** This can be a dedicated video transfer device or decoder software on a computer. For details about compatible decoders,
please visit your local Canon Web site.
Configuration of video streamed over IP
* Only when [Camera Setup] > [Sensor Mode] is set to [Super 35mm] or [Super 35mm (Cropped)].
Preparations
Before you can stream video over IP, you need to configure settings related to the transfer like the protocol and
port number to use. You can also select the configuration of the streamed video.
Camera and Receiver Settings
1 Configure the network connection settings.
Use an Ethernet network (A 168) or a Wi-Fi network in Infrastructure mode (A 165).
2 Open the IP streaming settings submenu.
Setup screen: [NETWORK] > [IP Streaming] > [OPTIONS]
Monitoring menu: [System Setup] (
B
) > [Network Settings] > [IP Streaming]
3 Select the video configuration for the video streamed over IP.
[Video Output Conf.] > Desired option > Press SET
4 Select the audio channels for the IP stream.
[Audio Out Channels] > [CH1/CH2] or [CH3/CH4] > Press SET
5 Select the protocol to be used.
[Protocol] > Desired option > Press SET
If you selected [RTP+FEC], complete the error correction settings with the following procedure (A 183).
If you selected [RTSP+RTP], configure the RTSP user name and password with the following procedure
(A 183). Otherwise, continue this procedure to configure the receiver’s settings.
6 Select [Dest. IP Address] and then press SET.
Enter the IP address using the keyboard screen (A 37).
Setup screen only: Press [RESET] to reset the IP address to [0.0.0.0].
7 If necessary, select [Dest. Port No.] and press SET.
Resolution, color sampling
and frame rate
Sensor mode
Streamed signal
Video
Audio format
and bit rate
Bit rate (VBR) Resolution Frame rate
3840x2160*, YCbCr 4:2:2
59.94P, 50.00P
1920x1080, YCbCr 4:2:2
59.94P, 59.94i,
50.00P, 50.00i
Super 35mm
Super 35mm (cropped)
Super 16mm (cropped)
9 Mbps 1920x1080
59.94i, 50.00i
MPEG-2 AAC 2ch
256 Kbps
4 Mbps 1920x1080
2 Mbps 1280x720 29.97P, 25.00P
1.5 Mbps
720x480 59.94i
720x576 50.00i
183
IP Streaming
Enter the port number using the keyboard screen (A 37).
Setup screen only: Press [RESET] to reset the port number to [5000].
Using the default port is recommended.
Options
[UDP]: This protocol prioritizes transfer speeds but does not guarantee the reliability/integrity of the
data. Lost or delayed IP packets are ignored.
[RTP]: Standard protocol for video/audio broadcasts over the Internet. Lost or delayed IP packets are
ignored.
[RTP+FEC]: This setting uses the RTP protocol and adds a layer of FEC error correction so the receiving
side* can recover lost or delayed IP packets. This combination is more common for broadcasts
over Wi-Fi networks.
[RTSP+RTP]: This setting uses the RTSP (real time streaming) protocol to control the streaming server
(camera) in real time and the RTP protocol for the broadcast over IP. With the RTSP protocol,
the receiver can control when to start and stop the broadcast.
* A decoder compatible with FEC error correction is required.
FEC Error Correction Settings
From the same IP streaming [Options] submenu (setup screen) or [IP Streaming] submenu (monitoring menu) as
the main procedure (A 182).
1 Select [FEC Port No.] and then press SET.
Enter the port number using the keyboard screen (A 37).
Setup screen only: Press [RESET] to reset the port number to [5002].
2 Select the FEC interval to be used.
•[FEC Interval] > Desired value > Press SET
RTSP Settings
From the same IP streaming [Options] submenu (setup screen) or [IP Streaming] submenu (monitoring menu) as
the main procedure (A 182).
1 Change the default user name for the RTSP function.
Setup screen: [RTSP: User Name] > [EDIT]
Monitoring menu: [RTSP: User Name] > [Input] > Press SET
Enter the desired text using the keyboard screen (A 37).
2 Change the default password in the same way.
Setup screen: Select [RTSP: Password] and press SET.
Monitoring menu: [RTSP: Password] > [Input] > Press SET
Streaming Video over IP
1 Connect the decoder to the network and complete any necessary configurations on the receiving
side so the decoder is ready to receive video over IP.
For details refer to the instruction manual of the decoder device or software you will use.
2 Configure the network connection settings.
Use an Ethernet network (A 168) or a Wi-Fi network in Infrastructure mode (A 165).
IP Streaming
184
3 Activate IP streaming on the camera.
Setup screen: [NETWORK] > [IP Streaming] > [ACTIVATE] (set it to [On])
Monitoring menu: [System Setup] (
B
) > [Network Settings] > [IP Streaming] > [Activate] > [On]
and the connection type icon will appear on the HOME screen and at the top left of the monitoring
screen. When the icons turn white, the camera will start streaming video over the selected network.
You can press the REC button to record clips (XF-AVC only) while streaming video.
If the main recording video configuration used does not support IP streaming, a message will appear asking
you to change the video configuration. The video configuration you select will be saved as the main
recording video configuration and will be used even after you finish IP streaming.
4 When using the [RTSP+RTP] protocol, connect the RTSP controller (IP decoder or computer) to the
camera’s IP stream. If necessary, you can check the network settings while IP streaming is activated.
Setup screen: [NETWORK] > [IP Streaming]
Monitoring menu: [System Setup] (
B
) > [Network Settings] > [IP Streaming] > [Display Info]
Turn the SELECT dial to check all the settings. You will need the IP stream’s URL and the RTSP user name
and password.
Only the default password is displayed. Passwords set by the user will not be displayed (the information
screen will show only whether a password is set or not).
5 When you have finished streaming the desired video, turn off the IP streaming on the camera.
Setup screen: [NETWORK] > [IP Streaming] > [ACTIVATE] (set it to [Off])
Monitoring menu: [System Setup] (
B
) > [Network Settings] > [IP Streaming] > [Activate] > [Off]
The network icons will turn yellow and then disappear from the HOME screen and monitoring screen.
NOTES
NOTES
Except when using the RTSP protocol, while IP streaming is activated, the camera will continue to broadcast
video and audio data over the IP network, regardless of the status of the receiver. The streamed data is not
encoded. Be careful to set up the correct IP address and test in advance that the receiving decoder can
indeed receive the signals.
Depending on the network used and the connection conditions, you may experience lost or delayed IP
packets.
IP streaming is not available in the following cases.
- When the system frequency is set to 24.00 Hz.
- When slow & fast motion recording is activated.
185
FTP File Transfer
FTP File Transfer
You can transfer sub recording clips (XF-AVC Proxy) from the camera to another device connected to the
network, using the FTP protocol.
The following explanations assume that the FTP server is on, ready and correctly configured.
Preparations
Before you can transfer XF-AVC Proxy clips to a connected device, you need to configure the FTP server
settings and other settings related to the handling of folders and files. If necessary, consult the network
administrator in charge of the FTP server.
FTP Server and Transfer Settings
1 Configure the network connection settings.
Use an Ethernet network (A 168) or a Wi-Fi network in Infrastructure mode (A 165).
2 Open the FTP transfer settings submenu.
Setup screen: [NETWORK] > [FTP Transfer]* > [OPTIONS]
Monitoring menu: [System Setup] (
B
) > [Network Settings] > [FTP Transfer]
* The camera will switch automatically to playback mode when you select [FTP Transfer].
3 Enter the destination FTP server.
Setup screen: [FTP Server] > [EDIT]
Monitoring menu: [FTP Server] > [Input] > press SET
Enter the FTP server’s IP address or host name using the keyboard screen (A 37).
4 Enter the [FTP: User Name], [FTP: Password], and [Destination Folder] in the same way.
5 Select [Port No.] and press SET to change the port number.
Enter the port number using the keyboard screen (A 37).
Setup screen only: Press [RESET] to reset the port number to [21].
6 Select whether to activate the passive mode.
[Passive Mode] > [On] or [Off] > Press SET
[Off] is the standard setting for most cases. [On] (passive mode) is more appropriate for FTP transfers within
a network behind a firewall.
7 Select whether to create a new folder for every transfer date.
[New Folder by Date] > [On] or [Off] > Press SET
8 Select how to handle file transfers when a file with the same name already exists on the server.
[Same Named Files] > Desired option > Press SET
Options for [New Folder by Date]
[On]: A new subfolder under the transfer destination folder “YYYYMMDD\HHMMSS” will be created
for every transfer operation.
[Off]: All the files will be transferred to the folder set as [Destination Folder] in the FTP server settings.
Options for [Same Named Files]
[Skip]: If a file with the same name already exists in the destination folder, the file will not be transferred.
[Overwrite]: Even if a file with the same name already exists in the destination folder, the file will be
transferred, overwriting any file with the same name in the destination folder.
FTP File Transfer
186
Transferring Clips (FTP Transfer)
After connecting the camera to a network (Wi-Fi (Infrastructure) or wired (Ethernet)), you can transfer to the FTP
server, XF-AVC Proxy clips recorded on the SD card.
1 Open the PLAY screen for sub recordings (XF-AVC Proxy) on the SD card.
[PB MEDIA] > [SD Card (XF-AVC)]
2 Open the clip selection screen.
[OPTIONS] > [FTP Transfer]
The last XF-AVC Proxy clip recorded will be selected.
3 Select all the XF-AVC Proxy clips you wish to transfer.
Turn the SELECT dial to select a clip. Press SET to mark a clip for transfer (a check mark will appear next to
the clip name). Press SET again to remove the check mark.
You can press [SELECT ALL] to mark all the clips for transfer, or [CLEAR] to remove the check marks from
all the clips marked for transfer.
4 Once you have selected all the desired clips, press [OK].
All the applicable clips will be transferred to the FTP server. When using an Ethernet connection, the
(Ethernet) access indicator will flash quickly while the files are being transferred.
Press [CANCEL] to cancel the transfer while it is in progress.
5 When the confirmation message appears, press [OK].
IMPORTANT
Observe the following precautions when transferring files. Failing to do so may interrupt the transfer and
incomplete files may remain at the transfer destination.
- Do not open the SD card slot cover.
- Do not remove the power source or turn off the camera.
If incomplete files remain at the transfer destination, check the content and make sure they are safe to delete
before deleting them.
NOTES
NOTES
Depending on the access point’s settings and capabilities, it may take some time to transfer files.
You can also transfer the clip that is selected in the PLAY screen using the monitoring menu’s [System
Setup] (
B
) > [Network Settings] > [FTP Transfer] > [Activate] setting.
8
187
Camera Menus
Setup Screens and Menu Options
For details about how to select an item, refer to
Using the Menus
(A 32). For details about each function, see
the reference page. Setting options in boldface indicate default values.
Depending on the camera’s operating mode and the settings, some menu items may not be available. Such
menu items do not appear or appear grayed out in menu screens.
To skip directly to the page of a specific setup screen/menu:
Setup screens:
Camera menu/Monitoring menu:
* Monitoring menu only.
Setup screens
HOME screen
Screen button commands Setting options and additional information
[S&F FPS] Select the frame rate for slow & fast motion recording. (A 68)
[ACTIVATE] [On], [Off]
[OPTIONS] [Sensor Mode], [System Frequency], [Main Rec Format], [Frame Rate], [Resolution/Sampling],
[Bit Rate]
Main recording video configuration options. See [Sensor Mode] in the table for the [Camera Setup]
(
v
) menu (A 190) or the other corresponding settings in the table for the
[Rec/Media Setup] (
3
) menu (A 193).
[IRIS] (aperture) Select the aperture value. (A 79)
[AUTO IRIS] Press and hold to adjust the aperture automatically. (A 81)
[ND +], [ND –] Select the ND filter setting. (A 78)
[OPTIONS] [AE Shift], [AE Response], [Mode], [Iris Increment], [Fine Increment], [Iris Indicator],
[Zoom-Iris Correct.], [Extended ND Range]
See the corresponding settings under [AE] and [Iris] in the table for the [Camera Setup] (
v
) menu
(A 190).
[SHUTTER] Select the shutter angle, shutter speed or clear scan frequency. (A 74)
, Skip 10 values backward/forward.
These buttons appear only when the shutter speed mode is set to [Clear Scan]. Frequencies are
displayed in 1/2-stop increments.
[OPTIONS] [Mode], [Shutter Increment]
See the corresponding settings under [Shutter] in the table for the [Camera Setup] (
v
) menu
(A 190).
HOME screen A 187
ALT (alternative) screen A 188
TC (time code) screen A 189
PLAY screen A 190
[Camera Setup] (
v
) menu A 190
[Custom Picture] (
/
) menu* A 192
[Audio Setup] (
¡
) menu* A 192
[Rec/Media Setup] (
3
) menu A 193
[Monitoring Setup] (
¢
) menu A 194
[Assist. Functions] (
A
) menu A 196
[System Setup] (
B
) menu A 197
[My Menu]/[My Menu 1] ( ) menu A 202
Setup Screens and Menu Options
188
ALT (alternative) screen
[ISO/GAIN] Select the ISO speed or gain value. (A 76)
[OPTIONS] [Select], [Extended Range], [ISO Increment], [Gain Increment]
See the corresponding settings under [ISO/Gain] in the table for the [Camera Setup] (
v
) menu
(A 190).
[COLOR]
(preset color settings/
custom picture settings)
The screen will show the currently selected preset color setting ([Preset]) and the main
settings of the custom picture file: [Gamma], [Color Space] and [Color Matrix].
(A 84)
[CP MAIN] [Preset], [Gamma], [Color Space], [Color Matrix] (A 134)
[CP OTHERS] [Other Settings], [File]
For the custom picture settings, refer to the detailed table (A 135). For the [File] options, see the
table for the [Custom Picture] (
/
) menu (A 192).
[LUT] [MON. 1], [MON. 2], [SDI OUT 1/2/3/4], [SDI OUT 1/2], [SDI OUT 3/4], [HDMI], [VIDEO], [
8
XF-AVC]
See the corresponding settings under [LUT] in the table for the [Monitoring Setup] (
¢
) menu
(A 194).
[USER LUT] [Register], [Color Space(Output)], [Range(Output)], [Delete], [Reset All], [Rename],
[Display Info]
(A 157)
[WB] (white balance) [ AWB], [
Å
Set A], [
Å
Set B], [
¼
Daylight], [
É
Tungsten], [ USER_01],
[ USER_02], [ USER_03], [ USER_04], [ USER_05]
(A 86)
[ADJUST] Color temperature: 2,000 K to 15,000 K, Color compensation (CC): –20 to +20
[ ], [ ], [<>], [RESET], [OK] (confirm changes)
Adjust the color temperature and/or color compensation (CC) value.
[WB SET] [OK] (start the white balance calibration) (A 87)
Register a custom white balance setting.
[RENAME] Text string up to 8 characters ([USER_01] to [USER_05]) (A 88)
Rename a user-set white balance setting.
[OPTIONS] [Shockless WB], [AWB Response], [C. Temp. Increment]
See the corresponding settings under [White Balance] in the table for the [Camera Setup] (
v
) menu
(A 190).
Screen button commands Setting options and additional information
Zq
[AF] (autofocus) Focus adjustment with the SELECT dial.
[FACE] (face detection) [On], [Off]
Turn the face detection function on/off (A 96).
[TRACKING] [On], [Off]
Turn the tracking function on/off (A 97).
[ONE SHOT] Press and hold to focus automatically once. (A 92)
[AF LOCK] Lock the automatic focus on the current subject. (A 95)
[FRAME]
(move the frame)
[
Ï
], [
Ð
], [
Í
], [
Î
], [CENTER] (return the focus frame to the center)
Move the focus frame (A 95).
[OPTIONS] [AF Mode], [AF Frame Position], [AF Frame Size], [Face AF], [AF Speed],
[AF Speed Limit], [AF Response]
See the corresponding settings under [Focus] in the table for the [Camera Setup] (
v
) menu
(A 190).
Screen button commands Setting options and additional information
189
Setup Screens and Menu Options
TC (time code) screen
[F. ASSIST.] Focus adjustment with the SELECT dial.
Zq
[FACE]
(face detection)
[On], [Off]
Turn the face detection function on/off (A 96).
[MAGN.] (magnification) [On], [Off]
Turn the magnification function on/off (A 92).
[PEAKING] [On], [Off]
Turn the peaking function on/off (A 91).
Zq
[GUIDE]
(focus guide)
[On], [Off]
Turn the focus guide on/off (A 90).
[FRAME]
(move the frame)
[
Ï
], [
Ð
], [
Í
], [
Î
], [CENTER] (return the focus frame to the center)
Move the focus frame (A 95).
[OPTIONS] [Face AF], [Focus Guide], [Peaking], [Magnification]
See [Focus] > [Face AF] in the table for the [Camera Setup] (
v
) menu (A 190), or the
corresponding settings in the table for the [Assist. Functions] (
A
) menu (A 196).
[AUDIO] Audio source, audio level adjustment mode (A or M), and audio level meter for audio
channels CH1 to CH4
[CH1/2 IN], [CH3/4 IN]
(audio input selection)
[INPUT Terminals], [MIC Terminal], [Monaural Mic]
[REC LEVEL] [CH1] to [CH4], [CH1/CH2], [CH3/CH4], [OPTIONS]
For each channel/pair of channels: [A M] (automatic/manual audio level)
When set to [M]: Manual audio recording level: 0 to 100 (50)
(A 111)
[MONITOR] [CH1/CH2], [CH1/CH1], [CH2/CH2], [CH1+2/CH1+2], [CH3/CH4], [CH3/CH3], [CH4/CH4],
[CH3+4/CH3+4], [CH1+3/CH2+4]
(A 160)
[
×
] (headphone volume) 0 to 15 (8) (A 113)
[OPTIONS] [Audio Input], [Audio Output]
See the corresponding settings in the table for the [Audio Setup] (
¡
) menu (A 192).
[CAM LVL]
(camera’s electronic level)
[Tilt] (degree of rotation degree of rotation of the optical axis up and down), [Roll] (degree
of rotation sideways along the optical axis), [SET] (set the camera’s current position as
baseline)
(A 40)
[NETWORK] [Browser Remote], [IP Streaming], [FTP Transfer]
[Browser Remote] Current connection settings, [ACTIVATE]: [On] or [Off], [OPTIONS] (A 170)
[IP Streaming] Current connection settings, [ACTIVATE]: [On] or [Off], [OPTIONS] (A 182)
[FTP Transfer] After switching to playback mode: Clip selection screen, [OPTIONS] (A 185)
See the corresponding settings under [Network Settings] in the table for the [System Setup] (
B
)
menu (A 197).
Screen button commands Setting options and additional information
[SET TC] [<], [>] (change selected field), [RESET], [OK] (confirm changes) (A 101)
[UB] (user bit) Current user bit of the camera (A 104)
[SET UB] [<], [>] (change selected field), [RESET], [OK] (confirm changes)
[OPTIONS] [Recording Mode], [Type]
See the corresponding settings under [User Bit] in the table for the [System Setup] (
B
) menu
(A 197).
Screen button commands Setting options and additional information
Setup Screens and Menu Options
190
PLAY screen
Information about the clip/photo selected for playback and playback related functions (A 141).
Camera Menu and Monitoring Menu
[Camera Setup] (
v
) menu
[OPTIONS] [Mode], [Run], [DF/NDF], [TC In/Out]
See the corresponding settings under [Time Code] in the table for the [System Setup] (
B
) menu
(A 197).
Screen button commands Setting options and additional information
[PB MEDIA]
(playback media and format)
[CFast (XF-AVC)], [CFast (ProRes)], [ Capture Drive (ProRes)],
[ Capture Drive (RAW)], [SD Card (XF-AVC)], [SD Card (Photos)]
(A 142)
[STEP SIZE] [1 Frame], [1 sec], [10%] (1/10 of the clip’s duration) (A 142)
[CLIP LIST] List of clips, [PB MEDIA] (A 142)
[OPTIONS] [Display Clip Info], [Add
$
Mark], [Delete
$
Mark], [Add
%
Mark],
[Delete
%
Mark], [Delete], [Delete User Memo], [Copy
/
File], [Recover Clip],
[FTP Transfer]
(A 145)
Submenu levels / Menu items Setting options and additional information
[Sensor Mode] qr
[Full Frame], [Super 35mm (Cropped)], [Super 16mm (Cropped)]
Z[]
[Super 35mm], [Super 16mm (Cropped)]
(A 68)
[Light Metering] [Backlight], [Standard], [Spotlight] (A 82)
[ABB]* (A 54)
[AE]** (A 82)
[AE Shift] –2.0 to 2.0 in 0.25 point intervals (±0)
[AE Response] [High], [Normal], [Low]
Determines how quickly the aperture is adjusted during automatic exposure. This setting has no
effect when one of the following lenses is attached.
· EF Cinema lenses other than the CN-E18-80mm T4.4 L IS KAS S or CN-E70-200mm T4.4 L IS KAS
S lens
· Broadcast lenses (A 240)
[ISO/Gain]** (A 76)
[Select] [ISO], [Gain]
[Extended Range] [On], [Off]
[ISO Increment] [1 stop], [1/3 stop]
[Gain Increment] [Normal], [Fine]
[Iris]** (A 79)
[Mode] [Automatic], [Manual]
This setting is available only when a compatible lens (A 240) is attached to the camera.
[Iris Increment] [1/2 stop], [1/3 stop]
[Fine Increment] [On], [Off]
[Iris Indicator] [F], [T]
Determines whether the aperture value will be displayed on the control display and monitoring
screen in terms of F values or T values (only when using an EF Cinema lens).
Screen button commands Setting options and additional information
191
Setup Screens and Menu Options
* Camera menu only.
** Monitoring menu only.
*** The default value depends on the country/region or purchase.
[Zoom-Iris Correct.] [On], [Off]
If you are using a compatible lens, when this setting is set to [On], the camera will adjust the aperture
as needed to keep the selected aperture value while zooming. Because of this adjustment, the
brightness of the image might flicker slightly or you may hear the operation sound.
[Extended ND Range]** [On], [Off] (A 78)
[Shutter]** (A 74)
[Mode] [Speed], [Angle], [Clear Scan], [Slow], [Off]
[Shutter Increment] [1/3 stop], [1/4 stop]
[White Balance]**
[Shockless WB] [On], [Off] (A 86)
[AWB Response] [High], [Normal], [Low] (A 87)
[C. Temp. Increment] [Mired], [Kelvin] (A 86)
Zq
[Focus]**
[AF Mode] [One Shot], [AF-Boosted MF], [Continuous] (A 89)
[AF Frame Position] [Selectable], [Center Frame] (A 95)
[AF Frame Size] [Large], [Small] (A 95)
[Face Detection] [On], [Off] (A 96)
[Face AF] [Face Priority], [Face Only] (A 96)
[AF Speed] –7 to +2 (0) (A 94)
[AF Speed Limit] [Always], [Only While Recording] (A 94)
[AF Response] –3 to +3 (0) (A 94)
[Color Bars] (A 114)
[Activate] [On], [Off]
[Type] [SMPTE], [EBU]***, [ARIB]
[Mount Adapter]
Zq
[MO-4E],
[]r
[MO-4P], [Off]
When an optional MO-4E or MO-4P B4 Mount Adapter is attached to the camera, this setting
optimizes optical settings for the adapter.
[Focus Control] [Camera], [Lens]
Determines the signal path used to adjust the focus.
[Camera]: Use the default setting for most cases.
[Lens]: You can adjust the focus using an accessory connected to the lens but you will not be able to
use the camera’s autofocus functions or an optional RC-V100 Remote Controller connected to the
camera to adjust the focus.
Z[qr
[Flash Band Corr.]
[On], [Off] (A 75)
Zq
[Periph. Illum. Corr.] [On], [Off] (A 47)
[Chrom. Aberr. Corr.] [On], [Off] (A 47)
[Lens Info] (A 44)
Submenu levels / Menu items Setting options and additional information
Setup Screens and Menu Options
192
[Custom Picture] (
/
) menu (monitoring menu only)
[Audio Setup] menu (
¡
) (monitoring menu only)
Submenu levels / Menu items Setting options and additional information
[Preset], [Main Settings], [Other Settings] Refer to
Preset Color Settings
(A 84) and the
Available Custom Picture Settings
tables (A 134).
[File]
[Select] [C1:CP000001] to [C20:CP000020] (A 131)
[Rename] (A 132)
[Protect] [Unprotect], [Protect] (A 132)
[Reset] [Cancel], [OK] (A 132)
[Transfer] [Copy to 8], [Load from 8] (A 133)
Submenu levels / Menu items Setting options and additional information
[Audio Input]
[Select CH1/CH2 Input],
[Select CH3/CH4 Input]
[INPUT Terminals], [MIC Terminal], [Monaural Mic] (A 111)
[Audio Rec Level CH1] to
[Audio Rec Level CH4],
[Audio Rec Level CH1/CH2],
[Audio Rec Level CH3/CH4]
[Automatic], [Manual] (A 111)
[CH1 Level] to [CH4 Level],
[CH1/CH2 Level], [CH3/CH4 Level]
0 to 100 (50) (A 111)
[CH2 Input] [INPUT 2], [INPUT 1] (A 111)
[INPUT 1 Mic Trim],
[INPUT 2 Mic Trim]
[+12 dB], [+6 dB], [0 dB], [–6 dB], [–12 dB] (A 112)
[INPUT 1 Mic Att.],
[INPUT 2 Mic Att.]
[On], [Off] (A 113)
[INPUT 1&2 Limiter] [On], [Off] (A 111)
[MIC Att.] [On], [Off] (A 113)
[MIC Low Cut] [On], [Off] (A 113)
[CH1/CH2 ALC Link],
[CH3/CH4 ALC Link]
[Linked], [Separated] (A 111)
[1 kHz Tone] [–12 dB], [–18 dB], [–20 dB], [Off] (A 114)
[Audio Output]
[Headphone Volume] [Off], 1 to 15 (8) (A 143)
[Monitor Channels] [CH1/CH2], [CH1/CH1], [CH2/CH2], [CH1+2/CH1+2], [CH3/CH4], [CH3/CH3], [CH4/CH4],
[CH3+4/CH3+4], [CH1+3/CH2+4]
(A 160)
[HDMI Channels],
[RAW (SDI) Channels]
[CH1/CH2], [CH3/CH4] (A 160)
193
Setup Screens and Menu Options
[Rec/Media Setup] (
3
) menu
Submenu levels / Menu items Setting options and additional information
[Initialize Media] [CFast A], [CFast B], [SD Card], [ Capture Drive] (A 51, 205)
[Main Rec Format] [XF-AVC (CFast)], [ProRes (CFast)], [ProRes ( Capture Drive)],
[RAW ( Capture Drive)], [RAW (SDI OUT)]
1
(A 65, 206)
1
Available when [Camera Setup] > [Sensor Mode] is set to [Super 35mm] or [Super 35mm (Cropped)].
[Slow & Fast Motion]* [On], [Off] (A 68)
[System Frequency] [59.94 Hz], [50.00 Hz]**, [24.00 Hz] (A 65)
[Frame Rate] When [System Frequency] is set to [59.94 Hz]:
[59.94i], [59.94P], [29.97P], [23.98P]
When [System Frequency] is set to [50.00 Hz]:
[50.00i], [50.00P], [25.00P]
(A 65)
[Resolution/Sampling] When [Main Rec Format] is set to one of the CFast options:
[4096x2160 YCC 10 bit], [3840x2160 YCC 10 bit], [2048x1080 RGB 12 bit],
[2048x1080 RGB 10 bit], [2048x1080 YCC 10 bit], [1920x1080 RGB 12 bit],
[1920x1080 RGB 10 bit], [1920x1080 YCC 10 bit]
When [Main Rec Format] is set to one of the RAW options:
[5952x3140 RAW]
2
, [5952x2352 RAW]
2
, [4512x2376 RAW]
3
, [4272x2376 RAW]
4
,
[4512x1920 RAW]
3
, [4096x2160 RAW], [2048x1080 RAW]
2
(A 66)
2
qr only.
3
Z[
only.
4
]
only.
[Bit Rate] When [Main Rec Format] is set to [XF-AVC (CFast)]
5
:
[810 Mbps Intra-frame], [440 Mbps Intra-frame], [410 Mbps Intra-frame],
[360 Mbps Intra-frame], [310 Mbps Intra-frame], [225 Mbps Intra-frame],
[210 Mbps Intra-frame], [170 Mbps Intra-frame], [160 Mbps Intra-frame],
[90 Mbps Intra-frame], [50 Mbps Long GOP]
When [Main Rec Format] is set to [ProRes (CFast)]
5
:
[ProRes4444XQ] (qr), [ProRes4444], [ProRes422HQ], [ProRes422]
(A 66)
5
Most bit rate settings are set automatically by the camera according to other video configuration settings. For
details about the settings that can be selected by the user, check the tables on the reference page.
[Sub Rec (XF-AVC)] (A 71)
[Recording Media] [CFast]
6
, [SD Card], [Off]
6
Only when [Main Rec Format] is set to one of the RAW options.
[Resolution/Sampling] [4096x2160 YCC 10 bit], [3840x2160 YCC 10 bit], [2048x1080 YCC 10 bit], [1920x1080 YCC 10 bit]
[Apply LUT]* [BT.709], [BT.2020], [DCI], [Off]
[Double/Relay Rec] (A 52)
[Double Slot Rec], [Relay Recording] [On], [Off]
[Rec Command] [On], [Off]
When you connect the camera to an external recorder, if you start or stop recording with the camera,
the other device will also start or stop recording.
[Metadata]
[Camera Index] [A] to [Z] (A 62)
[Reel Number], [Clip Number] [001] to [999] (A 62)
[User Defined] User defined string up to 5 characters ([CANON]) (A 62)
[Scene], [Take] Scene description up to 16 characters / Take description up to 8 characters (A 119)
[Lens Squeeze] [x2.0], [x1.3], [Off] (A 122)
[Setting] [Remote], [SD Card] (A 118, 180)
[User Memo] [Off], list of user memo files available on the SD card (A 118)
Setup Screens and Menu Options
194
* Monitoring menu only.
** The default value depends on the country/region or purchase.
[Monitoring Setup] (
¢
) menu
[Country Code], [Organization],
[User Code]
Identifiers up to 4 characters ([00__] default for [Organization] only)
[Country Code]: This identifier is the country code defined by ISO-3166-1 and is to be entered
starting from the left.
[Organization]: This identifier represents the organization that owns or operates the camera and can
be obtained by registering with the SMPTE Registration Authority. If the organization is not
registered, enter [0000].
[User Code]: This identifier designates the user. Leave this blank if [Organization] is set to [0000].
[Add / File] [On], [Off] (A 133)
[Clip Numbering] [Reset], [Continuous] (A 63)
[Photo Numbering] [Reset], [Continuous] (A 125)
Submenu levels / Menu items Setting options and additional information
[Control Display] (A 31)
[Camera]
[Brightness] 1 to 5 (3)
[Turn Off Display] [Assignable Buttons], [Auto (Remote OU-700)]
[Remote OU-700]
[Brightness] 1 to 5 (3)
[EVF-V70]* (A 42)
[Brightness], [Contrast] –99 to 99 (±0)
[Color] –20 to 20 (±0)
[Sharpness] 1 to 4 (2)
[Luminance] [Normal], [High]
[Eye Sensor] [On], [Off]
When this setting is set to [On], the optional viewfinder will be dimmed automatically when the
sensor does not detect the user’s eye near the eyepiece for 30 seconds (or 10 seconds, in playback
mode).
[Surrounding Area]
[Activate] [On], [Off]
When this setting is set to [On], the image from the camera will be reduced and some of the
surroundings around the recorded frame will be shown on the shooting screen. qr
Available only when [Camera Setup] > [Sensor Mode] is set to [Super 35mm (Cropped)]
or [Super 35mm].
[Select] [Line], [Mask 25%], [Mask 50%], [Mask 75%]
You can use a color line or apply masking to the non-recorded areas to distinguish the area covered
by the recorded frame from the surroundings. If you selected [Line], you can select the color of the
border line with the [Line Color] setting.
[Line Color] [Yellow], [Blue], [Green], [Red], [Black], [Gray], [White]
[Anamorphic] (A 122)
[Desqueeze Ratio] [Lens Squeeze Factor], [x2.0], [x1.3]
[VIDEO Output],
[MON.+HDMI Output]
[On], [Off]
Submenu levels / Menu items Setting options and additional information
195
Setup Screens and Menu Options
[LUT]* (A 155)
[MON. 1], [MON.2],
[SDI OUT 1/2/3/4], [SDI OUT 1/2],
[SDI OUT 3/4], [HDMI]
[BT.709], [BT.2020], [DCI], [ACESproxy], [HDR-PQ], [HDR-HLG], [UserLUT1] to
[UserLUT4]
1
, [Off]
[VIDEO] [BT.709], [HDR 1600%], [HDR 400%], [UserLUT1] to [UserLUT4]
1
, [Off]
1
Available only when user LUTs have been registered in the camera.
[User LUT] [Register], [Color Space(Output)], [Range(Output)], [Delete], [Reset All], [Rename],
[Display Info]
(A 157)
[B&W Image]
[VIDEO Output],
[MON.+HDMI Output]
[On], [Off]
When this setting is set to [On], the live image from the camera displayed on the optional viewfinder
(VIDEO terminal) or on an external monitor (MON. terminals or HDMI OUT terminal) to black & white. If
enabled, onscreen displays will appear in color.
[OSD Output] (A 154)
[VIDEO]
[Output] [On], [Off]
[Peripheral Border] [On], [Off]
[MON.+HDMI]
[Output] [On], [Off]
[Peripheral Border] [On], [Off]
[Displayed Units] [Meters], [Feet]**
Changes the distance units used in camera displays between meters and feet.
[Custom Display 1] (A 139)
[Light Metering],
[Custom Picture], [Focal Length],
[ND Filter], [Focus Mode],
[Key Lock], [White Balance],
[Exposure], [Iris], [ISO/Gain],
[Shutter], [Peaking], [Magnification],
[LUT], Zq[Lens],
[Mount Adapter],
Z[q
r
[Flash Band Corr.]
[On], [Off]
[Custom Display 2] (A 139)
[DC IN / Battery],
[Remaining Rec Time]
[Only Warnings], [Normal], [Off]
[Recording Mode], [Genlock],
[Time Code], [Camera Index],
[Reel/Clip Number]
[On], [Off]
[Remaining Photos] [Only Warnings], [Normal], [Off]
[Temperature/Fan],
[Frame Rate], [OSD Output],
[Rec Command], [Level],
[Audio Lvl Indicator],
[Network Functions], [GPS]
[On]
2
, [Off]
2
However, the default for [OSD Output] and [Level] is [Off].
[On], [Normal]: Show the icon/onscreen display always or whenever the necessary conditions are
triggered.
[Only Warnings]: Show the icon/onscreen display only when a critical level is reached.
Submenu levels / Menu items Setting options and additional information
Setup Screens and Menu Options
196
* Monitoring menu only.
** The default value depends on the country/region of purchase.
[Assist. Functions] (
A
) menu
[Custom Display] (A 139)
[Camera Index],
[Audio Lvl Indicator]
[On], [Off]
[Date/Time], [Camera Data] [On], [Off]
These settings are available only when the menu is opened from the PLAY screen (A 144) and
determine whether the following onscreen displays will appear on the playback image.
[Camera Index]: The identifier of the camera used to shoot the clip/photo.
[Audio Lvl Indicator]: The audio level meter (clips only).
[Date/Time]: The date and time when the clip/photo was recorded.
[Camera Data]: The aperture value, shutter speed and ISO speed/gain value used to record the clip
(clips only).
Submenu levels / Menu items Setting options and additional information
Zq
[Focus Guide]* (A 90)
[Activate] [On], [Off]
[Display 2nd Frame] [On], [Off]
[Peaking]* (A 91)
[VIDEO Output],
[MON.+HDMI Output]
[On], [Off]
[Select] [Peaking 1], [Peaking 2]
[Peaking 1]
[Color] [White], [Red], [Yellow], [Blue]
[Gain] [Off], 1 to 15 (8)
[Frequency] 1 to 4 (2)
[Peaking 2]
[Color] [White], [Red], [Yellow], [Blue]
[Gain] [Off], 1 to 15 (15)
[Frequency] 1 to 4 (1)
[Focus Assist. B&W] [On], [Off]
[Magnification]* (A 92)
[Available While Rec] [On], [Off]
[VIDEO Output],
[MON.+HDMI Output]
[On], [Off]
[Focus Assist. B&W] [On], [Off]
[False Color] (A 100)
[VIDEO Output], [MON.1 Output],
[MON.2 Output], [HDMI Output]
[On], [Off]
[Color Index]
[Zebra] (A 99)
[VIDEO Output],
[MON.+HDMI Output]
[On], [Off]
[Select] [Zebra 1], [Zebra 2], [Zebra 1+2]
[Zebra 1 Level] [5 ±5%] to [95 ±5%] in 5 percentage point intervals ([70 ±5%])
[Zebra 2 Level] 0% to 100% in 5 percentage point intervals (100%)
Submenu levels / Menu items Setting options and additional information
197
Setup Screens and Menu Options
* Monitoring menu only.
[System Setup] (
B
) menu
[Waveform Monitor] (A 115)
[VIDEO Output],
[MON.+HDMI Output]
[On], [Off]
[Position] [Right], [Left]
[Type] [Line], [Line+Spot], [Select Line], [Field], [RGB], [YPbPr]
[Gain] [1x], [2x]
[Y Position] [0%], [15%], [30%], [45%], [50%]
[Select Line] 0 to 1079 in 1-line increments (540),
0 to 2158 in 2-line increments (1080),
0 to 2530 in 2-line increments (1266),
0 to 3138 in 2-line increments (1570)
Available options depend on the camera model, resolution and operating mode (recording or
playback mode).
[Markers] (A 98)
[VIDEO Output],
[MON.+HDMI Output]
[On], [Off]
[Center], [Horizontal], [Grid],
[Aspect Marker]
[Yellow], [Blue], [Green], [Red], [Black], [Gray], [White], [Off]
[Aspect Ratio] [4:3], [13:9], [14:9], [16:9], [1.375:1], [1.66:1], [1.75:1], [1.85:1], [1.90:1], [2.35:1],
[2.39:1], [Custom]
[Custom Ratio] 1.00:1 to 9.99:1 (1.00:1)
[Safe Area] [Yellow], [Blue], [Green], [Red], [Black], [Gray], [White], [Off]
[Basis for Safe Area] [Whole Picture], [Selected Aspect Marker]
[Safe Area %] [80%], [90%], [92.5%], [95%]
[Sub Rec Area] [Yellow], [Blue], [Green], [Red], [Black], [Gray], [White], [Off]
Submenu levels / Menu items Setting options and additional information
[Reset] [All Settings], [Assignable Buttons], [Level]
These settings reset the following camera settings to default values/settings.
[All Settings]: All the camera’s settings except for the hour meter.
[Assignable Buttons]: Only the assignable buttons.
[Level]: Only the camera’s level (electronic horizon).
[Transfer Menu//] (A 140)
[Save] [To Camera], [To 8]
[Load] [From Camera], [From 8]
[Set Clock] (A 29)
[Date/Time]
[Date Format] [YMD], [YMD/24H], [MDY], [MDY/24H], [DMY]**, [DMY/24H]
[Time Zone] List of world time zones ([UTC-05:00 New York] or [UTC+01:00 Central Europe])**
[Language] [Deutsch], [English], [Español], [Français], [Italiano], [Polski], [Português], [ ],
[ ], [ ], [ ]
(A 29)
[Term. Output Setup]
[HDMI Max Res.] [4096x2160 / 3840x2160], [1920x1080] (A 154)
[MON. Output] [2048x1080 / 1920x1080], [1920×1080], [Off] (A 153)
[SDI OUT Output] [On], [Off] (A 152)
Submenu levels / Menu items Setting options and additional information
Setup Screens and Menu Options
198
[3G-SDI Mapping] [Level A], [Level B] (A 152, 153)
[GENLOCK/SYNC OUT]
[Terminal Function] [HD Sync Output], [Genlock Input] (A 105)
[Genlock Adjustment] –1023 to +1023 (000) (A 106)
The phase difference between the external Genlock signal and the camera is initially set to 0. This
setting allows you to adjust it within the range of approx. ±0.4 H (–1023 to 1023). To set a 4-digit
adjustment value, set the first field to 10 or –10.
[SYNC Scan Mode] [P], [PsF] (A 107)
[Time Code]* (A 101)
[Mode] [Preset], [Regen.]
[Run] [Rec Run], [Free Run]
[DF/NDF] [DF], [NDF]*
[Setting] [00:00:00:00] to [23:59:59:29] (for 59.94 Hz recordings),
[23:59:59:24] (for 50.00 Hz recordings) or [23:59:59:23] (for 24.00 Hz recordings)
[TC In/Out] [In], [Out] (A 106, 107)
[User Bit]* (A 104)
[Recording Mode] [Internal], [External]
[Type] [Setting], [Time], [Date]
[REMOTE Term.] [RC-V100 (REMOTE B)], [RC-V100 (REMOTE A)], [Standard] (A 123)
[Assignable Buttons] Following are the default settings for each assignable button. For a complete list of the functions that
can be assigned, refer to the detailed table (A 128).
[Camera] 1: [Magn.: MON.+HDMI], 2: [Peaking: MON.+HDMI], 3: [False Color: MON.+HDMI],
4: [WFM: MON.+HDMI], 5: [One-Shot AF]
[1] to [5]
[EVF-V70] 1: [FUNC], 2: [EVF-V70 Setup], 3: [Magn.: VIDEO], 4: [False Color: VIDEO]
[1] to [4]
[Grip SG-1] 1: [One Shot AF]
[1]
[Remote RC-V100] 1: [Magn.: MON.+HDMI], 2: [Peaking: MON.+HDMI], 3: [False Color: MON.+HDMI],
4: [Waveform Monitor]
[1] to [4]
[CUSTOM Switch] (A 77, 80)
[1] [Iris], [ISO/Gain], [Off]
[2] [Iris], [ISO/Gain], [Off]
[Control Dial Dir.]
[Camera], [Grip SG-1] [Reverse], [Normal]
Changes the direction of the adjustment when operating the control dial on the camera or on an
optional SG-1 Shoulder Style Grip Unit attached to the camera, respectively.
[SELECT Dial Dir.]
[Camera], [Remote OU-700],
[EVF-V70]
[Reverse], [Normal]
Changes the direction of the adjustment when operating the SELECT dial on the camera, or on an
optional OU-700 Remote Operation Unit or optional EVF-V70 OLED Electronic Viewfinder attached to
the camera, respectively.
[C Button] [Linked], [Separated] (A 56)
When an optional OU-700 Remote Operation Unit is connected to the camera, this setting determines
if the
C
buttons on the camera and the OU-700 lock only local controls ([Separated]) or if either will
lock all the controls, both on the camera and on the OU-700 ([Linked]).
Submenu levels / Menu items Setting options and additional information
199
Setup Screens and Menu Options
[Key Lock] [All Buttons], [All Except REC Button]
Selects whether to lock all buttons (including REC buttons) or all buttons with the exception of
currently enabled REC buttons).
[REC Button]
[Control Display Side], [Front],
[Media Slot Side], [Grip SG-1],
[Remote OU-700]
[Disable], [Enable]
Independently enables or disables the use of individual REC buttons on the camera (on the left side
next to the control display, on the front, or on the right side next to the card slots), or on an optional
SG-1 Shoulder Style Grip Unit or optional OU-700 Remote Operation Unit attached to the camera.
[ND FILTER Button] [Disable], [Enable] (A 78)
[LED]
[Button Illumination]
[Camera/EVF-V70],
[Remote OU-700]
[High], [Low], [Off]
[Tally Lamp]
[Camera], [Remote OU-700] [On], [Off]
[Media Access], [LAN (Ethernet)] [On], [Off]
These settings determine whether the following LEDs and indicators will illuminate.
[Button Illumination]: Controls the illumination of physical buttons on the camera or on an optional
OU-700 Remote Operation Unit connected to the camera. Buttons that illuminate when you select
an option other than [Off] are indicated in the
Names of Parts
(A 13).
[Tally Lamp]: The tally lamp on the camera or on an optional OU-700 Remote Operation Unit
connected to the camera. Note that regardless of this setting, when the camera is turned off, the
tally lamps will illuminate in red momentarily after the Q button is pressed.
[Media Access]: The CFast card access indicators and SD card access indicator when the camera is
accessing the respective recording media.
[LAN (Ethernet)]: The (Ethernet) indicator when the camera is accessing a wired network.
[Fan] (A 64)
[Mode] [Automatic], [Always On]
[Fan Speed (STBY)] [Maximum], [High], [Middle], [Low]
[Fan Speed (REC)],
[Fan Speed (Always)]
[High], [Middle], [Low]
[Fan Speed] [High], [Middle], [Low]
[Low Power Warning] (A 27)
[Battery (%)] 1% to 10% (5%)
[Battery (V)], [DC IN (V)] 12.0 V to 15.0 V in 0.1 V intervals (13.0 V)
[Rec Operation Beep] [Start and Stop], [Stop Only], [Start Only], [Off]
[Scan Reverse Rec]
[Setting] [Both], [Vertical], [Horizontal], [Off]
Inverts the recorded image horizontally and/or vertically. Not available during RAW video recording/
output.
[3D Rec Mode] [On], [Off]
When using another C700 / C700 PL / C700 GS PL / C700 FF / C700 FF PL camera to shoot in 3D, this
function corrects lags in the video and audio signals output from the SDI OUT or MON. terminals.
When using a C700 / C700 PL / C700 GS PL camera with a C700 FF / C700 FF PL camera, the
correction applies only to signals output from the SDI OUT terminal.
[Level Sensitivity] [x16], [x8], [x4], [x2], [Standard]
Adjusts the sensitivity of the camera's level (electronic horizon).
[Network Settings]*
[Browser Remote] (A 170)
Submenu levels / Menu items Setting options and additional information
Setup Screens and Menu Options
200
[Display Info]
[Activate] [On], [Off]
[Connection Method] [Camera Access Point], [Ethernet]
[SSID] Network name up to 32 characters (Z[]
[C700-xxxx-xx_Canon0C], qr [C700FF-xxxx-xx_Canon0C])
[Frequency] [5 GHz], [2.4 GHz]
[Channel] Available Wi-Fi channels depend on the model of wireless file transmitter used. For
details, refer to the “Areas of Use and Restrictions” leaflet supplied with the optional
WFT-E6 or WFT-E8 Wireless File Transmitter. (Default channel is [1])
[Authn/Encr Method] [WPA2-PSK/AES], [Open/No encryption]
[Password] [12345678]
[IP Address Assign.] [Automatic], [Manual]
[IP Address] 0.0.0.0 to 255.255.255.255 ([192.168.0.80])
[Subnet Mask] 0.0.0.0 to 255.255.255.255 ([255.255.255.0])
[Default Gateway] 0.0.0.0 to 255.255.255.255 ([0.0.0.0])
[Port No.] 1 to 65535 ([80])
[Camera ID] Camera identifier up to 8 characters (Z[] [C700],
qr [C700FF])
[Users Settings] [One User (Full)], [Two Users (Camera/Meta)]
[Full: User Name],
[Camera: User Name],
[Meta: User Name]
User name up to 8 characters (Default user names are [Full], [Camera] and [Meta],
respectively)
[Full: Password],
[Camera: Password],
[Meta: Password]
Password up to 8 characters ([12345678])
[Check MAC Address]
Displays the MAC address when the camera is connected to a wired (Ethernet) network or when an
optional wireless transmitter is attached.
[IP Streaming] (A 182)
[Display Info]
[Activate] [On], [Off]
[Connection Method] [Ethernet], [Infrastructure]
[Wi-Fi Setup Method] [WPS: Button], [WPS: PIN Code], [Search for Access Points]
[SSID] Network name up to 32 characters
[Authn/Encr Method] [WPA, WPA2-PSK / TKIP, AES], [Open/No encryption], [Open/WEP 1] to [Open/WEP 4],
[Shared Key/WEP 1] to [Shared Key/WEP 4]
[Password]
[IP Address Assign.] [Automatic], [Manual]
[IP Address],
[Subnet Mask],
[Default Gateway]
0.0.0.0 to 255.255.255.255 ([0.0.0.0])
[Protocol] [UDP], [RTP], [RTP+FEC], [RTSP+RTC]
[Dest. IP Address] 0.0.0.0 to 255.255.255.255 ([0.0.0.0])
[Dest. Port No.] 1024 to 65530 ([5000])
[FEC Port No.] 1026 to 65532 ([5002])
[FEC Interval] 10 to 100 in intervals of 5 (100)
[RTSP: User Name] User name up to 24 characters ([user])
[RTSP: Password] Password up to 32 characters ([12345678])
Submenu levels / Menu items Setting options and additional information
201
Setup Screens and Menu Options
[Video Output Conf.] When [System Frequency] is set to [59.94 Hz]:
[9Mbps/1920x1080 59.94i], [4Mbps/1920x1080 59.94i], [2Mbps/1280x720 29.97P],
[1.5Mbps/720x480 59.94i]
When [System Frequency] is set to [50.00 Hz]:
[9Mbps/1920x1080 50.00i], [4Mbps/1920x1080 50.00i], [2Mbps/1280x720 25.00P],
[1.5Mbps/720x576 50.00i]
[Audio Out Channels] [CH1/CH2], [CH3/CH4]
[Check MAC Address]
Displays the MAC address when the camera is connected to a wired (Ethernet) network or when an
optional wireless transmitter is attached.
[FTP Transfer] These settings are available only when the menu is opened from the PLAY screen
(A 143).
(A 185)
[Activate]
[Connection Method] [Ethernet], [Infrastructure]
[Wi-Fi Setup Method] [WPS: Button], [WPS: PIN Code], [Search for Access Points]
[SSID] Network name up to 32 characters
[Authn/Encr Method] [WPA, WPA2-PSK / TKIP, AES], [Open/No encryption], [Open/WEP 1] to [Open/WEP 4],
[Shared Key/WEP 1] to [Shared Key/WEP 4]
[Password]
[IP Address Assign.] [Automatic], [Manual]
[IP Address],
[Subnet Mask],
[Default Gateway],
[Primary DNS Server],
[Secndry DNS Server]
0.0.0.0 to 255.255.255.255 ([0.0.0.0])
[FTP Server] Server name up to 32 characters
[FTP: User Name] User name up to 32 characters
[FTP: Password] Password up to 32 characters
[Destination Folder] Destination folder’s path up to 152 characters (Default is the root folder [/])
[Port No.] 1 to 65535 ([21])
[Passive Mode] [On], [Off]
[New Folder by Date] [On], [Off]
[Same Named Files] [Skip], [Overwrite]
[Check MAC Address]
Displays the MAC address when the camera is connected to a wired (Ethernet) network or when an
optional wireless transmitter is attached.
[GPS] These settings are available only when the optional GP-E1 GPS Receiver is attached to
the camera.
(A 120)
[Activate], [Auto Time Setting] [On], [Off]
[Display Info]
Displays a screen where you can check the data received from the GPS signal (latitude, longitude,
altitude, UTC data) as well as an indication of the satellite signal’s strength.
[Retract Lens] [On], [Off]
When one of the following lenses is attached to the camera and the focus mode switch on the lens is
set to AF, if this setting is set to [On], the lens will retract fully when the camera is turned off.
EF40mm f/2.8 STM EF-S24mm f/2.8 STM EF50mm f/1.8 STM
[Reset Hour Meter]
The camera has two “hour meters” – the first keeps track of total operation time and the second
keeps track of operation time since the last time the second hour meter was reset with this function.
Submenu levels / Menu items Setting options and additional information
Setup Screens and Menu Options
202
* Monitoring menu only.
** The default value depends on the country/region or purchase.
*** Camera menu only.
[My Menu]* / [My Menu 1]** ( )
* Camera menu only.
** Default setting in the monitoring menu only. The number in the menu setting and icon will reflect the My Menu set currently
selected.
[Certification Logos]***
Displays certification logos that apply to this camera on the control display.
[Firmware]
[Camera], [Remote OU-700]
Displays the current firmware version of the camera or updates the firmware version of an optional
OU-700 Remote Operation Unit. These settings are usually unavailable.
[Lens] (A 45)
[CDX-36150]
Updates the firmware version of a commercially available CDX-36150 Recorder docked with the
camera.
Submenu levels / Menu items Setting options and additional information
[Select] Camera menu: [1: CAMERA-1], [2: CAMERA-2], [3: CAMERA-3]
Monitoring menu: [1: CAMERA-4], [2: CAMERA-5], [3: CAMERA-6]
(A 35)
[Edit] [Register], [Move], [Delete], [Reset All], [Rename]
Submenu levels / Menu items Setting options and additional information
9
203
Using the CDX-36150 Recorder
Preparations
This section explains how to attach the commercially available CDX-36150 Recorder to the camera and remove
it, and insert recording media (Codex Capture Drive 2.0) to the recorder and initialize recording media. When
attaching the recorder, make sure to use the reinforcement plate supplied with the camera.
For safety and maintenance instructions and detailed information about the recorder, refer to the CDX-36150
Recorder’s Getting Started Guide.
Attaching the CDX-36150 Recorder to the Camera
1 Press the
Q
button to turn off the camera.
2 Remove the battery adapter that comes attached to the
camera (A 23).
3 Attach the recorder to the camera (A 24).
Follow steps 1 to 4 in the procedure to attach the recorder in
the same way explained for attaching a battery adapter.
Pull out the locking lever on the recorder to attach it to the
camera.
4 Attach the reinforcement plate (supplied with the camera)
to the recorder.
5 Using the hex wrenches supplied with the camera, fasten
the 6 fixation screws shown in the illustration (4 on top,
2 on the bottom) to secure the recorder in place.
Use the 1/4" (0.64 cm) wrench for the 2 top plate screws
closer to the front of the camera and the M4 wrench for the
rest of the screws and bolts (top/bottom plates).
Preparations
204
Removing the CDX-36150 Recorder
1 Press the
Q
button to turn off the camera.
2 Remove all power sources connected to the recorder
(DC IN and battery).
3 Use the hex wrenches supplied with the camera to
remove the 6 screws shown in the illustration.
Use the 1/4" (0.64 cm) wrench for the 2 top plate screws
closer to the front of the camera and the M4 wrench for the
rest of the screws and bolts (top/bottom plates).
4 Remove the reinforcement plate from the recorder.
5 Remove the recorder (A 23).
Follow the procedure to remove the recorder in the same
way explained for removing the battery adapter.
Pull out the locking lever on the recorder to remove it from
the camera.
NOTES
Be careful not to obstruct in any way the recorder’s air vents.
To use the camera’s DC IN 12V terminal when the recorder is attached
to the camera, remove the cover next to the CDX-36150 Recorder’s
DC IN terminal.
Powering the CDX-36150 Recorder
Connect the power supply to the CDX-36150 Recorder before turning on the camera. While the CDX-36150
Recorder is docked with the camera, power is supplied to the camera from the power source connected to the
CDX-36150 Recorder. You can also connect a power source directly to the camera’s DC IN 12V terminal.
1 Press the camera’s Q button to turn off the camera.
2 Connect the power supply (DC IN or battery) to the recorder.
Refer to the CDX-36150 Recorder’s Getting Started Guide.
3 Press the camera’s
Q
button to turn on the camera.
The LED on the top of the CDX-36150 Recorder will illuminate in different colors to indicate the recorder’s
status. Refer to the following table.
Air vents
Cover
205
Preparations
CDX-36150 Recorder’s LED status
You can press the button inside the ring to change the LED’s
brightness between 3 levels or to turn it off completely. Even when you
turn it off, the LED will illuminate in red if a low power warning is
triggered.
Initializing a Capture Drive
For details about the recording media and how to insert a Capture Drive 2.0 into the recorder, refer to the CDX-
36150 Recorder’s Getting Started Guide. The first time you use a Capture Drive with the camera, initialize it first
using the camera’s menu.
1 Set the main recording format to [RAW ( Capture Drive)] or [ProRes ( Capture Drive)] (A 65).
[Rec/Media Setup] (3) > [Main Rec Format] > [RAW ( Capture Drive)] or
[ProRes ( Capture Drive)]
2 Initialize the Capture Drive in the recorder.
[Rec/Media Setup] (3) > [Initialize Media] > [ Capture Drive]
3 Camera menu: Press both [FORMAT] buttons simultaneously.
Monitoring menu: Select [OK] and then press SET.
Refer also to
Initializing Recording Media
(A 51).
The Capture Drive will be initialized for use with the recording format selected in step 1.
IMPORTANT
Initializing a Capture Drive will permanently erase all the data it contains. Lost data cannot be recovered. Make
sure you save important recordings in advance.
Observe the following precautions while the camera is accessing the Capture Drive in the recorder. Failure to
do so may result in permanent data loss.
- Do not turn off the camera or recorder. Do not remove/disconnect the battery or other power source.
- Do not open the recorder’s Capture Drive bay.
NOTES
You can check the capacity and remaining available recording time of the Capture Drive on the
[MEDIA] screen.
A Capture Drive cannot be used to record clips in different recording formats (RAW and ProRes).
When you initialize a Capture Drive with the main recording format set to [ProRes ( Capture Drive)], the
recordable space will be reduced to approximately half of the Capture Drive's nominal capacity to ensure a
highly reliable format thanks to the use of multi-stream processing.
LED Recorder status
Blue Record standby mode.
Red
While recording, or the power level of the power source connected
to the CDX-36150 Recorder is low.
Green During playback.
Off
The camera is turned off or the main recording format is set to an
option other than [RAW ( Capture Drive)] or
[ProRes ( Capture Drive)].
LED
Recording with the CDX-36150 Recorder
206
Recording with the CDX-36150 Recorder
After the recorder is ready and the Capture Drive has been initialized for use with the camera, you can use it to
record the camera’s RAW data. You are able to shoot using normal recording or slow & fast motion recording.
This section will cover only those aspects that are different from what is explained in previous chapters of this
instruction manual.
Video Configuration
The following video configuration combinations are available when using the CDX-36150 Recorder to record the
camera’s RAW data. The audio recorded will be 4-channel linear PCM audio (24 bit, 48 kHz).
Available video configurations
Before using the CDX-36150 Recorder to make important recordings for the first time, make test recordings
using the video configuration(s) you plan to use to check that the camera and recorder are operating correctly.
Main recording format Sensor mode Resolution Codec Frame rate
[RAW ( Capture Drive)]
Full frame
qr 5952x3140
qr 5952x2532
59.94P
50.00P
29.97P
25.00P
24.00P
23.98P
Super 35mm
Z[ 4512x2376
] 4272x2376
Z[ 4512x1920
Super 35mm
Super 35mm (cropped)
4096x2160
Super 16mm (cropped) 2048x1080
[ProRes ( Capture Drive)]
Full frame
Super 35mm
Super 35mm (cropped)
4096x2160
3840x2160
ProRes 422 HQ, 10 bit
Full frame
Super 35mm
Super 35mm (cropped)
Super 16mm (cropped)
2048x1080
1920x1080
ProRes 4444 XQ, 12 bit
ProRes 4444, 12 bit
ProRes 422 HQ, 10 bit
207
Recording with the CDX-36150 Recorder
Shooting frame rates during slow & fast motion
Available shooting frame rates vary depending on the [Frame Rate] setting selected in the video configuration.
The range of available shooting frame rates depends also on the resolution and codec used, as shown at the top
of the following tables (Ü = the shooting frame rates listed under the column are available).
Z[]
Available shooting frame rates (RAW)
qr
Available shooting frame rates (RAW)
Sensor mode Resolution Available range
Super 35mm
Z[ 4512x2376
] 4272x2376
Ü
Z[ 4512x1920
4096x2160
Ü Ü
Super 16mm (cropped) 2048×1080 Ü Ü Ü
[Frame Rate] setting Shooting frame rate
59.94P 1, 2, 3, 6, 15, 30, 60, 90 120 150, 180, 210, 240
29.97P
1, 2, 3, 6, 15, 30, 32, 36, 40, 44,
48, 52, 56, 60, 90
120 150, 180, 210, 240
23.98P
24.00P
1, 2, 3, 6, 12, 24, 26, 28, 30, 32,
36, 40, 44, 48, 52, 56, 60, 72, 96
120 144, 168, 192, 216, 240
50.00P 1, 5, 15, 25, 50, 54, 58, 75, 100 125, 150, 175, 200
25.00P
1, 5, 15, 25, 26, 28, 30, 34, 38,
42, 46, 50, 54, 58, 75, 100
125, 150, 175, 200
Sensor mode Resolution Available range based on resolution
Full Frame
5952x3140
5952x2532
Ü
Super 35mm (cropped) 4096x2160 Ü Ü
Super 16mm (cropped) 2048x1080 Ü Ü
Ü
Frame rate Shooting frame rate
59.94P 1, 2, 3, 6, 15, 30, 60 90, 120, 150
29.97P
1, 2, 3, 6, 15, 30, 32, 36, 40, 44,
48, 52, 56, 60
90, 120, 150
23.98P
24.00P
1, 2, 3, 6, 12, 24, 26, 28, 30, 32,
36, 40, 44, 48, 52, 56, 60
72 96, 120, 144, 168
50.00P 1, 5, 15, 25, 50 54, 58, 75 100, 125, 150
25.00P
1, 5, 15, 25, 26, 28, 30, 34, 38,
42, 46, 50
54, 58, 75 100, 125, 150
Recording with the CDX-36150 Recorder
208
Z[]
Available shooting frame rates (ProRes)
1
Selected with the [Rec/Media Setup] > [Bit Rate] setting.
qr
Available shooting frame rates (ProRes)
1
Selected with the [Rec/Media Setup] > [Bit Rate] setting.
2
Only when [Camera Setup] > [Sensor Mode] is set to [Super 35mm (Cropped)].
Sensor mode Resolution Codec
1
Available range
Super 35mm
4096x2160
3840x2160
ProRes 422 HQ Ü
2048x1080
1920x1080
ProRes 4444 XQ
ProRes 4444
Ü
2048x1080
1920x1080
ProRes 422 HQ Ü Ü
Super 16mm (cropped)
2048x1080
1920x1080
ProRes 422 HQ Ü Ü Ü
[Frame Rate] setting Shooting frame rate
59.94P 1, 2, 3, 6, 15, 30, 60 90, 120 150, 180, 210, 240
29.97P
1, 2, 3, 6, 15, 30, 32, 36,
40, 44, 48, 52, 56, 60
90, 120 150, 180, 210, 240
23.98P
24.00P
1, 2, 3, 6, 12, 24, 26, 28,
30, 32, 36, 40, 44, 48, 52,
56, 60
72, 96, 120 144, 168, 192, 216, 240
50.00P 1, 5, 15, 25, 50 54, 58, 75, 100 125, 150, 175, 200
25.00P
1, 5, 15, 25, 26, 28, 30, 34,
38, 42, 46, 50
54, 58, 75, 100 125, 150, 175, 200
Sensor mode Resolution Codec
1
Resolution/Available range
Full frame
Super 35mm (cropped)
4096x2160
3840x2160
ProRes422 HQ Ü
2048x1080
1920x1080
ProRes4444 XQ
ProRes4444
Ü
2048x1080
1920x1080
ProRes422 HQ Ü Ü
2
Super 16mm (cropped)
2048x1080
1920x1080
ProRes422 HQ
ProRes422
Ü Ü Ü
Frame rate Shooting frame rate
59.94P 1, 2, 3, 6, 15, 30, 60 90, 120, 150
29.97P
1, 2, 3, 6, 15, 30, 32, 36,
40, 44, 48, 52, 56, 60
90, 120, 150
23.98P
1, 2, 3, 6, 12, 24, 26, 28,
30, 32, 36, 40, 44, 48, 52,
56, 60
72 96, 120, 144, 168
50.00P 1, 5, 15, 25, 50 54, 58, 75 100, 125, 150
25.00P
1, 5, 15, 25, 26, 28, 30, 34,
38, 42, 46, 50
54, 58, 75 100, 125, 150
209
Recording with the CDX-36150 Recorder
Main Recording Video Configuration and Video Output Configuration from
the SDI OUT Terminals
1
[Rec/Media Setup] > [Main Rec Format] setting.
2
The frame rate of the video output will be the same as that used for recording (except when slow & fast motion recording is
activated).
3
The color sampling will be determined by the option selected for the [Rec/Media Setup] > [Resolution/Sampling]
setting.
4
When only one or two SDI connections are required, the other SDI OUT terminals output the same signal as SDI OUT 1 (or SDI
OUT 1 and SDI OUT 2). This is indicated by the gray cells in the table.
5
Video will be output at a resolution of 4096x2160.
6
Only when the resolution is 1920x1080.
Main recording video configuration Output from each terminal
3, 4
Number of
terminals
required
Output
signal
[Main Rec Format]
1
Resolution/
Color sampling
Frame rate
2
SDI OUT 1 SDI OUT 2 SDI OUT 3 SDI OUT 4
[RAW
( Capture Drive)]
qr
5952x3140
qr
5952x2532
Output stopped
Z[ 4512x2376
5
] 4272x2376
5
Z[ 4512x1920
5
4096x2160
RAW
60P to 120P
(120P inclusive)
Frame-sequential
4
3G
RGBA1 RGBA2 RGBA3 RGBA4
30P to 60P
(60P inclusive)
Frame-sequential
2
RGBA1 RGBA2
30P or lower RGBA 1
2048x1080
RAW
120P to 240P
(240P inclusive)
Frame-sequential
4
3G
RGBA1/
RGBA5
RGBA2/
RGBA6
RGBA3/
RGBA7
RGBA4/
RGBA8
60P to 120P
(120P inclusive)
Frame-sequential
2
RGBA1/
RGBA3
RGBA2/
RGBA4
60P or lower
RGBA1/
RGBA2
1
[ProRes
( Capture Drive)]
4096x2160
3840x2160
YCbCr 4:2:2, 10 bit
30P to 60P
(60P inclusive)
Square division (Quad HD)
4 3G
Upper
left
Upper
right
Lower
left
Lower
right
30P or lower
Square division (Quad HD)
4 HD
Upper
left
Upper
right
Lower
left
Lower
right
2048x1080
1920x1080
RGB 4:4:4, 12 bit
30P to 60P
(60P inclusive)
RGB 2
Dual link
3G
30P or lower RGB 1 3G
2048x1080
1920x1080
YCbCr 4:2:2, 10 bit
120P to 240P
(240P inclusive)
Frame-sequential
4
3G
YCC1 YCC2 YCC3 YCC4
60P to 120P
(120P inclusive)
Frame-sequential
2
YCC1 YCC2
30P to 60P
(60P inclusive)
YCC 1
30P or lower,
59.94i
6
, 50.00i
6
YCC 1 HD
Recording with the CDX-36150 Recorder
210
Main Recording Video Configuration and Video Output Configuration from the MON.
Terminals and HDMI OUT Terminal
1
[Rec/Media Setup] > [Main Rec Format] setting.
2
The frame rate of the video output will be the same as that used for recording (except when slow & fast motion recording is
activated).
3
Onscreen displays and assistance functions like peaking and zebra pattern can be output to an external monitor.
4
[System Setup] > [Term. Output Setup] > [MON. Output] setting.
5
When [System Setup] > [Term. Output Setup] > [MON. Output] is set to [Off], the HDMI OUT output will change
depending on the capabilities of the monitor used. When [MON. Output] is set to a setting other than [Off], if the monitor
connected to the terminal does not support the video output configuration, video output from the HDMI OUT terminal will be
turned off.
6
The color sampling will be set automatically to YCbCr 4:2:2, 10 bit, YCbCr 4:4:4, 8 bit or RGB 4:4:4, 8 bit, depending on the
capabilities of the external monitor.
7
[System Setup] > [Term. Output Setup] > [HDMI Max Res.] setting.
8
qr When the frame rate is 59.94P, the signal output from the MON. terminals is 59.94P but the image refreshes at
an equivalent to 29.97P. When the frame rate is 50.00P, similarly, the image refreshes at an equivalent to 25.00P.
Main recording video configuration Video output configuration
[Main Rec Format]
1
Frame
rate
2
Resolution
MON. terminals
3
HDMI OUT terminal
3, 5, 6
[MON. Output]
4
[HDMI Max Res.]
7
[2048x1080/
1920x1080]
[1920x1080]
[4096x2160/
3840x2160]
[1920x1080]
[RAW ( Capture Drive)]
59.94P
50.00P
29.97P
25.00P
24.00P
23.98P
qr
5952x3140
8
qr
5952x2532
8
Z[
4512x2376
Z[
4512x1920
4096x2160
2048x1080
2048x1080
YCbCr 4:2:2, 10 bit
1920x1080
YCbCr 4:2:2, 10 bit
1920x1080,
720x480 (59.94P),
720x576 (50.00P)
]
4272x2376
1920x1080
YCbCr 4:2:2, 10 bit
[ProRes ( Capture Drive)]
4096x2160
2048x1080
YCbCr 4:2:2, 10 bit
4096x2160
1920x1080,
720x480
(59.94P),
720x576
(50.00P)
3840x2160
1920x1080
YCbCr 4:2:2, 10 bit
3840x2160
2048x1080
2048x1080
YCbCr 4:2:2, 10 bit
1920x1080,
720x480 (59.94P),
720x576 (50.00P)
1920x1080
1920x1080
YCbCr 4:2:2, 10 bit
211
Recording with the CDX-36150 Recorder
1 Set the main recording format to [RAW ( Capture Drive)] or [ProRes ( Capture Drive)] (A 65).
[Rec/Media Setup] (3) > [Main Rec Format] > [RAW ( Capture Drive)] or
[ProRes ( Capture Drive)]
2 If necessary, select the desired sensor mode and system frequency (A 65).
3 Select the desired frame rate (A 65). To use slow & fast motion recording, activate it and select also
the desired shooting frame rate (A 68).
NOTES
When the main recording format is set to [RAW ( Capture Drive)], a special gamma curve, optimized for
RAW video, will be used.
Sub Recording on a CFast or SD Card
While using the CDX-36150 Recorder to record RAW data as the main recording, you can simultaneously have
the camera record a sub recording in XF-AVC format on a CFast card (XF-AVC Intra) or SD card (XF-AVC Proxy).
For details, refer to
Simultaneous Sub Recordings
(A 71).
NOTES
When the main recording format is set to [RAW ( Capture Drive)] or [ProRes ( Capture Drive)] and the
CDX-36150 Recorder is not docked with the camera, clips will not be recorded on the CFast card or SD card
even if simultaneous sub recording was activated. For this reason, even when the time code running mode is
set to [Regen.], the last time code recorded on the CFast or SD card will not be read.
Z[] When the resolution of the main recording format is 4512x2376 or 4272x2376, you
can display an onscreen marker that indicates the portion of the image being recorded as the sub recording.
For details, refer to
Displaying Onscreen Markers
(A 98).
Playing Back Recordings from the Capture Drive
Press the camera’s PLAY button to set the camera in playback mode. If you were recording on the CDX-36150
Recorder, information about the last clip recorded on the Capture Drive will be displayed on the control display.
During the playback of RAW clips, the [Canon Log 2] gamma, [Cinema Gamut] color space and [Neutral] color
matrix will be used.
For details about playback controls, refer to
Playback
(A 141).
To switch to playback from the Capture Drive after playing back recordings from other recording media:
1 From the PLAY screen, select the Capture Drive as the recording media to play back (A 142).
[PB MEDIA] > [ Capture Drive (RAW)] or [ Capture Drive (ProRes)]
Recording with the CDX-36150 Recorder
212
Playback Video Configuration and Video Output Configuration by Terminal
1
During the playback of sub recording (XF-AVC Proxy) clips, if the output of onscreen displays is activated for the MON. terminals,
the onscreen displays will be output also from the SDI OUT terminals.
2
[System Setup] > [Term. Output Setup] > [MON. Output] setting.
3
When [System Setup] > [Term. Output Setup] > [MON. Output] is set to [Off], the HDMI OUT output will change
depending on the capabilities of the monitor used. When [MON. Output] is set to a setting other than [Off], if the monitor
connected to the terminal does not support the video output configuration, video output from the HDMI OUT terminal will be
turned off.
4
The color sampling will be set automatically to YCbCr 4:2:2, 10 bit, YCbCr 4:4:4, 8 bit or RGB 4:4:4, 8 bit, depending on the
capabilities of the external monitor.
5
[System Setup] > [Term. Output Setup] > [HDMI Max Res.] setting.
6
Only available when [System Setup] > [Term. Output Setup] > [SDI OUT Output] is set to [Off].
NOTES
During the playback of RAW clips, if the camera’s onscreen displays are being output from the MON.
terminals, the onscreen displays will be superimposed also on video output from the SDI OUT terminals.
During the playback of RAW clips, the following onscreen displays will not appear on the monitoring screen.
The following operations are available during playback from the Capture Drive in the CDX-36150 Recorder.
For details, refer to
Clip/Photo Operations
(A 145).
Video configuration of the clip Video output configuration
[Playback Media]/
Resolution
Frame
rate
SDI OUT terminals
1
MON. terminals HDMI OUT terminal
3, 4
[MON. Output]
2
[HDMI Max Res.]
5
[2048x1080/
1920x1080]
[1920x1080]
[4096x2160/
3840x2160]
[1920x1080]
[ Capture Drive (RAW)]
qr
5952x3140
qr
5952x2532
Z[ 4512x2376
Z[ 4512x1920
4096x2160
2048x1080
59.94P
50.00P
29.97P
25.00P
24.00P
23.98P
2048x1080
YCbCr 4:2:2, 10 bit
2048x1080
YCbCr 4:2:2, 10 bit
1920x1080
YCbCr 4:2:2, 10 bit
1920x1080,
720x480 (59.94P),
720x576 (50.00P)
] 4272x2376
1920x1080
YCbCr 4:2:2, 10 bit
[ Capture Drive (ProRes)]
4096x2160
4096x2160
YCbCr 4:2:2, 10 bit
2048x1080
YCbCr 4:2:2, 10 bit
4096x2160
6
3840x2160
3840x2160
YCbCr 4:2:2, 10 bit
1920x1080
YCbCr 4:2:2, 10 bit
3840x2160
6
2048x1080
2048x1080 /
RGB 4:4:4, 12 bit
YCbCr 4:2:2, 10 bit
2048x1080
YCbCr 4:2:2, 10 bit
1920x1080,
720x480 (59.94P),
720x576 (50.00P)
1920x1080
1920x1080 /
RGB 4:4:4, 12 bit
YCbCr 4:2:2, 10 bit
1920x1080
YCbCr 4:2:2, 10 bit
- Shutter speed
-Aperture value
-ISO speed/gain
- Recording date/time
- Shooting frame rate
- Custom picture
- Relay recording icon
- $ mark/% mark
213
Recording with the CDX-36150 Recorder
Clip operations menu
* [PB MEDIA] setting.
Menu item
[Playback Media]*
[ Capture Drive (RAW)] [ Capture Drive (ProRes)]
[Display Clip Info] Ü Ü
[Add $ Mark], [Delete $ Mark] - -
[Add % Mark], [Delete % Mark] - -
[Delete] Ü Ü
[Delete User Memo] - -
[Copy / File] - -
[Recover Clip] - Ü
[FTP Transfer] - -
Recording with the CDX-36150 Recorder
214
10
215
Additional Information
Displaying the INFO Screens
You can use the INFO screens to check the camera’s status and various settings.
1 Press the INFO button to open the INFO screen.
The [LIVE] screen (camera status) will appear on the control display.
2 Press other screen buttons as necessary to check the other information screens.
On INFO screens with many items turn the SELECT dial to scroll through all the information.
Options
[LIVE] screen: Camera status and error messages (
A
215).
[COLOR] screen: Color settings (gamma curve, color space, color matrix) in use (
A
216).
[CP] screen: Custom picture file (
A
216).
[SYSTEM] screen: Basic information about the system (
A
217)
[VIDEO] screen: Information about the video output signals (
A
217)
[MEDIA] screen: Information about recording media (
A
218).
[LIVE] (current status) screen
When the INFO icon appears on the control display,
open the [LIVE] screen to check important
information regarding the status of the camera. If there
are no problems with the camera, [System Status: Good]
will be displayed. If an error message appears on this
screen, check the list of messages (
A
224).
Displaying the INFO Screens
216
[COLOR] screen
[CP] screen
Gamma curve, color space and color matrix used
for recordings, video output and displays.
1 [CFast]: Settings used for clips recorded on the
CFast card (A 84, 134)
[SD Card]: Settings/LUT used for sub recording
(XF-AVC Proxy) clips (A 71)
2 Settings/LUT used for video outputs from the
respective terminals
1
(A 155)
3 [VIDEO]: Settings/LUT used for the optional
viewfinder
1
(A 155)
1
When a user LUT is applied, the user LUT’s name
will appear for the gamma curve.
Custom picture settings in use.
1 Custom picture file name (A 131)
2 Preset color settings (A 84)
3 Custom picture main settings (A 134)
4 Custom picture other settings (A 135)
3
1
2
1
2
3
4
217
Displaying the INFO Screens
[SYSTEM] screen
[VIDEO] screen
1 Date and time (A 29)
2 CDX-36150 Recorder’s power supply (voltage)
3Sensor mode (A 65)
4 System frequency (A 65)
5 Main recording format (A 65)
6 Resolution (A 66)
7 Total operation time
8 Operation time since [Reset Hour Meter] was
used last (A 201)
9 Temperature warning and fan operation (A 64)
1 Output signal from the HDMI OUT terminal
(A 154)
2 Output from the MON. terminals activated or not
(A 153)
3 Output from the SDI OUT terminals activated or
not (A 152)
4
3
1
5
6
7
8
9
2
1
2
3
Displaying the INFO Screens
218
[MEDIA] screen
NOTES
Depending on the recording media, the total space displayed on the screen may differ from the nominal
capacity listed on the CFast card or SD card.
1 CFast card A and recording format
2 CFast card B and recording format
3 Capture Drive 2.0 in a CDX-36150 Recorder
docked with the camera
4SD card
5User memo (A 118, 180)
User memo file name, title, creator, shooting
location and description
For each:
6 Visual bar: Approximate used/available space
7Total space
8 [Recorded]: Used space
9 [Available]: Available recording time
Only for the SD card:
10 SD speed class
11 Number of remaining photos
1
2
3
4
5
6
10 11
7 8 9
219
Troubleshooting
Troubleshooting
If you have a problem with your camera, refer to this section. Consult your dealer or a Canon Service Center if
the problem persists.
Power source
The camera will not turn on or it turns off by itself.
- The input voltage of the battery or power source connected to the DC IN 12V terminal is too low. Check the power
source.
- Excess current to the lens has been detected. Remove the lens. Clean the contacts on the lens mount and lens and
reattach the lens.
Recording
The camera’s controls are not responsive/disabled.
- When the key lock function is activated, all buttons (or all buttons with the exception of some REC buttons) are locked
and cannot be operated. Press and hold the
C
button for about 4 seconds to turn off the key lock function. You can
change which controls are locked with the [System Setup] > [Key Lock] setting.
The ND FILTER buttons do not respond.
- The ND FILTER buttons have been disabled. Set [System Setup] > [ND FILTER Button] to [Enable].
Pressing the REC button will not start recording.
- The CFast card is full or it already contains the maximum number of clips (999 clips). Delete some clips (A 147) or
save your clips (A 161) and initialize the CFast card (A 51) to free some space. Alternatively, replace the CFast card.
- The REC button that was used may be disabled. Change the current settings in the [System Setup] > [REC
Button] submenu to enable the use of the desired REC buttons.
- The camera cannot start recording when input power supplied to the camera reaches the level set for the power level
warning (A 199). Check the power source.
- You may not be able to start or stop recording while controls on the optional RC-V100 Remote Controller are being
operated. Stop using the remote controller and then press the REC button.
The point where the REC button was pressed does not match the beginning/end of the recording.
- There is a slight interval between pressing the REC button and the actual start/end of recording. This is not a
malfunction.
The camera will not focus.
- The camera may not be able to focus on certain subjects using autofocus. Focus manually (A 90).
- When the AF mode is set to AF-boosted MF, start focusing manually until the AF frame changes to white (automatic
adjustment range).
- The optional viewfinder is not adjusted. Use the dioptric adjustment ring to make the proper adjustment (A 42).
- The lens is dirty. Clean the lens with a soft lens-cleaning cloth.
Z[qr When a subject flits across in front of the lens, the image appears slightly bent.
- This is a phenomenon typical of CMOS image sensors. When a subject crosses very quickly in front of the camera, the
image may seem slightly warped. This is not a malfunction.
Bright red, green or blue dots appear on the monitoring screen.
- Try adjusting the black balance (A 54). The camera’s CMOS sensor is a delicate piece of precision engineering. Direct
exposure of the sensor to ion rays or other types of cosmic radiation may affect it and this may rarely appear as bright colored
dots on the screen. This is the nature of CMOS image sensors and does not represent a malfunction.
- The effects of the damage may be more noticeable when the camera is used in places subject to high temperatures,
when a high ISO speed or gain level is used and when slow shutter speeds are used.
The camera cannot record properly.
- This may occur as recordings are made and deleted over time. Save your clips (A 161) and initialize the recording media
(A 51), using the [Complete] option for SD cards.
After using the camera for a long time, it becomes hot.
- The camera may become hot after using it continuously for long periods of time; this is not a malfunction. If the
camera becomes unusually hot or it becomes hot after using it only for a short while, it may indicate a problem with
the camera. Consult a Canon Service Center.
Troubleshooting
220
Playback
Cannot delete a clip.
- You cannot delete XF-AVC clips with an
$
mark. Remove the
$
mark (A 147) to delete the clip.
- The LOCK switch on the SD card is set to prevent accidental erasure. Change the position of the LOCK switch.
Deleting clips takes longer than usual.
- When the recording media contains a large number of clips, some operations may take longer than usual. Save your
clips (A 161) and initialize the recording media (A 51).
Cannot delete a photo.
- The LOCK switch on the SD card is set to prevent accidental erasure. Change the position of the LOCK switch.
- Photos that were protected using other devices cannot be deleted with the camera.
Indicators and Onscreen Displays
appears in yellow on the control display.
- An error or other situation that requires your attention has been detected by the camera. Press the INFO button and
check the information in the [LIVE] screen (A 215).
The tally lamp does not illuminate.
- Set [System Setup] > [LED] > [Tally Lamp] > [Camera] to [On].
The tally lamp flashes quickly in red. (4 flashes per second)
- The input voltage of the battery or power source connected to the DC IN 12V terminal is too low. Replace the power
source.
- There is not enough available space on the CFast card. Delete some clips (A 147) to free some space or replace the
CFast card.
- A system error has occurred. Turn the camera off and then on again. If this does not solve the problem, consult a
Canon Service Center.
The tally lamp flashes slowly in red. (1 flash per second)
- The combined available space on both CFast cards is low. Replace the CFast card that is not being recorded onto.
9
appears in red on the control display and monitoring screen.
- An SD card error occurred. Remove and reinsert the SD card. If the display does not change back to normal, save your
recordings (A 161) and initialize the SD card (A 51).
- The SD card is full. Replace the SD card or delete some recordings (A 147) to free some space on the SD card.
Even after stopping recording, the access indicator stays illuminated in red.
- The clip is being recorded on the card. This is not a malfunction.
b
appears in yellow on the control display and monitoring screen.
- The camera’s internal temperature has reached a predetermined level. You can continue using the camera.
b
appears in red on the control display and monitoring screen.
- The camera’s internal temperature has risen further while
b
appeared in yellow on the screen.
- If the fan mode (A 64) is set to [Always On], turn off the camera and wait until the temperature has decreased.
- If the fan mode is set to [Automatic] and the fan was turned off while recording, the fan will turn on automatically (in
that case,
`
will appear on the control display and monitoring screen).
i
appears on the monitoring screen.
- The camera and lens cannot communicate normally. Clean the lens’s contacts and reattach the lens.
appears in red on the control display and monitoring screen
- The lithium button battery’s charge is low. If you have not used the camera for more than a month the built-in backup
battery may be completely depleted. To ensure the camera’s settings are not lost, save the camera’s settings on an SD
card (A 140) and replace the lithium button battery (A 24). After checking that the warning icon does not appear any
more, restore the camera’s settings from the file saved on the SD card.
appears in red on the monitoring screen.
- When [F. ASSIST.] > [OPTIONS] > [Magnification] > [Available While Rec] is set to [Off], the magnification
function is not available while recording. Set [Available While Rec] to [On].
The aperture value (F or T) appears in gray on the control display and monitoring screen.
- When using a compatible EF Cinema lens (A 240) or broadcast lens, the aperture value will appear in gray when the
camera detects that the aperture may be close to fully closed. As you continue to close down the aperture further, the
display will change to [closed].
qr
The ND filter indicator appears in red or as [- -] on the monitoring screen.
- The ND filter mechanism may not be working properly. Consult a Canon Service Center.
221
Troubleshooting
qr
The optional RC-V100 Remote Controller’s ND filter indicator flashes.
- The ND filter mechanism may not be working properly. Consult a Canon Service Center.
Picture and Sound
The optional viewfinder does not turn on.
- Make sure the unit cable connecting the camera’s VIDEO terminal and the optional viewfinder’s VIDEO terminal is
correctly connected on both sides.
There is no image on an external monitor.
- The camera is not connected correctly to the external monitor. Make sure you are using the correct connection
(A 152).
- The video input on the external monitor is not set to the video terminal to which you connected the camera. Select the
correct video input.
There is no picture or sound from an external monitor connected to an SDI OUT terminal.
- Set [System Setup] > [Term. Output Setup] > [SDI OUT Output] to [On].
- Check that the external monitor’s settings match the configuration of the output signal selected on the camera
(A 149).
There is no picture or sound from an external monitor connected to a MON. terminal.
- Set [System Setup] > [Term. Output Setup] > [MON. Output] to an option other than [Off].
- Check that the external monitor’s settings match the configuration of the output signal selected on the camera
(A 149).
There is no picture or sound from an external monitor connected to the HDMI OUT terminal.
- Disconnect the HDMI cable and then restore the connection or turn the camera off and then on again.
- When output from the MON. terminals is enabled ( [System Setup] > [Term. Output Setup] > [MON. Output]
is set to an option other than [Off]), if the monitor is not compatible with the video output configuration, output from the
HDMI OUT terminal will be turned off. Set [MON. Output] to [Off] or connect a monitor compatible with the HDMI OUT
terminal’s video output configuration.
The peaking/magnification/zebra pattern/waveform monitor/onscreen markers/false color display/B&W image does
not appear on the monitoring screen, or the anamorphic desqueeze/LUT is not applied to it.
- Check that display of the desired assistance function is enabled on the screen used with the corresponding output
settings.
- If output of the camera’s onscreen displays is not enabled for the terminal used, enable it (A 154).
HDR video output to external monitors appears brighter now than before updating the firmware.
- With the current firmware version, the camera follows the ITU-R BT.2408 report’s recommendations regarding
reference brightness levels for HDR output. The recordings themselves have not been changed.
Screen displays turn on and off repeatedly.
- The input voltage of the battery or power source connected to the DC IN 12V terminal is too low. Check the power
source.
- Excess current to the lens has been detected. Remove the lens. Clean the contacts on the lens mount and lens and
reattach the lens.
Abnormal characters appear on the monitoring screen and the camera does not operate properly.
- Disconnect the power source and reconnect it after a short time. If the problem still persists, use the [System
Setup] > [Reset] > [All Settings] function. This resets all the camera’s settings to default values, except for the hour
meter.
Noise artifacts (vertical stripes) appear on the screen.
- This may occur when the camera is used in high temperature conditions. Adjusting the black balance (A 54) may
help in such cases.
Video noise appears on the monitoring screen.
- Keep a distance between the camera and devices that emit strong electromagnetic fields such as near powerful
magnets and motors, MRI machines or high-voltage power lines.
Z[qr
Horizontal bands appear on the monitoring screen.
- This is a phenomenon typical of CMOS image sensors when recording under some types of fluorescent, mercury or
sodium lamps. This is not a malfunction. You may be able to reduce the symptoms by setting the shutter speed mode
to [Speed] and the shutter speed to a value matching the frequency of the local electrical system: 1/50* or 1/100 for
50 Hz systems, 1/60 or 1/120 for 60 Hz systems.
* May not be available depending on the frame rate.
Troubleshooting
222
Audio cannot be recorded.
- The audio input selection switch of the INPUT terminal is in the AES/EBU position but an analog audio source is
connected, or it is set to the ANALOG position and a digital audio source is connected. Set the audio related switches
correctly according to the audio source you wish to use (A 110).
- The external analog microphone connected to the INPUT 1/INPUT 2 terminal requires phantom power. Set the
corresponding INPUT terminal’s ANALOG (analog audio source selection) switch to MIC+48V (A 110).
Audio is recorded at an extremely low level.
- The audio recording level mode for the audio channels selected is set to manual (M or [Manual]) and the audio
recording level is set too low. Check the audio level meter on the HOME screen, [AUDIO] screen or on the
monitoring screen and adjust the audio level correctly (A 111).
- The microphone attenuator is on. Turn off the microphone attenuator (A 113, 113).
Sound is distorted or is recorded at lower levels.
- When recording near loud sounds (such as fireworks, shows or concerts), sound may become distorted or it may not
be recorded at the actual levels. Activate the microphone attenuator (A 113, 113), or adjust the audio recording level
manually.
Recording Media and Accessories
Cannot insert the recording media.
- The CFast card or SD card you are trying to insert is not facing the correct direction. Turn it over and insert it.
Cannot record on the CFast card.
- A compatible CFast card must be used (A 48).
- Initialize the CFast card (A 51) when you use it with the camera for the first time.
- The CFast card is full or it already contains the maximum number of clips (999 clips). Delete some clips (A 147) to
free some space or replace the CFast card.
Cannot record on the SD card.
- A compatible SD card must be used (A 48).
- Initialize the SD card (A 51) when you use it with the camera for the first time.
- The LOCK switch on the SD card is set to prevent accidental erasure. Change the position of the LOCK switch.
- The SD card is full. Delete some recordings (A 147) to free some space or replace the SD card.
- The folder and photo numbers have reached their maximum value. Set the [Rec/Media Setup] > [Photo
Numbering] setting to [Reset] and insert a new SD card.
Recording to and playing back from a CFast card is slow.
- This may occur as video is recorded/deleted over time. Save your clips (A 161) and initialize the CFast card (A 51).
Recording to and playing back from an SD card is slow.
- This may occur as clips and photos are recorded/deleted over time. Save your recordings (A 161) and initialize the
SD card using the [Complete] option (A 51).
The optional RC-V100 Remote Controller or commercially available remote control does not work.
- Make sure that [System Setup] > [REMOTE Term.] is set to [RC-V100 (REMOTE A)] or [RC-V100 (REMOTE
B)] (depending on the connection used) when using the optional RC-V100 Remote Controller or to [Standard] when
using a commercially available remote control.
- Turn off the camera, reconnect the remote controller and then turn the camera back on again.
- When editing of the custom picture files detailed settings ([Other Settings] > [Activate]) is not enabled or the currently
selected custom picture file is protected, detailed custom picture settings cannot be adjusted using the RC-V100.
Select a custom picture file that is not protected (A 131) and enable the editing of the custom picture file’s detailed
settings (A 131).
223
Troubleshooting
Network Functions
Check This First
Cannot connect with an access point.
- If the network function icon does not turn white, turn off the camera, remove the wireless file transmitter and attach it
again (A 164).
- Check that the settings on the network device the camera is trying to connect with are correct.
- Password information is not saved with the camera settings saved on an SD card. When you load onto the camera
settings from an SD card, all the passwords in the network-related settings are reset. Set up the network-related
settings as necessary (A 169).
- The wireless signal is not strong enough or there are other devices in the vicinity interfering with the wireless signal.
Refer to Precautions Regarding Wi-Fi Networks (A 224).
Cannot establish a Camera Access Point connection with a network device.
- If the network function icon does not turn white, turn off the camera, remove the wireless file transmitter and attach it
again (A 164).
- When you reset all the camera settings, all network settings are lost as well. Set up the Camera Access Point settings
again (A 165).
- The wireless signal is not strong enough or there are other devices in the vicinity interfering with the wireless signal.
Refer to Precautions Regarding Wi-Fi Networks (A 224).
Cannot connect with a wired (Ethernet) network.
- Use a category 5e or better shielded twisted pair (STP) Ethernet cable.
- Try replacing the Ethernet cable.
- When you reset all the camera settings, all network settings are lost as well. Connect using the default settings or set
up the network settings again (A 169).
- Check that the network device to which the camera is connected is on and functioning properly. To use 1000BASE-T
connection speeds, make sure to use network devices compatible with Gigabit Ethernet (1000BASE-T).
The (Ethernet) access indicator illuminates in red and then turns off.
- The Ethernet cable was disconnected or the camera cannot communicate with the connected network device. Check
the Ethernet connection and the connected network device.
The Browser Remote application will not start on the Web browser.
-Make sure [NETWORK] > [Browser Remote] > [ACTIVATE] is set to [On].
- The URL entered into the Web browser’s address bar is incorrect. Be sure to use the URL exactly as it appears in the
[Browser Remote] screen on the control display (A 171).
The Browser Remote screen is not displayed correctly on the Web browser.
- The device, operating system or Web browser used may not be supported. For the latest information about supported
systems, visit your local Canon Web site.
- Enable JavaScript and cookies in your Web browser’s settings. For details, refer to the help modules or online
documentation of the Web browser used.
Cannot activate the IP streaming function.
- The main recording format is not set to [XF-AVC (CFast)]. Set it to [XF-AVC (CFast)] (A 65).
- The system frequency is set to 24.00 Hz. Set it to 59.94 Hz or 50.00 Hz (A 65).
- Slow & fast motion recording is activated. Turn it off (
A 68
).
-
If the IP streaming’s [Protocol] is set to an option other than [RTSP+RTP], be sure to configure the receiver’s IP address
with the [Dest. IP Address] setting.
Are the access point (wireless router), camera, computer or other network devices all turned on?
Is the network working and correctly configured?
Are all network devices correctly connected to the same network as the camera?
When using Wi-Fi networks:
- Is the wireless file transmitter correctly attached to the camera’s system extension terminal (A 164)?
- Are there any obstructions between the camera and the access point or between the network device
used and the access point?
Troubleshooting
224
Precautions Regarding Wi-Fi Networks
When using a Wi-Fi network, try the following corrective actions if the transmission rate drops, the connection is
lost, or other problems occur.
Positioning a network device (access point, mobile device, etc.)
- When using a Wi-Fi network indoors, place the network device in the same room as the camera.
- Place the network device in an open, unobstructed location, where people or objects do not come between it and the
camera.
- Place the network device as close as possible to the camera. Change the height or facing of the network device, as
necessary.
Nearby electronic devices
- If the transmission rate over a Wi-Fi network drops because of interference from the following electronic devices,
switching to the 5 GHz band or to a different channel may solve the problem.
- Wi-Fi networks using the IEEE 802.11b/g/n protocol operate in the 2.4 GHz band. For this reason, the transmission
rate may drop if there are nearby microwave ovens, cordless telephones, microphones, or similar devices operating on
the same frequency band.
- If another access point operating on the same frequency band as the transmitter of the WFT-E6 or WFT-E8 connected
to the camera is used nearby, the transmission rate may drop.
Using multiple cameras/wireless transmitters/access points
- Check that there are no IP address conflicts among the devices connected to the same network.
- If multiple C700 / C700 PL/ C700 GS PL / C700 FF / C700 FF PL cameras are connected to a single access point,
connection speeds may be reduced.
- To reduce radio wave interference when there are multiple access points using IEEE 802.11b/g or IEEE 802.11n (in the
2.4 GHz band), leave a gap of four channels between each wireless access point. For example, use channels 1, 6, and
11, channels 2, 7, and 12, or channels 3, 8, and 13. If you can use IEEE 802.11a/n (in the 5 GHz band), switch to IEEE
802.11a/n and specify a different channel.
List of Messages
Refer to this section if a message appears in the [LIVE] screen on the control display or on the
monitoring screen. The messages in this section appear in alphabetical order. Note that for some messages, an
indication of the recording media involved (CFast A, CFast B,
8
, Capture Drive, or a combination thereof) may
appear above the message itself.
For error messages related to network functions, refer to
Network Functions
(A 227).
Accessing CFast A/CFast B/
8
/Capture Drive: Do not remove
- You opened the CFast card slot cover or SD card slot cover while the camera was accessing the recording media.
Close the card slot cover.
Buffer overflow. Recording was stopped.
- The data transfer rate was too high for the recording media in use and the recording was stopped. Use a
recommended recording media (A 48).
- Save your recordings (A 161) and initialize the recording media (A 51).
Camera
b
Lens communication error. Clean the lens’s contacts and reattach the lens.
- The camera cannot correctly communicate with the lens due to dirty lens contacts. After the message disappears, the
i
icon appears on the control display and monitoring screen. Clean the lens contacts with a soft cloth and
reattach the lens.
Cannot play back
- The file control information of an XF-AVC clip is corrupted or there was a decoder error. Turn the camera off and then
on again. If this does not solve the problem, consult a Canon Service Center.
Corrupted file control information cannot be recovered. Recording media or XF-AVC clips with corrupt file control
information cannot be read by Canon XF Utility.
Cannot switch CFast card slots
- The SLOT SEL. button was pressed while the camera is recording. Wait until recording is finished to change the
selected CFast card slot.
Capture Drive bay open.
- The recorder’s Capture Drive bay is open. Insert a Capture Drive and close the Capture Drive bay.
Capture Drive: Low battery level. Recording stopped.
- The charge of the CDX-36150 Recorder’s battery has gotten low, causing the recording to stop.
225
Troubleshooting
CFast A/CFast B/SD Card/Capture Drive: Check the data.
- Cannot access the recording media. Check the recording media and make sure it is inserted correctly.
- A recording media error occurred. The camera cannot record or display the image. Try removing and reinserting the
recording media, or use a different recording media.
- You inserted a MultiMedia Card (MMC) into the camera. Use a recommended SD card (A 48).
- If after the message disappears,
, ,
9
or appears in red, perform the following: Turn off the camera and
remove and reinsert the recording media. If , ,
8
or turns back to green you can resume recording/
playback. If the problem persists, save your recordings (A 161) and initialize the recording media (A 51).
CFast ACFast B / CFast BCFast A Switched
- This message appears when you use the SLOT SEL. button to switch the CFast card slot in use or recording
continued from one CFast card to the other.
CFast ACFast B / CFast BCFast A Will switch in a moment
- The CFast card is almost full so recording will continue on the other CFast card in approximately 1 minute.
Check the device connected to the camera’s system extension terminal
- There is a problem with the optional accessory connected to the camera’s system extension terminal. Try removing the
accessory and attaching it again. If this does not solve the problem, consult a Canon Service Center.
Conditions exceed the range of color/brightness that can be set.
- The reference white could not be calibrated using a custom white balance. Place a gray card or white object with no
pattern so it fills the center of the monitoring screen and try registering the custom white balance again.
Cover is open
- The CFast card slot cover or SD card slot cover was open when the camera was turned on or switched back from
playback mode to shooting mode. Insert a card and close the card slot the cover.
Fan error
- The cooling fan may not be working properly. Consult a Canon Service Center.
File name error
- The clip number has reached its maximum value. Save your clips (A 161) and initialize the recording media (A 51) or
delete all the clips (A 147).
- Photo numbers have reached their maximum value. Set [Rec/Media Setup]
> [Photo Numbering] to [Reset]
and delete all the photos on the SD card (A 147) or initialize it (A 51).
Firmware version mismatch error. Change the Remote OU-700’s firmware using the camera.
- The firmware of the optional OU-700 Remote Operation Unit connected to the camera does not match the camera’s
firmware. Update the OU-700’s firmware from the camera, using the [System Setup] > [Firmware] >
[Remote OU-700] setting.
Invalid operation
- The following operations cannot be performed.
Adding an
$
mark to a clip that already has an
$
mark or adding a
%
mark to a clip that already has a
%
mark.
Pressing the REC button when there are no recording media in the camera.
Lens Firmware update error. Try to update the firmware again.
- The lens’s firmware could not be correctly updated. Try updating the lens’s firmware again.
Lens error Change the frame rate
- The lens attached to the camera is not compatible for shooting at the frame rate selected on the camera. Select a
different the frame rate (A 65).
Lens error Turn the camera off, then on again.
- There was a communication error between the camera and the lens. Turn the camera off and then on again.
Low Power Warning Check the power supply.
- The input power supplied to the camera has reached the level set for the power level warning (A 199). Check the
power source.
- The message appears every time you press the REC button when the power supply is too low (as described above).
Management file error
- Cannot record because the camera cannot write to the file control information. This may occur if the files on the
recording media were accessed using another device. Save your clips (A 161) and initialize the recording media
(A 51).
May not be possible to record clips on this media
- You may not be able to record clips on an SD card without a Speed Class rating or rated CLASS 2 or 4. Replace the
SD card with one rated CLASS 6 or 10.
Troubleshooting
226
Media full
- The recording media is full. Delete some clips (A 147) to free some space or replace the recording media.
- CFast card A or CFast card B is full so recording will not start. Switch to the CFast card in the other CFast card slot to
record.
Media is almost full
- The amount of available space on CFast card A and CFast card B combined is low. Replace the CFast card that is not
selected.
- The amount of available space on the SD card is low. Replace the SD card or delete some recordings (A 147) to free
some space on the SD card.
Media is not supported
- 512 MB or smaller CFast cards and 128 MB or smaller SD cards cannot be used with the camera. Use a
recommended recording media (A 48).
- The Capture Drive inserted in the CDX-36150 Recorder is not compatible for use with the camera. Check the Capture
Drive.
Memory card is write-protected
- The LOCK switch on the SD card is set to prevent accidental erasure. Change the position of the LOCK switch.
No clips
- There are no clips on the recording media to play back. Clips must be recorded (A 55) in order to play them back.
No photos
- There are no photos on the SD card to play back. Photos must be taken (A 125) in order to view them.
Noise levels will rise on the image of the sub recording and on video outputs not in RAW.
- The main recording format is set to one of the RAW options and [Gamma] in the custom picture file is set to an option
other than [Canon Log 2] or [Canon Log 3]. Under such conditions, there may be more noise on video recorded with
sub recording clips on the CFast card and on video output from the SDI OUT terminals (except for RAW output), MON.
terminals and HDMI OUT terminal. If you do not need to output/record RAW data, change the main recording format to
one of the other options.
Number of clips already at maximum
- The recording media selected for recording already contains the maximum number of clips (999 clips). Replace the
recording media or use the CFast card in the other CFast card slot.
- Because both CFast cards reached the maximum number of clips, double slot recording is not available.
Number of ND filters used has changed. Check the focus.
- When using ND filter settings in the extended range (8 stops or 10 stops), the number of ND filters used changes and
this may result in a shift in focus. Check the focus before resuming shooting.
Recommend checking the data and initializing
- The recording media cannot be used for any of the following reasons.
A problem has occurred with the recording media.
The camera cannot read the data on the recording media.
The recording media was initialized using a computer.
The recording media is partitioned.
The Capture Drive is formatted for use with a different main recording format.
- Save your clips (A 161) and initialize the recording media (A 51).
Recorded at 24.00 Hz/50.00 Hz/59.94 Hz CFast A/CFast B/
8
/Capture Drive: Recommend checking the data and
initializing
- The recording media contains clips that were recorded using a system frequency different from the one currently used
by the camera. To record on this card, save your clips (A 161) and initialize the recording media with the camera
(A 51). To play back the recordings on the card, change the
[Rec/Media Setup] > [System
Frequency] setting to match the recordings on the recording media.
Recorded in ProRes/RAW format CFast A/CFast B/
8
/Capture Drive: Recommend checking the data and initializing
- The recording media contains clips that were recorded using a recording format different from the one currently used
by the camera. To record on this card, save your clips (A 161) and initialize the recording media with the camera
(A 51). To play back the recordings on the card, change the [Rec/Media Setup] > [Main Rec Format] setting to
match the recordings on the recording media.
Recording was stopped.
- The file control information is corrupted or there was an encoder error. Turn the camera off and then on again. Then,
remove the CFast card being used and reinsert it. Alternatively, replace the CFast card. If this does not solve the
problem, consult a Canon Service Center.
Corrupted file control information cannot be recovered. Recording media or XF-AVC clips with corrupt file control
information cannot be read by Canon XF Utility.
227
Troubleshooting
Network Functions
Along with this list, refer also to the instruction manuals of the access point or other external devices you are
using. For simplicity’s sake, in this section the optional WFT-E6 or WFT-E8 Wireless File Transmitter will be
referred to simply as “the transmitter”.
Remote OU-700 Firmware update error. Press the HOME button on the Remote OU-700 and wait a few moments.
- There was a problem while trying to update the optional OU-700 Remote Operation unit connected to the camera.
Press the HOME button on the OU-700 and wait. While the OU-700’s firmware is being updated do not remove the
power supply or turn off the camera, do not disconnect the OU-700 and do not operate any buttons or controls on the
camera or OU-700.
Replace the lithium button battery.
- The lithium button battery’s charge is low. Save the camera’s settings on an SD card (A 140) and replace the lithium
button battery (A 24). Then, restore the camera’s settings from the file saved on the SD card.
Some clips require data recovery
- The power may have been suddenly turned off or the recording media may have been removed while the camera was
recording. As a result, one or more clips contain corrupted data. You can try to recover the clips (A 53).
System error
- A system error has occurred. The camera cannot record clips. Consult a Canon Service Center.
The video configuration was changed. Check the settings.
- Some of the video configuration settings (frame rate, resolution, color sampling, bit rate or shooting frame rate).
This function is not compatible with the current lens.
- The selected setting is not compatible with the lens currently attached to the camera and cannot be used.
This photo cannot be displayed
- You may not be able to display photos taken with other devices or image files created or edited on a computer.
Unable to recover data
- Could not recover the selected clip. Save your clips (A 161) and delete the clips that could not be recovered
(A 147).
- The camera may not be able to recover clips when there is not enough space on the recording media. Delete some
clips (A 147) to free some space.
A User is already accessing the server. Try again later.
- This message appears on the screen of the connected device. Another device connected to the network is already
operating the camera. To use this device, first end the connection on the device accessing the camera and then touch
Retry.
Cannot log in to FTP server.
- Check the user name and password information in the FTP server settings (A 185).
Cannot transfer files to FTP server.
- Check that there is enough available space in the data storage device (hard disk, etc.) that contains the destination
folder on the FTP server.
- Check the user permissions/restrictions for accessing the FTP server.
Check the device connected to the camera’s system extension terminal
- There’s a hardware problem with the transmitter. Try turning the camera off, removing and reattaching the transmitter
and then turning the camera on again. If the problem persists, consult a Canon Service Center.
Check the network configuration.
- The camera could not connect to the network using the current settings. Check that the network settings are correctly
configured (A 164, 168).
Cover is open
- The card slot cover was opened while the recording media was being accessed. Stop the Wi-Fi function in use and
end the network connection.
FTP transfer error.
- An error occurred while transferring files to the FTP server. Turn then camera and the FTP server off and then on again
and try again the FTP transfer.
Incorrect Wi-Fi password.
- The authentication/encryption method is set to an option other than [Open/No encryption] and the password entered
is incorrect. Check the access point’s password and try entering the password again (A 167).
Troubleshooting
228
IP address conflict
- Another device on the same network has the same IP address assigned to the camera. Change the IP address of the
conflicting device or the camera.
LAN cable not connected.
- You attempted to connect to a wired network but the Ethernet cable is not connected. Check that the Ethernet cable is
correctly connected to the camera’s (Ethernet) terminal and to the LAN/Ethernet port on the network device.
Multiple access points detected. Try the operation again.
- There are multiple access points sending out a WPS signal at the same time. Try the operation again later or perform
setup using the [WPS: PIN Code] or [Search for Access Points] option (A 167).
No access points found
- The camera searched for active Wi-Fi networks (access points) in the area but none were found. Make sure the access
point is working correctly and try connecting again.
- The access point is operating in stealth mode. Deactivate the stealth function in the wireless router (access point)
settings.
- The camera may not be able to find the access point if MAC address filtering is activated. Check the camera’s (or
transmitter’s) MAC address with the [OPTIONS] > [Check MAC Address] setting from any network function’s screen.
Make sure to add this MAC address to the list of approved wireless devices in the wireless router (access point)
settings.
Reached the end of the adjustment range
- While adjusting the focus remotely using Browser Remote, the lens reached the proximal focus end or infinity focus
end.
Unable to complete WPS. Try the operation again.
- More than 2 minutes passed between activating WPS on the access point and pressing [OK]/pressing SET on the
camera. Start over the WPS procedure from the beginning.
- The WPS button was not held down long enough. Refer to the instruction manual of your wireless router. When using
WPS to make a wireless connection, keep the WPS button held down until the wireless router’s WPS function is
activated.
- Turn off the camera and access point, turn them back on again and then start over the WPS procedure from the
beginning. If this does not solve the problem, try using the [Search for Access Points] option (A 167).
- The access point’s encryption method is set to WEP. Wi-Fi Protected Setup (WPS) cannot connect to access points
set to this encryption method. Change the access point’s encryption method or use another connection method
(A 164).
Unable to connect
- Could not connect to the access point or network device selected.
- Cordless phones, microwave ovens, refrigerators and other appliances may interfere with the wireless signal. Try using
the camera in a location farther away from such appliances.
Unable to connect to FTP server.
- Could not connect to the indicated FTP server. Check the FTP server settings (A 185).
Unable to obtain an IP address
- If you are not using a DHCP server, enter the IP address manually (A 169).
- Turn on the DHCP server. If it is already on, make sure it is functioning properly.
- Make sure the address range for the DHCP server is sufficient.
WFT’s temperature too high. Cannot use Wi-Fi.
- Wi-Fi functions have been turned off because the transmitter’s temperature is too high. Remove the transmitter from
the camera and let it cool down before attaching it again.
Wi-Fi authentication unsuccessful
- Check the access point’s authentication/encryption method and password (encryption key) and change the camera
Wi-Fi settings (A 164) as necessary.
Wi-Fi error. Incorrect authentication method.
- Check the access point’s authentication/encryption method and change the camera Wi-Fi settings (A 164) as
necessary.
Wi-Fi error. Incorrect encryption method.
- Make sure the camera and access point are using the same authenticatio
n
/encryption method.
229
Handling Precautions and Safety Instructions
Handling Precautions and Safety Instructions
Be sure to read these instructions in order to operate the product safely. Follow these instructions to prevent
injury or harm to the operator of the product or others.
WARNING
Denotes the risk of serious injury or death.
Stop using the product in any case of unusual circumstances such as the presence of smoke or a strange
smell.
Do not touch any exposed internal parts.
Do not get the product wet. Do not insert foreign objects or liquids into the product.
Do not touch the product connected to a power outlet during lightning storms. This may cause electric shock.
Do not disassemble or modify the product.
Do not expose the product to strong shocks or vibration.
Use only power sources specified in this instruction manual
for use with the product.
Do not use the product if the power plug is not fully inserted into the power outlet.
Do not unplug the product by pulling the power cord.
Do not plug in or unplug the product with wet hands.
Do not place heavy objects on the power cord. Do not damage, break or modify the power cord.
Do not leave the product connected to a power source for long periods of time.
Observe the following instructions when using commercially available batteries or provided battery packs.
- Do not use leaking batteries/battery packs. If a battery/battery pack leaks and the material contacts your
skin or clothing, flush the exposed area thoroughly with running water. In case of eye contact, flush
thoroughly with copious amounts of clean running water and seek immediate medical assistance.
- Do not heat batteries or expose them to fire.
- Do not expose the terminals to dirt or let them come into contact with metallic pins or other metal objects.
Do not look through the viewfinder at strong light sources such as the sun on a bright day or lasers and other
strong artificial light sources.
Do not leave a lens or a camera/camcorder with a lens attached, exposed without the lens cap attached. The
lens may concentrate the light and cause fire.
Do not wrap the product in cloth or other materials when in use or shortly after use when the product is still
warm in temperature.
Do not allow the product to maintain contact with the same area of skin for extended periods of time during
use. This may result in low-temperature contact burns, including skin redness and blistering, even if the
product does not feel hot. The use of a tripod or similar equipment is recommended when using the product in
hot places and for people with circulation problems or less sensitive skin.
Keep the product out of the reach of young children.
Periodically remove any dust buildup from the power plug and power outlet using a dry cloth.
Follow any indications to turn off the product in places where its use is forbidden. Not doing so may cause
other equipment to malfunction due to the effect of electromagnetic waves and even result in accidents.
CAUTION
Denotes the risk of injury.
Do not leave the product in places exposed to extremely high or low temperatures. The product may become
extremely hot/cold and cause burns or injury when touched.
Only mount the product on a tripod that is sufficiently sturdy.
Handling Precautions and Safety Instructions
230
Camera
Do not use or store the camera in dusty or sandy places. The camera is not waterproof – avoid also water,
mud or salt. If any of the above should get into the camera it may damage the camera and/or the lens. Consult
a Canon Service Center as soon as possible.
Be careful to avoid dust and dirt particles accumulating on the lens or entering the camera. When you finish
using the camera, make sure to attach the body cap to the lens mount and the lens cap and dust cap to the
lens.
Do not use the camera near strong electromagnetic fields such as near powerful magnets and motors, MRI
machines or high-voltage power lines. Using the camera in such places may cause anomalies in the video, or
audio or video noise to appear.
Do not point the camera or optional viewfinder toward an intense light source, such as the sun on a sunny day
or an intense artificial light source. Doing so may damage the image sensor or the camera’s internal
components. Be careful especially when using a tripod. When you are not using the camera, make sure to
attach the lens cap to the lens.
Do not touch the lens contacts on the lens mount. Dirty contacts may cause a poor
contact between the camera and the lens resulting in incorrect operation of the
camera. After removing the lens, make sure to attach the body cap to the lens mount
and the lens cap and dust cap to the lens.
Long-term storage
If you do not intend to use the camera for a long time, store it in a place free of dust, in
low humidity, and at temperatures not higher than 30 °C (86 °F).
Power Sources
Dirty terminals may cause a poor contact between a battery and the camera. Wipe the terminals on the
supplied battery adapter for V-mount batteries with a soft dry cloth.
Lithium Button Battery
Do not pick up the battery using tweezers or other metal tools, as this will cause a short circuit.
Wipe the battery with a clean dry cloth to ensure proper contact.
For CA, USA only
Included lithium battery contains Perchlorate Material - special handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate/ for details.
WARNING!
The battery used in this device may present a fire or chemical burn hazard if mishandled.
Do not disassemble, modify, immerse in water, heat above 100 °C (212 °F) or incinerate the battery.
Do not insert the battery into the mouth. If swallowed, seek medical assistance immediately. The battery
case may break and the battery fluids may cause internal injuries.
Keep the battery out of the reach of children.
Do not recharge, short-circuit or insert the battery in the wrong direction.
Dispose of the used battery according to applicable recycling regulations. In Europe, the used battery
should be returned to the supplier for safe disposal.
231
Handling Precautions and Safety Instructions
Recording Media
We recommend backing up the recordings on the recording media onto your computer. Data may be
corrupted or lost due to defects or exposure to static electricity. Canon shall not be liable for lost or corrupted
data.
Do not touch or expose the terminals to dust or dirt.
Do not use recording media in places subject to strong magnetic fields.
Do not leave recording media in places subject to high humidity and high temperature.
Do not disassemble, bend, drop, or subject recording media to shocks and do not expose them to water.
Check the direction before inserting the recording media. Forcing recording media into the slot if it is not
correctly oriented may damage the recording media or the camera.
Do not attach any labels or stickers on the recording media.
Disposal
When you delete data on the recording media, only the file allocation table is altered and stored data is not
physically erased. Take the necessary precautions when you dispose of the recording media, for example by
physically damaging it to prevent the leakage of private data.
If giving the recording media to another person, initialize it (using the [Complete] initialization option for SD cards,
A 51). Fill it up with unimportant recordings, and then initialize it again. This makes recovering the original
recordings very difficult.
Maintenance/Others
232
Maintenance/Others
Cleaning
Camera body
Use a soft, dry cloth to clean the camera’s body. Never use chemically treated cloths or volatile solvents such
as paint thinner.
Lens
Remove any dust or dirt particles using a non-aerosol type blower brush.
Use a clean, soft lens-cleaning cloth to gently wipe the lens. Never use tissue paper.
Control display
Clean the screen using a clean, soft lens-cleaning cloth and commercially available cleaning fluid for
eyeglasses.
Condensation may form on the surface of the screen when the temperature changes suddenly. Wipe it with a
soft dry cloth.
Condensation
Moving the camera rapidly between hot and cold temperatures may cause condensation (water droplets) to form
on its internal surfaces. Stop using the camera if condensation is detected. Continued use may damage the
camera.
Condensation may form in the following cases:
When the camera is moved quickly from cold to warm places
When the camera is left in a humid room
When a cold room is heated rapidly
To avoid condensation
Do not expose the camera to sudden or extreme changes in temperature.
Remove the recording media and battery. Then, place the camera in an airtight plastic bag and let it adjust
gradually to temperature changes before removing it from the bag.
When condensation is detected
The precise time required for water droplets to evaporate will vary depending on the location and weather
conditions. As a general rule, wait for 2 hours before resuming use of the camera.
233
Optional Accessories
Optional Accessories
The following optional accessories are compatible with this camera. The availability differs from area to area.
For our customers in the USA: Call or visit your local retailer/dealer for genuine Canon video accessories. You
can also obtain genuine accessories for your Canon camera by calling: 1-800-828-4040, Canon U.S.A.
Information Center.
EVF-V70 OLED
Electronic Viewfinder
UN-5 (50 cm, 1.6 ft.) or
UN-10 (1 m, 3.3 ft.) Unit Cable
WFT-E6 or WFT-E8
Wireless File Transmitter
OU-700 Remote
Operation Unit
UC-V75 (75 cm, 2.5 ft.) or
UC-V1000 (10 m, 32.8 ft.)
Remote Operation Unit Cable
GP-E1 GPS Receiver
SG-1 Shoulder Style
Grip Unit
SU-15 Shoulder Support Unit
RR-10 (10 m, 32.8 ft.) or
RR-100 (100 m, 328 ft.)
8-pin Remote Cable
RC-V100
Remote Controller
MO-4E or MO-4P
B4 Mount Adapter
Optional Accessories
234
NOTES
You can have the camera’s EF lens mount with Cinema Lock replaced by a PL lens mount. For details, consult
the retail dealer from whom you purchased the camera or contact a Canon Service Center.
You can have the C700 / C700 PL / C700 FF / C700 FF PL model changed into a C700 GS PL model. For
details, consult the retail dealer from whom you purchased the camera or contact a Canon Service Center.
You can have the CMOS sensor of the C700 / C700 PL / C700 GS PL model changed to a full-frame sensor.
For details, consult the retail dealer from whom you purchased the camera or contact a Canon Service Center.
This mark identifies genuine Canon video accessories. When you use Canon video equipment, we
recommend Canon-brand accessories or products bearing the same mark.
235
Specifications
Specifications
C700 / C700 PL / C700 GS PL / C700 FF / C700 FF PL
System
•Recording System
Movies: Video compression: MPEG-4 AVC/H.264, Intra-frame or Long GOP
Apple ProRes
Audio compression: Linear PCM, 24 bit, 48 kHz, 4 channels
File format: MXF, Apple QuickTime File Format
Photos: DCF (Design rule for Camera File system), compatible with Exif Ver. 2.3, JPEG compression
Video Configuration (recording/playback)
Recordings on the CFast card:
Format: XF-AVC (main recording/sub recording), ProRes (main recording)
Bit rate (XF-AVC): 810 Mbps, 440 Mbps, 410 Mbps, 360 Mbps, 310 Mbps, 225 Mbps,
210 Mbps, 170 Mbps, 160 Mbps, 90 Mbps (Intra-frame); 50 Mbps (Long GOP)
Codec (ProRes): Apple ProRes 4444, ProRes 422 HQ, ProRes 422
Resolution: 4096x2160, 3840x2160, 2048x1080, 1920x1080
Color sampling: YCbCr 4:2:2, 10 bit; RGB 4:4:4, 12 bit / 10 bit
Frame rate: 59.94P, 59.94i, 50.00P, 50.00i, 29.97P, 23.98P, 25.00P, 24.00P
Recordings on the SD card:
Format: XF-AVC Proxy (sub recording)
Bit rate: 35 Mbps, 24 Mbps (Long GOP)
Resolution: 2048x1080, 1920x1080
Color sampling: YCbCr 4:2:0, 8 bit
Frame rate: 59.94P, 59.94i, 50.00P, 50.00i, 29.97P, 23.98P, 25.00P, 24.00P
Recording Media (not included)
For approximate recording times, refer to
Approximate Recording Times
(A 247)
Main recording/sub recording: CFast 2.0 card (2 slots)
Sub recording and photos
1
: SD, SDHC (SD High Capacity) or SDXC (SD eXtended Capacity) memory card
1
Custom picture files, camera settings and user memo files can be saved on and read from the SD card as well.
Image Sensor
Z[
Super 35mm-equivalent CMOS sensor
]
Super 35mm-equivalent CMOS sensor with global electronic shutter
qr Full-frame CMOS sensor
Effective pixels:
When the resolution is 4096x2160 or 2048x1080:
Z[] approx. 8,850,000 pixels (4096x2160)
qr approx. 18,690,000 pixels (5952x3140)*
When the resolution is 3840x2160 or 1920x1080:
Z[] approx. 8,290,000 pixels (3840x2160)
qr approx. 17,520,000 pixels (5580x3140)*
When the main recoding format is [RAW ( Capture Drive)]:
Z[
approx. 10,720,000 pixels (4512x2376)
]
approx. 10,150,000 pixels (4272x2376)
qr approx. 18,690,000 pixels (5952x3140)
* When the sensor mode is set to [Full Frame].
Control Display
7.66 cm (3.0 in.) color LCD, approx. 1,036,000 dots, aspect ratio 3:2
Specifications
236
Lens Mount
Zq
Canon EF mount with Cinema Lock compatible with Canon EF lenses (including EF-S lenses
and EF Cinema lenses)
[]r
PL mount compatible with Canon EF Cinema lenses with PL mount and
Cooke’s /i Technology
Lens multiplication factor for 35mm equivalent focal length (approximate):
qr
Sensor mode set to [Full Frame]
When the horizontal resolution is 3840/1920: 1.056
When the resolution is 5952x2532: 1.045
For all other cases: 1.000
Sensor mode set to [Super 35mm] or [Super 35mm (Cropped)]
When the resolution is 4096x2160, 2048x1080: 1.460
When the resolution is 3840x2160, 1920x1080: 1.534
Lens Correction
Peripheral illumination/chromatic aberration correction is available for Canon EF lenses, EF Cinema lenses and
broadcast lenses
2
2
Some lenses are not compatible with in-camera correction.
Shutter Speed
Speed (1/3-stop increments or 1/4-stop increments), angle, clear scan, slow, off
•Iris
Manual (1/2-stop increments or 1/3-stop increments, fine adjustment available), push auto iris,
automatic aperture
ISO Speed
Z[qr
ISO 100 to ISO 102400
]
ISO 400 to ISO 102400
(1-stop or 1/3-stop increments)
•Gain
Z[qr
–6 dB to 54 dB,
]
–6 dB to 42 dB (3-dB increments),
Z[qr
–2 dB to 54 dB,
]
–2 dB to 42 dB (fine adjustment in 0.5-dB
increments)
•ND Filter: Built-in (Off, 2, 4, 6, 8 or 10 stops), motor operated
•Exposure: AE shift, light metering modes (standard, spotlight, backlight)
White Balance
Auto white balance (AWB); custom white balance (2 sets, A and B); user-set white balance (5 settings,
2,000 K to 15,000 K); two preset settings (daylight, 5,600 K
3
and tungsten lamp, 3,200 K
3
)
Color temperature and color compensation (CC) adjustment available for all settings except AWB.
3
Color temperatures are approximate and given for reference purposes only.
Focus
Manual focus
Zq
only: Also autofocus (one-shot AF, AF-boosted MF, continuous AF); face AF and subject
tracking available
Zq
AF type: Dual Pixel CMOS AF, contrast-detection AF
Sensor Sensitivity (2000 lux, 89.9% reflection)
Z[qr
59.94 Hz: F10 (2048x1080 at 59.94P, ISO 800)
50.00 Hz: F11 (2048x1080 at 50.00P, ISO 800)
]
59.94 Hz: F20 (2048x1080 at 59.94P, ISO 1600)
50.00 Hz: F22 (2048x1080 at 50.00P, ISO 1600)
237
Specifications
S/N Ratio (Typical, using Canon Log 2, 1600% dynamic range)
Z[qr
68 dB (1920x1080 at 29.97P (59.94 Hz) or 25.00P (50.00 Hz), ISO 800)
]
67 dB (1920x1080 at 29.97P (59.94 Hz) or 25.00P (50.00 Hz), ISO 3200)
Subject Illumination (ISO 25600, with a f/1.2 lens, 100% output)
59.94 Hz: 0.45 lux (shutter speed 1/30)
50.00 Hz: 0.38 lux (shutter speed 1/25)
Built-In Microphone: Monaural electric condenser microphone
Size of Photos: 2048x1080, 2048x872, 1920x1080
Terminals
SDI OUT Terminals (SDI OUT 1 to SDI OUT 4) / MON. Terminals (MON. 1 and MON. 2)
BNC jack, output only, 0.8 Vp-p / 75 , unbalanced
3G-SDI: SMPTE 424, SMPTE 425, SMPTE ST 299-2
HD-SDI: SMPTE 292, SMPTE ST 299-1
Embedded audio, time code (VITC/LTC)
LUT (BT.709, BT.2020, DCI, ACESproxy, HDR-PQ, HDR-HLG, User LUT 1 to 4) and supplemental displays*
(superimposed onscreen displays, peaking, zebra pattern, magnification, B&W image, waveform monitor, false
color display, anamorphic desqueeze) can also be output.
* MON. terminals only.
•HDMI OUT Terminal
HDMI connector, output only
LUT (BT.709, BT.2020, DCI, ACESproxy, HDR-PQ, HDR-HLG, User LUT 1 to 4) and supplemental displays
(superimposed onscreen displays, peaking, zebra pattern, magnification, B&W image, waveform monitor, false
color display, anamorphic desqueeze) can also be output.
VIDEO Terminal
Proprietary connector for the optional EVF-V70 OLED Electronic Viewfinder, output only
LUT (BT.709, HDR (1600% or 400%), User LUT 1 to 4) and supplemental displays (superimposed onscreen
displays, peaking, zebra pattern, magnification, B&W image, waveform monitor, false color display,
anamorphic desqueeze) can also be output.
INPUT Terminals (INPUT 1 and INPUT 2)
XLR 3-pin jack (pin1: shield, pin2: hot, pin3: cold), 2 sets, balanced
Analog Inputs
Sensitivity:
MIC setting: –60 dBu (volume center, full scale –18 dB) / 600
LINE setting: 4 dBu (volume center, full scale –18 dB) / 10 k
Microphone attenuator: 20 dB
Digital Inputs (AES/EBU)
AES3 standard (48 kHz, 24 bit, 2ch) / 110
•MIC Terminal
3.5 mm stereo mini-jack, –72 dBV (volume center, full scale –18 dB) / 1.2 k
Microphone attenuator: 20 dB
×
(Headphone) Terminal
3.5 mm stereo mini-jack, –G to –8 dBV (16 load, volume range Min to Max) / 50 or less
GENLOCK/SYNC OUT Terminal
BNC jack, 1.0 Vp-p / 75
GENLOCK setting: input only; SYNC OUT setting: output only, tri-level HD signal
Specifications
238
TIME CODE IN/OUT Terminal
BNC jack, input/output
Input setting: 0.5 Vp-p to 18 Vp-p / 100 k;Output setting: 1.3 Vp-p / 50 or less
REMOTE A Terminal, REMOTE B Terminal
REMOTE A: 2.5 mm stereo sub-mini jack
REMOTE B: Circular 8-pin jack (for the optional RC-V100 Remote Controller, RS-422 interface)
CTRL Terminal
LEMO circular 7-pin jack (for the optional OU-700 Remote Operation Unit)
(Ethernet) Terminal
Ethernet, 1000BASE-T compatible
LENS Terminal
Circular 12-pin jack (12-pin serial interface)
System Extension Terminal
Proprietary connector for optional accessories
Power/Others
Compatible Batteries
V-mount batteries, 12 V to 20 V DC
DC IN 12V Terminal
XLR 4-pin jack (male connector), 11.5 V to 20 V DC,
10 A (acceptable maximum load current)
DC OUT 24V 2A Terminal
Fischer 3-pin connector, rated output: 24 V DC,
maximum current: 2.0 A
DC OUT 12V 2A Terminal
LEMO 2-pin connector, rated output: 12 V DC,
maximum current: 2.0 A
D-TAP Terminal
D-Tap connector, maximum output: 50 W (nominal)
Power Consumption
(using the EF24-70mm f/2.8L II USM lens, with the optional viewfinder connected and activated, video
output from the SDI OUT terminals and MON. terminals activated, and without supplying power to other
accessories*)
XF-AVC, 4K recording at 59.94P or 50.00P:
Z[] approx. 49.3 W, qr approx. 50.5 W
ProRes422 HQ, 4K recording at 29.97P or 25.00P:
Z[] approx. 59.1 W, qr approx. 61.0 W
* When the camera is powering external accessories, power consumption will increase by the amount consumed by the
connected accessories.
Operating Temperature: 0 – 40 °C (32 – 104 °F)
GND (ground)
N/A
11.5 V to 20 V
DC
N/A
N/A
GND (ground)
+24 V DC
GND (ground)
+12 V DC
Polarity +
Polarity –
239
Specifications
Dimensions (W x H x D)*
Camera body only:
Zq
167 x 154 x 327 mm (6.6 x 6.1 x 1.1 in.),
[]r
167 x 154 x 336 mm (6.6 x 6.1 x 1.1 in.)
For detailed technical drawings see the appendix
Camera Dimensions
(A 242).
* All dimensions are approximate.
•Weight **
Camera body only:
Z
3,440 g (7.6 lb.),
[]
3,600 g (7.9 lb.)
q 3,450 g (7.6 lb.), r 3,610 g (8.0 lb.)
Camera with handle, clamp base and microphone holder:
Z
3,900 g (8.6 lb.),
[]
4,060 g (9.0 lb.)
q 3,910 g (8.6 lb.)
r 4,070 g (9.0 lb.)
**All weights are approximate.
CDX-36150 Recorder (commercially available)
•Recording System
Video: Cinema RAW, Apple ProRes
Audio compression: Linear PCM, 24 bit, 48 kHz, 4 channels
Recording/Playback Signal
Cinema RAW:
Resolution: qr 5952x3140, qr 5952x2532,
Z[ 4512x2376, ] 4272x2376,
Z[ 4512x1920, 4096x2160, 2048x1080
Maximum frame rate: Z[] 240P, qr 168P
Apple ProRes:
Resolution: 4096x2160, 3840x2160, 2048x1080, 1920x1080
Codec: Apple ProRes 4444 XQ, ProRes 4444, ProRes 422 HQ,
qr ProRes422
Maximum frame rate: Z[] 240P, qr 168P
Recording Media (not included)
Codex Capture Drive 2.0
Weight and dimensions are approximate. Errors and omissions excepted.
Appendix: Compatible Lenses and Functions
240
Appendix: Compatible Lenses and Functions
Following is a list of lenses compatible with this camera and the various functions that can be used depending
on the lens. Depending on the lens’s purchase date, you may need to update the lens’s firmware to use these
functions. For details, consult a Canon Service Center.
1
Optional MO-4E or MO-4P B4 Mount Adapter.
2
If the lens’s drive unit is powered from an independent power source, the connection to the camera is not required.
3
Zq
only.
Broadcast lenses:
Lens
12-pin
interface
cable
B4 mount
adapter
1
Iris control from the camera Zoom control
from the
camera
Manual Push auto iris Automatic
EF lenses Ü Ü
EF lenses compatible with auto iris Ü Ü Ü
EF Cinema lenses
CN7x17 KAS S/E1 Required
2
Ü Ü Ü Ü
CN7x17 KAS S/P1 Required Ü Ü Ü Ü
CN20x50 IAS H/E1 Required
2
Ü Ü Ü Ü
CN20x50 IAS H/P1 Required Ü Ü Ü Ü
CN-E18-80mm T4.4 L IS KAS S,
CN-E70-200mm T4.4 L IS KAS S
Ü Ü Ü Ü
Prime lenses compatible with
Dual Pixel Focus Guide
Broadcast lenses Required Required Ü Ü Ü Ü
Lens
Focus control from the camera
Focus guide
3
Manual One-shot AF
3
Continuous
AF
3
Face AF
3
Tracking
3
EF lenses Ü Ü Ü Ü Ü Ü
EF lenses compatible with auto iris Ü Ü Ü Ü Ü Ü
EF Cinema lenses
CN7x17 KAS S/E1 Ü Ü Ü Ü Ü Ü
CN7x17 KAS S/P1 Ü
CN20x50 IAS H/E1 Ü
CN20x50 IAS H/P1 Ü
CN-E18-80mm T4.4 L IS KAS S,
CN-E70-200mm T4.4 L IS KAS S
Ü Ü Ü Ü Ü Ü
Prime lenses compatible with
Dual Pixel Focus Guide
Ü
Broadcast lenses Ü
CJ14ex4.3B IRSE S / IASE S
CJ18ex7.6B IRSE S / IASE S
CJ24ex7.5B IRSE S / IASE S
CJ45ex9.7B IASE-V H
CJ45ex13.6B IASE-V H
HJ14ex4.3B IASE S
HJ17ex7.6B IASE S
HJ18ex7.6B IASE S
HJ22ex7.6B IASE S
HJ24ex7.5B IASE S
241
Appendix: Compatible Lenses and Functions
EF lenses compatible with auto iris:
Prime lenses compatible with the Dual Pixel Focus Guide function:
EF24-105mm f/3.5-5.6 IS STM EF-S18-55mm f/4-5.6 IS STM
EF70-200mm f/4L IS II USM EF-S18-135mm f/3.5-5.6 IS STM
EF70-300mm f/4-5.6 IS II USM EF-S18-135mm f/3.5-5.6 IS USM
EF85mm f/1.4L IS USM EF-S35mm f/2.8 MACRO IS STM
EF-S10-18mm f/4.5-5.6 IS STM EF-S55-250mm f/4-5.6 IS STM
EF-S18-55mm f/3.5-5.6 IS STM
CN-E14mm T3.1 L F CN-E50mm T1.3 L F
CN-E20mm T1.5 L F CN-E85mm T1.3 L F
CN-E24mm T1.5 L F CN-E135mm T2.2 L F
CN-E35mm T1.5 L F
Appendix: Camera Dimensions
242
Appendix: Camera Dimensions
All measurements are in mm (inch measurements are given in parentheses).
100.8 (4.0 in.)
Left side view
Zq
Front view
Zq
66.5 (2.6 in.)
89.8 (3.5 in.)
53.8 (2.1 in.)
64.0 (2.5 in.) 84.0 (3.3 in.)
314.8 (1.0 ft.)11.7 (0.46 in.)
Lens mount surface
100.8 (4.0 in.)
Left side view
[]r
Front view
[]r
66.5 (2.6 in.)
89.8 (3.5 in.)
64.0 (2.5 in.) 84.0 (3.3 in.)
322.8 (1.1 ft.)13.0 (0.51 in.)
Right side view Back view
314.8 (1.0 ft.) 11.7 (0.46 in.)
Lens mount surface
243
Appendix: Camera Dimensions
Top view
25.4
(1.0 in.)
44.0
(1.7 in.)
12.7
(0.5 in.)
56.7
(2.2 in.)
118.0
(4.6 in.)
25.4
(1.0 in.)
25.4
(1.0 in.)
76.7
(3.0 in.)
25.4
(1.0 in.)
25.4
(1.0 in.)
25.4
(1.0 in.)
25.4
(1.0 in.)
25.4
(1.0 in.)
25.4
(1.0 in.)
25.4
(1.0 in.)
12.7
(0.5 in.)
25.4
(1.0 in.)
25.4
(1.0 in.)
25.4
(1.0 in.)
25.4
(1.0 in.)
25.4
(1.0 in.)
25.4
(1.0 in.)
Bottom view
12.7
(0.5 in.)
221.8 (8.7 in.)
12.7
(0.5 in.)
44.0
(1.7 in.)
12.7 (0.5 in.)
25.4 (1.0 in.)
211.2 (8.3 in.)
107.5 (4.2 in.)
25.4 (1.0 in.)
12.7 (0.5 in.)
50.4 (2.0 in.)
12.7
(0.5 in.)
25.4
(1.0 in.)
25.4
(1.0 in.)
12.7
(0.5 in.)
12.7
(0.5 in.)
12.7
(0.5 in.)
Appendix: Camera Dimensions
244
Front view (with accessories)
166.5 (6.6 in.) 203.8 (8.0 in.)
169.7 (6.7 in.)
245
Appendix: Camera Dimensions
Right side view (with accessories)
Microphone holder
275.9 (10.9 in.) max.
231.0 (9.1 in.)111.0 (4.4 in.)
38.1
(1.5 in.)
9.4 (0.37 in.)122.5 (4.8 in.)
73.5 (2.9 in.)
64.2 (2.5 in.) 9.5 (0.37 in.)
25.3 (1.0 in.)
28.4 (1.1 in.)
53.8 (2.1 in.)
Appendix: Camera Dimensions
246
Handle unit and clamp base
60.0
(2.4 in.)
25.4
(1.0 in.)
35.1
(1.4 in.)
35.1
(1.4 in.)
25.4
(1.0 in.)
25.4
(1.0 in.)
83.1 (3.3 in.)
70.6 (2.8 in.)
44.1
(1.7 in.)
11.2 (0.44 in.)
143.2 (5.6 in.)
73.5 (2.9 in.)
59.8 (2.4 in.)
30.5 (1.2 in.)
4.4 (0.17 in.)
18.2 (0.72 in.)
49.0
(1.9 in.)
4.4 (0.17 in.)
59.8 (2.4 in.)
30.5 (1.2 in.)
25.4
(1.0 in.)
25.4
(1.0 in.)
35.1
(1.4 in.)
12.7 (0.5 in.)
25.4
(1.0 in.)
25.4
(1.0 in.)
25.4
(1.0 in.)
25.4
(1.0 in.)
25.4
(1.0 in.)
25.4
(1.0 in.)
25.4
(1.0 in.)
25.4
(1.0 in.)
35.1
(1.4 in.)
25.4
(1.0 in.)
247
Approximate Recording Times
Approximate Recording Times
Recordings on the CFast card (XF-AVC clips)
Recordings on the CFast card (ProRes clips)
Recordings on the SD card (XF-AVC Proxy clips)
Bit rate 64 GB 128 GB 256 GB
[810 Mbps Intra-frame] 10 min. 20 min. 40 min.
[440 Mbps Intra-frame] 15 min. 35 min. 75 min.
[310 Mbps Intra-frame] 25 min. 50 min. 105 min.
[225 Mbps Intra-frame] 35 min. 75 min. 150 min.
[160 Mbps Intra-frame] 50 min. 105 min. 210 min.
[50 Mbps Long GOP] 165 min. 335 min. 680 min.
Resolution Frame rate Codec 64 GB 128 GB 256 GB
4096x2160
29.97P
ProRes 422 HQ
5 min. 15 min. 35 min.
24.00P, 23.98P 10 min. 20 min. 40 min.
25.00P 10 min. 20 min. 40 min.
2048x1080
59.94P
ProRes 4444
10 min. 20 min. 40 min.
29.97P 20 min. 40 min. 85 min.
24.00P, 23.98P 25 min. 55 min. 110 min.
50.00P 10 min. 25 min. 50 min.
25.00P 25 min. 50 min. 105 min.
SD card capacity
Bit rate
16 GB 32 GB
[35 Mbps Long GOP] 60 min. 120 min.
[24 Mbps Long GOP] 85 min. 175 min.
Approximate Recording Times
248
Recordings using the commercially available CDX-36150 (on a 2 TB Capture Drive 2.0, for reference only)
* When the frame rate is set to 29.97P or 25.00P, the approximate recording time will be about twice that for 59.97P or 50.00P,
respectively. When the frame rate is set to 23.98P, the approximate recording time will be at a par with that for 24.00P.
Main recording video configuration
Approximate recording time
Main recording format Resolution Frame rate*
[RAW ( Capture Drive)]
5952x3140
59.94P 21 min.
24.00P 46 min.
50.00P 25 min.
5952x2532
59.94P 26 min.
24.00P 58 min.
50.00P 31 min.
4512x2376
59.94P 32 min.
24.00P 81 min.
50.00P 39 min.
4272x2376
59.94P 34 min.
24.00P 86 min.
50.00P 41 min.
4512x1920
59.94P 40 min.
24.00P 100 min.
50.00P 48 min.
4096x2160
59.94P 39 min.
24.00P 98 min.
50.00P 47 min.
[ProRes ( Capture Drive)]
4096x2160
ProRes 422 HQ, 10 bit
59.94P 67 min.
24.00P 169 min.
50.00P 81 min.
3840x2160
ProRes 422 HQ, 10 bit
59.94P 72 min.
24.00P 180 min.
50.00P 86 min.
2048x1080
ProRes 4444 XQ, 12 bit
59.94P 113 min.
24.00P 282 min.
50.00P 135 min.
2048x1080
ProRes 422 HQ, 10 bit
59.94P 254 min.
24.00P 636 min.
50.00P 305 min.
1920x1080
ProRes 4444 XQ, 12 bit
59.94P 129 min.
24.00P 322 min.
50.00P 154 min.
1920x1080
ProRes 422 HQ, 10 bit
59.94P 290 min.
24.00P 726 min.
50.00P 348 min.
249
(Ethernet) terminal . . . . . . . . . . . . . . . . . . .168
×
(headphones) terminal
. . . . . . . . . . . . . . .113
4K workflow . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
A
ABB (automatic black balance) . . . . . . . . . . . . .54
Access point . . . . . . . . . . . . . . . . . . . . . .163, 165
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . .233
ACES color, ACESproxy . . . . . . . . . . . . . .22, 155
AE shift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
Air vents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
ALT (alternative) screen . . . . . . . . . . . . . . .30, 188
Anamorphic lenses and desqueeze . . . . . . . . .122
Aperture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
Automatic aperture (auto iris) . . . . . . . . .81
Push auto iris . . . . . . . . . . . . . . . . . . . . .81
Area of use (Wi-Fi) . . . Areas of Use and Restrictions*
Assignable buttons . . . . . . . . . . . . . . . . . . . . .127
Audio limiter . . . . . . . . . . . . . . . . . . . . . . . . . . .112
Audio output channels . . . . . . . . . . . . . . . . . . .160
Audio recording . . . . . . . . . . . . . . . . . . . . . . . .108
Audio recording level . . . . . . . . . . . . . . . . . . . .111
Audio reference signal . . . . . . . . . . . . . . . . . . .114
AWB (auto white balance) . . . . . . . . . . . . . . . . .87
AWB Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87
B
Batteries (main power supply) . . . . . . . . . . . . . .26
Battery adapter . . . . . . . . . . . . . . . . . . . . . . . . .26
Bit rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
Black balance . . . . . . . . . . . . . . . . . . . . . . . . . .54
Browser Remote . . . . . . . . . . . . . . . . . . . . . . .170
Built-in backup battery . . . . . . . . . . . . . . . . . . . .24
Button connection mode (WPS) . . . . . . . . . . . .166
C
Camera Access Point . . . . . . . . . . . . . . . . . . .165
Camera dimensions . . . . . . . . . . . . . . . . . . . . .242
Camera ID . . . . . . . . . . . . . . . . . . . . . . . . . . . .170
Camera level (electronic horizon) . . . . . . . . . . . .40
Camera menu . . . . . . . . . . . . . . . . . . . . . .32, 190
Camera settings . . . . . . . . . . . . . . . . . . . . . . . .140
Canon Log, Canon Log 2 gamma, Canon Log 3
(gamma curves) . . . . . . . . . . . . . . . . . .84, 134
Canon XF Utility (download) . . . . . . . . . . . . . . 161
CDX-36150 Recorder . . . . . . . . . . . . . . . . . . 203
CFast card
Compatible CFast cards . . . . . . . . . . . . 48
Initializing . . . . . . . . . . . . . . . . . . . . . . . 51
Inserting/Removing . . . . . . . . . . . . . . . . 49
Recording method . . . . . . . . . . . . . . . . 52
Switching CFast card slots . . . . . . . . . . 52
Check marks (%) . . . . . . . . . . . . . . . . . . 117, 146
Cinema RAW Development (download) . . . . . 161
Clamp base . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Clips
Adding an $ mark/% mark . . . . 117, 146
Clip information . . . . . . . . . . . . . . . . . . 145
Clip name format . . . . . . . . . . . . . . . . . 62
Deleting . . . . . . . . . . . . . . . . . . . . . . . 147
Playback . . . . . . . . . . . . . . . . . . . . . . . 142
Recording . . . . . . . . . . . . . . . . . . . . . . . 55
Recovering . . . . . . . . . . . . . . . . . . . . . . 53
XF-AVC Proxy clips . . . . . . . . . . . . . . . . 71
Color bars . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Color compensation (CC) value . . . . . . . . . . . . 88
Color sampling . . . . . . . . . . . . . . . . . . . . . . . . . 66
Color space . . . . . . . . . . . . . . . . . . . . . . . 84, 134
Condensation . . . . . . . . . . . . . . . . . . . . . . . . 232
Connection to external devices . . . . . . . . . . . 152
Control display . . . . . . . . . . . . . . . . . . . . . . . . . 30
CTRL terminal . . . . . . . . . . . . . . . . . . . . . . . . . 15
Custom displays . . . . . . . . . . . . . . . . . . . . . . 139
Custom picture . . . . . . . . . . . . . . . . . . . . . . . 131
Main settings . . . . . . . . . . . . . . . . . . . 134
Other settings . . . . . . . . . . . . . . . . . . . 135
Preset color settings . . . . . . . . . . . 84, 134
CUSTOM switch and control dial . . . . . . . . 77, 80
D
Date and time . . . . . . . . . . . . . . . . . . . . . . . . . 29
DC IN 12V terminal (main power supply) . . . . . 27
DC OUT terminals (power output for
accessories) . . . . . . . . . . . . . . . . . . . . . . . . 28
Developing RAW clips . . . . . . . . . . . . . . . . . . 161
Direct setting mode . . . . . . . . . . . . . . . . . . . . . 73
Double slot recording . . . . . . . . . . . . . . . . . . . . 52
Drop frame (time code) . . . . . . . . . . . . . . . . . 102
D-TAP terminal . . . . . . . . . . . . . . . . . . . . . . . . 28
Dual Pixel Focus Guide . . . . . . . . . . . . . . . . . . 90
Index
* Separate leaflet supplied with the optional WFT-E6 or WFT-E8 Wireless File Transmitter.
250
E
EF Cinema lenses . . . . . . . . . . . . . . . . . . . . . .240
EF lens mount . . . . . . . . . . . . . . . . . . . . . . . . . .44
Extension modules . . . . . . . . . . . . . . . . . . .23, 24
External recorder . . . . . . . . . . . . . . . . . . . . . . .152
F
Face detection . . . . . . . . . . . . . . . . . . . . . . . . . .96
False color display . . . . . . . . . . . . . . . . . . . . . .100
Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
FEC error correction . . . . . . . . . . . . . . . . . . . .183
Focus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89
AF Lock . . . . . . . . . . . . . . . . . . . . . . . . .95
AF speed . . . . . . . . . . . . . . . . . . . . . . . .94
AF-Boosted MF . . . . . . . . . . . . . . . . . . .93
Continuous AF . . . . . . . . . . . . . . . . . . . .94
Face AF . . . . . . . . . . . . . . . . . . . . . . . . .96
Focus assistance functions . . . . . . . . . .90
Manual focus . . . . . . . . . . . . . . . . . . . . .90
One-shot AF . . . . . . . . . . . . . . . . . . . . . .92
Frame rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Free-run (time code) . . . . . . . . . . . . . . . . . . . .101
FTP transfer . . . . . . . . . . . . . . . . . . . . . . . . . . .185
G
Gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
Genlock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106
GENLOCK/SYNC OUT terminal . . . .105, 106, 107
GPS information . . . . . . . . . . . . . . . . . . .120, 180
H
Handle unit . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
HDMI OUT terminal . . . . . . . . . . . . . . . . .149, 154
HOME (home) screen . . . . . . . . . . . . . . . .30, 187
Hour meter . . . . . . . . . . . . . . . . . . . . . . . . . . .201
I
IEEE 802.11a/b/g/n (Wi-Fi specifications) . . . .164
INFO (information) screens . . . . . . . . . . . . . . . .215
Infrastructure . . . . . . . . . . . . . . . . . . . . . . . . . .165
Initializing recording media . . . . . . . . . . . . . . . . .51
INPUT terminals . . . . . . . . . . . . . . . . . . . .108, 110
Intra-frame (XF-AVC compression) . . . . . . . . . . .66
IP streaming . . . . . . . . . . . . . . . . . . . . . . . . . .182
Iris . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79
ISO speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
J
Joystick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
K
Key lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
L
Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Lens correction (chromatic aberration/
peripheral illumination) . . . . . . . . . . . . . . . . .47
Lens firmware . . . . . . . . . . . . . . . . . . . . . . . . . .45
LENS terminal . . . . . . . . . . . . . . . . . . . . . . .44, 46
Light metering mode . . . . . . . . . . . . . . . . . . . . .82
Lithium button battery . . . . . . . . . . . . . . . . . . . .24
Long GOP (XF-AVC compression) . . . . . . . . . . .66
LUT (lookup table) . . . . . . . . . . . . . . . . . . . . . .155
M
MAC address . . . . . . . . . . . . . . . . . . . . . . . . .228
Magnification . . . . . . . . . . . . . . . . . . . . . . . . . . .92
Menu settings and setup screens . . . . . . . . . .187
Message list . . . . . . . . . . . . . . . . . . . . . . . . . . .224
Metadata . . . . . . . . . . . . . . . . . . . . . . . . . . . . .118
MIC terminal . . . . . . . . . . . . . . . . . . . . . . . . . .108
Microphone
Attenuator . . . . . . . . . . . . . . . . . . . . . .113
Built-in (monaural) . . . . . . . . . . . . . . . . .110
External . . . . . . . . . . . . . . . . . . . .109, 110
Low cut filter . . . . . . . . . . . . . . . . . . . . .113
Sensitivity . . . . . . . . . . . . . . . . . . . . . . .112
Microphone holder . . . . . . . . . . . . . . . . . . .43, 109
MON. terminals . . . . . . . . . . . . . . . . . . . .149, 153
Monitoring menu . . . . . . . . . . . . . . . . . . . .33, 190
My Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
* Separate leaflet supplied with the optional WFT-E6 or WFT-E8 Wireless File Transmitter.
251
N
ND filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78
Network connection
Wi-Fi . . . . . . . . . . . . . . . . . . . . . . . . . . .164
Wired (Ethernet) . . . . . . . . . . . . . . . . . .168
Network functions . . . . . . . . . . . . . . . . . . . . . .163
Non-drop frame (time code) . . . . . . . . . . . . . . .102
O
OK marks ($) . . . . . . . . . . . . . . . . . . . . .117, 146
Onscreen displays . . . . . . . . . . . . . . . .57, 59, 144
Onscreen markers . . . . . . . . . . . . . . . . . . . . . . .98
On-set color grading . . . . . . . . . . . . . . . . . . . . .22
P
Peaking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91
Phantom power (microphone) . . . . . . . . . . . . .110
Photos
Deleting . . . . . . . . . . . . . . . . . . . . . . . .147
Photo numbering . . . . . . . . . . . . . . . . .125
Recording . . . . . . . . . . . . . . . . . . . . . . .125
Viewing . . . . . . . . . . . . . . . . . . . . . . . . .143
PIN code connection mode (WPS) . . . . . . . . . .166
PL lens mount . . . . . . . . . . . . . . . . . . . . . . . . . .46
PLAY (playback) screen . . . . . . . . . . . . . .141, 190
Playback
Clips . . . . . . . . . . . . . . . . . . . . . . . . . . .142
Photos . . . . . . . . . . . . . . . . . . . . . . . . .143
Playback media/format . . . . . . . . . . . . .142
POWER button . . . . . . . . . . . . . . . . . . . . . . . . .28
Power level warnings . . . . . . . . . . . . . . . . . . . . .27
Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . .26
ProRes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
R
RAW video . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Rec run (time code) . . . . . . . . . . . . . . . . . . . . .101
Recording
Clips . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Photos . . . . . . . . . . . . . . . . . . . . . . . . .125
Simultaneous sub recordings . . . . . . . . .71
Recording times . . . . . . . . . . . . . . . . . . . . . . . .247
Recovering corrupted clips . . . . . . . . . . . . . . . .53
Relay recording . . . . . . . . . . . . . . . . . . . . . . . . .52
REMOTE A, REMOTE B terminals . . . . . . . . . 123
Remote controller . . . . . . . . . . . . . . . . . . . . . 123
Remote operation . . . . . . . . . . . . . . . . . 123, 170
Resetting all camera settings . . . . . . . . . . . . . 197
Resolution (frame size) . . . . . . . . . . . . . . . . . . . 66
Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
Running mode (time code) . . . . . . . . . . . . . . . 101
S
Safe area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Saving clips to a computer . . . . . . . . . . . . . . . 161
Screen buttons . . . . . . . . . . . . . . . . . . . . . . . . 30
SD card
Compatible SD cards . . . . . . . . . . . . . . 48
Initializing . . . . . . . . . . . . . . . . . . . . . . . 51
Inserting/Removing . . . . . . . . . . . . . . . . 50
SDI OUT terminals . . . . . . . . . . . . . . . . . 149, 152
Search for access points . . . . . . . . . . . . . . . . 167
Setup screens . . . . . . . . . . . . . . . . . . . . . 30, 187
Shooting frame rate . . . . . . . . . . . . . . . . . . . . . 68
Shutter speed . . . . . . . . . . . . . . . . . . . . . . . . . 74
Slow & fast motion recording . . . . . . . . . . . . . . 68
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 235
Synchronization . . . . . . . . . . . . . . . . . . . . . . . 105
System extension terminal . . . . . . . . . . . 120, 164
System frequency . . . . . . . . . . . . . . . . . . . . . . 65
T
Tally lamp . . . . . . . . . . . . . . . . . . . . . . . . . 55, 199
TC (time code) screen . . . . . . . . . . . . . . . 30, 189
Time code . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
TIME CODE IN/OUT terminal . . . . . . . . . 106, 107
Tracking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Tripod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . 219
Turning the camera on/off . . . . . . . . . . . . . . . . 28
U
User bit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
User LUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
User memo . . . . . . . . . . . . . . . . . . . . . . 118, 180
USER screen (customized setup screen) . . . . 130
User settings (user names/passwords for
Browser Remote) . . . . . . . . . . . . . . . . . . . 170
* Separate leaflet supplied with the optional WFT-E6 or WFT-E8 Wireless File Transmitter.
252
V
Video configuration . . . . . . . . . . . . . . . . . . . . . .65
Video output configuration . . . . . . . . . . . . . . . .149
VIDEO terminal . . . . . . . . . . . . . . . . . . . . . . . . .41
Viewfinder (optional EVF-V70) . . . . . . . . . . . . . .41
V-mount batteries . . . . . . . . . . . . . . . . . . . . . . .26
W
Waveform monitor . . . . . . . . . . . . . . . . . . . . . .115
White balance . . . . . . . . . . . . . . . . . . . . . . . . . .86
Wide DR . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134
Wi-Fi channel . . . . . . Areas of Use and Restrictions*
Wireless file transmitter . . . . . . . . . . . . . . . . . .164
WPS (Wi-Fi Protected Setup) . . . . . . . . . . . . . .166
Z
Zebra pattern . . . . . . . . . . . . . . . . . . . . . . . . . . .99
Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .179
* Separate leaflet supplied with the optional WFT-E6 or WFT-E8 Wireless File Transmitter.
253
CANON CINEMA EOS LIMITED WARRANTY FOR PRODUCTS PURCHASED IN THE UNITED
STATES
The limited warranty set forth below is given by Canon U.S.A., Inc. (‘Canon USA) with respect to (a) the Canon Cinema EOS Product, and (b) the accessories
for the Canon Cinema EOS Product (if any), packaged with this limited warranty (collectively the “Products”)* and purchased in the United States. This limited
warranty is only effective upon presentation of your Bill of Sale or other proof of purchase. The Products are warranted to the original end-user purchaser,
when delivered in new condition in its original container, under normal use against defective materials or workmanship as follows: Parts: At Canon USAs
option, defective parts will be exchanged for new parts or comparable rebuilt parts for a period of ONE YEAR from the date of original purchase. Labor: For a
period of ONE YEAR from the date of original purchase, labor will be provided free of charge by Canon USAs factory service centers or designated service
facilities located in the United States. When returning Products under this warranty, you must pre-pay the shipping charges, and you must enclose a copy of
the Bill of Sale or other proof of purchase with a complete explanation of the problem. During the ONE-YEAR warranty period, repairs will be made and the
Products will be return-shipped to you free of charge. For repairs after the warranty period is over, you will be given an estimate of the cost of repair and an
opportunity to approve or disapprove of the repair expense before it is incurred. If you approve, repairs will be made and the Products will be returned to you
at your risk and expense. If you disapprove, we will return-ship the Products to you at no charge to you to an address within the United States.
This limited warranty only applies if the Products are used in conjunction with compatible computer equipment and compatible software, as
to which items Canon USA will have no responsibility. Canon USA shall have no responsibility under this limited warranty for use of the
Products in conjunction with incompatible peripheral equipment and/or incompatible software. Non-Canon brand peripheral equipment and
software which may be distributed with, or factory loaded on, the Products, are sold ‘AS IS’ without warranty of any kind by Canon USA,
including any implied warranty regarding merchantability or fitness for a particular purpose. The sole warranty with respect to such non-
Canon brand items is given by the manufacturer or producer thereof.
* Except for the battery pack packaged with the Products, which carries a separate ninety (90) day limited warranty.
In order to obtain warranty service, please contact the authorized Canon retail dealer from whom you purchased the Products or contact the CANON
INFORMATION CENTER AT 855-CINE-EOS (855-246-3367) or on the internet at pro.usa.canon.com/support
. You will be directed to the nearest service
facility for your Products.
This Limited Warranty covers all defects encountered in normal use of the Products and does not apply in the following cases:
A. Loss or damage to the Products due to abuse, mishandling, accident, improper maintenance, use of non-Canon accessories or failure to follow
operating, maintenance or environmental instructions prescribed in Canon USAs user’s manual;
B. If the Products are defective as a result of leaking batteries, sand, dirt or water damage;
C. If defects or damages are caused by the use of parts or supplies (other than those sold by Canon USA) that cause damage to the Products or that
cause abnormally frequent service calls or service problems;
D. If defects or damages are caused by service other than Canon USA’s factory service centers or authorized service facilities;
E. Any internal modification to product hardware or firmware;
F. Any applicable fee for Maintenance of the Products;
G. If the Product has had its serial number or dating altered or removed.
This Limited Warranty does not apply to Products purchased outside the United States. This Limited Warranty does not apply to accessories or
consumables not originally packaged with the Product. Please retain this warranty card and your Bill of Sale as a permanent record of your purchase. This
card ensures that you are contacted promptly should there be a safety inspection, modification or Product recall under applicable laws or regulations.
NO IMPLIED WARRANTY, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE APPLIES TO THE PRODUCTS AFTER THE
APPLICABLE PERIOD OF EXPRESS WARRANTY OR GUARANTY (EXCEPT AS MENTIONED ABOVE) GIVEN BY ANY PERSON, FIRM OR CORPORATION
WITH RESPECT TO THE PRODUCTS SHALL BIND CANON USA (SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED
WARRANTY LASTS, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU). CANON USA SHALL NOT BE LIABLE FOR LOSS OF
REVENUES OR PROFITS, EXPENSE FOR SUBSTITUTE PRODUCTS OR SERVICE, STORAGE CHARGES, LOSS OR CORRUPTION OF DATA, INCLUDING
WITHOUT LIMITATION, LOSS OR CORRUPTION OF DATA STORED ON THE PRODUCTS’ HARD DRIVE, OR ANY OTHER SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE OR INABILITY TO USE THE PRODUCTS, REGARDLESS OF THE LEGAL THEORY ON
WHICH THE CLAIM IS BASED, AND EVEN IF CANON USA HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. NOR SHALL RECOVERY
OF ANY KIND AGAINST CANON USA BE GREATER THAN THE PURCHASE PRICE OF THE PRODUCTS SOLD BY CANON USA AND CAUSING THE
ALLEGED DAMAGE. WITHOUT LIMITING THE FOREGOING, YOU ASSUME ALL RISK AND LIABILITY FOR LOSS, DAMAGE OR INJURY TO YOU AND
YOUR PROPERTY AND TO OTHERS AND THEIR PROPERTY ARISING OUT OF USE, MISUSE OR INABILITY TO USE THE PRODUCTS NOT CAUSED
DIRECTLY BY THE NEGLIGENCE OF CANON USA (SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU).THIS LIMITED WARRANTY SHALL NOT EXTEND TO ANYONE
OTHER THAN THE ORIGINAL PURCHASER OF THE PRODUCTS OR THE PERSON FOR WHOM IT WAS PURCHASED AS A GIFT.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
CANON U.S.A., INC
USA
&
254
CANON CINEMA EOS LIMITED WARRANTY FOR PRODUCTS PURCHASED IN CANADA
The limited warranty set forth below is given by Canon Canada Inc. (‘Canon Canada’) with respect to (a) the Canon Cinema EOS product, and (b) the
accessories for the Canon Cinema EOS Product (if any), packaged with this limited warranty (collectively the “Products”)* and purchased in Canada. This
limited warranty is only effective upon presentation of your Bill of Sale or other proof of purchase. The Products are warranted to the original end-user
purchaser, when delivered in new condition in its original container, under normal use against defective materials or workmanship as follows: Parts: At
Canon Canada’s option, defective parts will be exchanged for new parts or comparable rebuilt parts for a period of ONE YEAR from the date of original
purchase. Labor: For a period of ONE YEAR from the date of original purchase, labor will be provided free of charge by Canon Canada’s factory service
center or designated service facilities located in Canada. When returning Products under this warranty, you must pre-pay the shipping charges, and you
must enclose a copy of the Bill of Sale or other proof of purchase with a complete explanation of the problem. During the ONE-YEAR warranty period,
repairs will be made and the Products will be return-shipped to you free of charge. For repairs after the warranty period is over, you will be given an
estimate of the cost of repair and an opportunity to approve or disapprove of the repair expense before it is incurred. If you approve, repairs will be made
and the Products will be returned to you at your risk and expense. If you disapprove, we will return-ship the Products to you at no charge to you to an
address within Canada.
This limited warranty only applies if the Products are used in conjunction with compatible computer equipment and compatible software, as to
which items Canon Canada will have no responsibility. Canon Canada shall have no responsibility under this limited warranty for use of the
Products in conjunction with incompatible peripheral equipment and/or incompatible software. Non-Canon brand peripheral equipment and
software which may be distributed with, or factory loaded on, the Products, are sold ‘AS IS’ without warranty of any kind by Canon Canada,
including any implied warranty or condition regarding merchantability or fitness for a particular purpose. The sole warranty with respect to such
non-Canon brand items is given by the manufacturer or producer thereof.
* Except for the battery pack packaged with the Products, which carries a separate ninety (90) day limited warranty.
In order to obtain warranty service, please contact the authorized Canon retail dealer from whom you purchased the Products or contact the CANON
PROFESSIONAL SERVICE CENTRE 1-800-667-2666 or on the internet at www.canon.ca/pro
. You will be directed to the nearest service facility for your
Products.
This Limited Warranty covers all defects encountered in normal use of the Products and does not apply in the following cases:
A. Loss or damage to the Products due to abuse, mishandling, accident, improper maintenance, use of non-Canon accessories or failure to follow
operating, maintenance or environmental instructions prescribed in Canon Canada’s user’s manual;
B. If the Products are defective as a result of leaking batteries, sand, dirt or water damage;
C. If defects or damages are caused by the use of parts or supplies (other than those sold by Canon Canada) that cause damage to the Products or
that cause abnormally frequent service calls or service problems;
D. If defects or damages are caused by service other than Canon Canada’s factory service centers or authorized service facilities;
E. Any internal modification to product hardware or firmware;
F. Any applicable fee for Maintenance of the Products;
G. If the Product has had its serial number or dating altered or removed.
This Limited Warranty does not apply to Products purchased outside Canada. This Limited Warranty does not apply to accessories or consumables not
originally packaged with the Product. Please retain this warranty card and your Bill of Sale as a permanent record of your purchase. This card ensures
that you are contacted promptly should there be a safety inspection, modification or Product recall under applicable laws or regulations.
NO IMPLIED WARRANTY OR CONDITION, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE APPLIES TO THE
PRODUCTS AFTER THE APPLICABLE PERIOD OF EXPRESS WARRANTY OR GUARANTY (EXCEPT AS MENTIONED ABOVE) GIVEN BY ANY PERSON,
FIRM OR CORPORATION WITH RESPECT TO THE PRODUCTS SHALL BIND CANON CANADA (SOME PROVINCES DO NOT ALLOW LIMITATIONS ON
HOW LONG AN IMPLIED WARRANTY OR CONDITION LASTS, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU). CANON
CANADA SHALL NOT BE LIABLE FOR LOSS OF REVENUES OR PROFITS, EXPENSE FOR SUBSTITUTE PRODUCTS OR SERVICE, STORAGE
CHARGES, LOSS OR CORRUPTION OF DATA, INCLUDING WITHOUT LIMITATION, LOSS OR CORRUPTION OF DATA STORED ON THE PRODUCTS’
HARD DRIVE, OR ANY OTHER SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE OR INABILITY TO USE THE
PRODUCTS, REGARDLESS OF THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF CANON CANADA HAS BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES. NOR SHALL RECOVERY OF ANY KIND AGAINST CANON CANADA BE GREATER THAN THE PURCHASE PRICE OF
THE PRODUCTS SOLD BY CANON CANADA AND CAUSING THE ALLEGED DAMAGE. WITHOUT LIMITING THE FOREGOING, YOU ASSUME ALL RISK
AND LIABILITY FOR LOSS, DAMAGE OR INJURY TO YOU AND YOUR PROPERTY AND TO OTHERS AND THEIR PROPERTY ARISING OUT OF USE,
MISUSE OR INABILITY TO USE THE PRODUCTS NOT CAUSED DIRECTLY BY THE NEGLIGENCE OF CANON CANADA (SOME PROVINCES DO NOT
ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU).
THIS LIMITED WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THE PRODUCTS OR THE PERSON FOR
WHOM IT WAS PURCHASED AS A GIFT.
This warranty gives you specific legal rights, and you may also have other rights which vary from province to province.
CANON CANADA INC.
CANADA
PUB. DIE-0494-001A© CANON INC. 2018
The information in this document is verified as of November 2018. Subject to change without notice.
Visit your local Canon website to download the latest version.
USA http://pro.usa.canon.com
CANON U.S.A., INC.
http://pro.usa.canon.com/support
(855) CINE-EOS (855-246-3367)
(USA only)
UNITED KINGDOM
Canon UK Ltd
Unit 160, Centennial Park, Centennial Avenue,
Elstree, Hertfordshire, WD6 3SG
020-7660-0186
Canon Inc.
30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan
Canon Europa N.V.
Bovenkerkerweg 59, 1185 XB Amstelveen, The Netherlands http://www.canon-europe.com
252

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Canon EOS C700 FF PL bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Canon EOS C700 FF PL in de taal/talen: Engels als bijlage per email.

De handleiding is 16,63 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Stel vragen via chat aan uw handleiding

Stel uw vraag over deze PDF

Andere handleiding(en) van Canon EOS C700 FF PL

Canon EOS C700 FF PL Gebruiksaanwijzing - Deutsch - 269 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info