801630
6
Verklein
Vergroot
Pagina terug
1/106
Pagina verder
6
11. Do not use accessories that are not recommended by the manufacturer. They can be
dangerous to the user and may damage the device.
BEFORE FIRST USE
Check that all connections are completely secure and that the device is securely positioned before using it. The device must be placed
at a distance of at least 1 meters from the nearest wall. The box with the switch must be at least 30 cm from a ceiling and 1.80 meters
above the ground. The device must be placed firmly on an even and completely horizontal surface.
ASSEMBLING
1. Place the lower part of the stand (7) on the round base (6) so that the screw holes align. From the bottom of the base, screw in the
large knob with a metal washer (11).
2. Slide the central part of the stand (8) over the lower part (7). Insert the 4 screws through the double holes and tighten them firmly.
3. Then attach the upper part of the stand (9) to the central part (8). To do this, first insert the thinner adjustable part of the stand (10) into
the upper part of the stand (9). Insert the 4 screws through the double holes and tighten them firmly.
4. Pull out the thinner adjustable part of the stand (10) as far as you want and tighten the fixing knob (5).
5. Put the head housing (1) on the top of the stand (10) and tighten the head with the screw (13) on the back of the head.
6. The head has a vertically adjustable tilt angle in 3 positions, press the head down or up to choose the best angle of heat.
7. The thin part of the stand (10) can rotate 360 °, allowing the head (1) of the device to be directed in any direction. The electric cable
can be attached to the cable holders on the stand.
Device description – picture 1
1. Head housing 2. Grid 3. ON / OFF switch
4. Stand 5. Fixing knob 6. Round base
7. Stand, lower part 8. Stand, central part 9. Stand, upper part
10. Stand, thinner adjustable part 11. Large knob with a metal washer
12. 8 short screws for mounting the stand 13. Screw for securing the head
PATIO HEATER OPERATION
1. Point the head of the device in the correct direction.
2. Insert the plug into the socket (220-240V / 50Hz).
3. The device is switched on and off by the ON/OFF switch (3).
You also select the heating power output with the switch:
0 = 0 Watt
Left: = low power 1000W
Left + Right = high power 2000W
4. The device does not have a thermostat and continues to give out heat until it is switched off. Always keep a close eye on the device
when it is switched on!
5. Remove the plug from the socket when the device is not in use.
Heating element replacement - see page 3
1. Set the power switches to position 0. Disconnect the device from power.
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Camry CR 7737 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Camry CR 7737 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Portugees, Spaans, Pools, Deens, Zweeds als bijlage per email.

De handleiding is 4.01 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info